hydraulic press used for sale

Hydraulic power unit with hydraulic pump RACINE / VICKERSHydraulik gensetOperating pressure: max. 44 barVolume flow: 13 litres/min. Tank capacity: 40 litersEngine speed: 950 rpm. Engine power: 0.75 kWNetz connection: 380 Volt, 50 Hz- 1 piece hydraulic vane pump PVQ-PSS=-06CR-J11- Hydraulic tank with maintenance cover and oil level sight glass- 2 pieces hydraulic hoses with 12L connections, length = 950 mmSpace requirement L x W x H:: 700 x 400 x 750 mmWeight: 97 kg (without oil content); used

Hydraulics Machine viseJaw width: 130 mmJaw height: 46 mmClamping force: 4 ton. Clamping range: 0 to 220 mmOpening width: max 223 mmGuideway height: 72 mm- 3 clamping ranges adjustable via plug-in pins, 0 to 79mm, 67 to 151 mm and 139 to 223 mmDimensions L x W x H: 535 x 210 x 119 mmWeight: 35 kgvery good condition; used

Hydraulic scissor lift table GRUSE type ELS 0.5-8-1-G-SOFabr. No: 124984 year of construction 2017Load capacity 300 kgPlatform size 1250 x 800 mmUsable stroke max. 785 mmOverall height - table bottom 345 mmOverall height - table top 1130 mmEngine power 0.8 kWNet connection 400 volts, 50 Hz- Foot switch for up and down, with emergency stop and key switch for control One- Single scissors with a lifting cylinder- Circumferential safety contact strip with limit switches under the upper frame- Adjustable limit switch for the upper stroke restriction-

Single column pneumatic press, hydraulic press PAUL ANTON type PVT 2Pneumatic table press, embossing pressFabr. No. 97148 Year of construction approx. 1980Compressive force: 10 tonProjection: 100 mmPlunger stroke: approx. 25 mmPlunger surface: 32 mmTable size: 250 x 220 mmTable opening: 53 x 53 mmTable height: 1060 mmInstallation height: 155 mm- very stable construction- Hydro-pneumatic press with pressure transmission air on oil- pneumatic foot switch- Plunger with internal thread M12- Metal substructureSpace requirement L x W x H 850 x 620 x 1560 mmWeight

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

table 500/600 mm

Used hydraulic press PHW 12

Hydraulic cylinder filter press Chamber filter press New, used and refurbished Ask us.

Mapelli 300ton downstroke hydraulic presses with vacuum, Type T300, year 1990, 4 column type, with pneumatic front guard, fixed guards to sides and rear, main ram dia 450mm, with pull back rams, single daylight 500mm, with 600mm wide x 700mm electrically heated platens. With hydraulic power unit mounted on top. Complete with controls etc and in good condition.

1 x Wickert 500ton upstroke vacuum press, Type: WKP5000/5/3, Year of manufacture: 1997, Machine Number: 2885 with 500mm x 500mm electrically heated platens, sliding bottom platen with ejector table, Daylight: 340mm 400/690V, 50Hz, 22kW. Heaters 12.5kW, Pressure 300 Bar Fixed guarding to rear, SICK light curtain guards to the front. With Siemens S5 PLC controls. In very good condition.

SMG DS 315-1500/1300 CNC hydraulic press was manufactured in 1984 in Germany. The machine, consisting of two interconnected stations, is used for pressing metal workpieces in manual, semi-automatic and automatic mode with a pressing force of up to 315 tonnes. All the machine’s machining parameters are set using a CNC control with a full-colour, touchscreen display. The press is equipped with a hydraulic and pneumatic sheet metal feeder, servo drives for feed rollers to set a very precise stroke of up to 0.1 mm, safety cages and workpiece feed and drop control sensors. The SMG 315 T machine underwent a complete overhaul in 2007, during which components such as pumps and safety installations were replaced. Technical data of the SMG DS 315-1500/1300 press - maximum press force: 315 t - working table dimensions (L x W): 1500 x 1300 mm - upper machine point (from the table): 750 mm ...

