hydraulic nc press used for sale

Key data: 400 t, 800 mm

Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...

FEINTOOL GKP F 160 hydraulic press was built in Switzerland. The automatic fine blanking press combines several workpiece machining stages into one precise process and significantly saves time and effort. As a result of fine blanking, parts with a maximum thickness of 6 mm obtain a characteristic even surface and accurately defined edges that cannot be achieved with other machines. The FEINTOOL GKP-F hydraulic punching press features a robust, stable construction and a total force of 160 tonnes. Offered with the machine a sheet metal feeder with a maximum thickness of 6 mm and a width of 210 mm allows for completely automatic machining. The automatic punching press underwent extensive modernisation in 1999. The total weight of the GKP-F 160 press is 9000 kg. Technical data of the FEINTOOL GKP F 160 fine blanking press - maximum sheet metal thickness: 6 mm - maximum sheet metal wi ...

Hydraulic press 80 t of stable design and high press force was manufactured in 2021. The hydraulic vulcanising press enables efficient processing of rubber and thermosetting plastics in manual or automatic mode. Excellent parameters and two electrically heated heating plates with a length of 1200 mm and a width of 1200 mm make the hydraulic vulcanisation press for rubber ensure high efficiency of 48 tons per month during three-shift operation. Technical specifications of the rubber press - press force: 80 t - heating plate dimensions (L x W): 1200 x 1200 mm - electric heating - distance between heating plates: 800 mm - dimensions of shelves (L x W): 1400 x 1400 mm - operation modes: manual or automatic - full technical documentation - CE certificate

Hydraulic vulcanising press 80 t built in 2021 is distinguished by its stable construction and high press force. The hydraulic vulcanisation press for rubber is designed for the efficient processing of rubber and other thermosetting plastics using two electrically heated heating plates with a length of 1200 mm and a width of 1200 mm. The hydraulic press achieves a capacity of 48 tonnes per month when operating in a three-shift system. Technical specifications of the rubber press - maximum press force: 80 t - electric heating - heating plate dimensions (L x W): 1200 x 1200 mm - distance between heating plates: 800 mm - dimensions of shelves (L x W): 1400 x 1400 mm - operating mode: manual or automatic - full technical documentation - CE certificate

SMG DS 315-1500/1300 CNC hydraulic press was manufactured in 1984 in Germany. The machine, consisting of two interconnected stations, is used for pressing metal workpieces in manual, semi-automatic and automatic mode with a pressing force of up to 315 tonnes. All the machine’s machining parameters are set using a CNC control with a full-colour, touchscreen display. The press is equipped with a hydraulic and pneumatic sheet metal feeder, servo drives for feed rollers to set a very precise stroke of up to 0.1 mm, safety cages and workpiece feed and drop control sensors. The SMG 315 T machine underwent a complete overhaul in 2007, during which components such as pumps and safety installations were replaced. Technical data of the SMG DS 315-1500/1300 press - maximum press force: 315 t - working table dimensions (L x W): 1500 x 1300 mm - upper machine point (from the table): 750 mm ...

Key data: 63 t

EUROMET Y41-63T hydraulic press manufactured in 2007 is designed for machining metal sheets, sections and profiles. EUROMET Y41 63T hydraulic press has a monolithic structure resistant to any deformations, which, combined with the 63-ton press force, allows to achieve excellent precision and quality of machining both in medium and large series production. Technical parameters of EUROMET Y41-63T hydraulic press - maximum press force: 63 t - work table dimensions (L x W): 580 x 560 mm - piston rod speed (pressure): 10 mm/s - piston rod speed (return): 95 mm/s - piston rod speed (no load): 38 mm/s - piston rod stroke: 500 mm - maximum piston rod feed: 800 mm - power: 7.5 kW

PONAR ŻYWIEC PHM 160 D hydraulic press manufactured in Poland in 1990 is used for machining metal and processing plastics (e.g. polofen or melamine) or rubber. The machine characterised by its high reliability, performs precise machining with a force of 160 tonnes in manual mode as well as in semi-automatic or automatic mode, thanks to its being equipped with time relays. The gantry press is also equipped with, among others, a hydraulic ejector with a force of 60 tonnes and two temperature controllers for the upper and lower parts of the heating plate. The offered machine was purchased from the university and has never worked during typical production. The total weight of the machine is 4000 kg. Technical parameters of the PONAR ŻYWIEC PHM 160 D press - maximum pressing force: 160 t (1600 kN) - ejector force: 60 t (600 kN) - working table surface (L x W): 800 x 800 mm - pressing ...

