hydraulic motor used for sale

Equipped with: Tail lengths long 51 cm, upon collection the buyer gets the printout of real hours of 25 hours. four stroke, Electronic Fuel Injection, powertrim. Auction-ID: A1-42016-91

Equipped with: With remote control, with power trim, Smartcraft (readable hours around 450 hours) on delivery, the buyer will receive a printout with these hours. Long tail 51cm. 40 hp four-stroke outboard engine with EFI injection, long tail (20\"), electric start/trim, approx. 102 kg and max. 6000 rpm. Auction-ID: A1-42016-92

Equipped with 110cc engine Manual clutch; Kickstart Wheel/Rim: V: 90/100-14 (14\") A: 70/100-17 (17\") Hydraulic disc brake Oil shock absorber Single steel exhaust pipe Maximum speed: 70 km/h Unused in box Transport packaging: 1295 x 375 x 620 mm comes in box, unused Auction-ID: A1-40418-463

Permanent magnet motor, permanent magnet motor, electric motor, Perm.Magn-Mot, Perm Magnet Motors, servo motor, permanent magnet main drive motor, direct current motor, asynchronous main drive motor, spindle motor, permanent magnet - three-phase servo motor -Manufacturer: Indramat, permanent magnet - three-phase servo motor with brake -Type: MAC 093B-O-GS-2-C/110-A-2/ -Speed speed: nmax: 4000 rpm -Shaft: Ø 24 x 50 mm -Brake: 14 Nm 24 V -Dimensions: 395/140/H200 mm -Weight: 20 kg

Permanent magnet motor, permanent magnet motor, electric motor, Perm.Magn-Mot, Perm Magnet Motors, servo motor, permanent magnet main drive motor, direct current motor, asynchronous main drive motor, spindle motor, permanent magnet - three-phase servo motor -Manufacturer: Indramat, permanent magnet - three-phase servo motor with brake -Type: MAC 093B-O-GS-2-C/110-A-2/ -Speed speed: nmax: 4000 rpm -Shaft: Ø 24 x 50 mm -Brake: 14 Nm 24 V -Dimensions: 395/140/H200 mm -Weight: 20 kg

The mileage and other data given are to be understood as non-binding guideline values. No guarantee is given for the correctness of the information ; This lot has not been tested for functionality. Parts may be damaged or missing. The seller does not assume any warranty for road and operational safety; Battery dead; Auction-ID: A1-46596-1137

Max. bending length: 2040 mm, Sheet thickness: steel 2.5 mm, Alu 4mm, Stainless steel 1.5mm, with backgauge and foot pedal Auction-ID: A7-46619-260

Pallet with various accessories - 3x motors Vise Auction-ID: A1-46607-115

Technical details Type: Belt conveyor Configuration: Horizontal transport conveyor Drive: Electric motor with worm gearbox (marked VF 72”) Power: Estimated 0.37–1.1 kW Operation: Fixed speed (no inverter visible) Control: Basic electrical control box (on/off) Structure: Steel frame mounted on wheels Belt: Rubber/slat conveyor belt Application: Transport of metal parts, components, or bulk items between machines Equipment - Geared motor unit - Worm gearbox (VF 72 type) - Conveyor belt system - Mobile steel frame - Electrical control box Dimensions and weight (approx.) Length: 3000 mm Width: 600 mm Height: 900 mm Weight: 200 kg Auction-ID: A7-46498-87

Technical details Type: Industrial electric motors and components (mixed lot) Configuration: Assorted motors and drive components in transport cage Quantity: Approx. 6–8 electric motors Motor types: Asynchronous AC motors (various sizes) Power range: Estimated 0.5 kW – 7.5 kW Mounting: Mixed (foot-mounted and flange-mounted) Design features: - Cooling fin housings - Shaft outputs (various diameters) - Electrical terminal boxes Additional components: - Possible gear motor units - Pump or blower motor assemblies - Loose wiring, connectors, and accessories Application: Industrial drives for pumps, conveyors, fans, and general machinery Condition: Used, dusty, partially oxidized; untested; some units incomplete or with open terminals Dimensions and weight (approx.) Length: 1200 mm Width: 800 mm Height: 900 mm Weight: 300 kg Auction-ID: A7-46498-160

