138,291 used machines on RESALE, but how to find them? Machine Search
clamping force: 500 kN injection volume: 76,5 cm³ screw diameter: 32 mm platen size: 360 x 335 mm Condition: used, as good as new Specification: Injection moulding machine for LSR - Demonstration machine as good as new clamping unit: - clamping unit: horizontal - Clamping force: 500 kN - Opening stroke max.: 400 mm - Platen distance max.: 650 mm - Mould installation height min.: 250 mm - Clear width between the tie bars: 360 x 335 mm - Ejector stroke max.: 80 mm Injection unit SP 82: - Screw diameter: 32 mm - Screw L/D ratio: 16.3 - Screw stroke max.: 95 mm - Injection volume max.: 76.5 cm³ - Injection pressure: 1076 bar - Plasticising flow: 13 g/s - Injection flow: 204.8 g/s - Connected load: 3x 400 V, 50 Hz - Max. heating power: 5.8 kW - Drive pow ...
Single-column eccentric press HELMERDING type TPEP 12 BMasch. No. 831-101 Comm. No. 76228 Year of construction 1976Compressive force 12 ton. Projection 155 mmTable surface 400 x 320 mmTable opening 125 mmPlunger area 125 x 100 mmLifting adjustment 6-60 mmRam adjustment range 40 mmClamping pin hole 25 mm with clamping pieceInstallation height max. 250 mmStroke rate 180 strokes/min. Drive power 1.1kW- Electric foot switch and 2-hand operation- Setup, single stroke 2-hand, single stroke foot and continuous running foot, automatic
Compressed air toggle press BURGER type D04Fabr. No. 4497 Year of construction approx. 1972Compressive force max. 6 ton. Projection 150 mmPlunger stroke 39 mmTable size 340 x 270 mmThrough-hole opening 46 mmInstallation height max. 160 mmTool holder 25 mmPlunger plate 90 mmPneumatic operating pressure 5 barMains connection 220 V 50 Hz- Pressure regulator for press force adjustment- Lifting height adjustment 7, 21, 40 mm- Electric foot switch- Table height adjustmentSpace requirement L x W x H 700 x 500 x 1300 mmWeight
2-column hydraulic press SELF-MADEBaucy approx. 1980Compressive force 6 ton. at 180 barCompressive force 5 ton. at 150 barCompressive force 4 ton. at 120 barCompressive force 3 ton. at 90 barTable top 400 x 340 x 30 mmPlunger plate 410 x 350 x 28.5 mmTable usable area between the guide columns 305 x 245 mmPlunger stroke 140 mmInstallation height max. 320 mmColumn diameter 35 mmTable height above floor 1050 mmHydraulic operating pressure max.180 barMotor power 4 kWNet connection 380 volts, 50 Hz- stepless
SPECIFICATIONS: Working width: 3000 mm Working height: 2500 mm Expandable bottom stop Equipped with manual workholding system 02 Pressing devices Hanging control panel Installed power: 1.8 kW
Machine name: Filter presses frame used Manufacturer: Passavant Type: 1200 x 1200 mm Year of Make: 1991 Design: Bridge spar press Filter pressure: 15 bar Press capacity: Possible approx. 2200 liters m2 Procedure: Closed Filter area: Possible approx. 160 m2 Plate format: For 1200 x 1200 mm Number of plates: Without plates but suitable 66 with 30mm cake thickness Plate Conveyor: Automatic Filter Cloth Washer: Yes Cake thickness: 30 possible Dimensions: L 6,700 x W 1,800 (2,400) x H 2,250 + 500 mm Curb weight: Approx. 14000 kg Tech. Documentation: Yes Note: Without plates but with 66 carriages for hanging the filter plates Accessories: A light barrier and a filter cloth washer Condition: Used Price: On request
Through-hole filter cloths for chamber filter press Length plate format in mm: 2000 Width flap format in mm: 1500 Cloth Design: Through-Hole Cloth Hem in mm: 30
Filter Cloth for Chamber Filter Press Length plate format in mm: 2000 Width flap format in mm: 1500 Cloth Design: Through-Hole Cloth with Velcro Hem in mm: 30
