hot forging press used for sale

for production of forgings by forging of ferrous, non-ferrous metals and alloys in the hammer dies model M212 Impact energy, 50 kJ Nominal weight of falling parts, kg 2000 Stroke woman, mm 1200 Stroke woman, mm 1200 Machine dimensions Length Width Height (mm) 3650X1660X5310 Weight kg 58.310, spare parts available

Complete Mechanical Upgrade by GFM, with increase of Power to 900 Ton/hammer and new CNC in 1991 Numbers ̈of Hammers: 4 Forging force: 3.600 Ton (900t per hammer) Strokes per minute: 270 Maximum diameter of forging: - circular cross section: Ø 400 mm - square cross section: 320 mm Minimum output diameter: - circular: 60 mm - square: approx 50 mm Maximum length of forging with/without lateral reception: 8.000 mm / 9.700 mm Feed of manipulator A: 7.140 mm Feed of manipulator B: 9.940 mm Workpìece weight: 2500 kg Total power supply (nominal power): ca 1.600 kW Machine weight: 493.000 kg

Key data: 150 kg, 480 mm, 375 mm

Hammer weight: 150 kg Stroke length: 480 mm Stroke rate: 168 p/min. Projection: 375 mm Plunger diameter: 180 mm Origin: England Motor power: 11 kW Machine LxWxH: 200 x 180 x 240 cm Machine Weight: 6000 kg

Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg

Offer 25443 Specifications: - Bear weight 40 kg - Impact regulation - Lifting height infinitely adjustable 200 mm - Impact rate approx. 220 1/min - Projection 280 mm - Anvil - height approx. 560 mm - Anvil - Weight 250 kg - Drive 380 V / 4 kW - Space requirement approx. W 850 x H 1100 x D 1350 mm - Weight approx. 850 kg

Air steam die forging hammer : Capacity : 16 tons, Nominal mass of drop parts : 16000 kg, Impact energy : 400 KJ, Ram stroke : 1500 mm, Ram stroke per minute : 20, Distance clear between guides : 1180 mm, Ram dimensions front to back : 1500 mm, Die holder dimensions front to back : 1600 mm, Bottom die impression to floor distance : 500 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions : - Floor space : 4500 x 2450 mm, - Height above floor level : 7920 mm, Mass of anvil block : 325 tons, Total weight of hammer : 425 tons.

Capacity 7.25T /16000lbs Stroke 1727 mm weight 270t

Capacity 5.4T /12000 lbs Stroke 1626 mm weight 150t

Capacity 2.7T /6000 lbs. Stroke 1403 mm weight 77.5t

Metallography Mounting presses ECOPRESS All ECOPRESS presses can be programmed by the user in a simple manner, that the mounting process runs fully automatically. When the ECOPRESS 50, one program can be stored in the control electronics. A rugged bayonet allows quick and safe operation. The ECOPRESS series offers a wide variety of different size of molds of 25 - 50 mm in diameter. At the same time two samples can be embedded per cylinder with an intermediate piston. Alternatively, machine type of ECOPRESS 200 twin-piston for up to at the same time 4 embeds is available. When baked in the samples into plastic granules are melted, that the sample under heat and high pressure wraps pore-free and then through a press cylinder, electronic control, integrated cooling for solidifying. ECOPRESS 50 one cylinder, electronic control, full automatic program ECOPRESS 100 one pressing  ...

Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm; -height: 1280 mm Main motor: 400/590 kW/rpm Press layout dimensions: 6300x8965 mm Total height: 11125 mm Height above floor level: 9150 mm Total weight: 626100 kg

NOTE additionally a new shaft Description Force , 4000 TN Slide stroke, mm 400 Number of continuous slide stroke, stroke / min 50 Closed height of stamping space mm 1000 Adjusting the table mm 15 Distance between columns in light,mm 1660 Drive power, kW 185 Table dimensions in plan mm: - From left to right in 1620 - Front-to-back in 1570 Dimensions in mm: - in the plan 6100 x 4710 - Height above floor level 6820 - Press height 8680 Weight, t 377

