hell used for sale

Electronic Module, Rack HELLER, UNI-PRO 20.002 041 14 slots spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 485 x 215 x 265 mm

Electronic module, control card UNI-PRO, HELLER B 23.032 304 ( B23.032304 ) SBUS 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 262 x 186 x 15 mm

Control panel, machine control panel HELLER BEA 05 DC Article number: 20002514 spare part for machining centre HELLER BEA 05 DC used, tested ! Dimensions: 390 x 220 x 150 mm

Electronic module, control card UNI-PRO, HELLER D 23.020 036X ( D23.020036X ) CUS 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 262 x 186 x 15 mm

DC gear motor, geared motor with brake HEYNAU ANTRIEBSTECHNIK G2V49MS/X/S 51,2 rpm gear ratio: 58.574 motor: PARVEX 0.19 kW 3080 rpm 24 V DC shaft diameter: Ø 14 mm wavelength: 30 mm groove width: 5 mm flange diameter: 110 / 160 mm, bolt circle diameter: Ø 130 mm hole diameter: Ø 9.0 mm drive base: 66 x 95 mm hole spacing: 49 / 83 mm 4x threaded hole: M6 x 1.0, depth: 15 mm approx. 1.5 m connection cable with coupling spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 290 x 180 x 160 mm

Control cabinet, machine control UNI-PRO, HELLER NC 80 C Dimensions ( control cabinet ): 650 x 370 x 1040 mm with punched tape reader spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions ( dimensions ): 900 x 510 x 1900 mm

Chip conveyor HELLER Type BEA 05 Inlet: 1040 x 250 mm Free belt width: 200 mm Height inlet: 270 mm Discharge: 260 x 240 mm Height discharge: 1300 mm coolant tank: approx. 200 litres drive motor: BAUER type: DK64SZ3-1112/163L 0.3 kW 9,0 rpm 220 / 380 V 3AC, 50 Hz coolant pump1: BRINKMANN Type: TB402/200 Q: 250 l/min, H: 13 m 1,7 kW 2850 rpm 230 / 400 V 3AC 50 Hz coolant pump2: BRINKMANN Type: TB100/170 Q: 100 l/min, H: 2 m 0,24 kW 2750 rpm 230 - 240 V 3AC spare part for HELLER BEA 05 DC used, tested ! Dimensions (with pallet ): 3460 x 1220 x 1750 mm

Electronic module, control card UNI-PRO, HELLER B 23.032 298 ( B23.032298 ) SIO 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 262 x 186 x 15 mm

Hello here we offer you a used semi-automatic metal band saw / band saw from MEBA Type : 230 GA-H Year of manufacture : ca 2007 Good condition, The machine was in a training workshop. The sale of this machine is only made to tradesmen or entrepreneurs. A visit is possible. Technical data are copied from the manufacturer, so without guarantee of 100% accuracy Automatic band saw Metal band saw Meba 230 GA-H with mitre cut. Automatic band saw Meba 230GA-NC Technical data: Manufacturer: Meba -Type:230GA-H -BJ. Approx. 2006-2007 (estimated) -with control (automatic) -with coolant pump -mitre cut possible -weight approx. 400kg -2 speed levels -high current -cutting range 230mm (see photo)

Electronic module, Rack UNI-PRO, HELLER B 23.034 330 ( B23.034330 ) RBEA 20.002 038 28 slots spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 485 x 215 x 265 mm

Electronic Module, Output Module UNI-PRO, HELLER A 23.020 018 ( A23.020018 ) 24V DC-Output 32A Junction strip: B 23.032 257 ( B23.032257 ) 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 262 x 193 x 51 mm

Hello cause renewal of machine park, we are selling a DARREL brand digital milling table purchased in 2017. The sale is URGENT, because we do not have the space to keep it and therefore have to sell it quickly. Ideal CNC machine for cutting Plexiglas, aluminum composite, wood, PVC, flexible materials 3000x1500mm plate New ELTE 2.2kw spindle (changed 1 month ago) New pads (changed 10 days ago) New variator (changed 10 days ago) 1 month old) In perfect working order, fully serviced. Intuitive software included Clamping flange on the periphery of the plate to block the materials Suction turbine Nose + Chip extractor Dies and cutters provided Demo possible by appointment Price negotiable To pick up in Marseille