FEINTOOL GKP F 100T fine blanking press was manufactured in Switzerland in 1974. The machine, distinguished by its robust, stable design, can perform several demanding machining steps in one precise process, saving time and labour. Workpieces with a maximum thickness of 6 mm thus achieve an extremely even surface and precisely defined edges that are impossible to achieve on other machines. The machining process can be fully automated when the FEINTOOL GKP F 100/160 hydraulic blanking press is retrofitted with a sheet metal feeder. The total weight of the machine is approximately 9 tonnes. Technical data of the FEINTOOL GKP F 100T hydraulic press - maximum workpiece thickness: 6 mm - maximum sheet metal width: 210 mm - total force including auxiliary functions: 160 t - shearing force: 100 t - hydraulic counterweight force (upper table): 1-40 t - hydraulic force of ring jaw (lower ...

Hydraulic press, two-column press, oil hydraulic press -Press force ram: 65 to -Hydraulic unit: max. 330 bar -Clamping table: 440 x 250 mm -Max. Insertion height: 295 mm -Max. Width: 300 mm -Max. Stroke: 220 mm -with safety cage -Max. Feed speed: 3 mm/sec -Retraction speed: 6 mm/sec -Dimensions: 1680/500/H2300 mm -Weight: 980 kg

Hydraulic drawing press make CAME Panasonic Matsushita type THB 120 x 100Model no 1882 year of construction 1996Max. Press force: 125 tRetraction force: 20 tCompressive force of the die cushion: 70 tRetraction force of the die cushion: 37 tOil pressure of the press: 210 barOil pressure of the die cushion: 140 barTable size: 1300 x 1000 mmPassage: 1600 x 1200 mmInstallation height: 1300 mmRam stroke: 900 mmOil filling: 1300 lRapid traverse from max.: 300 mm / sCylinder diameter: 224 mm + 2 x 112/80Cylinder Tissue Diameter: 310/180/310/250 mmWeight of the upper tool max.:2300 kgDrive power: 45 kWDrive Power Cushion: 22 kWDimensions L x W x H approx .: 4,000 x 3350 x 5400 mmWeight approx. 31 tWith- heated intermediate plate- Holding device- Photocell manufacturer SICK- Two-hand operation- UVV regulations according to 89/392 EEC- CE clampprevious use:Deep drawing of slit masks for the pictur ...

Used KLAUKE HK 12/2 EL / HK 25/2 EL Hydraulic pump press pliers Connection 400V 16A Press pliers Klauke PK 120 Pressing range up to 400mm² C-head with 42mm opening width For Series 13 Press Inserts Without pressing insert Good condition. Fully functional See pictures Original price complete approx. 7000.-Euro gross Viewing and pick-up possible Shipping Germany (without islands) 119,00 Euro including 19% VAT The goods can be viewed at the location 59379 Selm by appointment. Company Michael Bergau Tel. 0152/29500504 The price includes 19% VAT. You will receive an invoice with VAT shown. Payment: Payment by bank transfer before delivery of the goods. Or cash payment on collection.

Single stand - hydraulic press SCHULZ type SES 250 Masch.Nr. 04.86.3511/3 Year of construction 1986 Compressive force 25 ton. Retraction force 10 to radius 360 mm Table surface 600 x 720 mm Ram surface 500 x 500 mm Diarrhoea opening in the table 100 mm Clamping pin hole 40 mm Ram stroke 400 mm Installation height max. 600 mm Table height above corridor 935 / 775 mm Tank capacity Hydraulic 380 litres Drive power 7.5 kW Mains connection 380 volts, 50 Hz - Fixed stop adjustment in press cylinder 180 mm- SICK photoelectric sensor - 2-hand operation - Substructure made of 160 mm U-steel Space requirement L x W x H 1900 x 1300 x 3100 / 3260 mm Weight 3.6 ton. good condition; used

