hydraulic pressbrake used for sale

Hydraulic Pump Manufacturer : Rexroth / Brueninghaus Article: L A6VM 250 HD3 / 63W -VZB - B - SO154 Condition : New

Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: 40 mm -Piston rod: Ø 25 mm -Stroke: 320 mm -universally applicable: -Number: 1x available -Price: per piece -Dimensions: 51/64/H530 mm -Weight: 4.75 kg

Tie rod cylinders, hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston: Ø approx. 50 mm -Piston rod: Ø 25 mm -Stroke: 190 mm -Dimensions: 75/75/H550 mm -Weight: 8.4 kg

Tie rod cylinder, hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -Piston: Ø approx. 35 mm -Piston rod: Ø 20 mm -Stroke: 40 mm -Dimensions: 65/65/H380 mm -Weight: 3.75 kg

Hydraulic Pump Manufacturer : Rexroth / Brueninghaus Article: AL A6VM 355 HD2D / 63W 2-VZH157D B-S0167 Condition : New

6500ton Open Die Forging Press HJ / Seonam (Korea) Design: Eastern European Corporation Installation: 2006/2008 Press Type: Four column push down Oil hydraulic system Nominal force (static working pressure of 320 bar): 5,000 Tons Up-setting force (static working pressure of 420 bar): 6500 Tons Daylight: 5,200 mm Stroke of Movable cross head: 2,700 mm Main Ram dia. (Center cylinder): 1 set - ￠950 mm Side Ram dia. (Side cylinder): 2 sets - ￠750 mm Return cylinder Ram dia: 2 sets - ￠300 mm Moving Table Width: 2,600×Length 6,600 mm Moving Table stroke (center to both side 2,750mm): 5,500 mm Approaching speed: 300 mm/sec Main cylinder Forging speed (2,200 tons/ 320 bar): 163 mm/sec All cylinder Forging speed (5,000 tons/ 320 bar): 73 mm/sec Up-setting Forging speed (6,500 tons/ 420 bar): 10 mm/sec Return speed: 270 mm/sec Hydraulic Main pump: 12 sets  ...

Offer 24295 Specifications: - max. working width 3050 mm - max. cutting capacity St 40 16 mm - Projection 270 mm - Cutting angle 2.4 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 16 pcs - Motor back gauge with positioning control 20 - 1000 mm - Front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 7 - 18 rpm - Hydraulic drive 400 V / 30 kW - Table height approx. 820 mm - Space required including back gauge, without front support arms -ca. W 4000 x H 2400 x D 2400 mm - Weight approx. 14500 kg - with: - E-foot switch - Cutting Line Illumination - - Cutting Length Selection - Rear area protection with light barrier

Clamping bush, hydraulic clamping bush -Type: ETP-EXPRESS R-25 -Flange: O 58 mm -Flange width: 14 mm -Shaft: Ø 30 mm -Shaft length: 35 mm -Bore: 25 mm -Dimensions: Ø 58/H49 mm -Number: 4x available -Price: per piece -Weight: 0.27 kg/piece

Key data: 30 t

Hydraulic press can be used in a variety of ways as an assembly press, small series press, manual insert press or heating press in double-column presses Design (H-press) A tour of the press is possible at the Ennepetal camp. It is a 2.5-year-old, unused press with no operating hours, which is sold with a full warranty. List price: 45,000 Technical details: Robust machine frame Capacity: 30 tons – at 300 bar Pump ASC: 28.5 liters/min. Engine: 11 kW – 15 hp Oil tank: 600 × 450 × 500 mm – with approx. 100 litres Cylinder piston: Ø 110 mm Cylinder inside: Ø 70 mm Stroke: 500 mm Fast forward: 45 mm/s Return: 55 mm/s Guides: Ø 50 mm Table top: 800 × 550 mm – with T-slots Plunger plate: 700 × 500 mm – with T-slots Total weight: 2000 kg Valves from BoschRexroth Control cabinet technology from renowned manufacturers Press table size 700 × 500 × 7 ...

Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: 25 mm -Piston rod: Ø 16 mm -Stroke: 260 mm -Admission piston rod: M10 mm -universally applicable: -Number: 1x cylinder available -Price: per piece -Dimensions: 457/43/H38 mm -Weight: 2.45 kg/piece

feed under pressure: 2,7 mm/sec pressure: 100 t stroke: 400 mm table surface area: 920 x 560 mm feed down: 4,25 mm/sec feed up: 8,22 mm/sec oil pressure max. in the work cylinder: 385 bar oil volume: 26 l diameter of piston: 125 mm column daylight: 920 mm voltage: 400 V/ 50 Hz total power requirement: 4 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,7 x 0,9 x 2,1 m • unused workshop press, • manual and hydraulical operation, • pressure cylinder horizontally moveable, • table can be hydraulically adjust in height, • Cylinder Ø 175 mm, piston base Ø 125 mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Qty. 1 Second-hand 160 MN Horizontal Direct Single Action Extrusion Press Mfc.: SMS Force: 16 000 MT Built: 2015/2016 Billet dim.: Dia. 610/720 x 750 – 2500 mm Scope of supply: Induction Billet Furnace Extrusion Press Quenching System Puller Run-Out Table Stretcher Finishing Saw Profile Stacker Die Oven Billet Peeling Machine

Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: 25 mm -Piston rod: Ø 12 mm -Stroke: 50 mm -Admission piston rod: M10 mm -universally applicable: -Number: 1x cylinder available -Price: per piece -Dimensions: 242/43/H38 mm -Weight: 1.37 kg/piece

Key data: 2200 t

Qty. 1 Second-hand extrusion press – 2200 MT Mfc.: Breda Danieli Built: 2016 Status: still in production Max. Extrusion Force: 21,9 MN at 300 bar Max. working pressure: 310 bar Type of press: back loading with 2 containers Billet size 8” - length: 300 – 1,200 mm Scope of supply: complete extrusion press in working order with hydraulic and electric system Overhead pinch billet manipulator Material: AL 6000 Series Out of the scope of supply: floor frame mounted in the concrete floor all dies and tooling bolsters

Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: 38 mm -Piston rod: Ø 25 mm (M20 x 1.5 mm thread) -Stroke: 60 mm -Pressure: 70 bar -universally applicable: -Dimensions: 224/86/H53 mm -Weight: 2.5 kg

Nominal force 1250 ton - first stage : 260 tons, - second stage : 800 tons, - third stage : 1250 tons, Slide stroke 1250 mm Distance between table and slide 2650 mm Main cylinder dia Ø 500mm Return cylinder dia. ( two) 2xØ400mm Distance between column 1800mm Table size width / length 1250 / 3150 mm Main motor power 150 kW Machine dimensions L x W x H 16950 x 12100 x 11410 mm Weight 265000 kg Forging manipulator FS2ЕТС -2T also available 1T and 700t

Hydraulic cylinder, synchronous cylinder, steering cylinder -Piston diameter: 38 mm -Piston rod: Ø 16 mm (M12 thread) -Stroke: 20 mm -Dimensions: 234/89/H50 mm -Weight: 3 kg

Double hydraulic pump, oil pump, gear pump Manufacturer: ATOS -Rotor pump type: PFED-43056/022/1DTO -Shaft diameter: 22 mm -Number: 4 pumps available - Price: per piece -Dimensions: 175/325/H195 mm -Weight: 28 kg

Double hydraulic pump, oil pump, gear pump -Manufacturer: ATOS -Rotor pump type: PFED-54129/029/1DTO -Shaft diameter: 32 mm -Number: 3 pumps available -Price: per piece -Dimensions: 215/355/H220 mm -Weight: 44 kg

to move the heaviest loads Total thrust 400 to - 4 x 100 to Cylinder stroke approx. 1,000 mm Double-acting hollow piston cylinders Tie rods 9 x 6,000 mm, 1 x 5,000 mm Operating pressure up to 400 bar Tank capacity approx. 500 litres Operation via wired remote control Electrical values 400 V / 2 x 30 KW

pressure: 200 t stroke: 150 mm table surface area: 850x650 mm ram surface: 730x560 mm weight of the machine ca.: 8 t dimensions of the machine ca.: BxTxH 2000x2500x3600mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Double hydraulic pump, oil pump, gear pump -Manufacturer: ATOS -Rotor pump type: PFED-54150/085/1DTO -Shaft diameter: 32 mm -Number: 3 pumps available -Price: per piece -Dimensions: 215/355/H220 mm -Weight: 44 kg

