hot used for sale

The sale is intended for the entire brewery in the body, only and exclusively in the body. Steamed room from two 15hl semi automatic vats Ecobrewtech Touchscreen system control panel with recipe programming Very high precision electronic fiscal meter Cold (glycol) and hot (steam) storage tank of 30hl each. Double stage heat exchanger (cold water and direct glycol) 158hl cellar (2 45hl fermenters, 1 24hl fermenter, 1 29hl fermenter and 1 15hl fermenter) Steam generator year 2020 of 150kg / hour with pressure reducer (low pressure work but also high if necessary) Softener Chiller year 2020 from 23kw Manual 4-jaw isobaric bottling machine, July 2021 Cold room about 30sqm year 2020 Wheeled pump for washing year 2020 Product transfer tubes 2020 Skid 2 pumps for glycol and glycol tank 500lt 2 stainless steel control panels for fermenters control (total 10 slots, 7 active therm ...

Dishwasher / Quaker No. 1 (complete) - as in the picture: Manufacturer: TOPLINE Catalog number: E/473/O/2.12 Year of purchase: 2017 Quaker No. 2 (no bowl and rods) - to be completed or for spare parts Manufacturer: TOPLINE Catalog number: E/346/O/2.11 Year of purchase: 2012 The dishwasher performs a special washing process involving the action of hot steam from distilled water or nitric acid. Particularly useful in the laboratory using AAS, ICP and ICP-MS techniques for trace analysis. It allows you to wash glass, ceramic, Teflon (PTFE/PFA), quartz and borosilicate glass dishes. The heating element is a heater with a power of 1800 W. There is a tank on it, which is filled with water or nitric acid. The evaporating liquid is sent in the form of steam to the washed dishes through glass pipes. This steam can be reused after it has been liquefied. The entire device should be ...

Overview This brewery was built in 2017 by the Belgian manufacturer Coenco. The brewery equipment comes from a brewery that started its activities in 2017. Before the installation of the new brewing equipment, the brewery achieved an annual output of over 3000 hectoliters. Techn. Details 10hl Brewhouse Capacity: 1000l Copper cladded Brewhouse Dimensions (LxWxH): (4220 x 2500 x 3500) mm Execution: Semi-automatic (manual butterfly valves) Agitator in mash tank Cutting device in filter tank Wort buffer tank under filter tank: 1100l Whirlpool in mash / boiling tank Rotative cleaning balls Venturi system to condensate vapors Heating: super-heated water with electrical heating elements (72kW) Automation: Siemens S7 Product pump: Inoxpa SE20 or equivalent Hop filter to protect PHE Plate heat exchanger (PHE): Alfa Laval M3 –1500l/h Outlet PHE : DN25 Working platform : with sink 20hl Hot water  ...

Sumbel Präzicoat 500 banding machine; cleaned and tested; Working width 500mm; hot and cold glue; Speed adjustable. Gluing machine Sumbel Precision 500; cleaned and checked; working width 500mm; hot- and cold glue; adjustable in speed.

Horizontal fully automatic machine for 3-edge and 4-edge sealed pouches for filling and packaging powdery products in double pouch operation (with perforation): • Format range double bags (W x H) min. (2x50) x 260 mm, max. (2x80) x 260 mm • Output max. 100 double bags/min (depending on bag size) • Screw dosing SD 70/2 for double bags • Main dosing min. / max. 2.5 - 90 g per bag • Micro-dosing min. / max. 0.3 - 5 g • Max. Roll diam. 600 mm • Core diam. 76 mm • Max. Roll width 520 mm • Gluing table with splice detection • 2 pcs. Thermal transfer printer Allen Coding 5 line cliché, individually switchable • Longitudinal and cross seam hot sealing tool, head seam hot sealing tool • Sealing stations manually adjustable • Print mark control • Tear aid with a needle • Bag inflator • Bag opening control • Filling nozzle • Trickle protection by sheet shear  ...