Mechanical Dorst TPA 45, Pressing Force max. 450 Kn, Withdrawal force max. 250 Kn, Supporting force in pressing position max. 130 Kn, Die return force max. 60 Kn, Upper punch stroke 120 mm, Upper punch adjusting travel 70 mm, Number of strokes 6-22 1/min, Filling height max. 120 mm, Pressing travel max. 60 mm, Withdrawal travel max. 60 mm, Top pressing travel max 6 mm, Upper punch pneumatic preload max. 30 mm, Compressed air supply , Air consumption , Intake air aprox. 70 l/min, Total connected load aprox. 14,0 Kw, Press dimensions:, Width aprox. 1550 mm, Depth aprox. 1650 mm, Height aprox. 2200 mm, Weight of the press aprox. 3900 Kg, Oil filling quantity :, Press housing 45 l (gear oil), Workplace-related sound 79 dB (A)
Pressing Force max: 1400 Kn, Withdrawal force max: 1100 Kn, Die return force max: 70 Kn, Upper punch stroke: 220 mm, Upper punch adjusting travel: 220 mm, Number of strokes: 5-18 1/min, Filling height max: 180 mm, Pressing travel max: 90 mm, Withdrawal travel max: 90 mm, Top pressing travel max: 18 mm, Total connected load aprox: 25,0 Kw, Width aprox: 1950 mm, Depth aprox: 1750 mm, ISO 9001: 2008 CERTIFIED COMPANY, Height aprox: 4380 mm, Press housing: 240 l (gear oil), Workplace-related sound: 78 dB A
A Hämmerle hydraulic press brake is available. Pressing force: 2000kN, working length: 2600mm, installation height: 830mm, stroke: 265mm, throat depth: 300mm, rapid traverse: 100mm/s. Machine dimensions X/Y/Z: approx. 3750mm/2600mm/3600mm, weight: approx. 16000kg. The machine is not functional. Documentation available. On-site inspection is possible.
pressure: 60 t throat: 280 mm stroke: 10-140 mm no. of strokes: 110 Hub/min ram - range of adjustment: 60 mm table surface area: 740x560 mm ram surface: 380x195 mm hole in the table: 300x200 mm table height: 760 mm tool hole in ram: Ø 40 mm weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Nominal pressing force ... 100t Table dimensions ... 1000 x 640mm Stroke adjustment ... 125mm Plunger adjustment ... 90mm Number of rams ... 75-150 rpm Main engine power ... 6/10kW L x W x H ... 1725 x 2230 x 2970mm Mechanical weight ... 10100kg
pressure: 35 t throat: 220 mm stroke: 8-96 mm no. of strokes: 120 Hub/min ram - range of adjustment: 50 mm table surface area: 580x440 mm ram surface: 305x170 mm hole in the table: 215x175 mm table height: 870 mm tool hole in ram: Ø 40 mm weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(), 30kW - Japanese standard Pgsc N D D Hou Dxb Tjxop Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.
pressure: 45 t throat: 230 mm stroke: 4-80 mm no. of strokes: 120 Hub/min ram - range of adjustment: 55 mm table surface area: 695x455 mm ram surface: 365x180 mm hole in the table: 220x180 mm table height: 890 mm tool hole in ram: Ø 40 mm weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 100 t throat: 300 mm stroke: 10-140 mm no. of strokes: 60 Hub/min ram - range of adjustment: 60 mm table surface area: 800x500 mm ram surface: 430x230 mm hole in the table: Ø150 mm table height: 860 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 5,2 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 160 t, 4000 mm
160 ton x 40000mm Multi Axis CNC
gebr. Slotted Hole Drilling Machine GANNER GANNOMAT Junior LBM 320 Drilling on 2 levels YOC 1992 Motor power: 1.5 kW (380V / 16A plug) Rated current: 3.4 A Spindle speed: 3,000 rpm Pneumatic height adjustment: 150 mm Clamping height of the workpieces: max. 250 mm Working height: 850 mm Dowel pitch: 12 mm 2-lever operation 2 pneum. Workpiece clamp 3 plug-in stops (2x 90°, 1 x mitre stop) Compressed air connection: 6 bar Weight: 270 kg Floor space: 1,200 mm x 1,000 mm Technical data according to manufacturer's specifications.