Payload 10,000 kg Rope diameter 22 mm x 150 meters length as specified in the documentation Operating pressure 55 bar to max. 80 bar Flow rate 19 litres / min to max. 272 litres / min Rexroth hydraulic motor Hydraulic control block with mounting base Documentation and test book available The winch was used on a test bench / test tower. Space requirement L - 2,100 x D - 1,400 x H - 1,300 mm complete with control block Weight approx. 1,500 kg

Double hydraulic pump, oil pump, gear pump -PTO shaft diameter: Ø 34 mm Quantity: 1 piece available -Dimensions: 440/180/H155 mm -Weight: 35 kg

Hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -single-acting cylinder -Piston diameter: approx. 55 mm -Piston rod: Ø 50 mm -Cylinder tube outer diameter: Ø 70 mm -Stroke: 300 mm -Total length when retracted: 552 mm -Piston rod mounting: Ø 30 mm -Universally applicable: -Number: 16 cylinders available -Price: per piece -Dimensions: 1350/80/H100 mm -Weight: 33 kg/piece

hydraulic outriggers for loader cranes Stroke 500 mm Stable design with guide via square tube Mechanically telescopic with bolt 300 mm - grid 100 mm Outer square tube 100 x 100 mm Folding device for support cylinder - can also be dismantled Outriggers can be folded down approx. 60° Retracted height 1,000 mm with folding device with integrated load holding valve Removable support plate - size 320 x 250 mm Weight 80 kg / piece - New - unused - 2 pieces in stock - unit price -

Hydraulic power pack, hydraulic pump, hydraulic pump -Electric motor -Motor power: 5.5 kW -Speed: 1435 rpm -Hydraulic pump -Max. Pressure: 60 bar -Liter output: 50 l/min -Dimensions: 720/640/H700 mm -Weight: 145 kg

Hydraulic cylinder for ATLAS loader crane Stroke 750 mm Piston rod 125 mm Outer diameter cylinder tube 235 mm Piston diameter approx. 200 mm Length retracted center - center bolt 1,100 mm Bolt diameter cylinder tube 80 mm Width of the mount 245 mm Bolt diameter 100 mm Both bolt mounts with plain bearings Spare part number original Atlas 4189526 Width of the piston rod holder 130 mm Weight approx. 330 kg / piece Original price approx. € 9,500,-- -New- - 2 pieces in stock - price per piece -

Hydraulic power unit, hydraulic pump, hydraulic pump -Drive: 7.5 kW 1440 rpm -Dimensions: 360/310/H660 mm -Weight: 86 kg

Hydraulic power pack, hydraulic pump, hydraulic pump -Electric motor SIDO type: D160L-84 -Motor power: 7.5/12 kW -Speed: 720/1435 rpm -Hydraulic pump Sperry Vickers type: GC4/40/3/10 -Max. Pressure: bar -Dimensions: 960/400/H520 mm -Weight: 242 kg

pressure: 40 t throat: 320 mm stroke: 250 mm arm length: 320 mm table surface area: 1400x600 mm ram surface: 1200x600 mm dayligth: 650 mm total power requirement: 22 kW weight of the machine ca.: 8 t dimensions of the machine ca.: 3200x3300x3300 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t throat: 380 mm stroke: 300 mm arm length: 380 mm table surface area: 1700x700 mm ram surface: 1400x700 mm dayligth: 650 mm total power requirement: 30 kW weight of the machine ca.: 10 t dimensions of the machine ca.: 2400x3600x3400 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic pump, oil pump, hydraulic power pack, hydraulic pump, hydraulic pump, electric motor, DC motor, traction motor, drive motor -Gear pump: for electric forklifts -Bicycle pump type: -with tank and control valve -Drive: 24 V -Dimensions: 285/280/H750 mm -Weight: 38 kg

Hydraulic pump, oil pump, gear pump -Drive: 2.2 kW 1420 rpm -Dimensions: 550/280/H260 mm -Weight: 40 kg

