127,554 used machines on RESALE, but how to find them? Machine Search
Folding sheet press Tränklein BP; good condition; cleaned and tested; Working width 820mm. Bundling press Tränklein BP; good condition; cleaned and checked; working width 820mm.
automatic baler Manufacturer: HSM Type: VK 8818 R-FU Year of construction 2021 Operating hours: approx. 81 Technical data: Press force: 1000 kN Specific pressing pressure: approx. 120 N/cm² Channel format: 1,100 x 750 mm (W x H) Binding: 5-fold horizontal Wire push-through: seen in the direction of pressing on the left side Filling opening: 1,800 x 990 mm Drive power: 2 x 45 kW Control: S7-300 Theoretical throughput: - At 20 kg/m³ bulk density: approx. 12.86 t/h - At 50 kg/m³ bulk density: approx. 32.15 t/h Practical throughput: approx. 50 % of the previously mentioned theoretical performance Cycle time: approx. 8.3 sec. Bale dimensions: approx. 750 x 1,100 x length (600-1,200) mm Bale weights: approx. 500 - 750 kg Machine weight: up to approx. 30,000 kg Optionally with: Press feed belt Manufacturer: ? from ...
Daniels 500ton Upstroking Press Platen 1050mm wide x 1100mm deep Capacity in Tons: 500 Working pressure Lbs: 2950 Daylight between tables: 24"/30" Daylight between platens: 18"/24" Stroke (main ram): 24" Main ram dia. : 22" Side ram dia. : 3 1/2" / 2" 4 columns Return Ram Steam heated platens New light guarding Fast / slow close Complete with pump unit and brand new control panel
used baler Manufacturer: PAAL Type: DOKON 500 with twine tying Year of construction: May 2014 Technical data: Binding: 5-fold horizontal Press weight up to: approx. 30 t Press force: 122 t Specific pressing force: 9.90 kg/cm² Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 1 x 45 kW Throughput: 250 m³/h Pressing services: at 100 kg/m³ bulk density: approx. 25 t/h at 150 kg/m³ bulk density: approx. 30 t/h at 200 kg/m³ bulk density: approx. 35 t/h Binding: 5-fold horizontal Transport dimensions: Length: 13,300 mm Width: 2,600 mm Height: 3,300 mm without yarn unwinding devices, without control cabinet, without binding twine, without feed belt, without a personal protection system, without conveyor belt hopper and without walking surface with vertical la ...
Bank of 4x Bradley & Turton 120ton Upstroke Presses 20” / 500mm sq electrically heated platens Daylight adjustable 18” 2200psi 12” Ram diam. 12” stroke Return rams Solid state relay Hydraulic valve for Press up / down Quantity available: 4 complete with 1x pump unit.
Continuous press Manufacturer: Wemhöner Model: VSF Year of construction: 1972 Panel dimensions: 3600 x 2200mm Heating medium: Oil Feeding Destacking Total length approx.: 12.000mm
Technical data for the grating: Manafacture: Gi-Ro Vreden Condition of the goods: new (unobstructed) Reason for return: Wrong order end customer The scope of delivery includes: 01x Press grate, new (unobstructed) Material color: hot-dip galvanized Ctow7lyof8 Total depth: 1,000 mm (support rod direction) Total width: 980 mm (crossbar direction) Support rod diameter: 35/1.7 mm S355JR TS anti-slip: no QS anti-slip: no Edging: T-profile 35 mm Mesh size: 90 x 50 mm Weight: approx. 9.35 kg | Pcs. Internal designation: R
gebr. Veneer press OTT JUNIOR JU2511 Year 1998 ges. Connected load: 16.1 kW (rated current: 24.5 A) Pressing area: 255 x 110 cm Electric heating plates aluminum gold anodized Opening width: 40 cm 4 hydraulic cylinders each with a diameter of 90 mm Total pressing force: 70 t Spec. Pressure: 2.8 daN/cm² Hydraulic pressure max.: 275 bar Power per heating plate: 7,800 W Circumferential safety step strip inside + outside (emergency stop) Automatic opening (time-controlled) Stroke limitation / opening width limitation (adjustable limit switch) The press can be disassembled. External dimensions: approx. 304 x 123 x 191 (WxDxH) Weight: 3.0 t Guter gebr. Condition. Paint touched up in places.
On sale is a complete line for the production of longitudinal and transverse plates. 1. Weinig Dimter high frequency press. 2. Grecon Ultra4 longitudinal line. 3. Line for width connection Obel. 4. Hobelrotoles. 5. Timesavers 1350 mm grinding machine with three units. 6. Planer Schenko (with lifting platform for parcels) + conveyor belt + charger. 7. SLH cold width press. 8. Thermal tunnel for individual packaging of plates. 9. Glue applicator Inles. 10. Glue applicator for slats. 11. Obles line for longitudinal connection of slats.