Code: 0332 Brand: AMASPRES (ITALY) Model: 3000 Membrane press Working size: mm 3000 x 1300 Opening mm 500 Working height mm 250 Cover opening and closing with vertical pneumatic pistons This press is suitable for veneer of shaped pieces , such as window sash frames, curved pieces Upper heating with hot air Heating of lower side with hot air Consuption about 9 kwt Working cycle: about 10 min. Complete compressor for lifting of cover and under cover Processing prevacuum adjustable up to 6.5 atm The machine is equipped with time alarm, thermostat, thermometer, warning lights for calories and pumps Overall dimensions press mm 4100 x 1700 x 2050 h - Weight kg 1800 Overall dimensions depressor mm 1400 x 500 x 900 h - Weight kg 100

one used MEP Format S stirup bending machine • Single strand processing wire diameter cold drawn, hot rolled, smooth or ribbed wire from Ø 6 to Ø 12 mm from #2 to #4 fy = 600 N/mm² • Double strand processing wire diameter cold drawn, hot rolled, smooth or ribbed wire from Ø 6 to Ø 10 mm from #2 to #3 fy = 600 N/mm² – ft = 700 N/mm²

It is a used but durable hall construction which could also serve as a ball sports / football hall, equestrian sports hall and much more in the future. The steel frames are self-supporting and have a height of almost 11 meters in the ridge (in the middle). APPROXIMATE DIMENSIONS: Floor area: 2560 sqm built-up BG area; | Hall length: 65.50 m AK wall + boiler room; | Hall width: 39.09 m AK wall planking; | Eaves Height: 4.27m UK Roofing; | First - Height: 10.70 m OK Roofing; | Roof pitch: 18.75 degrees sym. gable roof; | STRUCTURE: Solid, articulated steel frame construction, with steel frames made of rolled sections mounted on point foundations or rails. The end frames or gable wall constructions are made of rolled profiles. Purlin line made of hot-rolled roof purlins. The 2 middle hall segments stand on rails so that the hall can be opened in good weather. FA ...

Gallus EM510S, 2005(10) Transaction Corona Web cleaning on both sides 10 Flexographic printing unit 2 Screen printing unit 10 ACTUAL UV Drying Systems 10 Hot air drying 10 Cooling Roller 2 Rotos Punches Longitudinal cutters Hot foils Cold foils Grid take-off Automatic register control Ionization Rail Free-standing take-up unit with double spindle Conveyor belt Printing Accessories Radiator

PreviousNext BRAND NEW GABLE TOP FILLING LINE FOR SALE Item #: Usm-195 Category Gable Top Machines Brand New Gable Top Filling Machine, Speed 3000 Pack Per Hour, Filling Volumes 200ml to 1000ml, Year of manufacturing 2023, Pack Type B 70x70, Cold and Hot both Filling Possible, UV Sterile System and Hydrogen Per Oxide Sterile and Alcholic Sterile. Suitable for Milk, juices, Cream and yogurt, Expiry Date Hot Stamping also instaled, Cap feeder, Lifter and Cap Applicator Also installed. Cap Applicator Made by Branson USA. Air Compressor also included, PLC Brand Inovance

SMERAL LZK 2500 Hot Forging press Fully refurbished in 2024 Capacity: 2500 Ton Speed: 65 SPM, continuous mode Ram/Slide Stroke: 320.00mm Ram/Slide Adjustment: 10.00mm Shut Height (Ram/Slide Down, Adjustment Up): 905.00mm Stroke of Upper Knockout: 50.00mm Stroke of Lower Knockout: 70.00mm Ram/Slide Width: 1320.00 mm Ram/Slide Height: 1100.00 mm Bed Width: 1340.00 mm Bed Depth: 1400.00 mm Power: 130kW Machine Length: 4055.00 mm Machine Width: 4000.00 mm Machine Height: 6710.00 mm Weight: 140000 kg Condition: like new refurbishing report: 1. Mechanical part • Complete disassembly of the press. • Measurement and troubleshooting of all parts. • The main parts of the press are tested (without destruction) in order to identify any defects. Frame: The frame was inspected and non-destructive testing of the most loaded areas was carried out. Damage to the table pl ...