Description: • Perforated plate hydraulic press for chairs • Serial number 1227 • Table dimensions 1540 x 940 mm • Main table with 2 positionable hydraulic pressure cylinders • Lower table with 2 hydraulic pressure cylinders, table dimensions 500 x 500 mm • Hydraulic pump with motor of 1.10 KW-2850 rpm Approx. Onsite Dimension. (l x w x h): 1,660 x 1,250 x 900 mm, weight approx.: 400 kg

Hydraulic Press SCHULER HYDRAP 315 Manufacturer: SCHULER Model: HPDZb 3150-3000/1300 New in: 2001 Condition: Very good Technical details Press capacity: 315 T Table dimensions: 3 000 x 1 300 mm Min. die stamping dimensions: 2 000 x 866 mm Slide stroke: 800 mm Max. shut height: 1 300 mm Number of strokes per min (regulated): 13-46 Cusion capacity: 160 T Cusion stroke: 200 mm

Muller Press, hydraulic press force 1000 T, double action, table 2600 x 2250 mm 2 pcs available

2 column hydraulic press #5232 Press force: 200 t upper stroke: 500 mm lower stroke: 200 mm overall dimension: 1800x2200x3700 mm Power: 10 PS Weight: 8.4 t

pressure: 220 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 180 mm/sec return speed: 185 mm/sec work speed: 10,0 mm/sec work stroke: 275 mm dayligth: 550 mm oil volume: 300 ltr. table height: 900 mm voltage: 400 Volt back stop - adjustable: 800 mm table width: 160 mm total power requirement: 18,5 kW weight: 14.000 kg range L-W-H: 5150 x 2250 x 3000 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z ...

Hydraulic press 1500 tons. Clearance between the two side pistons = 1400 mm. Clearance between uprights = 400 mm. Vertical clearance between open boards 3200 mm. Moving table dimensions = 1700 x 1800 mm. Fixed table size = 1500 x 2000 mm. This press has been used to produce forks for forklift.

pressure: 30.0 t stroke: 190 mm table surface area: 170 x 695 mm dayligth: 1000 mm column travel between the guideways: 695 mm weight of the machine ca.: 280 kg dimensions of the machine ca.: 1300 x 600 x 2000 mm MADE IN ITALY Furnishing: - powerful workshop press for craft and repair businesses - manual-hydraulic workshop press - 2-way valve with automatic piston retraction - Two-stage descent speed - Height-adjustable support table - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single column - hydraulic press MAE type S63SZ SO Masch.Nr. 551277 Year of construction approx. 1977 Compressive force 63 ton. Projection 320 mm Table surface 850 x 630 mm Ram surface 1050 x 500 mm Ram stroke 500 mm Installation height max. approx. 730 mm Table height above corridor 970 mm Tank capacity Hydraulic 600 litres Drive power 15 kW Mains connection 380 Volt, 50 Hz - Hydraulic die cushion under the table with holes through the table top - 2-hand operation - Electric control cabinet damaged Space requirement L x W x H 2000 x 1200 x 3420 mm Weight approx. 5 ton. The machine is working, the control cabinet is mechanically damaged. During the test run, the machine reaches a pressing force of 50 tons, presumably a pressure relief valve flows off.; used

Dresan 11 hot plate hydraulic press. Four pistons and 6 kg/cm2, automatic opening with timer or manual opening using a lever. Includes thermal and hydraulic oil. Circulation pump and thermometer. It works perfectly and can be viewed at any time.

Single Stand - Hydraulic Press DUNKES Type HZT 2,5 Masch. Nr. H94-2558 Year of construction 1994 Compressive force 2,5 ton. Projection 180 mm Table surface 420 x 300 mm Diarrhoea opening in the table 60 x 185 mm Ram surface 40 mm Pine bore 20 mm Ram stroke 160 mm Installation height max. 250 mm rapid traverse Down 65 mm /sec. Rapid traverse upwards 160 mm/sec. Working speed 8.3 mm/sec. Table height above corridor 950 mm Hydraulic operating pressure 135 bar Tank capacity hydraulics approx. 100 litres Drive power 1.5 kW Mains connection 400 Volt, 50 Hz - Pressure and displacement cut-off - 2-hand operation on the machine - Stroke counter - UVV 11.064 VGB 7.n.5.2 (for manual insertion work) - 32047 read operating hours Space requirement L x W x H 1100 x 980 x 1950 mm Weight 700 kg very good condition; used

pressure: 80 t stroke: 250 mm table surface area: 1040 x 260 mm column travel between the guideways: 1040 mm ajustment speed: 8,0 mm/sec working feed: 5,0 mm/sec return speed: 10,0 mm/sec engine output: 5,5 kW weight of the machine ca.: 835 kg. dimensions of the machine ca.: 1810 x 700 x 2100 mm Furnishing: - Robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed - Piston can be stopped in any position - Hydraulic tank mounted on the ...

