127,247 used machines on RESALE, but how to find them? Machine Search
sheet width: 2100 mm plate thickness: 6,0 mm ST 42 thickness at Niro-steel: 4,0 mm VA cutting angle: 1,2 Grad no. of strokes: 28 Hub/min oil volume: 150 ltr. down holder: 11 Stück control: CYBELEC CybTouch engine output: 11,0 kW back stop - adjustable: 1.000 mm table height: 800 mm weight: 4.500 kg range L-W-H: 3.010 x 2.100 x 1.640 mm ------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment ------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws ...
pressure: 220 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 10.0 mm/sec return speed: 160 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 160 mm oil volume: 300 ltr. voltage: 400 Volt total power requirement: 18.5 kW weight: 13800 kg range L-W-H: 5150 x 2250 x 3000 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-58T graphics / touchscreen 2D graphic programming 15 high definition color TFT screen Bending sequence calculation Product programming and display in real size USB interface - Motorized backgauge with R-axis, on recirculating ball spindles - X ...
sheet width: 3100 mm plate thickness: 6,0 mm thickness at Niro-steel: 4,0 mm distance between columns: 3100 mm no. of strokes: 18 Hub/min down holder: 14 Stück oil volume: 150 ltr. cutting angle: 1,2 ° control: CYBELEC CybTouch total power requirement: 11,0 kW weight: 6300 kg range L-W-H: 4.000 x 2.100 x 1.640 mm -------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Ca ...
sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3.100 mm down holder: 14 Stück no. of strokes: 16 - 24 Hub/min oil volume: 150 ltr. cutting angle: 0,5 - 1,5 ° thickness at Niro-steel: 4,0 mm column arm: 350 mm engine output: 11,0 kW weight of the machine ca.: 7.060 kg range L-W-H: 4,1 x 2,2 x 2,19 m -------------------------------------------------- electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment -------------------------------------------------- Furnishing: - CNC guillotine guillotine shears - with electr. / hydr. Cutting gap and cutting angle adjustment - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including s ...
pressure: 320 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 140 mm/sec work speed: 10.5 mm/sec return speed: 150 mm/sec work stroke: 375 mm dayligth: 650 mm table height: 900 mm table width: 220 mm oil volume: 400 ltr. voltage: 400 Volt total power requirement: 30.0 kW weight: 22064 kg Dimensions (HxWxD): 5350 x 2450 x 3150 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot ...
Hydraulic guillotine: - 125 TN - Cutting size: 1600 mm wide x 1400 mm high - Hydraulic unit with engine: 30 hp (22 kW)
Key data: 3100 mm, 16 mm
- Year of construction 2001 Specifications - Cutting length: 3100 mm - Capacity: 16 mm - Stroke: 170 mm - Stroke rate: 10 /min - Oil tank: 410 l - Engine power: 37 kW - Operating voltage: 400 V - Rated current: 72 A - Rated current main fuse: 100 A - Dimensions WxHxD: 3750 x 2400 x 3425 mm - Weight: 13800 kg
Soenen CCH 3100 x 6 mm Cutting length: 3100 mm Max sheet thickness st 45: 6 mm Backgauge: no backgauge Electric motor (power): 15 HP Length: 3300 mm Depth: 2000 mm Height: 2000 mm Weight: 9,5 ton
gebr. hydr. Guillotine shears, Fabr. LVD, Type MVN 25 / 4, built in 1984 Capacity 2500 x 4 mm with backgauge with documentation Other accessories: - Conveyor table - Lift table
Offer 20223 Specifications: - Operation via handheld remote control with cable - Load capacity 1000 kg - Platform size 1250 x 800 mm -Min. Lift table height 280 mm -Max. Lift table height 950 mm - Stroke 670 mm - Hydr. drive 400 V / 1.1 kW - Space requirement approx. W 1300 x D 900 x H min. 280 mm - Weight approx. 150 kg - Mobile undercarriage
tank capacity: 200 l engine output: 5,5 5,5 current capacity: 380 V / 50 Hz total power requirement: 6 kW weight of the machine ca.: 800 Kg range L-W-H: 1,3 x 0,7 x 1,0 m Hydraulic center winders for knitted fabrics, adjustable, controllable tension, Menzel connection system. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25328 Specifications: - Max. cutting width 3200 mm - Max. cutting capacity at 45 Kp/mm² 12 mm - Stand projection 175 mm - Cutting angle 1.48 ° -one. Cutting gap adjustment - Number of hold-downs 13 pcs - Stroke rate up to 10 1/min - Front angle stop approx. 1100 mm - 2 pcs. front support arms approx. 1100 mm -Mot. Back gauge with positioning control up to 1000 mm - Rear space protection with light barrier - Cut line illumination - Working height 860 mm - E - Footswitch - Drive 400 V / 19.5 kW - Space requirement approx. W 4150 x H 2150 x D 2300 mm - Weight approx. 8.5 t
Pressing force: 4000kN, pressing pressure: 320bar, oil pressure: 250bar, blank holder force: 1600kN, blank holder stroke: 200mm, blank holder dimensions X/Y: 1000mm/800mm, blank holder ejector force: 160kN, ejector force: 63kN, ejector stroke: 100mm, overrun distance: 40mm, overrun time: 190ms. Documentation available. An on-site inspection is possible.