Inv. Num. : 8583 Type: REP 100 Producer: Heilbronn Created: 1989 Parameters: Compressive force: 100 t Stroke length: 6-100 mm Maximum stroke rate per minute: 100 1/min Total power requirement: 11 kW Machine weight: 7000 kg
Inv. Num. : 8584 Type: PEDA 160 Producer: IWK Created: 1972 Parameters: Compressive force: 160 t
Inv. Num. : 8585 Type: KPRW 160 Producer: Kieserling Created: 1972 Parameters: Compressive force: 160 t
Complete wood pellet production line up to 2000kg/h. Currently still connected, can be launched, tested. Sold for dismantling. The entire line - from automatic sawdust feeding to semi-automatic packaging in PE bags or big bags. The line is equipped with a sawdust moisture flow meter (German) that constantly measures sawdust moisture after drying, making it much easier for the operator to regulate the drying process. 2-3 workers worked per shift. Granulator - 2x55kW motors, matrix diameter 450mm.
Key data: 5 t, 150 mm
Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed (Approach Fast Speed: 350 (mm/s) Lower Speed (Under Pressure Slow Speed: 36mm/s Rise Speed 250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size Height (mm) 986 Width (mm) 485 Depth (mm) 920
Manufacturer: KBA Model: 46DI Year of Manufacture: 2004 Type of Machine : 4-color offset printing press Includes transport pallet and server 5.8 million impressions total Production speed: 7,000 sheets per hour Comes with inks and maintenance materials (including 4x4 CMYK) Installation area: approx. 350 x 300 cm Complete maintenance performed in July 2022, including full disassembly, cleaning, and reassembly Find more here - .ucymachines/ Contact us at - sales@ucymachines
Working width: 2500mm, max. sheet thickness aluminium/steel/stainless steel: 3mm/2mm/1.25mm, feeding length range: 575mm-2500mm, feeding width range: 210mm-1500mm, max. bending height: 200mm, max. negative bend: 35mm, max. diagonal twist: 3300mm, rotary table position: 0°/90°/180°/270°, working height: 1150mm. Clamping stroke: 210mm, clamping force: 240kN, clamping lowering and return speed: 50mm/s, upper beam swivel range: 135°, upper beam swivel speed: 90°/s, lower beam swivel range: 135°, lower beam swivel speed: 90°/s. Machine dimensions X/Y/Z: approx. 4050mm/1600mm/2400mm, weight: approx. 13000kg. Documentation available. An on-site inspection is possible.
Brother Hi-Spin riveting machine 5mm high spin Type: BR1-103 - Crimping ability (Mild steel rivet) φ5mm or less - Spinning head: 20-40mm - Distance between tabletop and punch: 60-180mm - Table working surface size: 310 x 180mm - Processing time setting range: 0.3-5 seconds - Normal pressure: (Varies depending on pressing conditions) 2-5kg/cm2 Air consumption: Power supply and motor Three-phase 200V 0.2kw 4Pole Machine size Width 390 x depth 510 x height 1000mm Machine weight 95kg
Yoshikawa US-66 riveting machine 5mm high spin type: US 66 - Crimping ability (Mild steel rivet) φ5 mm or less - Spinning head: 5-40 mm - Distance between tabletop and punch: 90-285 mm - Table working surface size: 250x250 mm - Processing time setting range: 0.2-9 seconds - Normal pressure: (Varies depending on pressing conditions) 2-5 kg/cm2 Air consumption: Power supply and motor Three-phase 200V 0.12kw Machine size Width 330 x depth 610 x height 800mm Machine weight 95 kg
CONTROLS PLC SIEMENS S7 PRESS DESIGN drive system: knuckle-joint frame design: H-frame, monoblock openings in uprights: yes number of suspensions: 2 feedstock transport direction: left to right PRESS FORCES total force (nominal): 315 to nominal work capacity: 38 kNm PRESS TABLE table surface (left-right): 2000 mm table surface (front-back): 1200 mm thickness of bolster plate: 200 mm SLIDE slide force: 315 to table surface (left-right): 1995 mm table surface (front-back): 1100 mm stroke: 160 mm stroke rate (max.): 80 /min SLIDE (MECHAN. PRESS) slide adjustment: 140 mm stroke rate (min.): 20 /min stroke rate (max.): 80 /min main drive power: 90 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 555 mm distance between columns (H-frame): 2060 mm passline opening (free passag ...