Used Bottle Washing Machine KLINGER S16 2 90 speed 7000 BPH Model S 16 2 90 Year 1993 Production capacity 7 000 BPH with 2 L bottles Basket plastic with the possibility of washing bottles with max diameter of 95 mm Type of wash suitable for washing glass bottles through caustic baths Dimensions and weight L 9 x W 3 30 x H 3 05 m 19 000 kg Material stainless steel Description of the washing cycle 1st wash Capacity 45 L Maximum allowed operating temperature 150 C Maximum allowed operating pressure 5 bar 2nd wash Capacity 150 L Maximum allowed operating temperature 110 C Maximum allowed operating pressure 2 bar Technical data Nominal capacity 7000 BPH Range of control 4000 8000 BPH Total washing time 7 1 min Time of cycle 8 2 sec Scheduled execution time 16 min Bottles per row 16 Total rows 117 Housings 1600 Loaded rows 100 Preheating Total time 3 min Effective treatment time 2 6 min Sodium ...

Used Casepacking Monoblock Oma 2007 This machine is an OMA Monoblock composed of a case erector and case packer Oma brand case erector with hot glue closure Nordson glue heater Vertical cardboard formation Form 2 cartons of 6 or 1 of 12 with or without the hive inside Case packer with mechanical movement Possibility of forming and packing various carton formats Painted iron frame Accident prevention protections Production about 320 boxes of 12 and about 600 of 6 The machine is in accordance with CE 2007 with manuals In excellent condition Dimensions The machine is divided into 2 parts The first part forms and closes the bottom part of the cardboard with hot glue Front 2 500 mm Width 2 100mm Height 2 500mm Weight about 700 kg The second part for cartoning machine Front 2 000 mm Width 1 900mm Height 2 700mm Weight about 900 kg [...for more information send your inquiry to the seller.] refn ...

Cover Size: Max. 610x410mm, Format: Max. 400x270x40mm, Min. 120x100x3mm, Thickness: 3mm to 40mm, Speed: Max. 3.000 Cycles/Hour, 900-2500 Books/Hours, Cover Feeder With Scoring, Milling And Roughening Station, Hot-Melt Spine Gluing Unit, Hot-Melt Side Gluing Unit, Delivery

METOS PS528E Conveyor Oven Features: Hot air circulation technology Precise baking time and temperature control with microprocessor Fast baking time at low temperatures Temperature range: 100 - 287 °C Zone temperature adjustable with air control nozzles Oven chamber size: 713 x 480 x 95 mm Belt width: 457 mm, direction of travel can be changed Baking time adjustable: 3:00 - 30:00 Stainless steel construction Air control nozzles and belt easily removable Weight: 300 kg KEYWORDS: conveyor oven, pizza oven, Middleby Marshall Additional Information: The METOS PS528E conveyor oven is a high-performance oven that is ideal for pizzerias, bakeries, and other foodservice establishments. The oven features hot air circulation technology, which ensures even cooking and prevents food from drying out. The microprocessor controller provides precise baking time and temperature  ...

HYDRAULIC PRESS with hot platens model MANNI PMC 90/36 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton.90 opening mm.430 hydraulic pump motor power Hp 2 hot water plates heating via wood boiler weight kgs. 3800 volt. 380/50

HOT PRESS model SIMI 4LP second hand machine plates useful size mm. 2500 x 1300 n.04 pistons diam.mm. 80 max. thrust Ton. 60 specific pressure max. kg.2 / cm2 opening mm. 320 hot water plates heating via wood boiler (optional) weight kgs. 3000

Flash pasteurising to stabilise beverage quality. The product is heated via a plate heat exchanger and held at pasteurising temperature for a defined amount of time, after which it is then cooled down again., Additional title: Years of manufacture: 1993 - 2011, Capacity: 600 hl/h Beer with 6,0 g/l CO2, Hot water: 750 hl/h, Material: EPDM HT/NBR/1.4439; EPDM HT/1.4439, Features: Product plate heat exchanger; Water heater plate heat exchanger; Heat holder piping; Beer pump; Booster pump beer; Hot water pump; Measurement and control sensors

