il sin used for sale

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press WEINGARTEN type ERV 40Masch. No. 537 / 65 Year of construction 1965Compressive force 40 ton. Projection 230 mmTable size 570 x 470 mmPlunger area 250 x 200 mmClamping pin hole 40 mmInstallation height max. approx. 520 mmStroke adjustment 8 - 88 mmPlunger adjustment range 63 mmStroke rate 70 strokes per minuteDrive power 3 kWNetz connection 380 volts, 50 Hz- Table height adjustment- Overload protection by crushing plate- Clutch-brake combination by WEINGARTEN friction threaded coupling-

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

Clamping Table, Sinusoidal Table, Swivel Clamping TableTable Length: 1130 mmTable Width: 300 mmTable Height: 112 mmFolding Angle: 2Folding Angle: max. 7- Folding Angle 2 via Threaded Spindle Folding Bracket max. 7 manually raised to the stopOverall Dimensions L x W x H: 1450 x 300 x 112 mmWeight: 275 kgGood ConditionClamping Plate, Ideal for Making Wedge Strips; used

We are selling our die-sinking EDM system here because of a new acquisition. This is a machine that was sold by the company MATRA at that time. This is a DECKEL DE35C. In the meantime, the company Exeron has taken over the service. The travel is: X=600mm Y=400mm Z=400mm The die-sinking EDM system has a 4-fold electrode changer The control system on the machine was recently overhauled, the power supply and the UPS were renewed. The machine was also otherwise continuously checked and maintained by the Exeron company in the event of malfunctions. Machine is running and is still on the power for a possible test. Operating hours are: 33196 hours. Various tool holders can be part of the price negotiation.

pressure: 20 t throat: 200 mm stroke: 0 - 50 mm table:: 360 x 550 mm table:: 140 mm - Bohrung no. of strokes: 160 Hub/min bore: 35,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 240 mm total power requirement: 2,2 kW weight: 1.250 kg range L-W-H: 1310 x 1250 x 1860 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 100 t

Sale due to switch to eccentric press Pressing force 100 tons Loading depth 360 mm Stroke 500 mm Daylight 800 mm Plunger area 530 x 400 mm Table height above floor 710 mm Working speed 10mm/sec Approach speed 150 mm/sec Return speed 150 mm/sec Required power 17 kW Dimensions L x W x H 1,400 x 2,000 x 3,200 mm Weight of the machine approx. 5.1 t Year of manufacture 2001 Price is net, VAT can be claimed. Loading facilities available All information without guarantee

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

pressure: 63 t throat: 260 mm stroke: 8-100 mm ram - range of adjustment: 63 mm no. of strokes: 115 Hub/min : 316 mm table surface area: 630x490 mm ram surface: 315x260 mm hole in the table: Ø 140 mm total power requirement: 4 kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: 2000x2000x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single Column Press Dunkes TYPE: HZS 160 Specifications: Manufacturer: Dunkes Model: HZS 160 Operating hours: approx. 2250 The machine is in good condition and fully functional.

A bevel gear rolling test machine Gleason is available. Workpiece diameter: 330mm, max. center distance: 203mm, driver spindle nose distance range: 100mm-250mm, max. offset range upper/lower: 203mm/50mm, driver spindle bore: 99mm, driver spindle taper per meter: 15.5mm/m, counter spindle bore: 58mm, counter spindle taper per meter: 12.7mm/m, spindle speed: 1500rpm, test angle range: 0°-180°, driver spindle repeatability: +/-0.004mm, runout: +/-0.003mm, machine dimensions X/Y: approx. 1550mm/2050mm, weight: approx. 2400kg. An on-site inspection is possible.

