he used for sale

Granulatore - Lame da mm 500.

Fine sanding machine Working width: 1300 mm. Workpiece thickness: 3-140 mm N? of units: 2 Wide belt, CSD sanding pad, belt sizes 2620 x 1350 mm, 18,5 kW motor,0,5-12 m/s belt speed with freq. Controlls, belt cleaning Wide belt, CSD sanding pad, belt sizes 2620 x 1350 mm, 15 kW motor, 0,5-12 m/s belt speed with freq. Controlls, belt cleaning Brush cleaning unit scotch bride 250 mm diameter, 4 kW Brush cleaning unit 150 mm diameter, 1,5 kW Feedbelt speed 5 - 25 m/min, 1,5 kW motor, frequency control Working height 930 mm +/- 20 mm Carpet cleaning brush EA dedusting machine high-pressure blow-off system with rotating nozzles and ionization for statically charged dust

- incl. Chip conveyor - incl. Chip crusher - Under power with  - incl. spare rollers - Power on hours  23.000 H - Working hours ca 8.000 H

: neu : ca. 10 Wochen ab Auftrags : Türkei : 60600 € : 1145.34 € : 3100 mm : 10 mm : 10 mm : 8 mm : 8 mm : 6 mm : 260 mm : 260 mm : 200 mm : 1,5 / 6 m/min : 7.5 kW : 5350 mm : 1600 mm : 1550 mm : 7685 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more than 60 % o ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 13800 € : 264.96 € : 1550 mm : 4 mm : 140 mm : 3,5 m/min : 2.2 kW : 2700 mm : 750 mm : 1000 mm : 1420 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls Motorised Back Roll (Power Rear Roll) Digital Read-Out The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 111500 € : 2107.35 € : 3100 mm : 20 mm : 20 mm : 16 mm : 16 mm : 12 mm : 350 mm : 350 mm : 260 mm : 1,5-5 m/min : 22 kW : 6000 mm : 2200 mm : 1900 mm : 15000 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT: infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommend ...

Tetra Pak's CAP 30 Flex is an optimal closure solution for attaching the cap to your container. The CAP 30 Flex is set to 1000 Slim HeliCap 23.

CNC Machining Center Hedelius T7 – 2600 1 R Magnum Control: Heidenhain TNC 7 Year of manufacture: 2023 Internal machine no. 56 Travels: X-axis F/H 2,600 / 2,030 mm Y-axis 750 mm Z-axis F/H 695 / 800 mm Pendulum operation: 760 / 1,300 mm Total clamping area 3,080 x 750 mm Table load: approx. 2,500 kg Integrated rotary table Ø 750 mm Interference circle diameter 1,100 mm Workpiece weight approx. 500 kg Mount: SK 40 Tool magazine: 50-fold Spindle speed: 50 - 14,000 rpm Power: 29kW Facilities - KinematicsOpt (incl. calibration ball) - Handheld control unit HR 510 FS - Compressed air nozzle on the spindle head - Inclined bed belt filter system 900l - Internal cooling (IKZ) 25 bar - Infrared Receiver M&H - 3D Infrared Probe M&H 25.50 - Touchsetter - Exhaust air filter - Partition wall - Blow-off guns - Rinsing guns

Excellent condition - Fully operational - Loading / Transport possible! maximum workpiece thickness 45 mm minimum workpiece length 220 to 350 mm maximum edge material height 50 mm minimum edge material length for fixed dimensions 330 to 400 mm maximum edge material protrusion top and bottom 2.5 mm Edge material protrusion front approx 10 to 20 mm Edge material rear protrusion ca 10 to 30 mm . minimum workpiece width 90 mm minimum workpiece thickness 10 mm maximum length with extension arm 4269 mm Working length with boom 4269 mm Depth with roller plates 1425 mm Working table height 888 mm Working width with support pushed in 210 mm Working table width with support rail extended 680 mm With milling unit

This 4-axis HELLER MCi 25 was manufactured in 2003. It features a generous X, Y, and Z-axis travel of 800 mm each, along with a B-axis capable of 360° indexing. The machine is equipped with a tool magazine holding 80 slots and supports a total of 6 pallets. If you are looking to get high-quality machining capabilities, consider the HELLER MCi 25 horizontal machining centre we have for sale. Contact us for further details.