Hydraulic motor, oil motor, hydraulic pump -Hydraulic motor for: the drive of work platforms from GSL (German Standard Lift) -Admission wheel recess: Ø 160 mm -universal: applicable -Number: 2x motors available -Price: per piece -Dimensions: 190/190/H342 mm -Weight: 70 kg/piece

pressure: 25 t stroke: 100 mm table surface area: 440x320 mm ram surface: 360x220 mm hole in the table: 160x100 mm table height: 900 mm tool hole in ram: Ø 40 mm dayligth: 280 mm weight of the machine ca.: 1,5 t dimensions of the machine ca.: BxTxH 1500x1500x2100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t throat: 380 mm stroke: 400 mm power capacity: 22 kW dayligth: 600 mm ram surface: 600x500 mm table surface area: 720x600 mm weight of the machine ca.: 9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic motor, oil motor, hydraulic pump -Hydraulic motor for: the drive of work platforms from GSL (German Standard Lift) -Toothed shaft holder: Ø 25 mm -Length: 25 mm -universal applicable -Number: 2x motors available -Price: per piece -Dimensions: 290/160/H160 mm -Weight: 13.5 kg

pressure: 25 t throat: 250 mm stroke: 100 mm ram surface: 500x400 mm hole in the table: Ø 110 mm table height: 850 mm tool hole in ram: Ø 40 mm ram surface: Ø 150 mm weight of the machine ca.: 2,5 t dimensions of the machine ca.: 1500x2000x2200 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 t distance between columns: 625 mm stroke: 150 mm table surface area: 580x450 mm ram surface: 580x340 mm hole in the table: Ø 150 mm table height: 850 mm tool hole in ram: Ø 45 mm column travel -side: 200x200 mm weight of the machine ca.: ca. 6,0 t dimensions of the machine ca.: BxTxH ca. 1300x1300x2750 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic motor, oil motor, hydraulic pump -Hydraulic motor for: the drive of work platforms from GSL (German Standard Lift) -Shaft cone holder: Ø 35 to Ø 41 mm -Cone length: 60 mm -universal: applicable -Number: 1x motors available -Price: per piece -Dimensions: 365/150/H150 mm -Weight: 23 kg

Hydraulic vise, machine vise, hydraulic vise, high-pressure clamp, hydraulic vise -hydraulic tension defective -sold as a source of spare parts -Jaw width: 160 mm -Jaw height: 53 mm -Span: max. 170 mm -Support height: 80 mm -Weight: 62 kg

Hydraulic power pack, hydraulic pump, hydraulic pump -Max. Pressure: 25 l/min -Hydraulic tank: mm -Motor: kW rpm -Hydraulic valve -Pressure relief valve -pressure clock -Filter -Dimensions: 500/800/H850 mm -Weight: 248 kg

pressure: 100 t throat: 275 mm stroke: 150 mm table surface area: 860x550 mm ram surface: 600x400 mm table height: 810 mm tool hole in ram: Ø 50 mm dayligth: max. 475 mm weight of the machine ca.: 7 t dimensions of the machine ca.: BxTxH 2000x2500x3300 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 t distance between columns: 0 mm stroke: 0 mm total power requirement: 0 kW weight of the machine ca.: 0 t dimensions of the machine ca.: 0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic pump, oil pump, gear pump -Pumps: are unused -Contents: approx. 20 l -Electric: 24 V 3 KW -Working pressure: 140 bar -Number: 13x pumps available -Price: per piece -Dimensions: 900/175/H210 mm -Weight: 24 kg

pressure: 25 t distance between columns: 800 mm stroke: 100 mm dayligth: 450 mm table surface area: 750x750 mm weight of the machine ca.: 3 t dimensions of the machine ca.: 1500x1500x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1500 mm plate thickness: 3 mm weight of the machine ca.: 4 t dimensions of the machine ca.: BxTxH 2000x1500x1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic power pack, hydraulic pump, hydraulic pump -Max. Pressure: 60 bar -Liter output: 5.5 l/min -Hydraulic tank: 450/320/H320 mm -Motor: 0.75 kW 1400 rpm -Hydraulic valve -Pressure relief valve -pressure clock -Dimensions: 520/330/H600 mm -Weight: 100 kg

Double hydraulic pump, oil pump, gear pump -double pump -Power: 2.2 kW 1420 rpm -Protection class: IP 55 -Dimensions: 585/263/H238 mm -Weight: 43 kg