Holzzerkleinerer ( Holzhäckler ) maschine modell MION MOSOLE TR 2 gebrauchte maschine Maschinenbedienung im Automatik- und/oder Handbetrieb modus Arbeitsbedingungen: ausgezeichnet Im Automatikbetrieb startet der Motor in die entgegengesetzte Richtung, um den Stopfer von eventuellen Rückständen vorheriger Arbeiten zu befreien. Im Vollautomatikbetrieb stoppt der Motor nach ca. 5 Sekunden und startet erneut in die richtige Richtung für eine kontinuierliche Bearbeitung (siehe Video). Technische Daten : hydraulischer Schieber Breite Rotor mm.700 Durchmesser Rotor mm.300 Drehzahl Zerkleinerungseinheit 100 U/min Trichterinhalt 3.42 m³ Hauptmotor PS 25 Hydraulikaggregat Motorschieber PS 1 auswechselbare Messer Beschickung von oben

Charmilles Form 20 Tabledimensions / T slots : 398,8 × 299,7 mm Tank dimensions: 208,2 L Longitidinal displacement X-axes: 300 mm Transversal displacement Y -axes: 200 mm Vertical displacement Z-axes: 250 mm Max weight on table: 350 kg

Planetary Gearbox PCEF53.5-X1 New For Doppstadt DW2560B, DW3060 standard, mobile & stationary Not suitable for Biopower models (42 teeth on the roller)! Fully assembled with output flange and driver

Komptech Terminator 5000 SD Category: Garbage Shredders Specification: Category: Universal Waste Shredder Serial / reference number: 481148 Power: 446 hp / 328 kW Weight: 27 000 kg Emission class: Tier 4 Final / Stage V Equipment and description: Terminator 5000 S Diesel engine: CAT C13 Tier 4 Final/Stage V F-Crushing Unit Armoured rollers – new Sickle teeth Hydraulically adjustable cutting gap 0-45 mm Overbelt magnet Central lubrication Remote control

Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg

Height=0.82 m, Overall length= 1.01 m, Overall width= 1.12 m, In store Made in Denmark Description Capacity of 800 – 1000 trays per hour 3 main brushes for cleaning made of polyamide 2 brushes for cleaning of perforated trays All brushes can be adjusted individually to prolong the lifespan Quick copuling system for the cleaning brushes. (Un-/mounting without tools). Easy fix-System for main cleaning brushes The whole machine can be cleaned with water External oil container with sight glass and circulation pump Mobil scrapings container

Screw Diameter: 75 mm // Throughput: 700 kg/h

Screw Diameter: 35 mm // Output Capacity: 25 kg/h

Screw Diameter: 160 mm // Output Capacity: 1400 kg/h

Screw Diameter: 100 mm // Output Capacity: 600 kg/h

Screw Diameter: 65 mm // Output Capacity: 170 kg/h

1 YAMADA Single End Sizing Winding machine Mod. YS-6 12 spindles year of construction 1998 with YAMADA TFB meter counter on each spindle squeeze roller sizing application type non-touch yarn break control sensor on each spindle take-up cylindrical traverse 150 mm (6 inch)

pressure: 150 t throat: 400 mm stroke: 400 mm dayligth: 600 mm table surface area: 1000 x 600 mm Control: Siemens S7 hole in the table: 0 mm table height over floor: mm ram surface: 1000 x 600 mm working feed: 5 - 15 mm/sec speed down: 130 mm/sek speed up: 180 mm/sek power requirement: 18 kW weight of the machine ca.: 12,0 t dimensions: 2,4 x 1,9 x 3,5 m Single-column press with - Hardened and chrome-plated cylinder - Main cylinder diameter 270 mm - Auxiliary cylinder diameter 70 mm - Bosch Rextroth pump, valves, and filters - Hydraulic overload valve - Hydraulic proportional valve - Siemens touchscreen control panel with remote maintenance access Settings for stroke, pressure, speed, and dwell time - Category 4 sensors and photoelectric sensor - Two-hand control panel with reset and emergency stop buttons - CE marking The data for this ad was created with ModulMWS - the software solu ...

This 3-axis Makino EDNC 30 die-sinking EDM machine was manufactured in 1998. It features travel paths of 300mm in X, 250mm in Y, and 250mm in Z, a table size of 500 × 350 mm, and can handle a maximum workpiece weight of 500 kg. Consider the opportunity to buy this Makino EDNC 30 die-sinking EDM machine. Contact us for more information about this machine.