pressure: 60 t stroke: 250 mm table surface area: 1040 x 370 (315) mm column travel between the guideways: 1040 mm ajustment speed: 8,0 mm/sec working feed: 4,0 mm/sec return speed: 10,0 mm/sec engine output: 4,0 kW weight of the machine ca.: 800 kg. dimensions of the machine ca.: 1.700 x 700 x 2.100 mm Furnishing: - Robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed - Piston can be stopped in any position - Hydraulic tank mounte ...

HYDRAULIC PRESS Manufacturer: JOOS Type: HP 90 Shelf size : 2550x1350 Hydraulic, electric Teflon shelves Elkom 6 actuators

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 70500 € : 1417.05 € : 40 to : 2050 mm : Y1 / Y2 / X und R Achse : 200 mm : 1700 mm : 350 mm : 440 mm : servomotorischer Spindela : 180 mm/s : 10 mm/s : 115 mm/s : 650 mm : 250 mm : 1000 mm : 7.2 kW : 2600 mm : 1450 mm : 2650 mm : 4400 kg STANDARD EQUIPTMENT: servomotorized spindle drive 4 axes (Y1, Y2, X and R) Color graphics controlDELEM DA-66T - 17 ", Touchscreen - 3D imaging in simulation and production - Suitable for personal Windows applications - Compatible with DelemModusys - USB and peripheral interface - Skill-specific application treatment - Sensor, bending and correction interface servo motorized back gauge on linear guides and ball screws CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guid ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 68200 € : 1370.82 € : 40 to : 1250 mm : Y1 / Y2 / X und R Achse : 200 mm : 1050 mm : 250 mm : 440 mm : servomotorischer Spindela : 115 mm/s : 10 mm/s : 115 mm/s : 650 mm : 250 mm : 1000 mm : 7.2 kW : 1950 mm : 1450 mm : 2650 mm : 3600 kg STANDARD EQUIPTMENT: servomotorized spindle drive 4 axes (Y1, Y2, X and R) Color graphics controlDELEM DA-66T - 17 ", Touchscreen - 3D imaging in simulation and production - Suitable for personal Windows applications - Compatible with DelemModusys - USB and peripheral interface - Skill-specific application treatment - Sensor, bending and correction interface servo motorized back gauge on linear guides and ball screws CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guid ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 107600 € : 2141.24 € : 135 to : 3050 mm : 4 : 320 mm : 3340 mm : 500 mm : servomotorischer Riemenan : 100 mm/s : 10 mm/s : 100 mm/s : 650 mm : 250 mm : 4200 mm : 2200 mm : 2550 mm : 7300 kg servomotor drive with multiple switched flat belt system 4 axes (Y1, Y2,X, R) CNC control DELEM DA-66T - 2D touchscreen display 17 - 3D visualisation in simulation and production - intuitive touch-screen control (simple drawing of the bending outline with your finger) - simple and convenient data transfer - multi-simulation option - user friendly programming in dialogue form - graphic simulation of the bending sequence servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) safety device BLVT light guard ...

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 96100 € : 1931.61 € : 80 to : 2550 mm : 4 : 320 mm : 2840 mm : 500 mm : servomotorischer Riemenan : 105 mm/s : 10 mm/s : 105 mm/s : 650 mm : 250 mm : 3700 mm : 2200 mm : 2550 mm : 6400 kg Electromotor drive with multiple switched flat belt system 4 axes (Y1, Y2,X, R) CNC control DELEM DA-66T - 2D touchscreen display 17 - 3D visualisation in simulation and production - intuitive touch-screen control (simple drawing of the bending outline with your finger) - simple and convenient data transfer - multi-simulation option - user friendly programming in dialogue form - graphic simulation of the bending sequence servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) safety device BLVT light guard ...