Electronic Module, Output Module UNI-PRO, HELLER A 23.029 016 ( A23.029016 ) 24V DC-Output 32A Connector strip: A 23.020 206 ( A23.020206 ) 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 262 x 193 x 51 mm

Hello; We are selling our beautiful dispenser that fills all types of liquids (compote - alcohol etc.) quickly and efficiently. This dispenser can be used to fill all types of liquids and containers. The setting is very simple to operate. The machine is made of stainless steel and is very durable. NEAR MINT CONDITION The Professional kit includes : -Compressor (lowered machine kit): Ideal for not carrying your kegs. Angled outlet with anti-drip system. -Pneumatic pedal (for fast, efficient work). -Adjustable stainless steel tray. - Brand WEISSER -

Electronic Module, Rack UNI-PRO, HELLER A 23.032 248 ( A23.032248 ) RW02 20.002 614 9 slots spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 485 x 215 x 265 mm

Hello everyone for sale are approx. 500 lfd. Meter Gemac shelving. 6 floors/field/depth 1,200 mm. We are also happy to do this in partial quantities. Shipping and assembly can be arranged!

Power converter, power converter, transistor controller SIEMENS SIMOREG D165 G200/25 MREQ ( D165G200/25MREQ ) 6RB 2025-4DG00 ( 6RB2025-4DG00 ( 6RB2025-4DG00 0 ) Input: 380 V 3AC 50 - 60 Hz Output: 4x 200 V DC 25 / 50 A Ersatzteil u.a. for machining centre HELLER BEA 05 DC used, checked! Dimensions ( without front cover ): 540 x 300 x 500 mm

Encoder, speed sensor HEIDENHAIN ROD 426 A 1800 ( ROD426A1800 ) 223 675 0B 1800 L/revolution < br />Shaft diameter: Ø 6 mm Shaft length: 10 mm Flange diameter: Ø 50 / 58 mm bolt circle diameter: Ø 42 mm 3x threaded bore: M4 x 0,3x 7, Depth: 8 mm approx. 1.0 m connection cable with 11-pin plug spare part for HELLER BEA 05 machining centre DC used, tested ! Dimensions ( without connection cable ): 64 x 60 x 72 mm

Heat shrink tubing HELLERMANN TYTON TREDUX MA47 - 75/22 Art.-No. 323-50750 Product colour: Black Hose / pipe length: 1x 970mm, 1x 1060 mm diameter before shrinking: 75 mm diameter after shrinking: 22 mm Shrink temperature: min. 120 °C New ! Dimensions ( packaging ): 1070 x 120 x 100 mm

Spiral cable protection conduit, approx. 30m HELLERMANN TYTON SBPA9 Art.-No. 161-42200 Cable diameter : Ø 9 - 10 mm Bundle diameter: max. Ø 100 mm Inner diameter: Ø 9 mm wall thickness: 1.0 mm Material: PA 6 ( Polyamide 6 ) Length: approx. 30 m New ! Dimensions ( packaging ): 380 x 300 x 140 mm

Corrugated pipe, plastic hose HELLERMANN TYTON HG-HI54 166-11507 Inner diameter: 47,47,2 mm outer diameter: 54.5 mm length: 25 m Material: polyamide 12 ( PA12 ) Color: black New ! Dimensions ( packaging ): 900 x 800 x 300 mm

Servo motor, permanent magnet motor SIEMENS 1HU 3078-0AC01 ( 1HU3078-0AC01 ) 1,8 kW 2000 rpm 183 V 3AC IP54 shaft diameter: Ø 24 mm shaft length: 50 mm groove width: 8 mm flange: Ø 130 / 142 x 142 mm bolt circle diameter: Ø 165 mm hole diameter: Ø 11.5 mm timing belt wheel: Ø 88 mm, width 51 mm, teeth: 28 spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 555 x 145 x 190 mm

Servo motor, permanent magnet motor SIEMENS 1HU 3058-0AC01-Z ( 1HU3058-0AC01-Z ) 1,33 kW 2000 rpm 171 V 3AC IP54 Shaft diameter: Ø 19 mm Wavelength: 40 mm Groove width: 6 mm Flange: Ø 95 / 106 x 106 mm bolt circle diameter: Ø 115 mm hole diameter: Ø 9.5 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 460 x 130 x 120 mm

