131,504 used machines on RESALE, but how to find them? Machine Search
used
Technical DataFeed rate longitudinal/transverse/vertical40000/40000/40000 mm/minRapid traverse longitudinal/transverse/vertical40/40/40 m/minWorking area 1Longitudinal735 mmCross650 mmVertical560 mmGeneralUniversal Machining Centre in monoBLOCK construction; Control: CELOS X with HEIDENHAIN TNC7 Tool changerTool changer planevertical Type of gripperDouble gripper Number of tools60 Max. tool length315 mmMax. tool diameter with occupied adjacent pockets80 mmMax. tool dia. with free neighbouring pockets160 mmFloor space/WeightWeight approx.14500 KgNC swivel rotary tableTable surface Ø650 mmCentre bore 32 mmMaximum load (table centre) 600 KgRotation Speed 5. Axis 20 rpm5. Axes (swivelling range) +/- 120 degree4. Axes (swivelling range) 360 x 0,001 degreeRotation speed max.4. Axis 40 rpmDistance between T-Slots 63 mmNumber of Slots 9Slot width 14 mmIntegrated motor spindle speedMASTER®Drive ...
CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets with ...
CNC - Sheet Metal Parts - Roll Straightening Machine for plane straightening and relaxing of thermally cut sheet metal parts, for stamped parts, for sheet metal parts that have been cut to size with the sheet shear. Our roller straightening machine is a purely electric machine, not hydraulics, the electronically controlled servo motors enable automatic CNC – controlled face straightening in the continuous process. CNC – controlled precision sheet metal parts roll straightening machine for sheets from 0.7 mm to a maximum of 14 mm sheet thickness at 500 mm sheet width Largest sheet width 1,500 mm Guideline power over the full width - - Steel sheet quality SR235 from 0.7 mm to 10 mm - Stainless steel sheet from 1 mm to 6 mm Planning by - 19 piece straightening rollers with Ø 50 mm 21 pieces of intermediate rollers with Ø 30 mm 13 pieces of support roller sets with ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
I sell a 4-side brush machine suitable for windows, turrets, tables, etc. Futura MS120 Y1 X2, built in 2005 Working width 1200mm Working height 200mm Total weight 2500kg Configuration: Side grinding heads left - right H.170mm 2 underheads left - right nylon B.140mm Oscillating top head B.260mm Large grinding heads top - bottom B.1150mm Machine together with all the heads on the picture. Available the same.
used
GeneralUniversal milling and turning machining centre with duoBLOCK construction; Control: CELOS with Heidenhain TNC 640 Technical DataFeed rate longitudinal/transverse/vertical60000/60000/60000 mm/minRapid traverse longitudinal/transverse/vertical60/60/60 m/minWorking area 1Longitudinal800 mmCross1050 mmVertical850 mmTool changerApplicationUniversal Type of magazineWheel Tool changer planehorizontal Type of gripperDouble gripper Number of tools123 Uni milling head with controlled B axis HSK-A 63Universal milling head with controlled B axis HSK-A 63 Continuously positioning universal milling head (B axis) with integrated motor spindle for 5 axes positioning and simultaneous machiningNC mill-turn table with palletNC mill-turn table with pallet number of T-slots: - 1x cross slot 14 H7 / 0.55 H7 - 12x star slots 14 H11 / 0.55 H11 / 22.5° max. table speed milling operation: 30 rpm turning o ...
used
GeneralUniversal milling and turning machining centre with duoBLOCK construction; Control: CELOS X with Siemens SINUMERIK ONE Technical DataFeed rate longitudinal/transverse/vertical60000/60000/60000 mm/minRapid traverse longitudinal/transverse/vertical60/60/60 m/minWorking area 1Longitudinal800 mmCross1050 mmVertical850 mmTool changerApplicationUniversal Type of magazineWheel Tool changer planehorizontal Type of gripperDouble gripper Number of tools123 Uni milling head with controlled B axis HSK-A 63Universal milling head with controlled B axis HSK-A 63 Continuously positioning universal milling head (B axis) with integrated motor spindle for 5 axes positioning and simultaneous machiningNC mill-turn table with palletNC mill-turn table with pallet number of T-slots: - 1x cross slot 14 H7 / 0.55 H7 - 12x star slots 14 H11 / 0.55 H11 / 22.5° max. table speed milling operation: 30 rpm turn ...
