hydr pressbrake used for sale

Hydraulic unit, hydraulic pump, hydraulic pump, universal unit, hydraulic station, -Manufacturer: Rexroth Hydronorma, hydraulic unit -Hydraulic pump: Rexroth PV2V3-20/25R1MC 40 A1 -Motor: AEG 3 kW / 1420 rpm -Individual components: see photos -Hydraulic tank: tank capacity 120 l, with level indicator -Dimensions: 820/520/H880 mm -Weight: 232 kg

Hydraulic power unit, hydraulic pump, universal power unit, hydraulic station -Hydraulic power unit: with hydraulic reservoir -Aggregate: unfortunately without type designation -Hydraulic reservoir: Tank capacity approx. 7 l, with pressure gauge return line -Pressure: bar -Flow rate: l/min -Individual components: see photos -Dimensions: 350/240/H570 mm -Weight: 15.1 kg

Hydraulic unit, hydraulic pump, hydraulic pump, universal unit, hydraulic station -Manufacturer: Couperus Hydrauliek, hydraulic station made of slats/blind production -Housing: material VA -Motors: 5x elsto 1.5 kW -Pressure: up to 250 bar -Flow rate: 10 l/min -Individual components: see photos -Dimensions: 2100/660/H1040 mm -Weight: 554 kg

Hydraulic unit, hydraulic pump, hydraulic pump, universal unit, hydraulic station -Manufacturer: Couperus Hydrauliek, hydraulic station made of slats / blind production -Housing: material VA -Motors: 7x elsto 2.2 kW -Pressure: up to ca. 250 bar -Flow rate: ca. 10 l/min -Individual components: see photos -Dimensions: 3000/560/H1000 mm -Weight: 380 kg

Rear axle, steering axle, forklift axle, steering cylinder, hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, tilt cylinder, lifting cylinder, tie rod cylinder, tilt cylinder -Manufacturer: Weber Hydraulik, hydraulic cylinder tilt cylinder stroke 110 mm -Type: Clark 4334896 -Piston rod: Ø 35 mm / M30 -Dimensions: Ø 88 x 420 mm -Weight: 8.7 kg

Hydraulic power unit, hydraulic pump, universal power unit, hydraulic station -Manufacturer: Integral Hydraulik, hydraulic power unit with pressure switch -Pressure: up to 30 bar -Flow rate: 6 l/min -Pressure switch: Telemecanique XMG-B140 -Hydraulic reservoir: with pressure accumulator and level indicator -Individual components: see photos -Dimensions: 465/260/H510 mm -Weight: 48 kg

Bespoke built Hydraulic press for the manufacture of airplane seat back Force: 100 ton Table size 2000mm x 2000mm Platens drilled for oil heating Run out table Omron PLC Cylinder in need for repair, oil heater not included

Pressure: 16 tons Table dimensions: 800 mm x 410 mm Hammer dimensions: 350 mm Maximum stroke: 90 mm Motor power: 0.9 kW Weight: approx. 500 kg Machine dimensions: 800 mm x 900 mm x 1400 mm Very fast and powerful Two-hand operation for safe use Simple and intuitive operation Machine in perfect working order

Hydraulic Pump Variable Displacement Pump Manufacturer: Poclain Hydraulics Model No.: MSE18-2-D11-T19-2A50257EF The pump is NEW and fully functional. see pictures for more details.

