high used for sale

Vertical Multistage High Pressure Centrifugal Pump GRUNDFOSNome pump, but part of the magnetic coupling has been dismantled. Type CRN 10-09 MP-FGJ GI-Vyear approx. 2012Flow rate at 7.2 bar: max. 10 m3/hDischarge height: max. 91.8 metersGrid connection: 400 volts, 50 HzPower: 3 kW- pump structure in 9 stages- made of stainless steel 1.4401- The pump in mint condition was used as a spare parts dispenser, but there are several new pump chambers- part of the magnetic coupling is missingsuitable for drinking water supply, irrigation

High-current EMC filter SCHAFFNER type FS 20364-1200-993 phases, 3 x AC ballast, mains connection module, mains filterInput voltage: 3 x 400 VACEinput frequency: 50 / 60 Hz.Nominal current: 3 x 1200 AAndimension W x H x D: 135 x 260 x 235 mmWeight: 27.5 Kgvery good condition, from stock liquidation, unused2 pieces available, price per piece; used

Quick-opening milling spindle HENNINGER type 814 / 5131 / 1:5 / 15000speed max. 15000 rpm at 70% EDratio ratio 1:5Power transmission up to approx. 2.5 kWProduct dimension 110 mm (machine spindle to clamping nutTool holder MK4 with tightening thread M16Collets type OZ16 6 / 8 / 9 / 10 / 11 / 12 / 12.5 / 13 / 14 mmWeight 6.5 kgGood condition; used

Klaaßen SDM15-5 turning machining centre, The top lathe we offer has the following in the basic configuration Technical parameters: ▪ SDM 4-5 CNC 4-Panel Bed Precision Lathe - Z-travel (slide longitudinal)= 5,000 mm (6,000 with TAE3) X-travel (face slide transverse)= 1,000 mm Y-axis (vertical movement)= 350 mm Maximum workpiece Ø = 1,500 mm Circulation diameter over face slide = 1,500 mm - Center width = 4,500 mm (5,500 with TAE3) ▪ CNC machine designed as a 4-lane tip lathe with full drive-over of the Bezels and superstructures - - - Cross slides and face slides restrict the diameter range by lateral arrangement on the lathe bed. As a result, there is no accompanying Diameter restriction above the face slide/tool carrier. Cross slide unit can be fully attached to the steady rests, HSSL and tailstock. This significantly reduces the set-u ...

MÜGA high-speed drilling-milling centre TYPE: S 3030 with 2-fold pallet changer incl. chip conveyor (similar to FANUC or BROTHER) Control: MITSUBISHI M70 Travel: X/Y/Z: 300 x 250 x 250 mm Spindle speed: 60 – 10,000 rpm. Motor power: 100//30% ED 2.2/3.7 kW Star turret: 12-speed Tool change time: 1.6 sec. Chip-to-chip time: 2.5 sec. Tool holder: BT 30 - 45° 2-fold pallet table: LxW: 400 x 250 mm Chip conveyor ejecting backwards Rapid traverse: X/Y/Z: 48/48/60 m/min. Installation area: L x W x H: 2690 x 1570 x 2370 mm Weight: 3300 kg Total connected load: 11.5 kW Description: The machine is suitable due to the 2-fold pallet system, as well as the high rapid traverses and fast chip-to-chip time for series part production. From 2011 to 2020, it was used in single-shift operation exclusively for ALU machining. There is no hour meter. The machine is still un ...

Perconta Contomat High Performance Self-Service Coin Settlement Terminal Tomatoes are taking over more and more routine tasks from bank employees. The trend that has set standards with automatic cash dispensing and the printing of account statements continues in coin processing with the Contomat. If you are looking for a solution for the customer-oriented deposit of hard change, you are well served with the Contomat self-service terminal. You can find more coin settlement terminals in other sizes - new and used - in our shop! International shipping costs on request!

Number of pallets approx. 3108 pieces • 4 types ( TYPE A, TYPE B, TYPE C1, TYPE C2) pallets. You can see below each one type height , length, weight. • Weight : Type A pallet = 1150 kg, TYPE B: 1150 kg, Type C1: 2000 kg, Type C2 : 1300 kg. • Number of pallets : Type A and B : 1888 pcs, Type C1 : 1004 pcs, Type C2 : 216 pcs, Total 3108 pieces

Mazzoni high-performance guillotine type cutter with its own conveyor Dimensions: Mouth width 550 mm Conveyor width 1000 mm Conveyor belt width 600 mm Total length 3000 mm