Key data: 400 mm
S375G SAMPUTENSILI "CNC" Horizontal Gear Profile Grinding Machine, suitable for the precision grinding of external spur and helical gears and shafts, as well as internal spur and helical gears and splines. The machine has the added capability of grinding worms, rotors, and other screw-type workpieces of similar profile up to 14.76” (375mm) which was factory OEM standard - but delivered at 15.74" (400mm) diameter, and 34.25” (870mm) in length. The machine is also equipped with the optional” on-board CNC” dressing feature, and the on-board CNC” gear inspection system-feature. Serial No. 2376 (New in 2007) This is a first-class, highly versatile gear grinding machine, in superlative” condition throughout, which may be inspected, in running service, at our customer’s plant facility, by appointment. -The machine would require acquisition & adaptation of an appropria ...
used
May SS80 U Machine can be visited by arrangement under power
MEP Multimatic SA8, year of construction 1995 Straightening and cutting system for reinforcing steel, fully automatic, complete functional system, immediately available Plant still in operation and can be demonstrated.
AUERBACH AX 5 B CNC bed milling machine was built in 2009 in Germany by Auerbach Maschinenfabrik GmbH. It is an extremely efficient machine designed for even the most demanding production challenges. The AUERBACH AX5 B enables the machining of large, heavy workpieces that are used, e.g. in the aerospace and automotive industry. The machining process is performed fully automatically on the rotary table by means of a 5-axis swivel workhead. This solution enables comprehensive machining of workpieces in a single work cycle, without the need for repositioning them. The workhead is equipped with an electro-spindle rotating at a maximum speed of 12000 rpm. It provides the excellent dynamics required for both roughing and finishing operations. The cutting tools, on the other hand, are continuously cooled to increase their overall service life. The AUERBACH AX 5B CNC machining center is offered ...
Bread packaging machine Hartmann Automat GBK 220 -Sliced bread packaging machine Hartmann -Model Automat GBK 220 -Weight 1600 kg -Year of construction 1999
Rogers 300 HYD Knife Roll Grinder Model: 300 HYD Size 102 Year of arrival at the plant: 1961 Space used by the machine: 7 x 2 x 1,8m Worktable dimensions: 2600 x 250,50 mm. Longitudinal table travel (stroke): 3000 mm. Magnetic system of the table: EML 15 - 115 Volts - 13 Amp - 1500 Watts. Longitudinal slide feed: 0 - 28 m/min. Cross travel without abrasive wheel: 200 mm. Cross travel with new abrasive wheel: 92 mm. Vertical Capacity: 200 mm. Abrasive wheel: Ring abrasive wheel, 26" outer dia., made up of 10 segments type 53 (S/G FLAT RS-801-B) of 6.1/2 "x 2 "x6". Each segment must indicate the maximum RPM for the ring. Abrasive wheel head speed: 560 Rpm. Cooling tank capacity: 259 liters
Bottle washing machine, Fabr. Krones, type: Lavatec KESK 245/17-120, control range 4,000 - 11,000 fl/h, for bottles with max Ø 105mm, built in 2002, Eind machine, with 180 rows of 17 bottles/row each, with pre-soft water and lye, main liquor with immersion switch and after-liquor spraying, 3 water sprays hot, cold and fresh water in stock from May!