Technical details Manufacturer: KSB (Germany) Model: ARX F080-230 Type: Vertical single-stage submersible motor pump Year: 2024 Power: Approx. 5.5 kW Voltage: 400 V / 50 Hz Speed: Approx. 2900 rpm Protection: IP68 Insulation class: F Max fluid temperature: 40°C Configuration: Submersible design with integrated motor housing Connection: Flanged outlet Duty: Continuous industrial operation Application: Drainage, wastewater handling, process fluids Equipment - Integrated electric motor - Flanged discharge connection - Power cable - Mounting base / flange kit - Steel lifting cable (approx. 10 m) Dimensions and weight (approx.) Length: 800 mm Width: 300 mm Height: 350 mm Weight: 130 kg Auction-ID: A7-46498-99

Hydraulic power unit BOSCH REXROTH Year of construction approx. 1970Operating pressure Nominal capacity: 50 barOperating pressure: max. 70 barVolume flow: approx. 40 litres/min. Tank capacity: 240 litresEngine power: 4 kWNee connection: 380 volts, 50 Hz- 1x electric hydraulic valve BOSCHPlating requirement length: 1020 mm, width: 610 mm height: 1000 mmown weight: approx. 170 kg; used

Hydraulic power unit with hydraulic pump BOSCH REXROTHHydraulic power unit Year of construction approx. 2000Operating pressure pump1: 10 barVolume flow pump1: 24 litres/min. Engine power pump1: 1.5 kWoperating pressure pump2: 120 bar (max.140 bar)Volume flow pump2: 44 litres/min. Engine power pump2: 11 kWTankle capacity: 200 litresMains connection: 400 volts, 50 Hz- 2 independent hydraulic pumps, each with its own drive motor- 6 hydraulic valves built- Cleaning cover in the oil tankSpace requirement L x W x H 1000 x 700 x 1200Weight:

Hydraulic Power Unit, Hydraulic Power Unit BOSCH REXROTH Order No: 983885 Year of Manufacture 1982Tank Capacity: 150 LitresOperating Pressure: 60 bar Nominal Pressure / Max. 100 barVolume Flow: 20 Litres/min. Motor power pump : 3 kWNetz connection: 380 volts, 50 Hz.- 1 piece hydraulic pump BOSCH REXROTH, type 1PV2V3-40/25 RAO1MC63- 2 pieces hydraulic valve BOSCH REXROTH with electric solenoid coil, type E6 E51/AG24NZ4- 2 pieces hydraulic valve BOSCH REXROTH with electric solenoid coil, type 4WE10D10OFLG24NZ4- 1 piece pressure accumulator- various throttle valves, pressure regulators and

Hydraulic power unit with hydraulic pump BOSCH REXROTH / HYDRONORMAHydraulic power unit Year of construction approx. 1985Operating pressure: max. 65 barVolume flow: 20 litres/min. Fuel tank capacity: 110 litersEngine power: 3 kWMortor speed: 1440 rpm. Mains connection: 400 volts, 50 Hz- 1 piece hydraulic vane pump MANNESMANN REXROTH, type 1PV2V3-40/25RA01MC63A1- 1 piece drive motor KATT, type FFN 100L- 1 piece pressure reducing valve BOSCH REXROTH, type DR 8 G433/100 YM- 1 piece return filter- 1 piece 4/2-way hand valve (e.g. for retracting and extending a double

Hydraulic power unit with hydraulic pump RACINE / VICKERSHydraulik gensetOperating pressure: max. 44 barVolume flow: 13 litres/min. Tank capacity: 40 litersEngine speed: 950 rpm. Engine power: 0.75 kWNetz connection: 380 Volt, 50 Hz- 1 piece hydraulic vane pump PVQ-PSS=-06CR-J11- Hydraulic tank with maintenance cover and oil level sight glass- 2 pieces hydraulic hoses with 12L connections, length = 950 mmSpace requirement L x W x H:: 700 x 400 x 750 mmWeight: 97 kg (without oil content); used

Hydraulics Machine viseJaw width: 130 mmJaw height: 46 mmClamping force: 4 ton. Clamping range: 0 to 220 mmOpening width: max 223 mmGuideway height: 72 mm- 3 clamping ranges adjustable via plug-in pins, 0 to 79mm, 67 to 151 mm and 139 to 223 mmDimensions L x W x H: 535 x 210 x 119 mmWeight: 35 kgvery good condition; used