Engel Injection Machine Type ES 1500T/160 V – ELAST Stroke slide plate 300mm Stroke central ejector for slide plate 100mm Force central ejector for slide plate 30kN Stroke lateral mechanical ejector 250mm Stroke lateral hydraulic ejector 250mm Force lateral hydraulic ejector 80kN Stroke central ejector 120mm Force central ejector 20kN Pump drive power 15kW Oil filling 1 225 Operating pressure of hydraulic system 250bar Capacity temperature control unit 2x3 kW Total connected load 48kW Dims: 2675mm long x 1350mm wide x 3310mm high Weight: 6900 With instruction manual
PRESS DESIGN drive system: hydraulic frame design: C-frame, single sided PRESS FORCES total force (nominal): 12 to SLIDE stroke: 200 mm ELECTRICAL SPECIFICATIONS mains voltage: 380 V mains frequency: 50 Hz DIMENSIONS / WEIGHTS total weight approx.: 1000 kg Hour counter: 30181 h last safety check: 27.07.2023, overrun time 38 ms, overrun distance 60 mm
pressure: 1000 t distance between columns: 5000 mm stroke: 500 mm Height of centres: 400 mm Motor output: kW reus: U/min Overall size: 6000 x 2500 mm Weight: 1000 kg Distance between centres: 3500 mm total power requirement: kW weight of the machine ca.: 220 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 8630 Type: EHP 50 Producer: Darley Created: 1997 Parameters: Control system: DELEM Compressive force: 50 t Maximum bending length: 2000 mm Machine weight: 2600 kg
Capacity (ton) 315 Table size, mm 2500 x 1250 Slider stroke, mm 400 Shut height,mm 750 Strokes per min 25 Press weight, kg 50900
RONCHI TABLET PRESS, MODEL PA20 Year of manufacturing: 2003 High-speed tablet press for the dosage, pre-compression and compression of solids for the production of tablets. For use with Euro D tools. Documentation available. CHARACTERISTICS • Tool size: Euro D PRODUCTION • Production capacity: 56,000 tablets/h • Punches sizes available: Ø20 mm (complete) + Ø8 / Ø11 / Ø13 / Ø16 (4 punches + covers for small production runs) Number of punches: 20 units • Max. tablet diameter: 25 mm • Max. compression force: 10,000 Kg DIMENSIONS • Size: 83 x 130 x 175 cm
Press brake with Stäubli robot cell press Manufacturer: LA G Model: GBS R 1250 50 The machine was only used for a very short period of time.
Height=0.92 m, Overall length= 0.6 m, Overall width= 1.22 m, Net weight= 170 kg,
Press capacity: 63 ton Ram stroke adjustable: 8 - 60 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 300 mm Table surface area : 810 x 550 mm Slide area: 700 x 420 mm Hole in table: 550 x 140 mm Distance between oil tray: 700 mm Table height over floor: 920 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 8 ton Dimensions L x W x H: 2935 x 1170 x 3000 mm Main Motor: 11 kW
The Dorst TPA 50/4 is a reliable, used mechanical powder compaction press designed for precision and efficiency. Offering a robust maximum pressing force of 500 kN and a maximum withdrawal force of 400 kN, it supports a variety of powder compaction tasks. With a filling height up to 180 mm and a pressing stroke of up to 90 mm, this machine is adaptable to diverse requirements. Equipped with an upper punch stroke of 120 mm and an adjustable travel of 220 mm, the Dorst TPA 50/4 provides flexibility for different applications. It operates at a speed of 7 to 32 strokes per minute, ensuring efficient production. The press requires a compressed air supply, consuming approximately 200 liters per minute, with a total connected load of around 18 kW. Constructed with durability in mind, the press measures approximately 2000 mm in width, 1700 mm in depth, and 3250 mm in height, and weighs around 5, ...
Capacity: 35 ton Throat depth: 225 mm Ram stroke: 8 - 80 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 325 mm Table surface area : 600 x 450 mm Slide area: 300 x 225 mm Number of strokes: 160 s.p.m. Required power: 2,2 kW Dimensions L x W x H: 1000 x 1600 x 2200 mm Weight of machine approx.: 1,9 ton
The Dorst TPA 5 is a refurbished mechanical powder compaction press, designed for precision and efficiency in industrial applications. It offers powerful performance with a maximum pressing force of 50 kN and a withdrawal force of up to 40 kN. This makes it suitable for a variety of powder compaction tasks, with a filling height of 50 mm and pressing travel capability of 25 mm. This machine provides flexibility with an upper punch stroke of 85 mm and an adjustable travel span of 70 mm, operating at 6 to 30 strokes per minute. It consumes around 50 liters of compressed air per minute and has a total electrical load of approximately 4.00 kW. With durable construction, the Dorst TPA 5 maintains a quiet operation at a sound level of 70 dB(A). The presss compact dimensions, approximately 1200 mm in both width and depth and a height of 2150 mm, with a weight of about 1,200 kg, make it a manage ...