This 3-axis AGIE AGIETRON Innovation 2 die-sinking EDM machine was manufactured in 2002. It features a robust AGIEVISION control system, a 28-position electrode changer, and a C-axis for rotation, indexing, and erosion. The machine can handle workpieces up to 650 x 580 x 250 mm and 400 kg. It boasts a high-performance AGIE IPG generator with a removal rate of 450 mm³/min for copper/steel. Consider the opportunity to buy this AGIE AGIETRON Innovation 2. Contact us for more information.

This 4-axis PENTA 1060 CNC die-sinking EDM machine was manufactured in 2014. Ideal for detailed and precise metalwork, it offers advanced control and efficiency. Consider the opportunity to buy this PENTA 1060 CNC die-sinking EDM machine. Contact us for more information.

This CHARMILLES ROBOFORM 51 Erosion machine was made in 1998. The machine has a table size of 750x500 mm.

This Mitsubishi Electric SG12M die-sinking EDM machine was manufactured in 2020. It features a robust 3750 kg weight, with a maximum workpiece weight capacity of 1000 kg. The machine includes a dielectric fluid chiller unit and a dual paper filter system, ensuring optimal operational conditions. The working tank has an automatic elevation system and hinji open-door for ease of use. If you are looking to get high-quality die-sinking capabilities, consider the Mitsubishi Electric SG12M machine we have for sale. Contact us for more information.

This 3-axis CHARMILLES HD10 start hole drilling machine was manufactured in 2002. It features a work table size of 600x300mm, XY-travel of 350x250mm, and can handle a maximum workpiece weight of 450kg. Ideal for precise erosion tasks, the CHARMILLES HD10 machine we have for sale represents a robust addition to any machining setup. Contact us for further details regarding this machine.

This 4-axis Exeron EDM 310 MF20 was manufactured in 2006. Ideal for precision die-sinking applications, it offers robust performance and reliability. If you are looking to get high-quality die-sinking capabilities, consider the Exeron EDM 310 MF20 machine we have for sale. Contact us for more information.

This 6-axis VOLLMER QXD 250 grinding machine was manufactured in 2017. It features a robust 3 Phase 380Volts, 50hz, 8.7KVA power supply and a substantial coolant tank capacity of 310 liters. With a machine weight of 7,200kg and comprehensive axis movement, including a 360-degree swivel angle on the A-Axis and +/-20 degrees on the B-Axis, consider the opportunity to buy this VOLLMER QXD 250 grinding machine. Contact us for more information about this machine.

pressure: 40 t stroke: 150 mm serial number: 100091 : 2 : Druck & Hub verstellbar pressure: 25 t weight: je 1,5 t safety light frame: ja bei beiden The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t throat: 250 mm stroke: 400 mm dayligth: 500 mm table surface area: 800 x 500 mm Control: Siemens S7 hole in the table: 0 mm table height over floor: 500 mm ram surface: 800 x 500 mm working feed: 10 mm/sec speed down: 110 mm/sek speed up: 160 mm/sek power requirement: 11,0 kW weight of the machine ca.: 5,5 t dimensions: 1,9 x 1,7 x 2,9 m Single-column press with - Hardened and chrome-plated cylinder - Main cylinder diameter 220 mm - Auxiliary cylinder diameter 50 mm - Bosch Rextroth pump, valves, and filters - Hydraulic overload valve - Hydraulic proportional valve - Siemens touchscreen control panel with remote maintenance access Settings for stroke, pressure, speed, and dwell time - Category 4 sensors and photoelectric sensor - Two-hand control panel with reset and emergency stop buttons - CE marking The data for this ad was created with ModulMWS - the software solut ...

Press force: 100t, throat depth: 320mm, table dimensions X/Y: 850mm/610mm, ram dimensions X/Y: 600mm/355mm, stroke range: 10mm-130mm, ram adjustment: 80mm, stroke rate: 56rpm, installation height: 300mm, machine dimensions X/Y/Z: approx. 1900mm/1900mm/3150mm, weight: approx. 9000kg. On-site inspection is possible.