HOT PRESS MODEL PL 90s 3000x1300 mm PS VBO TECHNICAL CHARACTERISTICS Platens dimensions 3000x1300 mm Stroke 400 mm Type of stroke Upstroke design (from bottom to top) Type of platen Assembled platens with coil and aluminum covering Total thrust 90 ton on 80% of the surface Pressing Cylinders N° 6 cylinders ø70 mm Specific Pressure 2.05 kg/cm2 on 100% of the surface 2.56 kg/cm2 on 80% of the surface Loading and Unloading Side3000 mm side Type of Heating system Oil boiler ? maximum temperature = 120°C Heating system specificationsElectric boiler 18 kW Opening Automatic by timer Control Board Standard Power supply 400V, 50Hz, 3ph Security device Safety rope around the press Red emergency Button Two Hand control Norma ...

Kniehebelprägepresse - Embossing hot stamping press Hans Schilling HSM Serial-No. 18040 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Heißpräge - Kniehebelprägepresse - Embossing Hot Stamping Press Krause FNP Serial-No. 4798 Stamping size: 550 x 400 mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

New hot press, hydraulically Brand: ITALPRESSE Type XL/6 30-13 PEA Golden electric heating plate surface anodized to ensure high surface hardness and excellent corrision protection. - Electrical - heating plates: 3000 x 1300 mm - Total pressure: 120 to. - Number of hot plates: 2 pc. - Number of floors: 1 pc. - Stroke: 350 mm - Day light opening: 350 mm - All-round feeding - Number of cylinders: 6 pc. - Diameter of cylinder: 85 mm - Power consumption (hydraulic unit): 3 kW - Electric - combi - heating plates made out of two components: Aluminium - electric - heating plate Iso printing plate - Heating power 22 KW - High pressure isolation plates - Operating temperature: 70 - 90° C. - Max. Temperature: 120° C. - Supply: 400V/50 Hz - Safety accordance with CE standard Standard equipment: - Movement of the press table with rack and pinion parallel guidance at t ...

CONTROLS   PLC SIEMENS S7 300 PRESS DESIGN   drive system: hydraulic PRESS FORCES   total force (nominal): 800 to PRESS TABLE   table surface (left-right): 2000 mm   table surface (front-back): 2000 mm   height above floor level: 700 mm SLIDE   table surface (left-right): 2000 mm   table surface (front-back): 2000 mm   stroke: 900 mm SLIDE (HYDR. PRESS)   approximation velocity max.: 400 mm/s   working velocity min.: 5 mm/s   working velocity max.: 160 mm/s   return velocity max.: 300 mm/s TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 1700 mm   distance between columns (H-frame): 2100 mm ELECTRICAL SPECIFICATIONS   total power consumption: 370 kW   mains voltage: 400 V   mains freq ...

CONTROLS   PLC SIEMENS S7-400 PRESS DESIGN   drive system: hydraulic   number of suspensions: 1   slide ejectors / cushion: no   table cushion: no   opening in table: no   feedstock transport direction: back-front PRESS FORCES   total force (nominal): 1000 to PRESS TABLE   table surface (left-right): 2066 mm   table surface (front-back): 2000 mm   height above floor level: 630 mm SLIDE   stroke: 900 mm SLIDE (HYDR. PRESS)   approximation velocity max.: 600 mm/s   working velocity min.: 15 mm/s   working velocity max.: 40 mm/s   return velocity max.: 390 mm/s   return force: 100 to TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 1710 mm   distance table - slide max.: 1700 m ...

Hot plate press (electric) Brand: ORMA Type: NPC 6/120 new machine Technical data: Heating plates: 3500x1300mm Cylinder: 6 pieces Press force: 120t Stroke/opening dimension: 450mm Connection value: 28.8kW (ELKOM plates) Options: - Intermediate plate - Anodized surface for ELKOM panels - Parallelism sensor á 1,000.00 EUR - Pressing mechanism from above (fixed lower plate) - Max. temperature till 150°C - Max. temperature till 200°C - 4-sided loading possible - Mylar protective film - Fiberglass Teflon protection - Hardware for Industry 4.0

Eccentric shaft by drawing K04.038.842-22-402 for hot stamping press K04.038.842 (K8542), 1600T brand new in state stale from stock W 4675 kg