Hydraulic scissor lift table GRUSE type ELS 0.5-8-1-G-SOFabr. No: 124984 year of construction 2017Load capacity 300 kgPlatform size 1250 x 800 mmUsable stroke max. 785 mmOverall height - table bottom 345 mmOverall height - table top 1130 mmEngine power 0.8 kWNet connection 400 volts, 50 Hz- Foot switch for up and down, with emergency stop and key switch for control One- Single scissors with a lifting cylinder- Circumferential safety contact strip with limit switches under the upper frame- Adjustable limit switch for the upper stroke restriction-

table 500/600 mm

Hydraulic

AMOB MAH 60/3 Section: 20 cm ³ Power: 5.5 kW - 7 hp Rpm: 11 rpm Ø instrument: 170/108 mm Ø shaft: 55/55 mm Weight: 600 kg Dimensions: 1300x890x1550 mm Nr. 3 motorized rollers hydraulic adjustment top roller Side guide rollers Programmable and displayed top roller Horizontal and vertical working position Pedal with safety device start/stop General information: The AMOB MAH series top roll profile hydraulic bending machines are the backbone of the widest selection of profile curves in the world. The MAH series is perfect for those applications that require multiple passes, where repeatability is paramount. Motorized 3-roller machines are suitable for narrower spokes and minimize material marking. Both horizontal and vertical working positions ensure that, even in the smallest workspaces, a mah series profiling machine will be placed. T ...

Hydraulic pump 250 BAR 1, 1kW three phase motor, 3ccm/& 8 l container with valves and tray, ready for use. Info under 0170 / 2204056 Mail to fa.raupp@t-online

Sell used hydraulic power units 5. 3 with 11 kW electric motor- 2 with 4 kW electric motor- Price per PCs. Motors from ASEA Sweden

SMG DS 315-1500/1300 CNC hydraulic press was manufactured in 1984 in Germany. The machine, consisting of two interconnected stations, is used for pressing metal workpieces in manual, semi-automatic and automatic mode with a pressing force of up to 315 tonnes. All the machine’s machining parameters are set using a CNC control with a full-colour, touchscreen display. The press is equipped with a hydraulic and pneumatic sheet metal feeder, servo drives for feed rollers to set a very precise stroke of up to 0.1 mm, safety cages and workpiece feed and drop control sensors. The SMG 315 T machine underwent a complete overhaul in 2007, during which components such as pumps and safety installations were replaced. Technical data of the SMG DS 315-1500/1300 press - maximum press force: 315 t - working table dimensions (L x W): 1500 x 1300 mm - upper machine point (from the table): 750 mm ...

Working width: 4100 mm sheet thickness: 16 mm projection: 300 mm rear gauge: 1500 mm power: 400 V, 45 kW space: 4800 x 3500 x 2600 mm weight: 28000 kg

Mapelli 300ton downstroke hydraulic presses with vacuum, Type T300, year 1990, 4 column type, with pneumatic front guard, fixed guards to sides and rear, main ram dia 450mm, with pull back rams, single daylight 500mm, with 600mm wide x 700mm electrically heated platens. With hydraulic power unit mounted on top. Complete with controls etc and in good condition.

Working width: 5050 mm thickness: 10 mm power: 30 kW space: 2450 x 5600 x 2500 mm weight: 28000 kg

Hydraulic unit incl. wiring diagram Manufacturer: Aros Hydraulik GmbH Type: HE160-Z21/V5, 5-VAD22/V5, 5-B3/120-LV6P-so. Engines: Manufacturer: Asea motor Type: MBT 132s Power: 5.5 kW Frequency: 3 ~ / 50 Hz Manufacturer: Dietz-motoren GmbH & co. KG Type: 4001540 441883 Power: 5.5 kW Voltage: 380 V Current strength: 11,8 A Valve block: Manufacturer: Lenze Type: 14 128 10 1 0 S 0 Pump: Manufacturer: Sauer / Daikin Type: J V15SA4CRX85 Maximum pressure: 250 bar Filter: Manufacturer: Argo filter Type: HD 046 056 Capacity: 35 l / min Pressure: 210 bar max. New price: approx. 7900

Working width: 4100 mm sheet thickness: 6 mm radius: 100 mm rear gauge: 0-1000 mm power: 18.5 kW space: 4600 x 2200 x 1950 mm weight: 11000 kg

VERTICAL PRESSURE: 2 x 315 T, HORIZONTAL PRESSURE: 2 x 200 T, VERTICAL STROKE - UPPER PISTON: 200 MM - BOTTOM PISTON: 150 MM, HORIZONTAL STROKE: 200 MM, OPERATION PRESSURE: 280 BAR,

Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h

Used hydraulic press PHW 12

Hydraulic cylinder filter press Chamber filter press New, used and refurbished Ask us.