JJZ-CP type press designed for the production of plywood, doors, MDF. The glued elements are fed and removed from the press automatically by means of driven rollers. The press can be used with glue feeders. Specifications: -max. pressure 500T/ adjustable/ -max. load height 1300mm -max. batch size 1300x2500 -press size 3600x1370x4500 mm -press foundation ~500 mm below the floor level -feeding table 2000x1960 mm -receiving table 2350x2500 mm -max. power 13.2 kW -Ce -capacity of 6 batches per hour Currently, we glue panel doors and MDF board on presses. Very good technical condition. We offer a plywood production line dedicated to these presses.

Hydraulic pressure filter, 200bar, 34P-0014, Parker, used - overhauled Special price (The cheapest current new price in the market is more mthan € 3000 excl. VAT) If you have a VAT number, we will gladly issue you an invoice without VAT. Used part - overhauled! The part was purchased from a company's spare parts warehouse, has been overhauled, reconditioned and is fully functional. Manufacturer Type designation: 34P-0014 Max. operating pressure 200 bar 565L/min Micron Rating 20Q G1 1/4" incl. new filter element Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the seller, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclude  ...

Hydraulic pressure filter, 200bar, 34P-0016, Parker, used - overhauled Special price (The cheapest current new price in the market is more mthan € 3000 excl. VAT) If you have a VAT number, we will gladly issue you an invoice without VAT. Used part - overhauled! The part was purchased from a company's spare parts warehouse, has been overhauled, reconditioned and is fully functional. Manufacturer Type designation: 34P-0016 Max. operating pressure 200 bar 565L/min Micron Rating 20Q G1 1/4" incl. new filter element Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the seller, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclud ...

ULTRAPRAS UPV100TT SPECIAL hydraulic press built in 2022 Poland is the perfect choice for a range of demanding cold metal forming operations. This highly efficient and versatile machine can perform such operations as precision bending, profiling, flattening, bending, hole punching and stamping. Inside the robust design, there is a power unit-powered hydraulic piston with a diameter of 220 mm, which performs all these machining processes with a high press force of 100 tonnes. In addition, the entire working area is protected by light curtains, thanks to which the UltraPras four-column press also offers a high level of operational safety. During its service life, the machine has operated for just 595 hours and completed a total of 37042 work cycles. The UPV 100 TT SPECJAL 100t hydraulic press weighs 6500 kg. Technical specifications of the ULTRAPRAS UPV100TT SPECIAL press - maximum pre ...

Description of the chip press: Powerful metal chip press with chip shredder for long turnings. The area of application is the processing of large quantities of milled and turning chips. Materials: aluminum, steel, cast iron Drip pan as oil tank Geared motor for optimal agitator operation Hydraulic Compression Cylinder Hydraulic press cylinder with two coaxial sections Diameter of briquettes 60 mm Automatic briquette length adjustment with displacement transducers Inductive Proximity Sensors Pre-compaction cylinder in conjunction with special compression hydraulic cylinder that compacts the material in the bushing-bulkhead unit Briquette ejection system, consisting of a compression chamber and a bulkhead with special anti-wear treatment Highly efficient closed-circuit oil cooling system consisting of an air/oil heat exchanger Hydraulic system with B ...

ULTRAPRAS WKR70H hydraulic press built in 2021 by the Polish company SAKOMET is designed for even the most demanding cold metal forming operations. The operations, such as precise cutting, stamping, punching and extruding of workpieces, are performed with a force of 16 tonnes using a hydraulic cylinder with a diameter of 100 mm. Induction limiters additionally allow adjustment of the piston advance and retraction limits, making the machine adaptable to the working range of various tools. In turn, centrally beneath the piston is a large cross-cut work table with a 90mm diameter bore. The UltraPras WKR 70H 16t hydraulic press weighs 420 kg. Technical specifications of the ULTRAPRAS WKR70H press - press force: 16 t - piston stroke: 70 mm - piston diameter: 100 mm - maximum working speed: 9.8 mm/s - minimum working speed: 2 mm/s - return speed: 20 mm/s - work table dimensions (L x  ...