pressure:400 t distance between columns:3250 mm distance table/ram, max. stroke up, adjustment up:1000 mm stroke:800 mm table surface area:3250 x 1400 mm table height over floor:1250 mm die cushion capacity:170 t die cushion stroke:200 mm die cushion area:1800 x 1000 mm distance between cutting impact cushioning:2610 mm side window:800 mm ram surface:3250 x 1400 mm return capacity:51 t speed down:300 mm/s speed up:300 mm/s working speed:16 - 33 mm/s quantity of oil:2900 l power requirement:100,0 kW weight:70,0 t Dimensions (WxDxH):4,9 x 3,1 x 7,6 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 cutting impact absorption:hydraulic

pressure:125 t distance between columns:2100 mm stroke:1000 mm Distance table/ram, max. stroke up, adjustment up:1300 mm Table area:2230 x 1300 mm die cushion pressure in table:63 t die cushion stroke in table:60 mm surface of drawing cushion:1000 x 900 mm table height above floor:1050 mm side window:1000 mm ram surface:2100 x 1000 mm speed down:50 mm/s speed up:50 mm/s working speed:10 mm/s oil volume:410 l height above floor:5,95 mm power requirement:22,0 kW Weight:31,0 t Dimensions (WxDxH):3,1 x 1,7 x 5,95 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table:hydraulic foundation pit:not necessary

pressure:200 t distance between columns:1400 mm stroke:300 mm distance table/ram, max. stroke up, adjustment up:500 mm table surface area:1300 x 1100 mm pressure of drawing cushion in table:80 t stroke of drawing cushion in table:150 mm die cushion area:700 x 700 mm capacity of ejector in ram:10 t ejector stroke in ram:50 mm table height over floor:930 mm side window:770 mm ram surface:1300 x 1100 mm speed down:400 mm/s speed up:410 mm/s working speed:20 - 50 mm/s return capacity:30 t oil volume:1350 l power requirement:70,0 kW weight:23,0 t dimensions (WxDxH):4,5 x 3,0 x 3,5 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table:hydraulic ejector in ram:hydraulic foundation pit:not necessary

Qty. 1 Second-hand extrusion press including (water-hydraulic system) Mfc.: Loewy - Hydropress USA Built: TBA Force: 12,000 UST Modernised: 2011 & 2014 (new PLC and control panels) Billet dia.: 14’’ – 26’’ (355.6 – 660.4 mm) Billet length: max. 65’’ (1651 mm) The press was used for the production of pipe up to 508 mm diameter and up to 50 mm wall thickness by the current owners. In 2011 the Press was partially rebuilt at which time all valves were rebuilt with new wear components, all brass was replaced for the container and rams and the loader table was rebuilt. In 2014 all new PLC Controls and the Control Pulpit were installed. Note: The water-hydraulic system is not included in the scope of supply due the system is also using for another extrusion press.

WEINIG HYDROMAT 22 BL Year of construction 1995 with splitting unit (lamellar saw) Feeding (Automatic feeder and pull-out unit!) With safety hood and soundproof cabin! Machine specifications:  - Planning capacity 220 x 120 mm  - Feeding, 8– 80 m/min, motor 18.5 kW Spindle layout:  Bottom-right-left Top - bottom, table rigid Bottom, table rigid, spindle prepared Top - bottom, table rigid, spindle prepared Gap unit, consisting of 1 right and 1 left spindle each 30 kW (4500 rpm) incl. table roll, sliding roller, spray barrier and gap wedge removal 4 roller pull-out Special pressure and fixtures for the production of top layer slats Feeder (all-in) for slats and pull-out tape     

Installation consisting of 2 lifting tables (in the form of a staircase) each with 1,500 kg load capacity, lifting height: 1.2 m each, incl. base for the higher lifting table (1.5 m high), hydraulic unit and control cabinet. Tables can also be used individually.

Hydraulic quick-stroke scissors, knife length 1000 mm, 2 pieces

16 stations, max. 12 mm , reel, ring straightener, Knoll scratch tape foerderer, various hoistand and spare parts

Feed sled unit hydraulic, detto

Feed slide unit hydraulic, for conversions or adaptations

Feed sled unit for 2 spindles, suitable for conversions or adaptations

Feed sled unit hydraulic, various spindles, for conversions or adaptations

Hi, I offer you Hydraulic power pack-three engines 90 KW each -oil tank 4500l, -Each engine drives two hydraulic pump gear -Pump Model 45V60A Power supply power to the extruder scrap shears in the set are three Dimensions chydrauliczne 160x190 coolers coolers 3 x -cooling connection 100 mm -power connection 80 mm Very Good Condition Net price: 59900 $-€14000 contact: + 48 600-517-834