Offer 25380 Specifications: - Drilling capacity in steel ST 60 40 mm - Drilling capacity in steel ST 60 50 mm - Threading in steel ST 60 to M 42 - Drilling spindle holder MK 4 - Drilling spindle stroke 200 mm - Drilling spindle speeds infinitely adjustable 40 – 1100 rpm - Right - Counterclockwise rotation - 3 feeds 0.1; 0,16; 0.25 mm/rev - Projection 350 mm - Max distance drilling spindle – table / base plate 790 / 1210 mm - Table with 2 T-slots 630 x 540 mm Height adjustable via rack with hand crank - Drive 400 V / 1.6 / 2.9 kW - Space requirement approx. W 600 x H 2050 x D 980 mm - Weight approx. 650 kg - with: - Tapping device - Keyless chuck 1-13 mm - Emergency stop button -Lighting - Coolant device

A total of 10 deionization devices Keyence are available. Ion generation: +/-7000V, ion balance: +/-30V, max. effective range: approx. 3000mm, working distance range: 50mm-2000mm, electrode material: tungsten, applications: plastics/films/coating/electronics/packaging. Documentation available. An on-site inspection is possible.

Offer 25319 Specifications: - Drilling capacity in steel ST 60 35 mm - Drilling spindle holder MK 4 - Drilling spindle stroke 160 mm - Drilling spindle speeds 65 - 3250 rpm - 3 feeds 0.1 / 0.2 / 0.3 mm/rev - Projection 320 mm - Max. distance table - drilling spindle 560 mm - Table with 2 T-slots 500 x 420 mm - Height adjustable via rack with hand crank - Table left + right tiltable - Drive 400 V / 1.5 kW - Space requirement approx. W 550 x H 2200 x D 900 mm - Weight approx. 550 kg - with: - Right – Counterclockwise - Coolant device -Lighting

Press capacity: 63 ton Ram stroke adjustable: 8 - 60 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 300 mm Table surface area : 810 x 550 mm Slide area: 700 x 420 mm Hole in table: 550 x 140 mm Distance between oil tray: 700 mm Table height over floor: 920 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 8 ton Dimensions L x W x H: 2935 x 1170 x 3000 mm Main Motor: 11 kW

Air Pressure: 40 bar // Delivery Rate: 1630 m³/h

GUK FA 21/4 S2 SVA/730 stand-alone leaflet folding machine, 4 folding pockets, sheet format unfolded: min. 60 x 90 mm, max. 215 x 320 mm, smallest folding 15 mm, recommended paper weight 50-70 g/m², automatic drum suction feeder SVA/730, PCE barcode reader, double sheet control, output up to 460 folds/min., infinitely variable drive, electrical connection 400V/3Ph/50Hz, rated power consumption 1.76 kW, machine footprint approx. 1650 x 1075 mm (LxW), machine height approx. 1470 mm, machine net weight approx. 300 kg, machine in mobile version on wheels

The scope of delivery includes: 01x Rear wall grille, used Material colour: yellow Overall width: approx. 2,740 mm Total height: approx. 1,100 mm Mesh size: approx. 50 x 50 mm Frame profile size: approx. 40 x 40 x 4 mm Wire thickness: approx. 3.0 mm Weight | Pcs.: approx. 26.84 kg Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. Any additional transport or shipment of this item is associated with additional costs, which can be requested separately depending on the delivery location or scope of delivery.

USED VERTICAL MIXER, 24 m3 capacity, total height approx 5.400 mm including transmission group + cyclon, max Ø 2.800 mm., constructed in painted electro-welded carbon steel., inner auger diam.350 mm., lower loading hopper with safety grid and sampling shutter,, complete with anti-dust cover, mm.600x500, pulley and belt transmission, protected by carters, electric voltage: 400 V, 50 Hz,, conditions: good working conditions, availability: immediate, width: 2800 mm. special transport

Air Pressure: 40 bar // Delivery Rate: 950 m³/h

Dynajet 1000 me, used, blue Operating pressure: 1000 bar, Flow rate: 17 l/min, Drive: electric 35 kW, 400 volts, 63 A, Operating hours: approx.: 427 h, Trolly, incl. gun, 10 m HD hose, 15° flat spray nozzle,

A high-pressure pump BFT with Rexroth and VEM components is available. Pressure: approx. 4000bar, motor power: approx. 37kW. An on-site inspection is possible.