-Max pressure at the end of stroke – 4000 ton -Press stroke – 400 mm -Number of stroke – 50 per minute -Max distance of stroke from the table – 1400 mm -Dimensions of slider: 1320 x 1320 mm -Bed dimensions: 1120 x 1600 mm -Bed movement by height – 20 mm -Max pressure of upper ejector – 20 t -Max stroke of upper ejector – 65 mm -Max pressure of lower ejector – 40t -Max stroke of lower ejector – 80 mm -Main motor power – 225 kW -Main motor speed – 730 rpm -Total width — 6280 mm -Total depth – 4885 mm -Total height – 8870 mm -Height over the bed – 7315 mm -Total net weight – 280 092 kg

Prägepresse / Hot Foil Stamping Press

Built in 1993 semi-automatic hot stamping press Embossing format max. 125 x 280 mm electr. Drive 1 foil preference 1 heating plate automatic feed Unwinding device for round materials / cans Underframe Delivery date: immediately from stock Price on request. We supply and install worldwide.

Hot stamping hand lever press, embossing foils, silver gloss and gold luster among others are included Note: The operating hours are unknown. The entry 99999 hours is only pro forma and does not correspond to the actual hours

An OTT heating plate press is available. Pressing area X/Y: 2250mm/1200mm, heating plates: 2, connected load: 14kW, pressing force: approx. 65t, max. pressing height: 300mm, machine dimensions X/Y/Z: approx. 2600mm/1350mm/1800mm, weight: approx. 3300kg. An on-site inspection is possible.

CONTROLS   PLC SIEMENS S7 300 PRESS DESIGN   drive system: hydraulic PRESS FORCES   total force (nominal): 800 to PRESS TABLE   table surface (left-right): 2600 mm   table surface (front-back): 2000 mm   height above floor level: 540 mm SLIDE   stroke: 900 mm SLIDE (HYDR. PRESS)   approximation velocity max.: 460 mm/s   working velocity min.: 25 mm/s   working velocity max.: 44 mm/s   return velocity max.: 460 mm/s TOOL ASSEMBLY DIMENSIONS   shut height (stroke down, adjustment up), BDC: 1700 mm ELECTRICAL SPECIFICATIONS   total power consumption: 180 kW DIMENSIONS / WEIGHTS   total weight approx.: 95000 kg ATTACHMENTS (PRESSES)   press automation: yes   gripper transfer system: yes   acc. to actual accident protection ...

A fully automatic hot stamping press Oropress for gold and silver hot stamping is available. Press force: 5t, sliding table dimensions X/Y: 250mm/250mm, die dimensions X/Y: 120mm/200mm, max. operating temperature: 250°C. A rotary switch of the machine is missing and the adjustment is carried out using a screwdriver. One tension roller was repaired with a new flange bearing. Including foil feed unit. An on site inspection is possible.

Brand: Kremer Type: KR-7300WH Working pressure: 200 bar Temperature: 30°C to 110°C High-pressure hose: 10 meters of high-pressure hose Equipped with: suction hose for cleaning agent Boiler: diesel-fired Heat Recovery: 58 kW Capacity: 900 liters per hour Connection: 400 volts Electrical power: 7.3 kW Speed: 1450 rpm Weight: 128 kg Includes: high-pressure gun, high-pressure hose, water filter, brass coupling and manual Condition: unused, in the original packaging Auction-ID: A3-43506-447

Features: 400v connection Diesel tank Wheels High-pressure hose 10 meters with lance Pressure regulator Temperature controller Auction-ID: A1-40103-97

Brand: Kremer Type: KR-7300WH Working pressure: 200 bar Temperature: 30°C to 110°C High-pressure hose: 10 meters of high-pressure hose Equipped with: suction hose for cleaning agent Boiler: diesel-fired Heat Recovery: 58 kW Capacity: 900 liters per hour Connection: 400 volts Electrical power: 7.3 kW Speed: 1450 rpm Weight: 128 kg Includes: high-pressure gun, high-pressure hose, water filter, brass coupling and manual Condition: unused, in the original packaging Auction-ID: A3-43511-468

