hot foil stamping used for sale

Heißfolienprägemaschine / Hot Foil Stamping GEBA 1/F-2

Dreimesserautomat / Three Knife Trimmer Wohlenberg FA 38 Baujahr / Year 1989 Format / Size max. 315 x 410mm Thicknes max. 100 mm Speed max. 3000 cycles per hour Automatischer Einlauf / Specification automatic feeding Bandauslage / Belt delivery

Heißfolienprägetiegel / Hot Foil Stamping Tiegel Heidelberg GTP Baujahr / Year 1966 - Serial-No. 63 613 Format / Size min. 85 x 102mm Format / Size max. 340 x 460mm Geschwindigkeit / Speed min. min. 1.500sph - max. 4.000sph Stanzkraft / Punching pressure 60T Gewicht / Weight approx. 2250kg Abmessungen / Dimensions 2,08 x 1,48 x 2,10m Komplett mit Zubehör und Schließrahmen / Complete with tools and accessories include frame

Prägepresse / Hot Foil Stamping Press

M. No.: 46131 Equipment / Additional information: Stamping surface with heating head: HKAC max. 100 x 125 mm // HKBC max. 140 x 230 mm Stamping pressure at 6,5 bar with: 1 Zylinder ca 400 daN (kp) // 2 Zylinder ca 800 daN (kp) Readjustable stroke, dep. on pressure producer: 0-40 mm / 0-100 mm Max. passage height without/with sliding table: 300 mm / 275 mm Readjustable foil advance: 0-230 mm Max. foil width: 140 mm Heating voltage: 220 V / 50 Hz Heating capacity with heating head: HKAC 540 W // HKBC 900 W Temperature measurement by means of: Fe-Ko Max. output, hourly cycles: ca 4000

with original HDM hot foil stamping device

with original HDM hot foil stamping device

Format : 73 x 104 cm (29”x 41”) Spiess feeder with pre-marge Front and side detection cells PC Control panel 3 x advances 2 x honeycombs straightened 2 x new honeycomb frames 2 x new heating units Air-conditioned electronic cabinet

Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm; -height: 1280 mm Main motor: 400/590 kW/rpm Press layout dimensions: 6300x8965 mm Total height: 11125 mm Height above floor level: 9150 mm Total weight: 626100 kg

NOTE additionally a new shaft Description Force , 4000 TN Slide stroke, mm 400 Number of continuous slide stroke, stroke / min 50 Closed height of stamping space mm 1000 Adjusting the table mm 15 Distance between columns in light,mm 1660 Drive power, kW 185 Table dimensions in plan mm: - From left to right in 1620 - Front-to-back in 1570 Dimensions in mm: - in the plan 6100 x 4710 - Height above floor level 6820 - Press height 8680 Weight, t 377

Kniehebelprägepresse - Embossing hot stamping press Hans Schilling HSM Serial-No. 18040 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Heißpräge - Kniehebelprägepresse - Embossing Hot Stamping Press Krause FNP Serial-No. 4798 Stamping size: 550 x 400 mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Eccentric shaft by drawing K04.038.842-22-402 for hot stamping press K04.038.842 (K8542), 1600T brand new in state stale from stock W 4675 kg

A hot stamping system is available for hot stamping the silver edge on instrument panels. Heating capacity: 5.6 kW, stamping force: 20 kN, max. pressure: 6 bar. Including laminar flow module Spetec Super Silent. Documentation available. On-site inspection is possible.

-Max pressure at the end of stroke – 4000 ton -Press stroke – 400 mm -Number of stroke – 50 per minute -Max distance of stroke from the table – 1400 mm -Dimensions of slider: 1320 x 1320 mm -Bed dimensions: 1120 x 1600 mm -Bed movement by height – 20 mm -Max pressure of upper ejector – 20 t -Max stroke of upper ejector – 65 mm -Max pressure of lower ejector – 40t -Max stroke of lower ejector – 80 mm -Main motor power – 225 kW -Main motor speed – 730 rpm -Total width — 6280 mm -Total depth – 4885 mm -Total height – 8870 mm -Height over the bed – 7315 mm -Total net weight – 280 092 kg