CHIRON FZ08 KS Magnum High Speed Plus (HSP) High-Speed Machining Center (HSP) TECHNICAL FEATURES: Year: 2006 NC Type: FANUC 18i-MB5 Number of axes: 7 X-axis travel: 450 [mm] Y-axis travel: 270 [mm] Z-axis travel: 310 [mm] X, Y and Z fast travel speed: 75000 [mm/min] Maximum diameter in bar turning spindle: 32 [mm] Maximum speed Turning spindle: 8000 [rpm] Maximum power turning spindle: 12 [kW] A-axis angular travel: 360 [°] A-axis indexing accuracy: 0.001 [°] B-axis angular travel: -20° / +115 [°] B-axis indexing accuracy: 0.001 [°] Pin Attachment: HSK40 Maximum speed Spindle: 30000 [rpm] Number of tool magazine stations: 40 Turning part by robot (6th side machining): Yes RS232 Port: Yes Installed power: 17 [kVA] Supply voltage: 400 [V] Operating hours: 9911 [h] Dimensions: 1500 x 2600 x 2300 [mm] Weight: 3400 [Kg] EQUIPMENT INCLUDED: x1 RENISHAW p ...

SEGATRICE AUTOMATICA a Doppia Colonna SHARK 350 NC HS 5.0 + Evacuatore Motorizzato a Paletta Segatrice a nastro automatica, a doppio montante, per eseguire tagli a 0° su acciai da costruzione, inox e legati, pieni e profilati, con dimensioni comprese in 350x350 mm. Di serie completa di: Evacuatore di trucioli motorizzato dragante, applicabile a destra o a sinistra della macchina. Regolazione della pressione delle morse. Alimentatore con rulli verticali per il contenimento delle barre. Macchina a controllo numerico CNC MEP 50-Windows CE” Based, progettato da MEP per l’automazione delle macchine di propria produzione. Ciclo di taglio taglio pulito” - L’alimentatore arretra la barra per evitare delle rigature sulla superficie tagliata quando il nastro torna in alto. Sistema di controllo a bus di campo con doppio microprocessore con collegamento seriale. Interfaccia uten ...

High pressure compressor LMF 40 bar Type: Eco Pet VD 1350 - B Year of manufacturing: 2003 Capacity: 1.350 m³/h Maximan pressure: 42 bar Electric power: 243 kW Working hours: approx. 35.800 h with Siemens S7 PLC and Danfoss frequency drive incl. pressure air buffer tank, 900 ltr. incl. air dryer incl. chiller / cooling tower the machine is dismantled and on stock in Germany

Temperature-controlled processing tanks are vital in various industries, including food, pharmaceuticals, and chemical manufacturing, where precise temperature management is essential for product quality and safety. Here’s a detailed overview of temperature-controlled processing tanks:, What is a Temperature-Controlled Processing Tank?, A temperature-controlled processing tank is a vessel designed to maintain a specific temperature range during the processing of materials. These tanks are equipped with heat exchange systems, temperature sensors, and control mechanisms that ensure the contents remain at the desired temperature throughout the processing cycle., Key Features, - Heating and Cooling Systems:, - Heaters: Can be electric or steam-based to raise the temperature of the contents., - Chillers: Usually water or glycol-based cooling systems to lower the temperature., - Insulation:  ...

Equipment for washing industrial tanks under high pressure. KONGSBERG OFFSHORE, LARGE UMBILICAL REEL 37 LINE, serial number 01.

High-precision lathe DMG Mori Wasino G 100/480 Year of Make: 2017 Control: Fanuc COMPACT line Temperature response (cold start): ø 2.0 μm Roundness: 0.5 μm Technical data: Spindle speed: Drive power: Turning diameter: 285mm Turning length: 280mm Bar Passage: 38mm Travels: X-axis: 480mm Z-axis: 285mm Accessories - 3 pcs of powered tools - Package rigid tool holders - Fire extinguishing system - machine only ran under oil - Chip conveyors

Lift system, Megamat, 170kg / shelf, approx. 6m high, – used - : Ex-site price: 14.500.- € (net), plus dismantling etc. Manufacturer: Megamat Type: Megalift 14448/25/6010 Year of Make: 2000 Max. load capacity per shelf: 170kg Max. total load capacity 18,000kg Dimensions per shelf: approx. 2.45m x approx. 0.80m Number of shelves: approx. 40 pieces Device dimensions: Height: approx. 6.01cm Width: 2.76m Depth: approx. 2.70m 3/N/PE 230/400V 10A, Fuse 16A Condition: good Available: immediately Location: BG-8800 Sliven