This 4-axis Starrag Heckert HEC 400 D was manufactured in 2012. It features a maximum spindle speed of 12,000 rpm and a tool magazine capacity of 80 tools, allowing for efficient machining operations. The machine includes two workpiece pallets with a size of 400 × 500 mm. If you are looking to get high-quality machining capabilities, consider the Starrag Heckert HEC 400 D horizontal machining centre we have for sale. Contact us for further details.

This 3-axis HEDELIUS C60 - 2000 vertical machining centre was manufactured in 2007. It features an impressive X-axis travel of 2000 mm, Y-axis travel of 620 mm, and Z-axis travel of 520 mm. The machine is equipped with a powerful 18.5 kW spindle and a tool magazine capacity of 30 tools. If you are looking to get high-quality machining capabilities, consider the HEDELIUS C60 - 2000 machine we have for sale. Contact us for further details.

This 5-axis HERMLE C 600 U was manufactured in 2000. It features an X-axis travel of 450 mm, Y-axis travel of 300 mm, and Z-axis travel of 400 mm, providing versatile machining capabilities. The machine is equipped with a HSK 63 tool holder and a Heidenhain iTNC 426 CNC control for precision operations. If you are looking to get high-quality machining capabilities, consider the HERMLE C 600 U universal machining centre we have for sale. Contact us for further details.

Two jigger dyeing machines from various manufacturers are available. 1) Thies type NT 2300, year of manufacture: 2015, max. working temperature: 98°C, max. fabric width: 2850mm, roller width: 3000mm, max. fabric length at thickness from 0.3mm: 3177mm. 2) MCS Maxi Jigger 98°, year of manufacture: 2021, batch liquor ratio: 1:2, roller diameter: 320mm, lower roller diameter: 139.7mm. Documentation available. An on-site inspection is possible. Individual sale is possible.

- A4 Automatic head 2.5 x 2.5 Degrees - Drum AC 24 positions - HeidenHain iTNC530 - HeidenHain HR-410 Wandwheel - Flatt guideways / High Ridgid machine  - Oil Chiller - Covered CE-Doors

Key data: 3000 mm, 4 mm

Hydraulic Swivel Bending Machine -Heavy welded construction -centrally driven bending beam -Hydraulic drives -Standard stroke 400 mm -Cybelec control screen retrofitted Machine is fully functional Year of construction 2000 With honeysuckle foot splints 100 mm and various accessories Viewing possible by appointment LxWxH approx. 5000 mm 2500 mm 2700 mm Weight approx. 8500 Kg

Tetra Pak THX21, Helix accumulator, 1500ml/1000ml (and smaller). In its function, the Helix accumulator THX21 collects the packaging between the filling machine and the downstream equipment. In doing so, it ensures that downtimes of the filling machine are reduced and that no damage occurs to packaging in waiting positions. On request, we can provide extensive services. In addition to consulting and planning, this also includes transport, assembly and assembly. We will be happy to provide you with a detailed, non-binding offer. All offers are subject to prior sale.

This 5-axis HERMLE C40U Dynamic universal machining centre was manufactured in 2011. It features a travel of 850 mm in the X-axis, 700 mm in the Y-axis, and 500 mm in the Z-axis. The machine has a maximum spindle speed of 10,000 rpm and a magazine capacity of 38 positions plus 43 additional. If you are looking to get high-quality machining capabilities, consider the HERMLE C40U Dynamic machine we have for sale. Contact us for further details.