ERIKA RECORD dough dividing and warp knitting machine Automat Type 4 - used, refurbished in 2023 - Type 4, 30 pieces, working range 40 - 120 g removable plastic dough enclosing ring Piston with non-stick coating Swivel machine head for easy cleaning Dividing knife electrolyt-plated four active times and active time switch-off (parts/presses only) no oil in the working area of the machine Machine with heavy casting stand for vibration-free operation Long-lasting, low-wear drive complete with three plastic knitted plates
ERIKA RECORD dough dividing and warp knitting machine semi-automatic type 4 - exhibition machine, brand-new condition, year of manufacture: 2025 - Type 4, 30 pieces, working range 40 - 120 g removable plastic dough embracing ring dough piston with non-stick coating tiltable machine head for easy cleaning dividing knife electrolyt-plated no oil in the working area of the machine machine with heavy casting stand for vibration-free operation complete with three plastic moulding plates
Press brake manufactured in 2023. This GWEIKE GKS-BC0315 features a pressing force of 50 t and a maximum sheet length of 1,600 mm. It is capable of bending dimensions up to 1,500 x 1,500 x 170 mm, making it suitable for large-scale boxes and panels. If you are looking to get high-quality bending capabilities, consider the GWEIKE GKS-BC0315 machine we have for sale. Contact us for further details regarding this machine.
3 × Hughes HPS 2200 High Pressure Pumps 320 bar – 228 l/min, used For sale are three used Hughes HPS 2200 high-pressure pumps in 100% working condition. The pumps were only taken out of service because the associated diesel engines and controls were needed for another project. Technical data Manufacturer: Hughes Pumps Ltd. (England) Model: HPS 2200 Max. operating pressure: 320 bar Flow rate: 228 l/min Pump speed: 400 rpm Input speed: 1,800 rpm Gear ratio: 4.50 : 1 Transmission oil: EP90 Oil capacity: 18 litres Years of construction 2 × built in 2010 (yellow pumps) 1 × built in 2009 (blue pump) ✔ 100% functional condition The operating hours cannot be specified because the original diesel engines and controls were already dismantled before storage. The pumps are suitable for a wide range of industrial applications, including water pumping, mining, mari ...
Embossing press - embossing machine Hydraulic Pressing surface, 600 x 2700mm Heated pressing surface
This press from Collin at Plastima Used Machinery in machine storage. The machine is from 2001 and is in good condition. – Brand: Collin Pilot & Lab Solutions – Model: P200P – Construction year: 2001 – Plate Size: 200 x 200 Mm – Max. pressing force: 196 kN
Viewing by appointment. Auction-ID: A1-40285-50
Piferoen type 5H baler complete with conveyor. Baling press 6.30m x 2m x 1.6m approx. Conveyor 7.5m x 1.2m x 0.80m approx.. Chamber size (WxDxH) 108 x 59 x 105 cm approx. Suitable for baling textiles and other products. Bales can be completely covered for protection of material.
Ex pressure vessel with agitator, MDG 45, 100 hours, V4424140313 Walther, mint condition Special price We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. The current price of a similar product is € 5.020 excl. Mwst. If you have a VAT number, we will gladly issue you an invoice without VAT. Top Condition like a demonstration unit The part was removed from a new machine that is proven to have run only about 100 hours of operation. Top cleaned and ready for immediate use. Technical data: - Ex Stainless steel pressure vessel MDG45, 42.8 liters, 4 bar, Walther-Pilot. - Ex electric agitator with gear motor, SK0Z/2G-63S/4 2G TF RD, Nord - Ex pressure regulator, V3540000000, Walther-Pilot - Pneumatic controller, ITV2030 34F2N3, SMC - Incl. industrial plug and cable - optional with Defende ...
SPECIFICATIONS: Cold press Working table mm: 2500 x 1300 No. 4 pistons Vertical stroke: 450 mm
Code: 0136 Brand: ITALPRESSE Model: FORMATIC 20.9 Hydraulic fluid membrane press Two sided lamination of veneer to panels shaped or profiled on one face and flat on the other to produce cabinet door raised panels, drawer fronts, desk tops, table tops, kitchen tops, etc. 3-D lamination of plastic foils (PVC, PPE, ABS, Transfer foil ) to panels sheped or profiled on one face to produce: cabinet doors, drawer fronts, desk tops, table tops, kitchen tops, store fixture components, room doors, etc. Platen dimensions mm 2000 x 900 Daylight mm 325 Cylinder stroke mm 325 Heating electric boiler Kw 27 Thrust ton 300 ton N° 3 thrust cylinders Hydraulic unit power Kw 5,5 Pressure control manometer Automatic pressure reset Opening timer Overall dimensions mm 3300 x 1400 x 2400 h Weight kg 8100
Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T
2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.
used canning press / packaging press Manufacturer: WAGNER Type: WDSP 7000 Year of construction: 1993 specifications: Pressing force: 70 t Specific pressing pressure: 318 kg/cm² Drive power: 15 kW / 400 V Duct format: 550 x 400 mm Filling opening L x W: 1,150 x 550 mm Compaction chamber: 700 x 550 x 400 mm Total stroke: 2,100 mm Machine length: approx. 5,500 mm Machine width: approx. 1,920 mm Capacity: approx. 1.5 t/h (depending on material) Package size, WxHxL: 550 x 400 x 280 - 550 mm Package weight: approx. 20 - 40 kg (depending on the setting of the package length) Machine weight: approx. 3,500 kg
Key data: 400 t, 800 mm
Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...