Offer 25032 Technical data: - Drilling capacity in steel ST 60 50 mm - Drilling capacity in steel ST 60 65 mm - Tapping device up to M 60 - Drilling spindle holder MK 5 - Drilling spindle stroke 240 mm - Projection 400 mm - Table with 2 T-slots 720 x 560 mm - max distance table – drilling spindle approx. 850 mm - 4 feeds 0.1 - 0.2 - 0.3 - 0.4 mm/rev - AZ continuously variable transmission with manual transmission - Drilling spindle speeds infinitely adjustable 40 - 1600 rpm - Drive 400 V / 5.5 kW - Space requirement approx. W 850 x H 2480 x D 1350 mm - Weight approx. 1450 kg

CHIRON FZ 08K S Magnum HSP High-Speed CNC Machining Center TECHNICAL FEATURES: Year: 2007 NC Type: FANUC 18i-MB5 Number of axes: 7 X-axis travel: 450 [mm] Y-axis travel: 270 [mm] Z-axis travel: 310 [mm] X, Y and Z fast travel speed: 75000 [mm/min] Maximum diameter in bar turning spindle: 32 [mm] A-axis angular travel: 360 [°] A-axis indexing accuracy: 0.001 [°] B-axis angular travel: -20° / +115 [°] B-axis indexing accuracy: 0.001 [°] Pin Attachment: HSK40 Maximum speed Spindle: 30000 [rpm] Number of tool magazine stations: 40 Installed power: 17 [kVA] Supply voltage: 400 [V] Dimensions: 1500 x 2600 x 2300 [mm] Weight: 3400 [Kg] EQUIPMENT INCLUDED: x1 RENISHAW probe type TS27R x1 Spindle Cooling Unit x1 watering tray x1 unit for 6th side machining x1SCHUNK gripping system x84 HSK40 Type Tool Holder x14 Collet Type F35 x1 Electrical Cabinet Air C ...

Centrifugal pump, high pressure pump, water pump, multistage vertical centrifugal pump, booster pump, booster pump -Manufacturer: KSB, inline pump MOVI -V 25/104-3 -Drive: 0.55 kW -Speed: 2840 rpm -max. delivery rate: 0.5-2.4 m³/h -max. head: 39-24 m -Dimensions: 185/185/H555 mm -Weight: 22 kg

Centrifugal pump, high pressure pump, water pump, multistage vertical centrifugal pump, booster pump, booster pump -Manufacturer: KSB, Movichrom high pressure pump - G 3/5 PN25 G2 -Drive: 0.75 kW -Speed: 2810 rpm -max. delivery rate: 3 m³/h -max. head: 33 m -Dimensions: 220/250/H580 mm -Weight: 34 kg

High-current terminal, terminal, series terminal, through terminal, switch-disconnector -Manufacturer: Phoenix Contact -91 pieces: high-current terminals, type PTPOWER 95 -99 pieces: high-current terminals, type PTPOWER 95-PE -290 pieces: high-current terminals type PTPOWER 95 (P) -130 pieces: type EB 2-25/PT -Manufacturer: DILOS -3 pieces: switch disconnector type D/061324-201 -Component: are sold together -Price: complete -Weight including packaging: 130 kg

Conveyor belt / conveyor belt / high conveyor / downward conveyor - Length: approx. 3,050 mm - Belt width: approx. 400 mm - With geared motor - Plastic link belt with curved carriers 100 mm high ---------------------------------------------------------------------- Conveyor belt / transportation belt / high conveyor / down conveyor - Length: approx. 3-050 mm - Belt width: approx. 400 mm - With gear motor - Platic link conveyor belt with bended catch 100 high

Centrifugal pump, high pressure pump, water pump, multi-stage vertical centrifugal pump, booster pump, booster pump -Manufacturer: KSB, high pressure pump Movichrom - G 9/2 PN16 G2 -Drive: 1.1 kW -Speed: 2825 rpm -Max. Delivery rate: 9 m³/h -Max. Delivery head: 22 m -Price: per piece -Number: 1 pieces -Dimensions: 250/210/H555 mm -Weight: 37 kg/piece

Stuffing box for screw conveyor, screw conveyor, screw conveyor, conveyor technology, pipe screw conveyor, drying screw, cooling screw, cooling pipe screw, heating screw, heating pipe screw, screw heat exchanger -Stuffing box: for Ø 40 mm shaft -for gland tape -conical socket suitable for high pressure -Number: 1x glands available -Price: per piece -Dimensions: 160/160/H103 mm -Weight: 3 kg

High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 -Engine power: 1.35/1.8 kW -Speed: 41-1700 rpm -Columns: Ø 200 mm -Spindle stroke: 125 mm -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm -Weight: 1500kg