A double-sided labeling machine Herma is available. Product length range: 25mm-110mm, product width range: 25mm-80mm, product height range: 50mm-320mm, labeling capacity: approx. 200products/min, machine dimensions X/Y/Z: approx. 3200mm/1350mm/2700mm. Documentation available. An on-site inspection is possible.

This 4-axis HELLER MCH 250 was manufactured in 2005. It features an XYZ travel of 800 x 800 x 800 mm and a pallet size of 630 x 630 mm. The machine is equipped with a 100-tool automatic tool changer and a 6-pallet pool for enhanced productivity. If you are looking to get high-quality machining capabilities, consider the HELLER MCH 250 horizontal machining centre we have for sale. Contact us for further details.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 12700 € : 243.84 € : 1270 mm : 5 mm : 140 mm : 3,5 m/min : 2.2 kW : 2470 mm : 750 mm : 1000 mm : 1350 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor manual Back Roll forward tiltable upper roll forward and reverse revs conical bending by tilt of backroll movable control panel users manual in ENGLISH or GERMAN OPTIONS: hardened Rolls€ 1.500,- Motorised Back Roll (Power Rear Roll)€ 1.200,- Digital Read-Out€ 1.200,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This 4-axis HELLER MC 16 was manufactured in 1999. It features a maximum spindle speed of 8000 rpm and an automatic tool changer with 40 positions. The machine is equipped with twin pallets and offers an XYZ travel of 630 x 630 x 630 mm. If you are looking to get high-quality machining capabilities, consider the HELLER MC 16 horizontal machining centre we have for sale. Contact us for further details.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 6700 € : 129.31 € : 1550 mm : 2 mm : 90 mm : 6 m/min : 1.5 kW : 2130 mm : 700 mm : 1200 mm : 545 kg 3 rolls asymmetric rolls - prebending 2 rolls driven by brakemotor lateral roll adjustable by handwheel longitudinal grooves in lower and lateral roll tiltable upper roll right / left rotation with double foot switch conical rolling device user manual in GERMAN or ENGLISH OPTIONS: powered back roll EUR 1.000,- digital readout EUR 1.100,- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This 4-axis HELLER MCP 250 was manufactured in 2000. It features a maximum spindle speed of 6000 rpm and an automatic tool changer with 52 positions. The machine is equipped with twin pallets and offers an XYZ travel of 800 x 800 x 710 mm. If you are looking to get high-quality machining capabilities, consider the HELLER MCP 250 horizontal machining centre we have for sale. Contact us for further details.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 159300 € : 3010.77 € : 320 to : 4050 mm : Y1 / Y2 / X und R Achse : 365 mm : 3600 mm : 410 mm : 630 mm : hydraulisch : 160 mm/s : 10 mm/s : 160 mm/s : 650 mm : 500 mm/s : 250 mm : 900 mm : 154 mm : 5300 mm : 1910 mm : 3230 mm : 20100 kg 1 SERVO MOTOR AND PUMP PER CYLINDER 4 axes (Y1, Y2,X andR) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import, backup and programm  ...

-Five colours max paper size 36x52 cms. -Perfecting 2/3 or straight 5/0 -Year 1995, 68 mil. real impressions -Alcolor dampening -Baldwin recirculation and refrigeration system -CPC 1.02 table control for ink motors and plates remote controls -Powder spray, Quick action plate clamps -Plate punch, No NP unit -Complete with all accessories, No damages -In nice conditions -Available immediately

This 4-axis HELLER MCH 250 was manufactured in 2007. It features a spindle speed of 6000 rpm and a BT50 tool holder. The machine is equipped with an automatic tool changer that holds 100 tools, enhancing productivity. If you are looking to get high-quality machining capabilities, consider the HELLER MCH 250 horizontal machining centre we have for sale. Contact us for further details.