ZM 3100 x 8 mm

Hydraulic workshop press PREMIUM WPMEH 30/2 Demonstration article Condition: slight signs of wear --> paint defects/scratches Standard equipment - Overload safety valve - Press pressure gauge - Switching valve up / down - Cylinder piston chrome-plated - Press table with stake-out bolt - Operating instructions / CE Specifications: Pressing capacity max. 30 tons Electro-hydraulic drive Two drive speeds Manual Hand Pump Press table chain (height adjustment) Oil flow stage 1/2 2.82 / 11.84 l/min Piston speed level 1/2 9.8 / 3.57 mm/s Return speed 18.11 mm/s Motor power 1500 W Mains connection 400/50 V/Hz Machine height 2120 mm Machine length without pump 1000 mm Machine width 695 mm Inlet length 750 mm Strap width 260 mm Inlet height max. 950 mm Machine length with pump 1315 mm Machine width with pump 805 mm Piston stroke 380 mm Weight 385 kg Subjec ...

a hydraulic single-stand drawing press Müller model CLZ.100.1.34, Y.O.M. 1994, good condition, with UVV, Siemens S7 screen control, throat gap 400 mm, installation height 800 mm, table surface 800 x 730 mm, stroke 600 mm, drawing cushion 40 to., drawing cushion stroke 200 mm.

Key data: 3 t, 150 mm

For sale in new condition HYUNDAE CETTA HHP-3 hydraulic press "more pieces" manufacturer: HYUNDAE "Korea" type: HHP-3 year of manufacture: 2018 load range: 1-3 tons Stroke [mm] 150 open height: 250 mm -safety light gate -two-handed operation .-mobile work table Hyundae press control Pressing rod closing speed: 178mm/sec Pressing rod pressing speed: 54mm/sec Opening speed 79 mm/s Table size: 450x360mm Max. Working pressure: 60kg·f/㎠ Hydraulic motor 1,5 kW 3 phase/4P 200v Weight: 350kg machine height "without table": 1415mm machine length: 950mm machine width: ca 700mm working table with casters or level bolts

Furnace 1200 temperature 10 - 1200 Celsius 2 heating zones 100kW auto door PLC Poreba Gurutzpe Tacchi Geminis Tos Amutio cazeneuve Skoda Morando Niles Colchester Heyligenstaedt Kramatorsk Mondiale Safop Cazeneuve Alzmetall mas stankoimport csepel carlton kolb soraluce bergonzi flott Erfurt Weingarten smeral schuler ebu mueller zts kosice wlochy minster Stanko stankoimport glaser huta zygmunt aft donaldson eumuko Elblag Engel Demag Arburg Krauss Maffei Battenfeld Manesty Mazak Voronezh Trumpf Amada Cincinnati Netstal Rose Forgrove Illig Foremost Nissei Sandretto Fette Mazak Mori seiki Haas Okuma Gildemeister Doosan Daewoo traub hwacheon index Wema zeulenroda mueller Erfurt tox presso technik dunkes galdabini hare ponar zeulenrdoda eitel Ziel des Spannungsarmglühens ist die Reduzierung von Eigenspannungen im Material. Solche Spannungen entstehen zum Beispiel durch Gefügeum ...