FINLAY / TEREX 390 HydraScreen, screen / screening, Deutz engine, including additional belts, German Machine, 5.150 h, year 1996

GEKA HYDRACROP 55/S hydraulic ironworker machine built in 2008 in Spain, is a highly versatile and multifunctional machine that allows a wide range of workpiece machining. Its rigid, sturdy structure is equipped with 5 work stations, designed for the precise hole and corner punching, as well as shearing flat bars, angle bars and solid bars. Each work station is controlled by two hydraulic cylinders, which provide the possibility to work independently or in parallel on two stations simultaneously. The GEKA HYD 55/S ironworker machine weighs 1390 kg. Technical data of the GEKA HYDRACROP 55/S 2-cylinder ironworker machine General data - punching force: 55 t - cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - engine power: 5 kW - weight of machine: 1390 kg Flat bar shearing station - flat bar dimensions: 300 x 15 mm; 200 x 20 mm - blade leng ...

Roller spreader for rear mounting, drive via a 12 volt electric motor with overload protection (8 A). Container contents 120 ltr. , cam roller with interchangeable, asymetric cams (suitable for sand, salt and shards or granules)Roll width 125 cm, stirring shaft to prevent lump and bridge formation, low-wear 10-stage scattering volume regulation by adjustable spring bottom with rubber apron. With grating for accident protection and cable remote control (start/stop). Without growers! Scattering length salt approx. 5-6 km, sand approx. 1 km (manufacturer specifications) Built in 2012, unused, technically and visually as new condition, here and there paint somewhat repelled. Other roller spreaders, also trailers, self-loaders, drive hydraulic, PTO shaft or wheel stock. Winter service technology of all kinds, also slingshot spreaders, snow shields, snow blowers, tractors and used compon ...

Hydraulic rescue scissors operated with hydraulic pump (630bar) internal combustion engine. To be used as e.g. cable scissors for use in areas without power supply. 1 fuel-powered hydraulic unit 1 hydraulic scissors 1 hydraulic spreader Npjrx All the goods in very good, ready-to-use condition.

X axis travel 1000 mm Y axis travel 700 mm Spindle travel 300 mm Table dimension 1.100x842 mm Spindle speed 40-2000 rpm Max power input 10 kW Spindle motor 8 HP Total permissible load on worktable 1 ton Machine approximate weight 15 ton

pasteurizer for cream efficiency: 7500 l/h GEA plate heat exchanger valves and pumps : ALva Laval flow meters -Endress + Hauser Offer details and photos will be sent to the email.

Manufacturer: Reiplinger Hydraulische Pneumateische Stanze für Fensterbeschläge, Type: BSD-R6.6 SH-GR80, Model: inkl.Anschlaglineal ,

Manufacturer: Vickers hydraulikeinheit, Year: ca1990, FREETEXT1: mit Steuerblock, FREETEXT2: Vorratsbehälter 180 Liter, FREETEXT3: Pumpe, FREETEXT4: Kühler, FREETEXT5: die Maschine dazu wurde verschrottet, FREETEXT6: Motorleistung ca.4 kw, Year :ca1990

Hydraulic hammer / hydraulic-Meisel attachment used. For bobcat, mini excavator and small wheel loader with holder on fork carrier. Manufacturer/Type: unknown Holder approx. H-400 mm, W-1114 mm Meisel-A approx. 70 mm Meisel length approx. 400 mm Pressure: 400/850 PSI Total approx. 1160 x 1000 x 800 mm Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

Planing machine Weinig hydromat H30 W baujar 1990 36m/min Working width 300mm working-high 200mm memeeser of the fresspindel 50mm with suction