Equipped with open hose reel, 20 meter hose, spray gun and 2 spray lances. Auction-ID: A1-40134-344

Equipped with hot water with 700 liter buffer tank; adjustable temperature up to 90 °C; Stainless steel diesel fired burner system; max working pressure 250 bar; 2x LED work light; water tank; high-pressure hose length 17 meters; high-pressure spray lance; electric start; 15 hp 4-stroke petrol engine; 4 extra nozzles; venturi valve connection for adding chemical liquid; unused Auction-ID: A1-40134-350

Brand: Kremer Type: KR-7300WH Working pressure: 200 bar Temperature: 30°C to 110°C High-pressure hose: 10 meters of high-pressure hose Equipped with: suction hose for cleaning agent Boiler: diesel-fired Heat Recovery: 58 kW Capacity: 900 liters per hour Connection: 400 volts Electrical power: 7.3 kW Speed: 1450 rpm Weight: 128 kg Includes: high-pressure gun, high-pressure hose, water filter, brass coupling and manual Condition: unused, in the original packaging Auction-ID: A3-43515-468

Temperature range max.: 140 °C; capacity: 900 l/hr; power: 7.3 kW; connection: 400 V; own weight: 128 kg; overall size L: 1150 mm; overall size W: 620 mm; overall size H: 850 mm; description: unused in wooden box; 4460; Auction-ID: A1-45773-507

Temperature range max.: 140 °c; capacity: 900 l/hr; diesel-fired: yes; power: 7.3 kW; connection: 400 V; unused in wooden box; 4496; Auction-ID: A1-45773-242

Temperature range max.: 140 °C; capacity: 900 l/hr; power: 7.3 kW; connection: 400 V; own weight: 128 kg; overall size L: 1150 mm; overall size W: 620 mm; overall size H: 850 mm; description: unused in wooden box; 4460; Auction-ID: A1-45773-18

Temperature range max.: 140 °c; capacity: 900 l/hr; diesel-fired: yes; power: 7.3 kW; connection: 400 V; unused in wooden box; 4496; Auction-ID: A1-45773-241

Cat.-Nr. 11-370-2 new double jacket and insulated Volume: 2400 Litres - Parts in touch with product in AISI 316 – other parts in AISI 304 without Heating Jacket Material: Parts that come in touch with the product in V4A (AISI 316) – other parts in V2A (AISI 304) Max.Working Pressure. 0,49 bar Surface fully pickled, passivated and neutralised Insulation with Mineral Wool for Hot Water Tanks Thickness = 80 mm Standard Equipment: Manhole on the top Air Release and Pressure Valve in PVC Manhole inside oval 400 x 350 and Manhole outside rectangular for insulation jacket Sample Valve Level Indicator 24 mm Ladder Support Outlet Discharge with Outlet Pipe DN 50 Digital Thermometer Clear Outlet DN 50 Transport Hooks with Insert Heating Element 230/400V, 7,5 kW Diameter: 1350 mm Height: 3130 mm Cyl. Height: 2160 mm F ...

Cat. No. 11-3170 New without heating jacket - round standing on feet Medium-contact parts V4A (AISI 316) with electric screw-in heating 230/400 V, 7.5 kW Standard: Material: medium-contact parts V4A (AISI 316) - otherwise V2A (AISI 304) Operating pressure max 0.49 bar Container completely stained, passivated and neutralized Insulation made of mineral wool for hot water tanks thickness = 80 mm Standard: Manhole top DN 400 Ventilation and vent valve made of PVC Manhole inside oval 440 x 350 and manhole 500 x 430 outside rectangular for insulated container Test tap Stand display 24 mm Ladder bracket Residual drain with forward-drawn outlet pipe DN 50 with disc valve DN 50 with lid Digital thermometers Clear drain DN 50 with disc valve with lid Transport eyelets with electric screw-in heating, 230/400V, 7.5 kW Cat. No. Contents  ...

for the storage of hot water / firefighting water. Dimensions: 2.50 m = D - L = approx. 10.70 m The container is used, empty inside and professionally cleaned and is outside with a coat of bitumen / bitumen insulation provided. Light insulation damage caused by construction and transport may be available at the reservoir. Price from Söhrewald - free of charge-

Machine is in perfect condition. All mechanical, electric parts were overhauled or changed to completely new. Along with the machine we provide 1 set of equipment for a clients bottle and basic change parts for a 2 years production. Capacity: 22500 b/h 18 months guarantee.