M. No.: 167 Format (cm): 58 Equipment / Additional information: 1xreserve knife Very good condition // tested, checked and revised
Injection Unit Screw Diameter: Ø 50 Injection Volume: approx. 392 cm³ Injection Pressure: up to 2,100 bar Injection Rate: approx. 200 cm³/s Plasticizing Capacity: approx. 30 g/s (PS) Screw L/D Ratio: 22:1 Nozzle Contact Force: 50 kN Clamping Unit Clamping Force: 1,900 kN (190 t) Clamping System: Zhafir Zeres all-electric with servo-hydraulic auxiliaries Platen Size (H × V): approx. 770 × 720 mm Mould Opening Stroke: 450 mm Max. Daylight Opening: approx. 900 mm Min. Mould Height: 200 mm Ejector Stroke: 150 mm Ejector Force (fwd / back): 40 / 30 kN Drive & Control Drive Type: Hybrid electric / servo-hydraulic (Zeres series) Connected Load: 45 kW Full Load Current: 76 A Short Circuit Current: 25 kA Power Supply: 400 V / 50 Hz / 3-phase Control System: SIGMATEK CNC-based control with Zhafir HMI touchscreen Equipment / Features Drive ...
REF-0 MANZINI (COMACO) CAN SEAMER FOR 3KG CANS Automatic can seamer manufactured by Manzini (Comaco) Model: A-350 Can size: 3kg Fitted with 3 seaming heads Power: 12HP Dimensions: 1,800mm width, 2,500mm length, 2,600mm height. Optional: 15-valve vacuum filling system for 3kg cans (vacuum pump included). Filling system dimensions: width 2,100mm, length 1,200mm, height 2,400mm.
Continuous drilling rig Biesse Techno Logic Masch. No 873/90 Position 1: Loader BIESSE-TECHNO LOGIC Item 2: Transfer BIESSE-TECHNO LOGIC Item 3: Transfer BIESSE-TECHNO LOGIC Item 5: Continuous drilling machine BIESSE-TECHNO LOGIC Item 6: BIESSE-TECHNO LOGIC horizontal continuous drilling rig Item 7: Transfer BIESSE-TECHNO LOGIC Item 8: Transfer BIESSE-TECHNO LOGIC Position 9: Brushing machine BIESSE-TECHNO LOGIC Item 10: Unloader BIESSE-TECHNO LOGIC Weight approx. 4 to L x W x H: 6.0 x 2.4 x 2.5 m Year of construction 1990 Dismantling by buyer The plant is in good condition, ready for operation Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 Fax: 0041 62 966 21 12
SCM st 1g Format circular saw milling machine Format sliding table in 1.2m Cutting height: 67mm 90° 40mm 45° Auslegertich kpl. Cutting width 700mm Saw blade: swivel 45°, max.250mm 1.8KW 2 motors 400V 50HZ Milling machine: rigid 90° Milling machine rpm: Speeds: 5000/7500 rpm. Milling stop max tool diameter max. 160mm Suction pipe 60 - 120mm Weight 190kg Eccentric tensioner G&STÜ-5501048
Viewing by appointment Auction-ID: A1-43890-37
Travel distances: 350 x 250 x 315 mm [ X x Y x Z ] Table size X: 576 mm Table size Y: 400 mm workpiece weight: 500 kg C-axis Pinole recording: EROWA
Kemper Soft-Star dough dividing and warp knitting machine Head machine Kemper Soft-Star 6-row dough part and automatic knitting machine with plastic funnel. The maximum hourly output of the machine is 2400 pieces per row and for our machine a total of 14,400 pieces per hour. The clock frequency is 40 strokes per minute. The operating side is in the direction of travel on the left side. The active range of the active drum is between 50 and 60 grams. - 6 rows - with plastic hopper - with Siemens Touch Panel control - Year of construction 09/2004 Electrical data Operating voltage: 400/230 Volt 50Hz Control voltage: 24 Volt DC Rated current: approx. 4kW
