hegla gmbh co used for sale

Control unit, control panel, control panel, control unit, keyboard, screen, control, air humidification, dehumidification and evaporative cooling -Module: M4 (large display) -for: Condair CP2 -Type: M4 -Weight: 0.3 kg

Control OKUMA ... OSP P300M Clamping table surface ... 400mm Axis X ... 762 mm Axis Y ... 460mm Axis Z ... 460mm Spindle speed... 1000-15000 rpm. controlled axes ... 5 cooling... 20bar SK40 Main engine power ... 22/18.5kW Magazine slots ... 48 The machine is in good condition, possible to test under power.

Compressor CompAir L 75 Operating hours approx. 3100 h was used as a reserve compressor Volume flow 10.25 m³/min Motor power 75 kW Very good ready-to-use condition, directly from production!

Condenser LUVE Contardo with two fans, approx. 50 KW

Condenser LUVE Contardo Type HCE 74, with three fans 630mm, approx. 80 KW

Copy head, copy head, copy device, copy lathe -Copy head for: lathe -without: hydraulic unit -Dimensions: 1100/170/H370 mm -Weight: 143 kg

Diesel combined heat and power plant, CHP, generator set, power generator used A. van Kaick Year: 1991 Generator DKBN49/200-4 200 kVA 400/231 V 289 A 50 Hz Mtu 8V183TA32 MERCEDES OM 442A 240 kW 1500 rpm Tank dimensions approx. 3600 x 1500 x 1500 mm Dimensions container: approx. Mm Changes and errors in the technical data, information and prices as well as prior sale reserved.

Diesel combined heat and power plant, CHP, generator set, power generator used DIETER KUNZLER GmbH Year: 1991 Generator 250DMED 250 kVA 400/231 V 3x 362 A 50 Hz Mtu 12 V 183 AA 31 MERCEDES OM 424 225 kW 1500 rpm Container dimensions: approx. 6000 x 2500 x 2500 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.

Output module, control card, output card, controller -Control -Component carrier type: C-SPS-14 -Dimensions: 375/200/H200 mm -Weight: 3.8 kg

voltage phase frequency. 400V /3 Ph/50 Hz volume rate of flow 3,54 m/min stage pressures 7,5

Compressed air tank, pressure vessel, pressure tank, compressed air vessel, pressure vessel, compressor tank -Content: 11.5 ltr -permissible operating pressure: 17 bar -Dimensions: 270/250/H480 mm -Weight: 8 kg

Capacity: 400 l Heating: gas , 36 kW Outside dimensions 94 x 130 x 122 cm (HxWxD) Inside dimensions 48x110x80 cm (HxWxD) Mouting Voltage: 230/400 V , 50 Hz Cover: insulated,with springs and hinges of stainless steel, opening 90° Drainage: piston – type drain cock Equipment: valves for cold and hot water

Brand: Ambaflex Type: Apollo Width of the band: 400mm Transport height at the bottom: 400 mm Transport height above: 2000 mm

Copy head, copying head, copying device, copying lathe -Copy head for: lathe -with: hydraulic unit -Transport dimensions: 1200/800/H650 mm -Weight: 216 kg

1 used residual concrete recycling plant BIBKO ConTec, year of construction 1992, without control, spare parts available, rep. needy, sale ex location Upper Franconia

Frequency converter, frequency converter, drive converter, controller, variable speed drive -Power: 2.2 kW -Input: 380-480 V 50/60 Hz -Output: 4 kVA 5.8 A -Number: 2x available -Price: per piece -Dimensions: 340/85/H230 mm -Weight: 4 kg

Absolute encoder -Hollow shaft: Ø 12 mm -Dimensions: 80/85/H60 mm -Weight: 0.5 kg

Motor control, controller -Manufacturer: Phoenix Contact, Mosca Motor Control -Type: EG 45 ME2213 -Number: 12x available -Price per piece -Dimensions: 75/45/H130 mm -Weight: 0.3 kg/pc.