Etiquetadora Rollmatic 8500/h Self-adhesive rotary labeling machine PE LABELLERS Description Rotary roller feed labeling machine suitable for the application of wrapping labels from the reel. SHEET - Type: rotary labeling machine. - Application: label fed by plastic roll with hot melt glue. - Possible hot-melt combination + cold glue and / or self-adhesive on the same labeller. - Suitable for handling cylindrical and shaped containers (rectangular, square, oval, etc.), even empty. - Production 8,500 bottles / hour. Labeling Measures Width 3400 mm Height 2300 mm Length 3000 mm Measures Heat tunnel Width 1300 mm Height 2300 mm Length 5000 mm Features Model: ROLLMATIC Year: 2005 Width: 3400 mm Height: 3400 mm Large: 3000 mm

Very short used machine KT2 brand PENTA. (still under warranty) The heat-shrinkable tunnel of the KL series is heated to a temperature of 180/200 ° C. The KT tunnel series is powered by 380V 50Hz. A 3-phase socket must be used to connect the machine. It perfectly adapts to the needs of the given foil and the packaged object. This machine is a higher category. The tunnel ensures perfect and precise shrinkage, so the packaged product has a perfect appearance. In the conveyor, one roller is slightly bent, but this does not affect the function of the machine. (cosmetic defect) Shrinkage occurs due to the patented hot air flow system. The tunnel is equipped with a system of stainless steel dampers for adjusting the hot air flow. Tunnel description: Control panel Conveyor motor Tunnel fan Electrical cabinet Conveyor Tunnel curtains The length of the machine is 4.8 m and ...

Interplast GRAMEGNA brand that for over half a century has been operating on the heat-shrinking machinery market and is well known for the high quality and reliability of its machines. We sell our R-700 type shrink wrapping packaging machine. The equipment is in excellent condition. The machine has only been stored since the end of 2004. In 2004, we stopped producing soft drinks. We did not sell the machine because we planned to restart the activity. There are electrical drawings for it. Production capacity: nominal 20-25 packages actual 21-23 packets/min For 2 liter bottles, from the 4×2 format, according to a preliminary estimate, approx. 21 packages/minute. The machine consists of the following main units: 1 intro conveyor belt with bottle sorter for arranging bottles arriving in one row into several rows for bottles with round and square cross-sections 1 x Champion 4 HS- ...

Technical data: Sheet format max 740 x740 mm Sheet format min 100x120 mm Linear speed 150m/min Maximum capacity in bars- 36,000 bars/hour Compressed air connection 6 bar Net weight 1800 kg Dimensions L.-Sz-W-H. 5500 x1000x1400mm Depending on its mechanical properties, it can process paper and cardboard in the range of weights 100-600 g/m2 Gluing system HHS hot gluing system with 4 channel controller and 4 nozzles for glue application Standard equipment of the transport module and tool clamping system: - Transport module length 2750 mm - Omron SPS controller with 8 control channels - Interface for hot glue application system (Baumer-hhs) - Color touch screen - Pressure rollers 2 pcs with pull rollers, 2 pcs with 3 rollers, 6 pcs with 6 rollers, 4 pcs with 10 rollers, 2 pcs with 1 roller Standard tools: - 1 pc through-fracture / folding plate - One left and one  ...

Combustion chamber power: 49kW; Working power: 45kW; Particulate filter: Yes; Flue diameter: 180mm; Warm air delivery pipes: 2 x 200mm; Firebox length: 660mm; Firebox width: 480mm; Firebox height: 600mm; Air flow : 3500m³/h; Supply air filter: Yes, large-area supply air filter with no loss of performance; Power consumption: 550W; designed for room volume: 1000m³; Weight: 310 kg; Hot air furnace with a combustion chamber made of stainless thermal chrome steel, with reinforcing fins and flue exchanger. Centrifugal fans for the transport of hot air on special elastic suspensions, operating at low speed. Smoke fan, electrical switchboard and control panel with thermostat, 2 exhaust elbows.