Pneumatische Heißprägemaschinen/Lifting Hot Stamping machineGierlichPE 500 - 2P Baujahr / Year 1985 - Serial-No. 7458 Druckkraft / Pressure 5 kN Prägefläche / Embossing surface 100mm x 133mm Einsatzhöhe / Insert height 0-260mm Ausladung / Projection 220mm Folienbreite / Foil width max. 110mm Folienrollen / Foil rolls Ø120mm Prägetemperatur / Embossing temperature 50°C - 400°C

Antike Kniehebelprägepresse / Antique Embossing Hot Stamping Press Karl Krause KHP Baujahr / Year ca. 1930 - Serial-No. 48090 Prägefläche / Embossing Size max. 340 x 430mm Beheizung mit Gas / Heating with Gas Wunderschön verarbeitete antike Kniehebelprägepresse  Beautifully crafted antique Embossing Hot Stamping Press

Built in 1993 semi-automatic hot stamping press Embossing format max. 125 x 280 mm electr. Drive 1 foil preference 1 heating plate automatic feed Unwinding device for round materials / cans Underframe Delivery date: immediately from stock Price on request. We supply and install worldwide.

Hot stamping hand lever press, embossing foils, silver gloss and gold luster among others are included Note: The operating hours are unknown. The entry 99999 hours is only pro forma and does not correspond to the actual hours

TECHNICAL DATA: Power consumption: 1 kW Working temperature: 470 °C Ideal for use on wood

TECHNICAL DATA: Power consumption: 2.5 kW Working temperature: 470 °C Operating pressure: 5 bar Ideal for use on wood

A fully automatic hot stamping press Oropress for gold and silver hot stamping is available. Press force: 5t, sliding table dimensions X/Y: 250mm/250mm, die dimensions X/Y: 120mm/200mm, max. operating temperature: 250°C. A rotary switch of the machine is missing and the adjustment is carried out using a screwdriver. One tension roller was repaired with a new flange bearing. Including foil feed unit. An on site inspection is possible.

KAMA TS 105 / HFS 105 Year 2007 Diecutting and Hotfoil Sheet size : 74 x 105 max. / 33 x 48 min. Cardboard thicknesss: 130 - 1500 g/m² (1.8mm) Max. pileheight feeder : 1150mm Max. pileheight delivery : 880 mm Features: Mabeg Feeder Digital control Sheet allignment KAMA HFS 105 hot foil unit

Hot stamping machine designed for applying logos, markings, or designs onto leather and shoe components using heat. Auction-ID: A7-46462-15

Used for applying numbers on materials using heat stamping. Auction-ID: A7-46462-17

Used for applying numbers on materials using heat stamping. Auction-ID: A7-46462-19

COMPLETELY WORSHOP REFURBISHED ! Min. size 350 x 500 mm / 920 x 1260 mm Speed of 5,000 c / h Quick clamping system in the stripping station Paper 80 g / m2 Cardboard max 2000 g / m2 16 heating zones Temperature 50 ° to 160 ° Autoplaten concept Stripping

Hot foil stamper, available now, fully workshop refurbished, ready to test • ELEVATED MACHINE Machine elevated 415 mm, included elevation of the steps • Step • Centerline for job quick change • Electronic device for sheet travel control • Air conditioning for the electrical cabinet • Gripper bars • Bobst-electronic for managing the machine • Motore principale con variatore di frequenza • Pianale porta-pila con leva per la correzione laterale manuale della pila durante la produzione • NON-STOP FEEDER MANUAL DEVICE • Adjustable lateral blowers with Centerline references • Suction unit with multiple adjusting • Safety system for lowering the pile try • Introduction table covered by antistatic steel stainless plate • Sheet synchronization adjustable during the machine is running for adapting feeder cycle to platin cycle • Feed belt slow-down device Ensures  ...