High-voltage system, high-current system, high-voltage system, transformer -Manufacturer: Himmel, high-voltage system, high-current system -Type designations: Sky HG 64-25 KTS-01 9942 -High frequency: 0.7 MHz -Rated power: 25 kW -Individual components/technical data: see photos, nameplate -Dimensions: 1605/880/H1840 mm -Weight: 830 kg

Centrifugal pump, high pressure pump, water pump, multistage vertical centrifugal pump, booster pump, pressure amplifier pump -Manufacturer: KSB, high pressure pump type Movichrom CN 9/2 PN25 CN1 -Drive: 1.1 kW -Speed: 2900 rpm -max. flow rate: 9 m³/h -max. discharge head: 22 m -Dimensions: 280/250/H540mm -Weight: 43 kg

Pallet trucks, special pallet trucks for high pallets, pallet trucks, pallet jacks -Load capacity: 2000 kg -Dimension when retracted: 195 mm -Extended length: 320 mm -Fork length: 1010 mm -Fork width (outer): 665 mm -Inner fork width: 345 mm -Weight: 105 kg

High-voltage motor, electric motor, three-phase asynchronous motor with squirrel-cage rotor -Power: 630 kW -Voltage: 10500 V -Speed: 1493 rpm -Shaft: Ø 65 x 140 mm -Design: B3 -Protection class: IP 54 -Documentation: everything available -Quantity: 1 piece available -Dimensions: 2440/1885/H1500 mm -Weight: 5000 kg

High-performance grinding spindle, internal grinding machine, internal grinding device, internal grinding spindle -Handover: in current condition as viewed -Condition: without grinding spindle -Grinding spindle for: Lathe -electric: operated -Motor: VEM 0.75 kW -Bracket: Ø 80 mm -Dimensions: see photos -Total dimensions: 600/370/H350 mm -Weight: 60 kg

High-pressure standpipe -Pressure: maximum 30 bar -Predos is a special high-pressure stainless steel standpipe with a burst pressure of 70 bar. -Pressures of up to 30 bar may be required when clearing blocked drains. -High-pressure gauge -with lid lifter type: Hercules -in the suitcase -Dimensions: 1200/360/H200 mm -Weight: 16 kg

A used cutting machine Polar 78XT Touch screen Side Tables Chrome-plated table Air table

bore capacity in steel (diameter): 32 mm arm length: 1230 mm table surface area: 1200 x 500 mm bore stroke: 180 mm feed - independent: 0,10 - 0,15 - 0,20 - 0,30 mm turning speeds: 60 - 1800 U/min taper MK: 4 total power requirement: 2,7 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 2,2 x 1,8 x 2,3 m Quick radial with: - Feed - Thread cutting device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 26119 Technical data: - Drilling performance in steel ST 60 30 mm - Drilling spindle holder MK 3 - Drilling spindle stroke 125 mm - Drilling spindle speeds infinitely variable 80 - 3200 rpm - Tapping option by reverse / counterclockwise rotation up to M 20 - Projection 260 mm - Max. distance table - drilling spindle 825 mm - Table with 2 T-slots 500 x 360 mm - Height adjustable via rack with hand crank - Drive 400 V / 0.8 / 1.5 kW - Space requirement approx. W 500 x H 1900 x D 950 mm - Weight approx. 230 kg - Cross table with handwheels

T65 Digital Ultra Turrax Currency: MYR PIC: - Ms. Fatimah (013 628 7197/ fatimah_asmadtopglove.com.my) - Ms, Farha ( 01111936236/ nurfarha_atopglove.com.my

A Polo slant bed filter with vacuum filter endless belt design and enlarged storage tank is available. Capacity: 5000l, max. operating temperature: 60°C, flow rate per minute emulsion/oils: 650l/200l, dirt chamber capacity: approx. 400l, vacuum chamber capacity: approx. 140l, connected load: 5kW. Filter unit dimensions X/Y/Z: approx. 2450mm/1650mm/1550mm, filter unit weight: approx. 1150kg, total weight: approx. 3000kg. Documentation available. An on-site inspection is possible.

Press capacity: 45 ton Ram stroke adjustable: 10 - 40 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 220 - 300 mm Free frontal opening L-R: 560 mm Table surface area : 550 x 450 mm Slide area: 550 x 360 mm Hole in table: 450 x 100 mm Number of strokes: 100 - 500 s.p.m. Required power: 7,5 kW Weight of machine approx.: 6,2 ton