2.4 kg batch like new, only 4 x run, airflow, drum speed adjustable, Artisan cropster connection

Pressure power: 10 bar Pressure power: 150 l/min. tank: 150 l cylinder: St. With tank from Boge 150 litersThe techn. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 8500 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company, then contact us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 8000 mm y-travel: 1500 mm z-travel: 2500 mm Control: Heidenhain Itnc 530 total power requirement: 96 kW weight of the machine ca.: 55 t dimensions of the machine ca.: m Brand: CORREA/ANAYAK Typ: HVM 80 Build in : 2014 travel X/Y/Z 8,000 x 1,500 x 2,500 mm, Spindel : max. 6000 Rpm Spindelpower 28 Kw as extra :high frequency spindle, type HFS IMT Mold, max. 26,000 rpm, max. 11 kW, table dim. (floorplates)8,000 x 2,500 x 300 mm, T-slots 22 H12, distance T- slots 250 mm, table load max. 15,000 kg/m², distance spindle - column max. 1,675 mm, feeds X/Y/Z max. 30,000 mm/min, Total power 96 Kw machine weight 55,000 kg, column 12,000 kg, platen 16,000 kg, 2x CNC screen control, make Heidenhain, type CNC I 530, autom. tool changer, chain type, max. 60 tools, tool holder SK50, tool weight max. 25 kg, tool L max. 400 mm, radio manual control panel, make Heidenhain, type HR-550, telediagn ...

Precious chocolates coating drum Stainless, 250l coating drum, variable speed, forward and reverse, on stainless frame, 1Ph

Frequency converter, frequency converter, drive converter, controller, variable speed drive -Input: 380 V 50 Hz -Output: 380 V 100 Hz -Power: 18 KVA -Dimensions: 1160/480/H540 mm -Weight: 290 kg

Control unit, control, for power generator, emergency power generator, generator, aggregate, power generator, emergency power generator, power generation aggregate -Type: Compact 166-S -Number: 2x controls available -Price per piece -Dimensions: 490/110/H110mm -Weight: 2kg

Converter module -Type: S 909 -Number: 2x module converters available -Price: per piece -Weight: 6.3 kg

Speed Control Unit, speed controller, controller, engine governor, motor controller, motor control controller -Manufacturer: Phoenix Contact, Motor control: Motor control controller -Type: ME2213 -Dimension: 130/45/H75 mm -Weight: 0.3 kg

InterBus-S, bus coupler, Interbus -Manufacturer: Phoenix Contact, bus coupler -Type: IIBS ST 24 BK LB-T Ord.No. 2753232 -Price: per piece -Number: 3 modules available -Dimensions: 120/80/H110 mm -Weight: 0.5 kg/pc.

Inductive conductivity transmitter, conductivity transmitter, conductivity measurement -Manufacturer: EH Endress + Hauser, conductivity transmitter -Type: conducta XR 2 -Measurement range: 0 to 200 mS -Voltage: 220V 50/60Hz -Dimension: 180/95/H95 mm -Weight: 0.8 kg

Inductive conductivity transmitter, conductivity transmitter, conductivity measurement -Manufacturer: EH Endress Hauser, conductivity transmitter -Type: conducta XR 2 -100434-0100 -Measuring range: 0 to 100% -Voltage: 220V 50/60Hz -Dimension: 180/95/H95 mm -Weight: 0.8 kg

Control unit, control, for power generator, emergency power generator, generator, aggregate, power generator, emergency power generator, power generation aggregate -Manufacturer: Strüver, Control Unit Type Compact 166-S -Number: 2x controls available -Price per piece -Dimensions: 485/160/H115mm -Weight: 3 kg

Interface converter, converter, module converter, FL Comserver, DC/DC converter -Manufacturer:Phoenix Contact, DC/DC converter -Type: 3112.3 -Number: 3x converters available -Price: per piece -Dimensions: 85/25/H80 mm -Weight: 0.1 kg/piece

Käser ASK 32 T with integrated cold dryer Screw compressor Age: 2008 Rated Output: 18.5 kW Max. working overpressure: 8 bar Motor speed: 2950 1/min Sigma Control Integrated refrigerant dryer