: neu : ca. 14 - 16 Wochen ab Auf : Türkei : 23800 € : 456.96 € : Doppelsäulenführung : 5200x41x1,3 mm : 20-100 m/min : 460 mm : 460 mm : 650x460 mm : rund 380 mm, quadrat 380 : 590 mm : 0.55 kW : 4 kW : 0.12 kW : 3100 mm : 1000 mm : 1800 mm : 1520 kg blade brush control panel hydraulic vice hydromechanical blade tension inverter linear way material limit shaft height adjustment pressure adjustment coolant pump saw blade security switch gearbox 1,2 meter roller table user manual in GERMAN or ENGLISH OPTION: turn table for mitre cuts hydraulic top clamping from above The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : 2026 : 080186 : prompt, Zwischenverkauf v : Türkei : 81476 € : 1309.77 € : 1 : 69300 € : 135 to : 3050 mm : Y1 / Y2 / X und RAchse : 265 mm : 2600 mm : 450 mm : 530 mm : hydraulisch : 160 mm/s : 10 mm/s : 120 mm/s : 500 mm : 500 mm/s : 350 mm/s : 250 mm : 900 mm : 150 l : 15 kW : 4250 mm : 1700 mm : 2850 mm : 9580 kg Special campaign Special price and SKY 22 control free of charge Standard accessories: 4 axes (Y1, Y2,X and R) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5 in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and  ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 97400 € : 1840.86 € : 2050 mm : 30 mm : 30 mm : 25 mm : 25 mm : 20 mm : 350 mm : 350 mm : 260 mm : 1,5-5 m/min : 22 kW : 5000 mm : 2000 mm : 1900 mm : 11000 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT: infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened rolls are recommende ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 32480 € : 620.37 € : 1550 mm : 9 mm : 9 mm : 7 mm : 7 mm : 5 mm : 180 mm : 180 mm : 150 mm : 1,5 / 6 m/min : 5.5 kW : 3900 mm : 1150 mm : 1250 mm : 3250 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT (PRICES ON REQUEST): infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length hardened roll ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 11500 € : 220.8 € : 150 to : fix : 300 mm : 1570 mm : 280x200 mm : 5 mm/s : 10 mm/s : 2500 mm : 1000 mm : 2270 mm : 2100 kg steel welded frame stop at any position pressure manometer safety valve against overloading 2 V-blocks table height adjustable table up-down movement attachment control by operating lever according to CE regulations user manual in GERMAN and ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 1450 mm y-travel: 1100 mm z-travel: 1300 mm control: Siemens 840D PL Main spindle:: power capacity - main spindel: 50 kW max. Torque: 1.500 Nm turning speed range - main spindle: 20 - 6.000 min/-1 spindle diameter: 110 mm tool taper: HSK A 100 Tool-Presetter:: Turmmagazin / Tool Tower : 180 pos. change-time chip to chip: 5,5 sec feed range: 1 - 65000 mm/min rapid traverse ( X / Y / Z ): 65 m/min pallet changer:: size of pallet: 1.000 x 800 mm max. palett load: 2000 kg max. workpiece height: 1.700 mm Number of pallettes: 2 pos. dimension of workpiece: 1400 x 1400 mm total power requirement: - kW weight of the machine ca.: 25 t dimensions of the machine ca.: 8100 x 5350 x 4150 m - Siemens 840D Powerline CNC control - 2-position pallet changer - 180-position tool changer (HSK A 100) - Milling head with 180° B-axis (0.001°) - C-axis table (0.001°) - 80 bar coolant system with  ...

turning diameter over bed: 455 mm turning diameter over slide rest: 285 mm turning length: 1.000 mm center height over bed: 225 mm centre distance: 1.000 mm digital readout: 2-Achsen ANILAM bed width: 330 mm spindle taper: KK 6 DIN 55027 spindle bore: 45 mm turning speed range: 16 - 1.000 U/min power requirement: 3,0 / 4,2 kW taper in tailstock-quill: MK 4 dia. of quill: 62 mm quill stroke: 145 mm coolant: voltage: 400 V total power requirement: 4,5 kW weight of the machine ca.: 1,95 t dimensions of the machine ca.: 2,45 x 1,10 x 1,80 m - Serial-No.: 29-2561 - ANILAM 2-axis digital readout - 4-jaw tool holder - coolant equipment ATTENTION! Machine is sold without a chuck. Upon request and for an additional charge, the following 3-jaw spiral chucks can be included: - CENTER Ø 200 mm = 780.00 EUR - CENTER Ø 250 mm = 1,030.00 EUR The data for this ad was created with ModulMWS - the sof ...