pressure: 160 t chamfer lenght: 4000 mm distance between columns: 3060 mm control: FORTRON CNC 10 H 4 throat: 280 mm stroke: 250 mm dayligth: 500 mm table length: 4050 mm table width: 280 mm feed down: 70 mm/sec feed up: 68,4 mm/sec working feed: 9 / 3,5 mm/sec operating pressure: max. 205 bar oil volume: 400 l total power requirement: 19,5 kW weight of the machine ca.: 20,8 t Total weight including accessories: 22 t dimensions of machine L x W x H: 4,8 x 1,88 x 2,93 m dimensions of switch cabinet: 1,6 x 0,5 x 2,25 m Acc.: programmable back gauge, upper and lower dies, table extensions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t chamfer lenght: 3000 mm distance between columns: 2560 mm dayligth: 450 mm throat: 450 mm adjustment of stroke: 240 mm horn length over column outer edge each: 175 mm table length: 3050 mm table width: 280 mm table height over floor: 820 mm electrics - voltage/frequency: 220/50 V/Hz control: CYBELEC, DNC60 stroke: 250 mm operating pressure: 150 bar total power requirement: kW weight of the machine ca.: 15 t dimensions of the machine ca.: L:4,0 x B:3,2 x H:3,44 m • hydraulical press brake, • new control CYBELEC DNC60 (in 2005), • lower part of the machine moves down 500 mm to the floor, at the moment the machine is mounted on a double-T-support, • prism and upper part of the machine in 3000 mm length The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 300 t chamfer lenght: 3050 mm distance between columns: . mm Control: Cybeleg type: DNC880S total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 320 t throat: 800 mm stroke: 630 mm distance between table / ram: max. 1000 mm ram head dimension: 710 x 600 mm table-size: 800 x 1200 mm work height max.: 1015 mm quantity of oil: 1100 l Number of working hours: 7663 h weight of the machine ca.: 15 t dimensions: ca. 1600 x 2200 x 4800 mm dimensions of switch cabinet: ca. 1200 x 400 x 1800 mm Tested for function. During the test run it is noticed that the press ram not 100% leak-proof. In addition, the cable for manual operation was mended several times. Upper cover is missing, since this was dismantled by the customer due to crane use. Operating instructions and electrical plans available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 1500 kN chamfer lenght: 3550 mm distance between columns: 3044 mm Control: Cybelec 34 PS-CN column arm: 350 mm max. ram stroke: 220 mm dimensions of the machine ca.: 3200 x 4200 x 2100 m sheet support: hinten / back number of support arms: 2, verschiebbar / adjust. die shift: hydraulical tool clamping: upper tool quick change system: crown: 3 sets of tools included The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 2000 /1000 t distance between columns: 2650 mm stroke: 500 mm column travel -side: 500 x 1000 mm diameter of piston: 710 mm number of pistons: 2 distance between table / ram: 1000 mm operating pressure: 130 / 230 bar dayligth: 800 mm table length: 2500 mm table width: 1600 mm table height: 250 mm draw back pressure: 500 kN number of T-slots: 8 turning speeds: 1500 U/min rapid speed: 120 - 140 mm/min closing speed: max. 120 - 140 mm/sec. hydraulical ram locking: return of plunger by small single cylinders: 100 - 110 mm/sec cutting sound absorber: 300 t die cushion capacity: 200 t die cushion stroke: 250 mm speed of die cushion: 100 mm/sec voltage: 380 V frequency: 50 Hz quantity of oil: 2000 l total power requirement: 93 kW weight of the machine ca.: 90 t dimensions of the machine ca.: 5000 x 2500 x 7200 mm transport measurements: ca. 6500 x 3750 x 2190 mm 1991 assembly of a di ...

Key data: 200 t, 500 mm, 200 mm

(1982) 200t Lauffer Hydraulic Press High-Speed Hydraulic Press with Advanced Shock Absorption This Lauffer hydraulic press is a high-performance machine designed for speed and precision, capable of 2,000 kN of pressing force. Its high-speed designation is backed by a rapid descent speed of 330 mm/sec and a sophisticated 8-fold flat guidance system to maintain ram alignment even under heavy or off-center loads. Technical Details Machine Type: Hydraulic Press Manufacturer: Lauffer Model: RPS 200 Year of Manufacture: 1982 Nominal Force: 200t Max. Return Force: 225 kN Max. Ram Stroke: 200 mm Shut Height: 500 mm Ram Guidance: 8-fold flat guidance Table & Ram Surface Area (W x D): 800 mm x 630 mm Table Hole Diameter: 204 mm Clearance Between Uprights (Front / Side): 840 mm / 320 mm Operating Speeds: Rapid Descent: 0 – 330 mm/sec (steplessly adjustable) Pre ...