Plastic crates, reusable containers Transport box, storage container, picking box Color: Blue toothed with lid Dimensions: approx. L 600 x W 400 x H 353 mm approx. 1,000 pieces available

VG1E-VN MANUAL FAST COLOR CHANGE TYPE POWDER COATING SYSTEM It is designed for powder coating applications with frequently color change within the day. Suction is directly from powder coating box that maintains easily fast color change. Equipment is movable. The chassis under the powder box is vibrating with the help of the vibration motor mounted under it. Powder suction tube is specifically designed to fluidize powder coating particles and to send them to the powder gun by help of the injector located at the top of this pipe with maximum efficiency. TECHNICAL SPECIFICATIONS Input voltage : 220V 50Hz Air need : 350 lt/min Input pressure : 6 bar Vibration motor : 220V 25W Gross weight : 75 Kg VM G01 POWDER COATING GUN AND CONTROLLER VM manual powder coating gun is fully demountable. Ergonomic pistol handle design provides ergonomic use and not tire operator while coat ...

VM VG1-VN VOGA MANUAL FAST COLOR CHANGE TYPE POWDER COATING SYSTEM It is designed for powder coating applications with frequently color change within the day. Suction is directly from powder coating box that maintains easily fast color change. Equipment is movable. The chassis under the powder box is vibrating with the help of the vibration motor mounted under it. Powder suction tube is specifically designed to fluidize powder coating particles and to send them to the powder gun by help of the injector located at the top of this pipe with maximum efficiency. TECHNICAL SPECIFICATIONS Input voltage : 220V 50Hz Air need : 350 lt/min Input pressure : 6 bar Vibration motor : 220V 25W Gross weight : 70 Kg VM G01 POWDER COATING GUN AND CONTROLLER VM manual powder coating gun is fully demountable. Ergonomic pistol handle design provides ergonomic use and not tire operator whil ...

VFDK-3 WALL TYPE CARTRIDGE FILTERED POWDER COATING BOOTH Wall-type powder coating booths are an economical manual powder coating booth solution for companies producing and powder coating small parts. These powder coating booths save space in the workshop and are a practical method of powder coating the work pieces to be painted. The wall-type coating booths can be combined with conveyors in transfer-type powder coating plants or have a simple conveyor line according to the project. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists of p ...

PATRONENFILTER FÜR PULVERBESCHICHTUNGSKABINEN Die Filter bestehen aus 100% reinem Polyester. Nachstehend sind die verfügbaren Standardgrößen aufgeführt 320x600mm 320x650mm 320x1000mm 320x1200mm Andere Größen und Spezifikationen können ebenfalls angefertigt werden. Kontaktieren Sie uns für weitere Informationen und Preise. für Pulverkabinen für Staubabscheider für automatische Maschinen für Pulverbeschichtungsanlagen hoher Wirkungsgrad antistatische Option Option Bajonettanschluss POWDER COATING BOOTH CARTRIDGE FILTERS Filters made of 100% pure polyester. Available standard sizes; 320x600mm 320x650mm 320x1000mm 320x1200mm Available polyester filter media density; 160 g/m2 200 g/m2 260 g/m2 Demands of different sizes and specifications can also be manufactured.

1. VFK CARTRIDGE FILTERED POWDER COATING BOOTH (1-SIDED) Cartridge type powder coating booths are cost-effective solutions for companies that generally use single color powder coating or do not change the paint color much. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists of pulse valves and a compressed air tank, controlled automatically or operated using manual buttons on the control panel. POWDER RECYCLING As a result of the filter cleaning system, powder coating particles fall down and are manually collected in a bucket at the bot ...

1. CONTAINER TYPE LIQUID SPRAY BOOTH Spray booth type : Side draft, enclosed type Air speed : 0,50 m/sec (empty spray booth) EXTERNAL DIMENSIONS Length (mm) : 6.058 Width (mm) : 2.438 Height (mm) : 2.591 INTERNAL DIMENSIONS Length (mm) : 5.900 Width (mm) : 2.350 Height (mm) : 2.390 SPRAY BOOTH BODY Entry doors : 2-leaf hinged door 1x leaf G3 filter for air inlet 1x leaf service and emergency door with a panic bar Body material : Mild steel and rectangular iron tube metar structure Insulation : 50mm PIR polyurethane filled sandwich panels, B1 class flammability Window : 2 set of 600 x 600mm waterproof PVC window Container base : Aluminum sheet, non-slip Lighting system : 2 pcs, 2x36W enclosed type armatures, Ex-proof Zone 2 Lifting : Lifting eyes at the top corner areas, forklift fork openings at the base HEATING SYSTEM Source : Electricity He ...