pressure: 100 t stroke: 310 mm table surface area: 340 x 1010 mm dayligth: 1055 mm working feed: 180 mm/min column travel between the guideways: 1010 mm total power requirement: 3.0 kW weight of the machine ca.: 1230 kg dimensions of the machine ca.: 1930 x 900 x 2360 mm MADE IN ITALY Furnishing: - powerful workshop presses for craft and repair businesses - with adjustable main cylinder - 2x speeds: (2-hand operation) 1,600 mm/min delivery speed 180mm/min. Working speed - electro-hydraulic press with pressure gauge - High speed hydraulic unit - Regulating and three-way valve: Forward-idle-reverse - Recording table, adjustable with screw-in lifting rod - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crate weight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm

Description: Hydraulic press for crimping hydraulic pipes, equipped with all the necessary matrices for pipes from 0.5 to 50 mm, never used 0 hours packed in wooden crate weight approx.: 310 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 1,000 x 1,400 mm

Used hydraulic press HK 7

Used hydraulic press PHW 12

We have for sale 4 pcs of Hydraulic Press 750 T single action table 3000 x 1900 mm Very good condition Under power

Laepple Hydraulic Press 750 T Single Action – Table 3000 x 1900mm Excellent condition 4 pcs available

Hydraulic Press 800 T Very good condition Under power

Hydraulic Press 1300 T force very good condition Under power

No. 4877: 1 gebr. Single-stand hydraulic press Fabr. EITEL, Type T 6.3, Bauj. 1973

Amada HFE 220-3 CNC Hydraulic Press Brake 220 Ton 3000 mm bending length 8 axis Machine is in good working condition Working hour : 17700 Tools are included

pressure: 200 t stroke: 300 mm table surface area: 1900 x 440 mm column travel between the guideways: 1900 mm working feed: 5,0 mm/sec engine output: 15,0 kW weight of the machine ca.: 4.800 kg. range L-W-H: 2.570 x 1.665 x 2.860 mm Furnishing: - hydraulic workshop press with adjustable cylinder - Table height adjustment - V-block tool insert - Pressure gauge The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Electro-hydraulic. Workshop Press Fabr. DAKO Best. -No: 2510Masch. -No: 1532 year 1977 / frame: homemadePower: 300 barHydraulic cylinder: 200 mm longDrive power: 0.5 kWPower connection: 220 V / 50 HzFrame:Installation height: 1000 mmPassage between the stands: 550 mmused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

EXNER EXSBR 200 hydraulic press YOM 8/1987 Serial No. 10042 Pressure 200 t Table 1800 x 800 mm Power requirement 65 kW Safety distance 195 mm Overtravel 52 mm Run-on time 120 ms Weight ca. 23 t

SPECIFICATIONS: Hydraulic hot press Dimensions of the work table mm: 3,000 x 1,300 Mounted serpentine table Maximum temperature: 120°. Number of pistons: 6 diameter Ø 65 mm Installed capacity KW: 30,5 Complete with intermediate plate Diathermal oil operation Complete with electric oil boiler

Hydraulic press for bent glued parts Tuma FP120 Сharacteristic Table size, mm - 1400х600 Maximum opening size, mm - 1000 Number of upper cylinders, pcs - 2 Number of side cylinders, pcs - 2 Diameter of cylinders, mm - 160 Working pressure, Bar - 180-190 Year of manufacture - 1989

pressure: 150 t stroke: 300 mm table surface area: 1070 x 290 mm column travel between the guideways: 1070 mm ajustment speed: 9,0 mm/sec working feed: 5,0 mm/sec return speed: 10,0 mm/sec engine output: 11,0 kW range L-W-H: 2200 x 1300 x 2300 mm weight of the machine ca.: 1870 kg. Furnishing: - hydraulic workshop press - Table height adjustment - V-block tool insert - Pressure gauge The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic press

SPECIFICATIONS: Hydraulic press for bent elements Dimensions of the work table mm: 2500 x 1300 Number of pistons: 4 diameter Ø 100 mm Piston stroke mm: 1500 -Enclosure -Control box -Oil pump - 2 steam outlets

SPECIFICATIONS: Hydraulic press for bent elements Dimensions of the work table mm: 3000 x 1600 Number of pistons: 2 diameters Ø 200 mm Piston stroke mm: 1400 -Fence -Oil pump - 02 Steam outlet openings