DC motor with tachogenerator BAUMÜLLER fGNF 132 MV ( fGNF132MV ) 19,5 / 36.9 / 36.9 / 19.5 kW 1000 / 1840 / 3100 / 6000 rpm 240 / 400 / 400 / 400 V DC external excitation: 310 / 310 / 116 / 58 V DC Flange: Ø 230 / 300 x 260 mm bolt circle diameter: Ø 265 mm 4x Bore: Ø 12 mm Tachogenerator: GHT 612/42 20 V at 1000 rpm with external control box main motor for machining center HELLER BEA 05 DC used, tested ! Dimensions: 1040 x 350 x 260 mm

Servo motor, permanent magnet motor SIEMENS 1HU 3078-0AC01-Z ( 1HU3078-0AC01-Z ) 1,8 kW 2000 rpm 183 V 3AC IP54 shaft diameter: Ø 24 mm shaft length: 50 mm groove width: 8 mm Flange: Ø 130 / 140 x 140 mm bolt circle diameter: Ø 165 mm hole diameter: Ø 11.5 mm timing belt wheel: Ø 88 mm, width 51 mm, teeth: 28 spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 550 x 145 x 190 mm

Gear motor with brake, two speeds SEW SF 30 DT71D8/2BN ( SF30DT71D8/2BN ) 0,06 / 0,25 kW 33 / 133 rpm 380 V 3AC IP55 Shaft diameter: Ø 20 mm Shaft length: 40 mm Groove width: 6 mm Flange diameter: Ø 80 / 120 mm bolt circle diameter: Ø 100 mm hole diameter: Ø 6.5 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 415 x 265 x 180 mm

Gear motor with brake, two speeds SEW RF 73 DT90L 12/2BMG ( RF73DT90L12/2BMG ) 0,15 / 0.9 kW 3.5 / 25 rpm 400 V 3AC 50 Hz IP54 shaft diameter: Ø 40 mm shaft length: 60 mm groove width: 12 mm Flange diameter: Ø 180 / 250 mm bolt circle diameter: Ø 215 mm hole diameter: Ø 14.0 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 665 x 250 x 305 mm

hydraulic slewing actuator, rotary actuator SÜDHYDRAULIK LÜBECK, KORK-STEINBACH GmbH HDK75.87H Drawing No.: 7008.0001 Shaft diameter: Ø 40 mm Wavelength: 87 mm 2x Groove width: 12 mm Flange diameter: Ø 100 / 180 mm bolt circle diameter: Ø 155 mm 8x Tapped hole: M10 x 1.5, depth: 27 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 275 x 180 x 190 mm

Directional control valve, hydraulic valve HYDRAULIK - RING WEF42A06C1 Pmax: 315 bar nominal diameter: 6 mm 1x control solenoid Control voltage: 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 150 x 46 x 95 mm

Directional control valve, hydraulic valve HYDRAULIK - RING WEE43K06C1 Pmax: 315 bar nominal diameter: 6 mm 2x control solenoid control voltage: 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 205 x 46 x 95 mm

Directional control valve, hydraulic valve HYDRAULIK - RING WEE43FE06C1 Pmax: 315 bar nominal diameter: 6 mm 2x control solenoid control voltage: 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 215 x 46 x 95 mm

Flow control valve, hydraulic valve, intermediate plate valve HYDRAULIK - RING HDDP1.5-06 nominal setting flow rate: 1.5 l/min Pmax: 315 bar nominal diameter: 6 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 85 x 46 x 47 mm

Flow control valve, hydraulic valve, intermediate plate valve HYDRAULIK - RING HDDP2.5-06 nominal setting flow rate: 2.5 l/min Pmax: 315 bar nominal diameter: 6 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 85 x 46 x 47 mm

Pressure reducing valve, hydraulic valve, intermediate plate valve HYDRAULIK - RING HVMP064A06B1 Final pressure: 6 - 64 bar Pmax: 315 bar nominal diameter: 6 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 185 x 46 x 48 mm

Check valve, hydraulic valve, intermediate plate valve HYDRAULIK - RING HROPO6B1 Pmax: 315 bar nominal diameter: 6 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 70 x 46 x 28 mm

Throttle valve, hydraulic valve HYDRAULIK - RING DV12-1.1/0P Pmax: 350 bar nominal diameter: 1/2 ( inch ) spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 90 x 38 x 100 mm

Hello, I would like to sell used (very good condition) semi-automatic liquid product filling equipment - a dispenser. Suitable for packing liquids, oils, cosmetics. There is automatic packaging mode. The machine is made in Germany, certified in the EU. Currently located in Lithuania.