Pulverbeschichtungsanlage für Autofelgen Kann 4 Stück 22"-Felgen in 1 Charge pulverbeschichten Komponenten der Anlage: 1,5x1x1,28m Pulverbeschichtungsofen, 18KW elektrisch VFK-2 einseitige manuelle Pulverbeschichtungskabine Förderstrecke und Ladewagen Manuelle Pulverbeschichtungsanlage Lieferung - 8 Wochen EXW Istanbul Fabrik Inklusive Montage und Schulung Powder coating line for car wheels Able to powder coat 4 pcs of 22" rims in 1 batch Line components: 1,5x1x1,28m powder coating oven, 18KW electrical VFK-2 single sided manual powder coating booth Conveyor track and load trolley Manual powder coating equipment Delivery - 8 weeks EXW Istanbul Factory Assembly and training included

PULVERBESCHICHTUNGSANLAGE, TRANSFER-TYP Aushärteofen - Gas, Diesel oder elektrische Quelle Pulverbeschichtungskabine - Zyklontyp oder mit Patronenfilter Pulverbeschichtungsanlage - manuelles oder automatisches System Hängefördersystem - Raupenfahrwerke und Rumpfform Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachiger Ansprechpartner in Deutschland Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. abcs://vogamachine.com info@vogamakina

TRANSFER TYPE POWDER COATING LINE Curing oven - gas, diesel or electrical source Powder coating booth - cyclone type or cartridge filtered Powder coating equipment - manual or automatic system Overhead conveyor system - tracks trolleys and frull structure Contact us for quotation We provide the best technical solutions and competitive prices German speaking contact in Germany VOGAMAKINA Ltd.

2. VFDK-3 WALL TYPE CARTRIDGE FILTERED POWDER COATING BOOTH Wall-type powder coating booths are an economical manual powder coating booth solution for companies producing and powder coating small parts. These powder coating booths save space in the workshop and are a practical method of powder coating the work pieces to be painted. The wall-type coating booths can be combined with conveyors in transfer-type powder coating plants or have a simple conveyor line according to the project. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists o ...

POWDER COATING LAB HAND GUN WAGNER & GEMA COMPATIBLE, WORKS PERFECTLY WITH THE ORIGINAL CONTROLLER DELIVERY: 100Kv LABO HAND GUN 5m CABLE + COMPATIBLE SOCKET

POWDER COATING HAND GUN Cost effective and long life cascade Made in Turkey

The mixer combines hot and cold mixing. After hot mixing, the material automatically enters the cold mixer for mechanical cooling. -hot tank 800 l. - cooling tank 2000 l. - hot stirring time from 6 to 10 min. - cooling time from 10 to 15 min. - engine power 110 kW The device is adapted to the production of WPC terrace boards. Components needed for the product, such as PVC and wood dust or MDF dust, can be combined.

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

Powder coating line for car wheels Able to powder coat 4 pcs of 22" rims in 1 batch Line components: 1,5x1x1,28m powder coating oven, 18KW electrical VFK-2 single sided manual powder coating booth Conveyor track and load trolley Manual powder coating equipment Delivery - 8 weeks EXW Istanbul Factory Assembly and training included

Key data: 75 , 10 , 691

Parameters: -Max. pressure 10 bar - capacity 691.2 m3/h - power 75 kW - Built-in dehumidifier - PREVENTIVE MAINTNANCE support in 2019.

Verdichter, Compressor, Copeland Scroll ZR 40 K3E-TFD-522 Displacement: 9.94m3/h 2900 Red/min. Power, Amp.7 Year: New Refrigerant 134a, and others