Kircheis 2100 x 3 mm Max worklength: 2100 mm Max tickness: 3 mm Length: 3250 mm Depth: 800 mm Hight : 2000 mm Weight: 2,5 ton
SLIDE total force (nominal): 880 to stroke: 305 mm cutting velocity min.: 5 mm/s cutting velocity max.: 70 mm/s closing velocity: 200 mm/s returning velocity: 200 mm/s V-RING nominal force: 400 to stroke: 40 mm COUNTER RAM nominal force: 200 to stroke: 40 mm TOOL DIMENSIONS lower table (left-right): 1010 mm lower table (front-back): 1600 mm upper table (left-right): 1000 mm upper table (front-back): 1000 mm shut height max.: 460 mm STRIP-FEEDER feeder type: roll feeder sheet width max.: 450 mm sheet thickness max.: 16 mm feeding step min.: 1 mm feeding step max.: 999.9 mm sheet length min: 3950 mm speed max.: 48 m/min Vertical adjustment: 140 mm nominal force: 60 kN ELECTRICAL SPECIFICATIONS total power consumption: 188 kW main drive power: 160 kW ATTACHMENTS -FINEBLANKING PRESS- a ...
Key data: 630 t, 275 mm
For sale is a used lowering press, manufacturer Sack + Kiesselbach, type EP 630. The machine is in very good condition. The press worked in an engraving company as a test press. Technical data: Pressing force: max. 630 tons. Installation height: max. 325 mm Stroke: max. 275 mm Weight: 4,000 kg
Offer 25376 Specifications: - Max. cutting width 3050 mm - Max. cutting capacity at 45 Kp/mm² 13 mm - Hydr. Cutting angle adjustment - Number of hold-downs 13 pcs - Front angle stop - 4 pieces of front support arms -Mot. Positioning-controlled backgauge 10 - 1000 mm - Cut line illumination - Rear space protection with side grilles + light barrier - E - Footswitch - Drive 400 V / 20 kW - Space requirement approx. W 4350 x H 2100 x D 2200 mm - Weight approx. 8.5 t
Inv. Num. : 8755 Type: M120Z Producer: Epsilon Generated: Parameters: The hydraulic arm is ready after it has been completely driven off.
Key data: 300 t, 800 mm
Hydraulic Press Emanuel 300 ton Year of construction: 1989 Dimension table: 1600 x 1300 mm Light max: 1130 mm Light min: 350 mm Slide stroke: 800 mm Cushion stroke: 400 mm Side upright clearance: 640 mm
Hydraulic Press Emanuel 500 ton press Year of construction: 1976 Dimension table: 2500 x 1900 mm Light max: 1490 mm Light min: 550 mm Slide stroke: 940 mm Cushion stroke: 400 mm Side upright clearance: 900 mm
Hydraulic Press MURARO 500 ton Year of construction: 2001 Dimension table: 2600 x 1600 mm Dimension lower table: 2700 x 1600 mm Light max: 1500 mm Light min: 700 mm Slide stroke: 900 mm Cushion stroke: 400 mm Side upright clearance: 770
1 set of hydraulic boars, Fabr. YALE Type HPS-2/ 2A, as good as new 2 stages; Operating pressure max. 700 bar
suitable for three-point mounting, 85 kg load capacity, Working width: 1
Inv. Num. : 948 Type: LVH 2500 Producer: ŽĎAS Created: 1961 Parameters: Depth: 1800 mm Width: 3450 mm Height above ground: 4650 mm Weight: 85 000 kg Voltage: 220 / 380 V Mains frequency: 50 Hz Workforce: 2500 t Number of strokes: 20/min Height of the lifts: 500 mm Minimum plunger distance from the table: 900 mm Maximum plunger distance from the table: 1400 mm Table surface: 1050 x 1400 mm Plunger area: 1050 x 1200mm
Pressing force: 3150kN, table dimensions X/Y: 2500mm/1600mm, stroke (fixed): 280mm, stroke rate: 20-80strokes/min, weight: approx. 68000kg. Including Dreher transfer and feed line. The control system is defective. Documentation available. An on-site inspection is possible.