Inv. Num. : 6992 Type: LKT 250 Producer: METALPRESS Created: 1963 Parameters: Ram stroke: 120 mm Plunger adjustment: 100 mm Machine weight: 2700 kg
Code: 0158 Brand: ITALPRESSE Model: LOCK FORM SYSTEM AIR - CE Standard Hydraulic air membrane press with loading and unloading - CE Standard 3-D coated on one face lamination of veneer to panels shaped or profiled on one face and flat on the other to produce cabinet door raised panels, drawer fronts, desk tops, table tops, kitchen tops, etc. 3-D lamination of plastic foils (PVC, PPE, ABS, Transfer foil ) to panels sheped or profiled on one face to produce: cabinet doors, drawer fronts, desk tops, table tops, kitchen tops, store fixture components, room doors, etc. Platen dimensions mm 2650 x 1250 Piece height mm 55 Pressure control manometer Automatic pressure reset Opening timer
Specifications Maximum pressure: 54 tons Power supply: 400V / 7.5 kW Press force: 5.62 kg/cm² Year of construction: 2005 Bale size: 1200x800x1200 mm Productivity: approx. 2 bales/hr Bale weight: approx. 500 kg Price: on request Machine is fully functional, after technical supervision. Price also includes paint renovation.
Press-fit device for ceramic pins in rotor shafts Principle: The ceramic pins are fed to a test station via a pneumatic hose by means of a vibrating conveying bowl, where the position of any single-sided bore is checked. This is done with an optical sensor. Wrongly positioned parts are conveyed through a pneumatic slide into a collection container. Pins that are correctly positioned are fed through another pneumatic hose to the separator of the press-fit tool. The actual press-fit process is also carried out pneumatically with a roller bearing guided punch. First, a manually adjustable pressure p1 is used to check that the pin is not pressed too easily into the shaft. With a pressure p2, which can also be adjusted manually, the pin is then pressed into the rotor shaft at full stop. A 5,000 N preloaded disc spring package prevents excessive force from being exerted on ...
Hyundai high-pressure cleaner 1500 Watt Auction-ID: A1-40893-318
Specifications Maximum pressure: 12 tons Power supply: 380V/ 5.5 kW Press force: 2.5 kg/cm² Year of construction: 1985-1993 Bale size: 800x600x(600-1000)mm Productivity: approx. 3 bales/hr Bale weight: approx. 100 - 200 kg Price: on request Machine is fully functional, after technical supervision.
Inv. číslo: 4465 Type: PL-140 LC Výrobce: OMC Vyrobeno: 2014 Parametry: Příkon: 75 kW
Hyundai high-pressure cleaner 1500 Watt Auction-ID: A1-40893-74
Viewing by appointment only Auction-ID: A1-40285-109
This 8-axis AMADA HFBO 100-30 press brake was manufactured in 1998. It features a maximum press force of 1000 kN and a bending length of 3100 mm, providing robust capabilities for various applications. The machine has undergone software upgrades and cylinder replacements in 2024. If you are looking to get high-quality bending capabilities, consider the AMADA HFBO 100-30 press brake we have for sale. Contact us for further details.
Keeldiepte: 405 mm slag: 21 mm 55 slagen per minuut Punching pressure: 45 ton Max punching dia: Ø 27 in 13 mm / Ø 39 in 9 mm Power needed: 2,2 kW Length: 1300 mm Depth: 800 mm Height: 2050 mm Weight: 1000 kg
TRUMPF TruBend 5085 CNC hydraulic press brake was built in 2008 in Austria by TRUMPF Maschinen Austria GmbH & Co. KG. The machine, designed for the precise bending of sheet metal, is ideal for industrial plants that place emphasis on high repeatability and accuracy of manufactured parts. The combination of high press force of 85 tonnes with an extremely stable design ensures the best bending results, even during the most intensive use. The TRUMPF TruBend 5085 features a range of solutions designed to enhance user comfort and safety. It is operated via a convenient foot switch control and an advanced CNC controller with an intuitive interface and access to many useful functions. The LAZERSAFE system ensures safety in the work area by monitoring the bending zone in real time. If an operator or an obstacle is detected, the system immediately stops slider movement, minimising the risk of ...
echnical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg
Stainless steel platform movable for bread roll presses / dough dividing machines suitable for all common bread roll presses Solid construction loadable with 1 t Easy locking Stainless steel for optimal cleaning Dimensions: 735 x 640 x 170 mm, WxDxH NEW More TOP bakery machines and equipment in stock!
maximum number of results exceeded
please refine your search
1.100 € 