- Prinect Classic Center - ALCOLOR dampening units - BALDWIN cooling - HEIDELBERG Easyplate - Paint roller washing device - Blanket washing facility - Grafix Alphatronic 200

Alcolor Vario continuous dampening CP 2000 - Digital machine control and diagnosis Preset feeder (autom. paper size setting) Autoplate (semi automatic plate loader) Cooling and recirculation (Technotrans beta.c 160 G) Coating unit with chambered doctor blade system IR-Dryer Ink-roller washing device - automatic Blanket washing device - automatic Extended delivery (X2) High-pile delivery Powder sprayer (Weko AP 232) Axis Control quality control Format (US Format 60,5 x 74 cm) Water cooled peripherals

Travel X/Y/Z: 2500mm/1000mm/770mm, table dimensions X/Y: 3200mm/1000mm, spindle speed: 8000rpm, tool positions: 40, tool holder: SK40, max. workpiece weight: 3000kg, feed rate: 30m/min, coolant pressure: 20bar. Machine dimensions X/Y/Z: approx. 6500mm/4500mm/3700mm, weight: approx. 21000kg, control: Heidenhain iTNC 530, control hours: 67334h, machine hours: 56616h, operating hours: 15872h. Including internal coolant supply, 3D measuring and infrared probe, chip conveyor and linear measuring system. Documentation available. An on-site inspection is possible.

Travel X/Y/Z: 2300mm/800mm/600mm, table dimensions X/Y: 1400mm/750mm, rotary table dimensions X/Y: 800mm/630mm, spindle speed: 12000rpm, tool positions: 30, tool holder: SK40, coolant pressure: 20bar, feed rate: 30m/min, rapid traverse: 40m/min. Machine dimensions X/Y/Z: approx. 6200mm/3700mm/3600mm, weight: approx. 16000kg, control: Heidenhain iTNC 530, control hours: 63330h, machine hours: 61892h, operating hours: 28295h. Including internal coolant supply, 3D measuring probe, chip conveyor and linear measuring system. Documentation available. An on-site inspection is possible.

: neu : ca. 4 Monate ab Auftragse : Türkei : 52500 € : 992.25 € : 60 to : 250 mm : 500x430 mm : 750x500 mm : 450 mm : 26 mm/s : 8,5 mm/s : 47 mm/s : 7.5 kW : 1820 mm : 960 mm : 2400 mm : 4000 kg 2-pillar guide table and ram with T-slots 2 hand operation stroke adjustment pressure adjustment front light barriers according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 4 Monate ab Auftragse : Türkei : 34400 € : 657.04 € : Doppelsäulenführung : 6000x41x1,3 mm : 20-100 m/min : 540 mm : 540 mm : 750x540 mm : rund 510 mm, quadrat 450 : rund 270 mm, quadrat 250 : 695 mm : 4 kW : 0.12 kW : 3000 mm : 1300 mm : 2150 mm : 2445 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock coolant equipment hydraulic uplift of sawing frame 3° inclined saw band user manual in GERMAN or ENGLISH (the vertical hydraulic clam ...