Travel: 825 x 680 x 405 mm [ X x Y x Z ] Table size X: 1200 mm Table size Y: 850 mm workpiece weight: 3000 kg Electrode changer: 50 - fold Generator POCON 60 Pinole recording: EROWA Heavy Duty Adapter O-Module Halogen lamp
WALDRICH SEIGEN WST IV H80 X 12000 ROLL GRINDER YEAR: 1981 / INSTALLED 1982 MAXIMUM GRINDING DIAMETER: 78” ( 1981.2 mm) WITH 32” (812.8 mm) DIAMETER WHEEL MAX DIAMETER CAPABILITY: 2500mm DISTANCE BETWEEN CENTERS: 472.40” (12000mm) MAXIMUM WORKPIECE WEIGHT: 176000 lbs. (80t) WHEEL OD MAXIMUM: 32.00” WHEEL WIDTH MAXIMUM: 4.00” WHEEL ID: 12.00” WHEEL SPINDLE POWER: 27 - 59/59 HP WHEEL DRESSER: BED MOUNTED ROLL WHEELHEAD TRAVEL: 25.60” TABLE TRAVEL: (WHEEL HEAD TRAVEL) 488.40”( 12405 mm) TABLE SPEED: (WHEELHEAD SPEED) 157.5 in/min (4000 mm/min) WHEEL SPINDLE SPEED: 450 - 1800 RPM Infinitely Variable WORKHEAD POWER: 1.9 - 59/59 HP WORKHEAD SPEED: .5 - 300 RPM WAYS: CAST IRON FULL HYDROSTATIC SLUDGE CONVEYOR: NONE COOLANT: YES FILTRATION SYSTEM: COMBINATION 2 CARTRIDGE AND FABRIC FILTER WAY COVERS: METAL TELESCOPIC POWER 3PHASE / 50-60 Hz / 200 - 50 ...
Injection Unit Screw Diameter: Ø 65 Injection Volume: approx. 1,075 cm³ Injection Pressure: up to 1,750 bar Injection Rate: approx. 400 cm³/s Plasticizing Capacity: approx. 85 g/s (PS) Nozzle Contact Force: 110 kN Clamping Unit Clamping Force: 5,500 kN (550 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,350 × 1,300 mm Mould Opening Stroke: 850 mm Max. Daylight Opening: approx. 1,450 mm Min. Mould Height: 400 mm Ejector Stroke: 220 mm Ejector Force (fwd / back): 95 / 65 kN Drive & Control Drive Type: Hydraulic (pre-ecodrive generation) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 45 kW Total Installed Power: approx. 65 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL EC88 digital control panel Equipment / Features Clamping System: Robust two-platen design for hi ...
Injection Unit Engine not working Screw Diameter: 65 Ø Injection Volume: approx. 1,025 cm³ Injection Pressure: up to 1,800 bar Injection Rate: approx. 450 cm³/s Plasticizing Capacity: approx. 80 g/s (PS) Nozzle Contact Force: 100 kN Clamping Unit Clamping Force: 5,000 kN (500 t) Clamping System: ENGEL Duo two-platen design Platen Size (H × V): approx. 1,300 × 1,200 mm Mould Opening Stroke: 800 mm Max. Daylight Opening: approx. 1,400 mm Min. Mould Height: 400 mm Ejector Stroke: 200 mm Ejector Force (fwd / back): 90 / 60 kN Drive & Control Drive Type: Servo-hydraulic (ecodrive inside) Hydraulic System Pressure: up to 160 bar Pump Motor Power: 37 kW Total Installed Power: approx. 55 kW Power Supply: 400 V / 50 Hz / 3-phase Control System: ENGEL CC300 touchscreen control Equipment / Features Clamping System: Two-platen design f ...