Converting Line GM 330 FB-D (Hot stamp + Screen print) Year of manufacture: 2018 Manufacturer: Grafisk Maskinfabrik Max. web width: 350 mm Min. web width: 50 mm Unwind diameter: max. 700 mm Rewind diameter: max. 600 mm - Vetaphone Corona - BST web edge control Hot foil stamping unit (flatbed) Speed: 6,000 stamps/h or 10-15 m/min Web width: 110 mm - 330 mm Dual foil unwind and rewind with a diameter of 250 mm Substrates: 50-500 μm Board thickness: 5-10 mm; 7 mm is standard Plate pressure: 30 tons Foil feed in transverse and longitudinal directions (rotating tower) Temperature range 80°-130° C Heat-up time approx. 20 min. Screen printing unit Speed 4000 print runs/h or 5-15 m/min. Web width 110 mm - 330 mm Frame size 660 mm x 500 mm Frame type 30 mm x 30 mm aluminum frame Printing area 330 mm (length) x 330 mm (width), Manufacturer: Grafisk Maskinfabrik, Substrates: 50-500 um

Technical details Manufacturer: Heidelberg Model: SBDZ Type: Cylinder die-cutting machine with hot foil system Max sheet size: 640 × 900 mm Min sheet size: 110 × 290 mm Hot foil system: Cavomit (installed 2005) Control: Servo-controlled system Application: Die cutting, creasing, and hot foil stamping of paperboard and printed materials YOM: 1972 / Refurbished: 2005 Auction-ID: A7-46679-1

After cooking stove, thermal oil, Formcook, frying line (CFS, GEA, Koppens, Alco, Stork) - continuous grilling line - Total length outside: 6 m - Total width: approx. 1.300 mm - Height of the gallows: 1.200 mm - Gallows for chain hoist - 5 floors above each other - Conveyor belt of wire belt: 600 / 2,35 / 7 / 12,7 - Double-walled floor and hood, isolated

After cooking stove, thermal oil, Formcook, frying line (CFS, GEA, Koppens, Alco, Stork) - serial: Sprematec - length: approx. 10 m - width: 1350 mm inside / 1518 mm outdoor - heated thermal oil - year: 10/2003

1070 x 1480 mm

1 AUTEFA loose stock/flock stampfing press type 6.62 for stamping lose flock into materila carriers for dyeing / bleaching machines, with 2 stampfing arms with motorized rotational carrier support . complete with electrical panel

Blumer MCB III - label punching Technical Details · Max format : 700 x 1000 mm, · Min punched format : 10x10 mm, · Max punched format (non stackable)250 x 700 mm, · Max label format–stackable 150x 150mm, · Stack height : approx 50 / 80mm, · Punching pressure : 20tons, · Punching tool height:30 – 80mm. Additional Information · Delivery time IMMEDIATELY · Typ: MCB III · Year of man. 1988 · Condition: excelent · Located: Zagreb, Croatia Description · BLUMER MCB 3.1 PUNCHING MACHINE. The MCB 3.1 can punch any formats from paper, plastic, textiles, aluminium foil etc with fast program speed and high precision. Programming is via a freely programmable CNC, Storage capacity : approx 100 programs containing about 200 label positions each , numerically programmable. Machi ...

Blumer MCB III - label punching Technical Details · Max format : 700 x 1000 mm, · Min punched format : 10x10 mm, · Max punched format (non stackable)250 x 700 mm, · Max label format–stackable 150x 150mm, · Stack height : approx 50 / 80mm, · Punching pressure : 20tons, · Punching tool height:30 – 80mm. Additional Information · Delivery time IMMEDIATELY · Typ: MCB III · Year of man. 1978 · Condition: excelent · Located: Zagreb, Croatia Description · BLUMER MCB 3.1 PUNCHING MACHINE. The MCB 3.1 can punch any formats from paper, plastic, textiles, aluminium foil etc with fast program speed and high precision. Programming is via a freely programmable CNC, Storage capacity : approx 100 programs containing about 200 label positions each , numerically programmable. Machi ...