Hydraulic cylinder, double-acting PARKER CFP3LRLS23M Piston diameter: Ø 38,1 mm ( 1.5 inches ) Rod diameter: Ø 25 mm stroke: 90 mm ( 3.543 inches ) rod thread: M20 x 1.5 Length: 40 mm pmax: 100 bar spare part for machining center HELLER BEA 05 DC used, checked! Dimensions: 265 x 130 x 52 mm

Directional valve, hydraulic valve HYDRAULIK - RING WEE42A06C2 Pmax: 315 bar nominal diameter: 6 mm 2x control solenoid Control voltage: 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 205 x 46 x 95 mm

Check valve, hydraulic valve, intermediate plate valve HYDRAULIK - RING HRYA06C1 Pmax: 315 bar nominal diameter: 6 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 84 x 47 x 40 mm

Check valve, hydraulic valve, intermediate plate valve HYDRAULIK - RING HRYC06C1 Pmax: 315 bar nominal diameter: 6 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 84 x 47 x 40 mm

Directional valve, solenoid valve, hydraulic valve PARKER D1VW20DNJWL76 210 bar 2x 24 V DC spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 235 x 46 x 90 mm

Piston distributor, 2 pieces, mounted VOGEL, SKF R 353.551 ( R353.551 ) piston distributor 353 2x 3 outputs spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions ( one distributor ): 85 x 63 x 20 mm Dimensions ( whole unit ): 180 x 85 x 20 mm

Centrifugal fan, centrifugal fan, centrifugal fan BAUMÜLLER Type: ODF 71-2 ( ODF71-2 ) Fan wheel diameter: Ø 180 mm 3000 - 3600 rpm Motor : 0,,0,45 - 0.6 kW 200 - 265 / 345 - 460 V 3 AC 50 / 60 Hz IP44 Input: Ø 183 mm, flange: Ø 220 mm, bolt circle: Ø 195 mm, 4x M6 x 1.0 output: 100 x 110 mm, flange: 131 / 170 x 124 / 158 mm, hole spacing: 127 / 150 mm hole diameter: Ø 9.0 mm spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 360 x 265 x 325 mm

Compressed air reconditioning, maintenance unit, pressure regulator HELLER, NORGREN BEA 05 DC with filter regulator and fine filter Control range: 0.4 - 10 bar P: max. 10 bar Connections: 1/2 spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 400 x 310 x 130 mm

Central lubrication, lubrication pump VOGEL MFE5 MFE5 / B3 / S3 Q: 0,5 l/min pmax: 28 bar pressure switch: DS-W12 motor: Type 3 DM7 0.07 kW 2700 rpm 180 - 220 / 315 - 380 V 3AC 50 Hz tank capacity: 2.7 l spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 270 x 130 x 330 mm

Cabinet Cooling Unit, Cabinet Cooling Unit BKM SKO5E1VY-20100 Rated Power: 0,,32 / 0.4 kW effective cooling capacity: 0.85 / 0.72 kW operating voltage: 187 - 230 V 1AC operating current: 4.3 A operating pressure: max. 24 bar IP44 / IP54 spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 410 x 250 x 655 mm

Coolant valve COAX 5-VMK 25 NC 54 25C110/0BD 24P 501152 P: 0 - 40 bar Control voltage: 24 V DC / 48 V AC External connection thread: M36 x 2,0 spare part for machining center HELLER BEA 05 DC used, tested ! Dimensions: 300 x 95 x 120 mm

Position switches, safety position switches, with roller lever SIEMENS 3SE3 120-1G-Z ( 3SE3120-1G-Z ) one NO / one NC max. 500 V max. 10 A spare part for machining center HELLER BEA 05 DC used, tested ! dimensions ( single switch ): 160 x 40 x 60 mm

Hello from Moers, We offer the modular solution for high-resolution prints from our packaging hall. The device is dismantled and is offered with a conveyor belt (see pictures) The conveyor belt is aluminum-based with an electric motor! Both articles can be viewed in Moers!