1 of used hot-melt unit, make Nordson, type 3700-2BB36. Tank capacity 13.6 kg, melt rate 18.1 kg/hour. Suitable for 380-415/220-240V, 50/60Hz. With Pneumatic piston pump 21:1, non-recirculating manifold for 6 hoses witih standard filter, Multiscan controls for 6 hoses and guns. Hoses and guns NOT included. New 1990.

Make : Wolf Type: WLE-S-180 Built: 1993 Dimensions: 1.3 m x 2.2 m x 2.6 m (approx. WxLxH) Heating unit: 209 kW Burner : Gas burner Dry temperature: max. 80 degrees C Circulating air unit: 14,000 m3/h; 7.5 kW; 1435 rpm Location : Camp Herzogenaurach Sales price: € 2,990,- net, from location This plant is already on sale, similar we have in stock. We have complete painting booths, drying booths and spare parts for painting systems in stock, e.g. Aggregates, lights, filter ceilings, entrance gates, roller doors, gratings, air ducts, etc. Please contact us, tel. 0171-9508841.

1 used Nordson order head, type Mini Blue II SureBead, 230V / 100W, with solenoid valve and 40-degree connection, built in 2013. 10 pcs. available (intermediate sale reserved).

1 used Nordson 16 foot hose, Blue Series, 240V/504W. Built 2013. Nordson part number 2747976. 6 pieces available (intermediate sale reserved).

1 used Nordson 24 foot hose, Blue Series, 240V/760W. Built 2013. Nordson part number 274797. 6 pieces available (intermediate sale reserved).

Single Slab Reheat Furnace • Type: Walking Beam • Manufacturer: Davy • Capacity: 150 t/h • Inside Refractory Width: 8,35 m • Effective Length: 32,6 m • Slab Thickness: 160 mm • Slab Maximum Length: 7,5 m • Primary Fuel: mixed BFG and COG • Alternate Fuel: N°6 Fuel Oil • Commissioned in 1995 Water Descalers • Primary descaler at slab reheat furnace run out table • Front and back 3 Hi Rougher Mill descalers. • Finishing Mill descaler at run-in table. Water Descaling Pumps • Manufacturer: Union Pump Company • N° of Pumps: Two (one operating, one stand by.) • Power: 5.000 HP (3.730 kW) • Pump Speed: 4.500 rpm • Discharge Pressure: 127 barg (1.840 psig) Rougher Mill • Type: 3 Hi, one stand 22" x 34" x 100" Reversing Mill • Manufactured by Blaw-Knox in 1923. • Ma ...

Nordson 3100-2AA32; State as is; only checked for function; Ready. At this point we allow ourselves to note that all offered machines are in our unrestricted possession or access and are present in our warehouse. Visits and demonstrations are possible on request in our premises. We would also be pleased to inform you about our complete stock, as only part of our portfolio is presented here.

maximum format 1060 x 800 mm min. size 350 x 350 mm Speed 80 m / min. Paper thickness 105-500 grams Energy 101 kw Weight 8500 kg Mass 8860 x 2380 x 3000 mm

Hot water buffer tank with insulation Year of construction: 2011 Condition: Used Specifications Connections: 4 screw-ins for immersion sleeves: inner diameter 1/2" 2 flange connections: inner diameter 80 mm 1 filling neck: inner diameter 1 1/4" Metrics Height: 3,550 mm (boiler only) Diameter: 1,198 mm Circumference: 3,765 mm Volume: approx. 3,982 m³ Operating pressure: max. 4 bar Weight: approx. 500 - 600 kg Insulation: 160 mm The buffer tank has been reworked on the outside with rust protection and 2 coats of paint. Transport can be arranged through our house on request! Price: € 3,900.00 plus VAT ex Grunow site (Brandenburg) (Subject to changes and errors regarding technical data and prices!) In accordance with our terms and conditions, we would like to point out once again that cheques and bills of exchange cannot be accepted.