Punching width: 500mm, rated current: 20A, control voltage: 220V, weight: 2.5t. No defects known, regularly maintained, operating hours unknown. With punching tools and punching blade, only little documentation available. An on-site inspection is possible.
pressure: 20 t throat: 200 mm stroke: 0 - 50 mm table:: 360 x 550 mm table:: 140 mm - Bohrung no. of strokes: 160 Hub/min bore: 35,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 240 mm total power requirement: 2,2 kW weight: 1.250 kg range L-W-H: 1310 x 1250 x 1860 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 20,0 t stroke: 185 mm table surface area: 170 mm Breite column travel between the guideways: 510 mm weight of the machine ca.: 112 kg dimensions of the machine ca.: 1630 x 560 x 730 mm Furnishing: - Standard with pressure cylinder that can be moved to the left and right - For aligning, pressing, bending, assembling gears, discs, etc. - Standard with foot pedal and hydraulic hand pump for piston delivery - Standard with support prism for aligning shafts - With automatic piston retraction by integrated return spring as standard - Height-adjustable press table with locking bolts - Large manometer for reading the compressive force - Including two-stage hydraulic pump - Robust construction with welded steel frame The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 30 t stroke: 150 mm table surface area: 185 mm Breite column travel between the guideways: 530 mm weight of the machine ca.: 162 kg dimensions of the machine ca.: 800 x 700 x 1805 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 50 t stroke: 200 mm table surface area: 730 x 205 mm dayligth: 1050 mm column travel between the guideways: 730 mm weight of the machine ca.: 288 kg. Description : - Standard with cable winch - for easy height adjustment of the support table - Piston delivery either manually or pneumatically - Powerful workshop presses for craft and repair businesses - Optimum price-performance ratio thanks to rational design - The standard foot pedal keeps your hands free for the workpiece - Increased range of application thanks to the optionally . available pressure mandrel set (10 pieces). - Pressure cylinder with integrated return spring for piston return - Welded steel frame for heavy use and high stability - Versatile in use thanks to the pressure cylinder that can . be moved to the left and right The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 85.0 t chamfer lenght: 2050 mm distance between columns: 1750 mm column arm: 410 mm stroke: 365 mm dayligth: 535 mm ajustment speed: 200 mm/sec working feed: 1.0 - 10.0 mm/sec return speed: 135 mm/sec back stop - adjustable: max. 600 mm table width: 120 mm work height max.: 1050 mm Number of working hours: 28.500 h oil volume: 200 l operating pressure: 340 bar total power requirement: 14.0 kVA weight of the machine ca.: 9050 kg range L-W-H: 2680 x 2100 x 2885 mm with increased installation height / piston stroke very well maintained condition () with only approx. 28.500 operating hours - in checked condition - machine video - https://www.youtube.com/watch?v=ZuwyPKJSYLw Equipment: - CNC electro-hydraulic press brake - including DELEM CNC control swiveling control panel at the front left - CNC controlled axes: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motoriz ...
pressure: 1000 kg throat: 95.0 mm table length: 120 mm table width: 120 mm total power requirement: manuell kW weight of the machine ca.: 17.0 kg dimensions of the machine ca.: 270 x 130 x 330 mm Description: - For pressing in and out bearings, bushings, etc. - Made of torsion-resistant steel - Includes mounting holes, ideal for mounting on a workbench - Suitable for bushing removal, straightening, bending, reaming, etc. - Adjustable lever bar, depending on the required force - Ideal for repair shops and general workshop use The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 175 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 180 mm/sec return speed: 135 mm/sec work speed: 10,0 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 90,0 mm oil volume: 200 ltr. voltage: 400 Volt total power requirement: 15,0 kW weight: 11.950 kg range L-W-H: 5100 x 2150 x 2850 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-58T graphics / touchscreen 2D graphic programming 15 high definition color TFT screen Bending sequence calculation Product programming and display in real size USB interface - Motorized backgauge with R-axis, on recirculating ball spindles - ...
maximum number of results exceeded
please refine your search