Extrudeuse CM EVOLUTION PLAST type CM-EVO 230 Année. : 2019 Puissance : 50 KW Tension : 400 VOLTS Poids : 4000 KG

Key data: 1770 A, 1220 , 70

The OPS INGERSOLL EDM machine GANTRY 1200 HSJ / 64 bit, built in 2006, has been comprehensively and professionally overhauled in our company and is in very good condition, both technically and visually. In the course of the overhaul, more than 70% of the machine was dismantled. All relevant wear parts have been carefully checked. The following overhaul work was carried out on the above-mentioned machine: Replacement of ball screw and ball bearings of the X, Y and Z axis. Replacement of all (4) ball screws of the tank drive. Inspection and test of the C-axis for tightness and accuracy Geometric verification of all axes according to OPS INGERSOLL protocol. Basic cleaning of the complete machine base. Cleaning of the complete working tank including replacement of the felt scrapers. Complete painting of the machine. Overhaul of the dielectric pumps. Replacemen ...

Key data: 750 mm, 650 mm, 60 A

Refurbished OPS Ingersoll Gantry 500 Eagle die-sinking EDM machine – technically and visually in top condition The machine has been comprehensively and professionally overhauled in our company and is in very good condition, both technically and visually. In the course of the overhaul, more than 70% of the machine was dismantled. All relevant wear parts were carefully checked and replaced if necessary, including ball rollers and drive spindles. This was followed by a complete geometric measurement, alignment and additional control using a laser measuring system. The machine bed and the entire base were thoroughly cleaned. All pumps were disassembled, cleaned and overhauled. All hoses, including hydraulic and compressed air hoses, have been completely renewed. In addition, the machine has been completely repainted and also presents itself visually in a very neat condition.  ...

Technical features: heated knives, weld bead limitation 0.2mm, optimization of the welding result through the parallel sliding welding process, individual adjustment of the welding parameters, quick changing of the outer contour allowances by means of holding magnets. Air consumption at 6bar: 15l/Takt, angle adjustment range: 30-180°, profile height: 30-105mm, max. profile width at 90°: 157mm, compressed air connection: 8.7bar, power: 2.7kW, supply voltage: 220V, 50/60Hz, length: 770mm, width: 880mm, height: 1560mm, weight: 320kg. An inspection on site is possible.

This 3s Sodick AG55L die-sinking edm machine was manufactured in 2008. With a magazine capacity of 32 positions and a maximum workpiece weight of 1000 kg, it offers robust capabilities for precision machining. The X travel reaches 550 mm and Y travel extends to 400 mm, making it suitable for various applications. Consider the opportunity to buy this Sodick AG55L die-sinking edm machine. Contact us for further details.

This 3-axis CDM Rovella BF 600 die-sinking EDM machine was manufactured in 1997. It features a 1400x700 mm working area and comes with equipment included. If you are looking to get high-quality die-sinking capabilities, consider the CDM Rovella BF 600 machine we have for sale. Contact us for more information about this machine.

Key data: 100 t

For sale is a hydraulic single-column press (C-frame) from the manufacturer Durendus with an adjustable press force of up to 100 T. The machine has a table size of 800 × 600 mm, a maximum installation height of 700 mm and an adjustable stroke of up to 500 mm, making it suitable for a wide range of pressing, assembly and forming work in industry and production. The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. Here are the technical data of the offered machine: Technical data + information: Hydraulic Single Post Press – C-Frame – 100 T Allgemeine Disclosures - Title: Hydraulic Single Column Press - Type: C-frame / single-column press - Manufacturer: DURENDUS - Press force: 15–100 T (adjustable) - Max. installation heigh ...

Press force: 250kN, Operating pressure: 280bar, Stroke: 300mm, Installation height: 500mm, Reach: 250mm, Oil filling: 280l, Ram speed: 105mm/s, Weight: approx. 2550kg. Documentation available. An on-site inspection is possible.