Key data: 250 t, 500 mm

(2018) 250t Hidroliksan Hydraulic Press Hydraulic Press with Integrated Die Cushion for Deep Drawing This 2018 hydraulic double-column press is a heavy-duty production unit designed for versatility, featuring a robust 250-ton capacity and high-quality Rexroth and SICK components. With its 100-ton integrated die cushion and generous 500 mm stroke, it is exceptionally well-suited for complex deep drawing and forming operations that require precise pressure control. Technical Details ‍ Machine Type: Hydraulic Double-Column Press Manufacturer: Hidroliksan Model: H-TYPE Nominal Force: 250t Return Force: 50t Stroke Length: 500 mm Speeds: Approach: 160 mm/sec Pressing: 5 – 15 mm/sec Return: 190 mm/sec Working Surfaces: Ram Plate: 1,000 x 800 mm Table Plate: 1,000 x 800 x 100 mm Components: Pump: REXROTH (71cc – 103 L/min) Motor: 22 kW (30 hp), 1,500 rpm ...

Nominal force 100 t Stroke - 250 mm motor 3 kW more info on request

pressure: 160 t stroke: 400 mm table surface area: 1100 x 635 mm pressing speed: 6,57 mm/sec return speed: 11,62 mm/sec oil pressure max. in the work cylinder: 412 bar oil volume: 40 l dia. of piston: 145 mm column daylight: 1120 mm voltage: 400 V / 50 Hz dist. between pillars (front to rear): 350 mm total power requirement: 5,5 kW weight of the machine ca.: 1,2 t dimensions of the machine ca.: 1,7 x 0,9 x 2,1 m • unused workshop press, • manual and hydraulical operation, • horizontally moveable pressure cylinder, • working table hydraulical adjustable in height, • cylinder Ø 220 mm, piston base Ø 145 mm. • 2 support prisms • CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

DIEFFENBACHER PO-F 1250 A hydraulic press was built in Germany in 1981 by J. Dieffenbacher GmbH & Co. The machine was regularly maintained and upgraded throughout its service life. In 2016, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The piston seals were also replaced and measuring scales were added for precise position measurement of the slider, top ejector and lower die cushion. The DIEFFENBACHER PO-F 1250 A is an extremely versatile hydraulic press for demanding metal forming applications. Its main purpose is die stamping of steel components, calibration of forgings, dogging, hot and cold forging, cold forming and other operations that require very high press forces. All these machining processes are performed with a high press force of up to 1250 tonn ...

DIEFFENBACHER PO 500A hydraulic press was built in 1978 in Germany by J. Dieffenbacher GmbH & Co. The machine has been regularly maintained and upgraded throughout its service life. In 2017, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The seals and electrical system were also replaced. The DIEFFENBACHER PO 500A is the perfect choice for even the most demanding metal forming operations. It enables the execution of such operations as die stamping, punching, calibration of forgings and hot and cold bending. All these machining processes are performed with a high press force of up to 500 tonnes, which, combined with a highly dynamic slider, guarantees the best machining results. The machine is also characterised by a rigid body made of thick steel plates and a ...