Pressure washer, hot water pressure washer -Manufacturer: Kärcher, hot water high-pressure cleaner type 855 H -Connection: 230 volts -Power: 1.8 kW -Flow rate: 6.7 l/min 100 bar / max. 110 bar, 80°C -Burner: max. 25 kW -Dimensions: 630/380/H890 mm -Weight: 47 kg

Description: Max. edge thickness 30 mm Max. forward feed speed 20 m/min Pressure with rubber belt Panel support guides , with positioning by NC , NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit Constructor model : 08.376 automatic timed intervention , motor power : 3 KW r.p.m. : 12000 RPM Edge coil magazine glue pot for EVA hot melt glue premelter for EVA hot melt glue no. pressure roller 9 with positioning by NC , NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2 motor power : 1.85 KW r.p.m. : 11500 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 1 KW r.p.m. : 11500 RPM NO. EDGE PROCESSING UNITS 4 Processing Unit : Corner rounding no. motors : 2 with positioning by NC , motor  ...

Description: Max. panel height 60 mm Max. edge thickness 3 mm Pressure with rubber belt NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit Constructor model : RT20 motor power : 2 KW r.p.m. : 9000 RPM Edge coil magazine no. positions 6 Gluing system yes glue pot for EVA hot melt glue premelter for EVA hot melt glue no. pressure roller 3 No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming Constructor model : IT90 no. motors : 2 motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming Constructor model : RS10 no. motors : 2 motor power : 0.75 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : fine trimming to trim and round Constructor model : RF10 no. motors : 2 motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 4 Processing Unit : edge scraping Constr ...

Description: Max. panel height 60 mm Max. edge thickness 3 mm Max. forward feed speed 24 m/min Top pressure , NO. PANEL SIZING / MILLING UNITS , Unit : pre-milling unit Constructor model : RT20 automatic timed intervention : , motor power : 2 KW r.p.m. : 9000 RPM Edge coil magazine , no. positions 6 glue pot for EVA hot melt glue , premelter for EVA hot melt glue , Roller set to press the edge , NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming Constructor model : IT90 no. motors : 2 motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming Constructor model : RS10 no. motors : 2 motor power : 0.75 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : fine trimming to trim and round Constructor model : RF10 no. motors : 2 motor power : 0.37 KW r.p.m. : 12000 RPM NO. EDGE PROCESSI ...

Description: Position: 1 SubFamily: Edgebander BATCH 1 Brand: BIESSE Model: STREAM B1 10.5 MDS Type of edging Thin edge Thick edge Gluing System EVA Hotmelt  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  ,  , Premilling Unit , Corner Rounding Unit Grooving Unit , Maximum panel thickness 60 mm Max. panel height 60 mm Min. panel length 150 mm Min. panel width 65 mm Min. edge thickness 0.3 mm Max. forward feed speed 25 m/min Pressure with rubber belt Panel support guides , with positioning by NC , Infeed panel alignment system , MDS No. Panel Sizing / Milling units Unit : pre-milling unit automatic timed intervention Edge coil magazine , no. positions 12 glue pot for EVA hot melt glue , premelter for EVA hot melt glue , no. pressure roller 4 with positioning by NC , No. Edge Process ...

Description: Max. panel width 3300 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 30 m/min Conveyor Track with dogs , Pressure with rubber belt NO. PANEL SIZING / MILLING , Unit : scoring unit motor power : 4.4 KW r.p.m. : 6000 RPM NO. PANEL SIZING / MILLING , Unit : double chipper, top and bottom Constructor model : 75.30 NO. PANEL SIZING / MILLING , Unit : miller hogger NO. PANEL SIZING / MILLING , Unit : miller hogger Edge coil magazine , no. positions 2 glue pot for EVA hot melt glue , premelter for EVA hot melt glue , Roller set to press the edge , no. pressure roller 5 No. Edge Processing Units , Processing Unit : end trimming Constructor model : 08.412 no. motors : 2 Processing Unit : fine trimming to trim and round Constructor model : 08.055 no. motors : 2 Processing Unit : Corner rounding Constructor model : ...