feed pressure: bar liter capacity: l power capacity: kW total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Capacity 50 tons Stroke 750 mm Table size 1500x1000 mm
used
Safan 2500 x 3 mm Cutting length: 2500 mm Max sheet thickness st 45: 3 mm Max sheet thickness inox: 2 mm
Max. cutting length: 3050 mm Max. sheet thickness: 6 mm steel Controlled backgauge up to 1000 mm Side stop and table extensions Cut edge lighting Hydraulic shear angle adjustment Knife sharpened Weight approx. 6500 kg
Hydraulic cylinder, double-acting, 210bar, stroke 1500mm, D80mm, NS41191534.., Parker, mint condition Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition! The part was bought from a spare parts warehouse of a company, has never been in operation, is in a completely mint condition, but not in the original packaging. Parker double-acting hydraulic cylinder, Type: NS41191534/DDHMDRN24M-C1100, Overall dimensions: 1740x130x200mm, approx. 100kg, Stroke 1500mm, Piston D 80mm 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for direct and indirect consequential d ...
1 ALVE rimeless hydro extractor type LUH 1500, year 2017, basket diameter 1500 mm, basket height 800 mm, max. loading capacity 400 Kg, inverter controlled up to 750 rpm, 24 kW, 400 V, 50 Hz, electronic brake system, machine supplied with loading winch
Key data: 600 t
Max Tool length: 3000mm Max Tool Width: 2000mm Min Tool Height: 500mm Total Tool Weight: 20,000kg Max Closing Speed: 400 mm/sec
Key data: 3080 mm, 6 mm
max. sheet thickness steel (450N/mm²) 6.5 mm max. cutting width 3080 mm Machine weight 5600 kg Very good, ready-to-use condition
Haco TSX 3100 x 6 mm CNC Cutting length: 3100 mm Max sheet thickness st 45: 6 mm Strokes/min: 8 > 14 str/min Backgauge: 750 mm Adjustable cuttingedge: 0,5 > 3° Electric motor (power): 7,5 kW Length: 3880 mm Depth: 1650 mm Height: 1700 mm Weight: 4,5 ton Number of sheet holders: 18x
used
Darley 3100 x 8 mm Cutting length: 3100 mm Max sheet thickness st 45: 8 mm
Key data: 250 t, 100 mm
Heavy-duty cylinder with two-stage pump Type SB -2504 - RO Series 365 Pressure 250 ton
An oil-hydraulic press brake built in 1978 is offered, max. pressing force: 2000kN, max. stroke: 250mm, max. operating pressure: 295bar. Control panel defective. Viewing is possible by arrangement.
Offer 25500 Specifications: - Cutting length 3050 mm - Cutting thickness at 400 N/mm², strength 13 mm - Cutting thickness at 400 N/mm², strength up to 1000 mm, length 15 mm - Cutting angle 0.5 - 3 ° - Number of sheet hold-downs 18 pcs - Stroke rate 10 - 23 min -Mot. Back gauge up to 1000 mm - Rear area protection with light barrier - Front angle stop 1000 mm - HSLX version: - CNC control HACO SC 5 controller when entering the sheet thickness in mm -Auto. Cutting angle adjustment according to sheet thickness - Cutting length limitation -Auto. Positioning of the backgauge (8 programs – 80 sets) with - Digital display and autom. Backgauge retraction - Possibility of mot. Adjustment of the backgauge by 2 push buttons - Drive 400 V / 22 kW - E - Footswitch - Space requirement without support arms approx. W 4200 x H 2250 x D 2200 mm - Weight ...