SMG DS 40 hydraulic press was built in 2000 in Germany by SMG Süddeutsche Maschinenbau GmbH. The machine, which is characterised by high reliability, is used in metal stamping and punching. The machining process is performed with a high press force of 40 tonnes, which, combined with a rigid body, ensures the manufacture of highly repeatable and perfectly precise parts. The parameters, i.e. the ram speed, the position of the work tables and the press force, are adjusted by means of a simple control based on limit switches. The SMG press weighs 4 tonnes. Technical specifications of the SMG DS 40 press - maximum press force (adjustable): 40 t - work table dimensions (L x W): 600 x 400 mm - stroke of upper working table: 150 mm - distance between work tables: 400 mm - dimensions (L x W x H): 1230 x 570 x 2500 mm - weight of the SMG DS40 machine: 4 t

Double column press with 200 T output, Idle speed 45 mm/sec Opening speed 60 mm/sec Starting press speed 9 mm/sec Table size 2000x600mm Plunger size 2000x600mm OIL temperature monitoring Manual lubrication Free positioning of the plunger ( adjustable via adjustable sensors ) PILZ photoelectric sensors 14.1 mm on front and back Circulatory oil cooling Pressure retaining valve 0 to 600 sec. Mechanical plunger protection at the upper breakpoint T-grooves according to DIN, and according to customer requirements Pressure adjustment from 40 T to 200 T (adjustable via rotary knob) Travel limitation optionally via pressure or position Set-up operation, single stroke ( adjustable via key switch ) Two-hand operation Construction, commissioning, instruction against separate calculation Design Press design double column press Therma ...

Construction: Entirely constructed of stainless steel Press is used for tenderizing red and white meats without weight loss. All juices are retained inside the meat even after processing. The machine is fast and efficient, with a productivity of 500 steaks per hour. The thickness of the processed meat can be infinitely adjusted in the range from 1 to 30 mm. Technical data: Motor 1.5 kW Height 850 mm Width 440 mM Length 800 mm

Hydraulic press

SPECIFICATIONS: Hydraulic press for bent elements Dimensions of the work table mm: 3000 x 1600 Number of pistons: 2 diameters Ø 200 mm Piston stroke mm: 1400 -Fence -Oil pump - 02 Steam outlet openings

Standard Equipment's Chrome Coated Cylinder Boiled Steel Body Pressure indicator Pressure Adjustment User guide 2 Years Warranty CE

Pressing force 1000 kN Table size 750 x 560 mm, diarrhoea opening 100 mm Installation height 800 mm, stroke 500 mm Projection 360 mm Bear size 530x400 mm, 2 T-slots Ram speed: down 200 mm/sec, up 400 mm/sec Connection load approx. 21 kW Incl. Feeder WE16 for 160 mm bandwidth Coil tray and straightening unit Fabr. OFFICE; Type CA200/R40-7, YOC 1994 Reel, loop control Two-hand operation Manuals

pressing pliers, crimping pliers, cable lug pliers, hydraulic crimping pliers -Manufacturer: Orsta, hydraulic pressing tongs -Use: for large cable lugs -Hydraulic connection: see photo -Dimensions: Ø 118 x 315 mm -Weight: 11.2 kg

Specifications: Capacity: 60 t Passage between stand: 820 mm Working area, max.: 820 x 300 mm Piston stroke: 400 mm Flow speed: 6.1 mm/s Return speed: 10 mm/s Motor power: 3 kW Width: 1460 mm Depth: 850 mm Height: 2400 mm Weight, approx.: 700 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design made of welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Specifications: Capacity: 100 t Passage between stand: 1010 mm Working area, max.: 1010 x 300 mm Piston stroke: 400 mm Flow speed: 7.12 mm/s Return speed: 13.42 mm/s Motor power: 4 kW Width: 1600 mm Depth: 850 mm Height: 2450 mm Weight, approx.: 1000 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Specifications: Capacity: 160 t Passage between stand: 1100 mm Working area, max.: 1100 x 350 mm Piston stroke: 400 mm Flow speed: 6.2 mm/s Return speed: 6.8 mm/s Motor power: 5.5 kW Width: 1640 mm Depth: 1000 mm Height: 2550 mm Weight, approx.: 1300 kg Equipment: - Laterally movable cylinder via rack, pinion and handwheel - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...