Description: Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 5 mm Max. forward feed speed 12 m/min Pressure with idle wheels NO. PANEL SIZING / MILLING UNITS , Unit : pre-milling unit automatic timed intervention motor power : 1.8 KW Edge coil magazine yes glue pot for EVA hot melt glue , premelter for EVA hot melt glue , Roller set to press the edge , no. pressure roller 4 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.35 KW NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2 motor power : 0.65 KW NO. EDGE PROCESSING UNITS 3 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.65 KW NO. EDGE PROCESSING UNITS 4 Processing Unit : Corner rounding no. motors : 2 motor power : 0.5 KW NO. EDGE PROCESSING UNITS 5 Processing Unit : edge scraping NO ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Premilling Unit yes Corner Rounding Unit yes Max feed speed 14 m/min Maximum panel thickness 60 mm Operating Units 8 nr Min. panel height 8 mm Max. panel height 60 mm Min. panel width 70 mm Min. edge thickness 0.3 mm Max. edge thickness 3 mm Max. forward feed speed 14 m/min Top pressure yes Pressure with idle wheels Panel support guides yes with positioning by NC yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Lamps to preheat the side of the panel yes Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes premelter for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 with positioning by NC yes No. Edge Processing Units 6 NO. EDGE PROC ...

Production hall hbs780s and warehouse hbs645s, which are to be dismantled in the short term. These are thermally insulated halls whose supporting structure and cladding as well as various accessories can be reused. Production hall hbs780s GFA area: approx. 780 m²; Hall width: approx. 30.00 m AK façade; Hall length: approx. 26.00 m AK façade; Frame spacing: approx. 5.60 m MM truss; Eaves height: approx. 7.75 m OK purlin; STRUCTURE: The primary structure consists of hot-rolled Euro profiles. The secondary structure to accommodate the building envelope consists of cold-formed steel profiles made of galvanized strip steel. ROOFING: Sandwich panels, grey-white, on purlins made of cold-formed and galvanised lightweight profiles. WALL COVERING: Sandwich panels and thermally insulated sheet steel cassettes on wall substructure made of cold-formed and galva ...

Description Heating floors with jelly molds for baby food in melanin. Compression molding of elastomers and thermosets. CE declaration of conformity. Features: -Sized heated platens: 700x500 mm -Opening molds max.:620 mm -stroke mobile max.: 500 mm -Come closure adjustable (mold): 300-3000 kN -Pressure : 235 bar - copression speed, force max. (adjustable): 300-3000 kN -Power top hot floor: 6kW -Power less warm floor: 6 kW -Temperature hot plate : 50-250 °C -height work plan: 1530 mm from the floor ( a platform of 400 mm with guards is reccomended)

Description: Min. edge thickness 0.3 mm Max. edge thickness 3 mm , Max. forward feed speed 25 m/min Pressure with rubber belt Panel support guides , with positioning by NC , Infeed panel alignment system , NO. PANEL SIZING / MILLING UNITS , Unit : pre-milling unit automatic timed intervention motor power : 3 KW r.p.m. : 9000 RPM Lamps to preheat the side of the panel , Edge coil magazine , glue pot for EVA hot melt glue premelter for EVA hot melt glue , Roller set to press the edge no. pressure roller 7 with positioning by NC , No. Edge Processing Units 7 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.8 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2 motor power : 1.5 KW r.p.m. : 12000 RPM , NO. EDGE PROCESSING UNITS 3 Processing Unit : Corne ...

Manufacturer: Norden Model: NM 250 HA Year: 2003 Type: Hot air plastic tube filler / sealer Max capacity : 25 units / min Transport chain : 14 buckets Empty tube feeding : manual Tube printing centering 20 L hopper HA hot air device Ribbed or smooth sealing 1 side coding: 6 characters Verification check: no tube - no filling Available formats. Cutting recovery: CFM R154V hoover ThermoChill I Recirculating Coolers General information Filling volumes: 1ml - 300ml. Diameter: 10 mm - 50 mm