Offer 25493 Specifications: - Cutting length 3050 mm - Cutting thickness at 400 N/mm², strength 13 mm - Cutting thickness at 400 N/mm², strength up to 1000 mm, length 15 mm - Cutting angle 0.5 - 3 ° - Number of sheet hold-downs 18 pcs - Stroke rate 10 - 23 min -Mot. Back gauge up to 1000 mm - Rear area protection with light barrier - Front angle stop 1000 mm - HSLX version: - CNC control HACO SC 5 controller when entering the sheet thickness in mm -Auto. Cutting angle adjustment according to sheet thickness - Cutting length limitation -Auto. Positioning of the backgauge (8 programs – 80 sets) with - Digital display and autom. Backgauge retraction - Possibility of mot. Adjustment of the backgauge by 2 push buttons - Drive 400 V / 22 kW - E - Footswitch - Space requirement without support arms approx. W 4200 x H 2250 x D 2200 mm - Weight ...
pressure: 1000 t distance between columns: - mm stroke: 200 mm total power requirement: 30 kW weight of the machine ca.: 8 t multiple images available The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic power unit REXROTH consisting of: Hydraulic tank 250 Ltr. Electric motor 15 kW REXROTH Internal Gear Pump HYDAC Accumulator SCHMÖLE Heat Exchangers Temperature monitoring Hydraulic filter Return filter
Pressing force: max. 630 tons. Installation height: 375 mm Stroke: 275 mm Weight: 4,500 kg.
Press force: 1,250 tons. Clear width: 585 mm Installation height: max. 480 mm Piston stroke: max. 355 mm Weight: 7,200 kg.
CONTROLS PLC SIEMENS S5 95U PRESS DESIGN drive system: hydraulic frame design: H-frame, monoblock openings in uprights: yes number of suspensions: 2 table cushion: yes PRESS FORCES total force (nominal): 650 to PRESS TABLE table surface (left-right): 3000 mm table surface (front-back): 1800 mm SLIDE slide force: 630 to table surface (left-right): 3000 mm table surface (front-back): 1800 mm stroke: 1000 mm SLIDE (HYDR. PRESS) approximation velocity max.: 200 mm/s working velocity min.: 7 mm/s working velocity max.: 15 mm/s return velocity max.: 120 mm/s return force: 65 to DIE CUSHION (TABLE CUSHION) cushion force: 250 to stroke: 400 mm cushion plate surface (left-right): 2500 mm cushion plate surface (front-back): 1450 mm working principle: hydraulical TOOL ASSEMBLY DIMENSIONS distance tab ...
Thermoforming press Jochnick & Norrmans 150/ton upper cylinder 100 Ton Lower Cylinder Table 1000x1000mm Built in 1973 New electrical cabinet in 1998 With light screen and wiring diagram Now in stock Price is freely loaded
RÖCHER conversion 1991 (formerly SCHÖN) Pressure capacity 1,600 kN Plunger stroke160 mm Table dimensions 850 x 650 mm Light barrier control next due exam February 26 Tenon clamp lock in the ram Express lowering speed 274 mm/s Working speed 20/10 mm/s Return speed 273 mm/s Drive power 30 kW Operating voltage 380 volts/50 Hz Fuse max. 100 A
CONTROLS PLC SIEMENS S5 95U PRESS DESIGN drive system: hydraulic openings in uprights: yes PRESS FORCES total force (nominal): 350 to PRESS TABLE table surface (left-right): 1600 mm table surface (front-back): 1400 mm SLIDE stroke: 1200 mm SLIDE (HYDR. PRESS) approximation velocity max.: 250 mm/s working velocity min.: 14 mm/s working velocity max.: 50 mm/s TOOL ASSEMBLY DIMENSIONS distance table - slide max.: 1250 mm distance between columns (H-frame): 1650 mm passline opening (free passage in side columns): 630 mm ELECTRICAL SPECIFICATIONS total power consumption: 60 kW DIMENSIONS / WEIGHTS height above floor level: 4300 mm height under floor level: 1000 mm total weight approx.: 24000 kg ATTACHMENTS (PRESSES) European CE standards: yes
pressure: 160 t chamfer lenght: 3000 mm distance between columns: 2650 mm Control: Cybelec DNC 800 total power requirement: kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
PRESS DESIGN drive system: hydraulic frame design: C-frame, single sided table cushion: yes opening in table: yes PRESS FORCES total force (nominal): 100 to PRESS TABLE table surface (left-right): 710 mm table surface (front-back): 560 mm SLIDE slide force: 100 to table surface (left-right): 560 mm table surface (front-back): 450 mm spigot hole diameter: 50 mm stroke: 320 mm thickness of bolster plate: 150 mm SLIDE (HYDR. PRESS) approximation velocity max.: 340 mm/s working velocity max.: 32 mm/s return velocity max.: 330 mm/s SLIDE EJECTOR / CUSHION nominal force: 2 to stroke: 40 mm DIE CUSHION (TABLE CUSHION) cushion force: 10 to stroke: 80 mm TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 455 mm STRIP-FEEDER feeder type: roll feeder sheet width max.: 300 mm sheet t ...
maximum number of results exceeded
please refine your search