Label book printing machine, 4 colors, 3 colors, 2 colors or 1 color, punching unit, 2 embossing plates, various mounting plates, laminators, UV dryers, dispensers, slitter rewinders, scanner camera, in good condition, immediately available
MORI SEIKI NT6600 CNC INTEGRATED MILL TURN CENTER WITH LIVE MILLING MAXIMUM SWING OVER BED: 42" MAXIMUM WORK PIECE DIAMETER: 42" MAXIMUM WORK PIECE LENGTH: 239" MAXIMUM BAR DIAMETER: 6.4" SPINDLE BORE: 7" X AXIS TRAVEL: 41" Y AXIS TRAVEL: 26" Z AXIS TRAVEL: 242" B AXIS: +/- 120 DEG. MAIN SPINDLE SPEED: 1500 RPM MAIN SPINDLE MOTOR: 40 HP MILLING SPINDLE SPEED: 8000 RPM MILLING SPINDLE MOTOR: 40 HP ELECTRICS: 220V/3P/60Hz/216A OAD (APPROXIMATE): 490" X 182" X 169" HIGH WEIGHT (APPROXIMATE): 120,560 LBS. EQUIPPED WITH: C AXIS YAXIS B AXIS LIVE TOOLING/MILLING 20" CHUCK FS-31iA5 CNC CONTROL 140 POSITION AUTOMATIC TOOL CHANGER PROGRAMMABLE TAILSTOCK COOLANT THROUGH SPINDLE (HIGH PRESSURE) CHIP CONVEYOR Additional Control Options: Automatic Power Shut-Off MAPPS 4 System Part Program Storage: 8mb Stored Programs: 1000 Remote Communication Function ATA Flash M ...
Arm length: 1600 mm Drilling capacity in steel: Ø 50 mm Tapping in steel: M50 x 1.5 mm Spindle holder: MK 5 Spindle speeds: 28 - 2500 rpm. Spindle feed: 0.05 - 2 mm/rev Spindle stroke: 310 mm Spindle -> slab: 1500 mm max. Tension throwers; 1000 x 750 mm Clamping flat floor plate: 1820 x 986 mm Complete with: - Kuhlanlage - Operating instructions Spindle motor: 4 kW Country of origin: Czech Republic Machine Weight: 4300 kg Machine LxWxH: 3250 x 1120 x 3400 mm
Operation has not been tested. Auction-ID: A1-41994-95
Back punching machine Schmedt Präcut HHS 65; good condition; cleaned and tested; Block height max.350mm; Block thickness max.90mm; 3 replacement knives. Book block spine machine Schmedt Präcut HHS 65; good condition; cleaned and checked; max.block hight 350mm; max.block thikness 90mm; three knifes.
- Pallet feeder T 1020 FP 112 - 1. Station T1020-1-1020/6 buckles - 2. Station T800-M-2-88/6 buckles - Z2 mobile cross fold station - DESTA FSA 1000 delivery (1996)
Injection Unit Screw Diameter: Ø 70 Injection Volume: 1,239 cm³ Injection Pressure: up to 2,000 bar Injection Rate: approx. 500 cm³/s Plasticizing Capacity: approx. 95 g/s (PS) Screw L/D Ratio: 22:1 Nozzle Contact Force: 120 kN Clamping Unit Clamping Force: 4,500 kN (450 t) Clamping System: Two-platen design (Jupiter II series) Platen Size (H × V): approx. 1,140 × 1,040 mm Mould Opening Stroke: 950 mm Max. Daylight Opening: approx. 1,650 mm Min. Mould Height: 400 mm Ejector Stroke: 200 mm Ejector Force (fwd / back): 100 / 70 kN Drive & Control Drive Type: Servo-hydraulic system Main Motor Power: 62 kW Full Load Current: 104 A Short Circuit Rating: 25 kA Power Supply: 400 V / 50 Hz / 3-phase Control System: Haitian KEBA touchscreen control Equipment / Features Clamping Concept: Two-platen system for space efficiency and ...
Label book printing machine Labelmen PW180DLU, YOC 1996, 4 colors, punching unit, embossing device, various mounting plates, laminators, UV dryers, dispensers, Slitten rewinders, in good condition, immediately Available If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.
Folding machine MBO T49/4, machine number 83067246, 4 pockets + delivery, flat stack feeder, counter, in good condition, immediately available If you are interested, we will also be happy to inform you about other machines in our company. You are welcome to visit the machine in our house by prior appointment.
maximum number of results exceeded
please refine your search
10 € 