Description: Max. panel height 55 mm Min. edge thickness 0.4 mm Max. edge thickness 12 mm Max. forward feed speed 13 m/min Pressure with idle wheels NO. PANEL SIZING / MILLING UNITS Unit : pre-milling unit automatic timed intervention motor power : 2.2 KW Edge coil magazine glue pot for EVA hot melt glue premelter for EVA hot melt glue Roller set to press the edge no. pressure roller 4 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 automatic timed intervention motor power : 0.35 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim and round no. motors : 2 motor power : 0.55 KW r.p.m. : 11300 RPM NO. EDGE PROCESSING UNITS 3 Processing Unit : Corner rounding no. motors : 2 motor power : 0.4 KW NO. EDGE PROCESSING UNITS 4 Processing Unit : glue scraping NO. EDGE PROCESSING UNITS 5 Processing Unit : buffing no. motors : 2 motor  ...

CONTROLS   PLC SIEMENS FEEDSTOCK STEEL STRIP   sheet width max.: 450 mm   sheet width min.: 90 mm   sheet thickness max.: 13 mm   sheet thickness min.: 2 mm   exterior coil diameter max.: 1900 mm   exterior coil diameter min.: 1100 mm   internal coil diameter max.: 760 mm   internal coil diameter min.: 610 mm PRODUCT (PROFILE, TUBE)   external diameter min.: 30 mm   external diameter max.: 140 mm   wall thickness min.: 2 mm   wall thickness max.: 12 mm   length min.: 4000 mm   lenght max.: 10000 mm LINE CHARACTERISTICS   Forming Process: rollforming   welding process: HF inductive   sawing process: travelling   speed max.: 65 m/min   feedstock transport direction: left to right Line consis ...

manual casemaker CMC Q-cover 1 (similar to LPA 50-110) format: max 50x110cm; min. 12x15 cm Machine comprising of: - Gluer for hot and cold glue (PVA) - Vacuumtable with board guides for 1-3 cardboards (up to 5 as option) - Turning in unit (1 side) - Roller press - Delivery table

Hot shortage of vintage vintage post-war goods Electric 230 V was still in use until 1990 in the private sector

FORMAT 76x100 cm for the production of folders (CD)Hullen, etc. Estro unit for capacitive folders (3D) Hot glue with 2 dues very good condition Option with Fidia Vetta folder locking unit (MHGraphics is Fidia-dealer) This price includes transport, installation and instruction (3 days) in Germany/Austria/Switzerland/France/Belgium/Niederlaende/Scandinavisin/ Poland. New price Euro 185.000 Available: immediately/Imm.

1 x Farrel Bridge four roll inclined Z formation Calender Year: 1956, Roll dimensions: 710mm dia. x 1675mm wide, Peripherally drilled rolls for heating/cooling, Drive configuration: 250 HP DC v/s motor through unidrive gearbox Roll differentials: 1&2 15%, 2&3 3%, 3&4 3% No. 4 bole speed Max 75m/min Main and auxiliary bearings: Bronze Bush type, Bearing lubrication: Re-circulating oil. Roll heating: High pressure hot water 17 bar capacity. Cheek material guides rolls 1 & 2: Fully adjustable width using 0.75 kW motor. Cross axis – yes (roll 4). Motorised roll nip adjustment – Roll adjustment 1, 2 ,and 4 – 3.75kW motors – Cross axis adjustment roll 4 – 3 kW motor, max adj. 50mm. Hydraulic pull backs – max pressure 70 bar.

Suction wall with exhaust air unit, supply air unit, supply air filter, hot water heating register Suction wall: Make : Krautzberger, built 1992 Dimensions: 2.2 x 3.0 x 0.8 m (approx. BxHxT) Fan: 9,240 m3/h suction power, 2 kW Ex Supply air filter, supply fan, WW heater register: Make : Wolf, built 1999 Fan: 10,000 m3/h suction power, 9 kW Heater: 56 kW, 120 degrees C, 3,500 m3/h Pipeline : supply and exhaust air ducts, deflector hood We also have complete painting booths, drying booths and spare parts for painting systems in stock, e.g. Aggregates, lights, filter ceilings, entrance gates, roller doors, gratings, air ducts, etc. Please ask.

a top-class convectomat, hot air damper / convectomate/ combi damper / CombiMaster , gas-heated, 50-250C. External dimension: 1240x960x1400mm, internal dimension: 620x640x830mm with stikken trolley for 10xGN2/1. Electrically controlled, 400V, 0.3kW. Good condition.