Hydraulic radial engine manufacturer Calzoni MR. 3000-F1N1N2S2NX 0401 / 46528, 656592 250 bar Used Husky injection moulding machine, type GL225RS60/50

Hydraulic radial engine Manufacturer Denison/Calzoni Type MR300D - F1N1N2S2NX 0401 / 46529, 742056 250 bar Used from Husky injection moulding machine type GL225 RS60/50

1 x Wickert 500ton upstroke vacuum press, Type: WKP5000/5/3, Year of manufacture: 1997, Machine Number: 2885 with 500mm x 500mm electrically heated platens, sliding bottom platen with ejector table, Daylight: 340mm 400/690V, 50Hz, 22kW. Heaters 12.5kW, Pressure 300 Bar Fixed guarding to rear, SICK light curtain guards to the front. With Siemens S5 PLC controls. In very good condition.

used hydraulic unit with accumulator

Hydraulic rescue scissors operated with hydraulic pump (630bar) internal combustion engine. To be used as e.g. cable scissors for use in areas without power supply. 1 set with fuel-powered hydraulic unit 1 hydraulic scissors 1 hydraulic spreader All the goods in very good, ready-to-use condition. Special price

Hydraulic unit 250 l, 4 kW, max. 45 bar More: Hydro-aggregator FORTUNA Sperry Vickers, 200 l tank, with various valves pump: G-PA3-25-EK1-20R (see picture)

Hydraulic unit 360 l, 2 x 11 kW, 2 memory More: Hydro-aggregate REXROTH DB 250-04-0, 1 memory, various valves Hydro-aggregator REXROTH, 60 l tank, various valves (see pictures)

Hydraulic unit 160 l, approx. 4 kW, various valves etc.

Hydraulic agregate with Bob and cooling, engine made in Swden 55kW, cubic capacity 300 dm per min, pressure 31,5 MPa, transport weight ca. 800kg. Ready for work.

Maximum cutting length: 4000 mm Maximum sheet thickness: 4 mm steel Driven back gauge to 1000 mm Page fence and table extensions Cutting length limit Cutting edge lighting Protection fence, roll with safety switches Weight: 8500 kg

Manufacturer: Weinbrenner Type: TSV 6 / 3050 Year of constr.: End of 2015 demonstration machine Cutting length: 3050 mm Cutting capacity: 6 mm (steel) Hours of operation: 54 Control: Cybelec DNC 60 Dimensions L/W/H: 4100/2050/2100 mm Table height: 1000 mm Weight: 8500 kg Min. cutting angle: 1° Cutting angle max.: 2.5 ° Stroke rate minimum: 20 min. Max speed: 25 min. Cutting gap adjustment: motorized Cutting angle adjustment: hydraulic Number of holders: 14 Rear velocity range: 1000 mm Security: setting the photocell safety on the front and back Oil filling: 225 l Electrical power: 15 KW Power consumption: 3 x 400 V / 50 Hz Back-up fuse: 50 A Additional equipment: Extension of the side stop on 2050 mm Side stop side swing-away A total of 8 support arms freely movable along the entire length of the table The machine is a demonstration machine in mint cond ...

JJZ-CP type press designed for the production of plywood, doors, MDF. The glued elements are fed and removed from the press automatically by means of driven rollers. The press can be used with glue feeders. Specifications: -max. pressure 500T/ adjustable/ -max. load height 1300mm -max. batch size 1300x2500 -press size 3600x1370x4500 mm -press foundation ~500 mm below the floor level -feeding table 2000x1960 mm -receiving table 2350x2500 mm -max. power 13.2 kW -Ce -capacity of 6 batches per hour Currently, we glue panel doors and MDF board on presses. Very good technical condition. We offer a plywood production line dedicated to these presses.