(side-front moving table) Nominal force: 1000 ton Slide stroke: 400 mm Continuous slide strokes per 1 min: 20 Single slide strokes per 1 min: 16 Shut height: 1060 mm Slide adjustment: 320 mm Table dimensions: 3150x1800 mm Slide dim., front-back: 1700 mm Window H 1500 x W 1900 mm Hydro pneumatic cushion in table clamping force at P = 0.42 MPa (P = 4.2 kg / cm2), kN 2000 ejection force P = 0.45 MPa (P = 4.5 kg / cm2), kN 200 Main-drive electric motor power: 132 kW DIMENSIONS: 5150x4700x11400 H floor7830 mm WEIGHT:193 ton

effort 250 ton stroke 315 mm slide adjustment 160 mm distance slide- table 800 mm die height 555 slide 620x950 mm table 800x1180 mm 28 kW Total weight 25t

Maximum force ton-force 400 Slider stroke length mm 250 Slider stroke length to lower position mm 12 Slider strokes per minute 25 Number of single turn-on 19 Maximum distance between table and slider (in lower position of slider) mm 510 Adjustment mm 160 The sizes of a under-forginig plate mm 1000 Table overall dimensions: mm ·from front to rear 1000 ·from left to right 1000 The sizes of an aperture in a table mm 630 Slider overall dimensions mm 800 x 800 window dimensions in cheeks mm 600 Total power of electric motors kW 43,3 Press overall dimensions mm ·length 3470 ·width 3140 ·height 5940 Press weight without hydropneumatic pillow kg 31 400

COLOMBO AGOSTINO 225.400 coil stamping and punching line was built in 2006 in Italy by Colombo Agostino S.p.A. Its extensive machining capabilities and high reliability make it an excellent choice for series production of components, such as washing machine parts or automotive parts. The production process is fully automatic, thanks to a high-speed feeding system. It unwinds the sheet metal from the coil towards the work station, which features precision tools operating at a maximum force of 400 tonnes. The monolithic design of the machine further ensures high durability and stress-free operation. The COLOMBO AGOSTINO coil-fed punching machine weighs 75000 kg. The coil punching line is complete and consists of the following machines: – 400 t eccentric press: COLOMBO AGOSTINO – sheet metal decoiler: DEF CT 3/128 – coil lift table – sheet metal straightener RA 3000/4-8/120 A ...

Maximum force ton-force 400 Slider stroke length mm 250 Number of courses of a slider per minute 25 Maximum distance between table and slider (in lower position of slider) mm 670 Table overall dimensions: mm - from front to rear 1000 - from left to right 1000 Main electric motor power kW 40 Press overall dimensions mm - length 3410 - width 3140 - height 5930 Press weight kg 30 600

Manufacturer Erfurt Pressen Machine type Leinhaas Technology Country of origin Germany (BRD) Machine data Parameter Value Unit / Notes Max. press force 4500 kN Stroke rate (continuous) min. 15 strokes/min Max. stroke rate (tool designed for) 75 strokes/min Ram stroke 3 – 200 mm Ram adjustment 120 mm Installation height (min.) 600 mm Max. installation height 670 mm Dimensions of press table Press table length 2000 mm Press table width 1250 mm T-slots (press table) DIN 650 – 28 H12 Number of T-slots (table) 11 pcs Distance between T-slots 150 mm Dimensions of press ram Slide length 2000 mm Slide width 1200 mm T-slots (slide) DIN 650 – 22 H12 Number of T-slots (slide) 13 pcs Distance between T-slots 150 mm Press frame opening Side opening 900 mm Front opening 2200 mm Tool clamping Tool clamping height (upper tool) 80 mm Tool clamping h ...

Printing machine, embossing machine, stamping machine -without function, control: defective -pneumatic-hydraulic press - Stroke: 50mm - clearance between columns: 850 mm -Table surface: 400 x 370 mm -Dimensions: 1285/590/H1820 mm -Weight: 416 kg

Die holder, notching tool, punching tool, punch, punching die, punching die, punching die, round die -Manufacturer: Mubea, punching die round die Ø 75 mm -Type: Mubea 75 1 5 -Total dimensions: Ø 150 x 40 mm -Weight: 3,9 kg