Ermafa twin screw extruder B 2.95-35 D 1992/1995 -Extruration plant for recycling -with hot-tee, Filter -Drying centrifuge, -Degassing plant, -storage silo, -discharge silo, -Chain elevator. -900-1000 kg/h PP

Cat.-Nr. 11-3200 new Necessary space for mash and lauter tun: LxWxH: 3 x 2 x 2,80 m Necessary space for tanks: LxWxH: 4,0 x 5,0 m complete 2 brews / day = 10hl Basic Equipment The Brew House is complete with all equipment. All equipment are with high standard an very simple to use. This 5 hl Brew House is built as 2 devices-brew house manual version with manual butterfly valve. It is possible to make 2 brews/day (10 hl) Technology All the pipes can be cleaned and sterilized in the circuit over the pump included. a) In the mash boiler the mash will be cooked, then it will be pumped with one beer pump made of stainless steel from mash boiler to the lauter tun. b) After the lauter wort will be pumped back to the mash boiler. c) After emptying the lauter tun the grit floor will be removed. The lauter tun will be changed to a whirlpool. d) After cooking th ...

Cat.-Nr. 11-3210 new Basic Equipment The Brew House is complete with all equipment. All equipment are with high standard an very simple to use. This 10 hl Brew House is built as 2 devices-brew house manual version with manual butterfly valve. It is possible to make 2 brews/day (40 hl) Technology All the pipes can be cleaned and sterilized in the circuit over the pump included. a) In the mash boiler the mash will be cooked, then it will be pumped with one beer pump made of stainless steel from mash boiler to the lauter tun. b) After the lauter wort will be pumped back to the mash boiler. c) After emptying the lauter tun the grit floor will be removed. The lauter tun will be changed to a whirlpool. d) After cooking the hops a special injection valve is introduced inside the lauter tun so that it can be used as a whirlpool. Mashing Tun / Wort Boiler Volume brutto: ...

Therapy bathtub, with hydromassage unit/device, stainless steel tub with various water jets, pump, with cold and hot water connection, patient lift, external size 1860x2500x960mm, inner dimension 1800x2340x570mm. New condition.

Amut Type EA 160 Monoscrew Extruder Complete extrusion line for recycling. 2002 New screw and motor. with hot separator, centrifuge, filter, degassing system 900-1000 kg/h PP 800-900 kg/h PE Poverty Recycling Extruder PP=900-1000kg,built 1997, 900-1000 kg/

Ladies and gentlemen, we offer: Biomass Container Heating incl. storage container with hydr. Shear floor discharge Plant complete with saemt installations Heating capacity 450 kW reachable by conversions now 480 kW Hot water production Fuel: coarse, moist spaene, wood chips up to 40% HF Best measurement results: Dust content 0.04 g/m3 at exhaust temperature of 170 degrees C For more information and pictures we are available. All prices are from Station Europa and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been signed. Mistake reserved. All technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any w ...

1 of used tray-/padshrinkpacker, make KHS Kisters, type Innopack TSP 80 V with 180-degree (clockwise) curve and shrinktunnel, new 2004. Machine has an 8-lane infeed and is capable of producing trays (and/or) pads either single lane (i.e. 24 cans/bottles per tray/pad) or dual-lane (i.e. 12 cans/bottles per tray/pad) in shrinkwrap film (print-registered), at a maximum capacity of 80 cycles (i.e. 80/160 trays) per minute. Operating direction: from right to left as seen from operator\s station. With Allen Bradley Control Logix PLC / Panel View 1000, Indramat servo drives, ITW Quattro hot-melt unit. Both packer and shrinktunnel easily adjustable via servo\s and spindles for various formats as well as single-/dual-lane. Wired for 480V/60Hz. Various manuals available. Equipment in excellent condition!