: neu : ca. 4 Monate ab Auftragse : Türkei : 46700 € : 891.97 € : Doppelsäulenführung : 8200x41x1,3 mm : 20-100 m/min : 810 mm : 750 mm : 910x750 mm : rund 600 mm, quadrat 600 : rund 360 mm, quadrat 360 : 725 mm : 4 kW : 0.12 kW : 4020 mm : 1600 mm : 2450 mm : 3970 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock coolant equipment hydraulic uplift of sawing frame user manual in GERMAN or ENGLISH OPTIONS: Hydraulic vertical clamping Micro cooli ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 73200 € : 1383.48 € : 2050 mm : 20 mm : 20 mm : 16 mm : 16 mm : 12 mm : 280 mm : 280 mm : 220 mm : 1,5 / 5 m/min : 16.5 kW : 4350 mm : 1700 mm : 1850 mm : 8550 kg 4 rolls fullhydraulic drive of upper roll and lower roll hydraulic infeed of lower and side roll digital read-out of lower and side rolls position hardened rolls conical bending device hydraulic load relieving of upper roll hydraulic drop-end bearing 2 working speeds central lubrication system protectionagainst overload moveable control pane according to CE rules OPTIONAL EQUIPMENT (PRICES ON REQUEST): infinitely adustable speed of rolls hydraulic side support hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: the max. sheet metal thickness isequivalent to 50 % of nominal capacity the cone length can be max. 30 % oremust be more than 60 % of roll length harden ...

: neu : ca. 4 Monate ab Auftragse : Türkei : 59700 € : 1128.33 € : 100 to : 300 mm : 680x420 mm : 1100x600 mm : 500 mm : 17.5 mm/s : 5,5 mm/s : 37 mm/s : 7.5 kW : 1850 mm : 1400 mm : 2650 mm : 5400 kg 2-pillar guide table and ram with T-slots 2 hand operation stroke adjustment pressure adjustment front light barriers according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 55600 € : 1050.84 € : 30 to : 200 mm : 500?800 mm : 600x1000 mm : 450 mm : 100 mm/s : 18 mm/s : 165 mm/s : 11 kW : 1950 mm : 1750 mm : 2650 mm : 4700 kg 4-pillar guide table and ram with T-slots manual stroke adjustment via cam switch manual and automatic operation front light barriers according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : Türkei : 37600 € : 718.16 € : 40 to : 1550 mm : X und Y Achse : 160 mm : 1260 mm : 320 mm : 380 mm : hydraulisch : 90 mm/s : 10 mm/s : 600 mm : 845 mm : 100 mm : 120 l : 5,5 kW : 2000 mm : 1600 mm : 2235 mm : 3450 kg NC control for immersion depth (Y) and back gauge (X) synchronization control by means of a torsion shaft sheet support arms light barriers intermediate pieces for the upper tool clamping die seat and die die seat with 4 V openings split upper tool, slightly cranked, divided pedal user manual in GERMAN or ENGLISH OPTIONAL EQUIPMENT: laser safety device Fiessler NC controlled R axis manual crowning table motorized crowning table The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Slowakei : 23700 € : 455.04 € : 40 to : 800 mm : X und Y Achse : 100 mm : 310 mm : hydraulisch : 38 l : 6 kW : 1750 mm : 950 mm : 1900 mm : 1640 kg : 420 mm : 1 : 10 mm/s : 12 mm/s : 40 mm/s : 0.02 +/- mm : 0.05 +/- mm 2 axes(Y andX) motorized backgauge with push button and manual fine adjustment with counter preselection of press depth Y and upper dead point intermediate piece with quick-release lever for upper tool clamping upper tool 1010/75/R0,8/105 1x835 mm + 1x835 mm divided die type2009/85° (V16/22/35/50 mm)1x835 mm + 1x835 mm divided 2 support arms according to CE rules oilfilling user manual in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 10 Wochen ab Auftrags : Türkei : 68700 € : 1298.43 € : 3100 mm : 13 mm : 8 mm : 50 mm : 13 1/min : 1.75 ° : 16 : 37 to : 1000 mm : 200 mm/s : 30 kW : 330 l : 2 Stk. : 840 mm : 600 mm : 3550 mm : 4280 mm : 2300 mm : 3600 mm : 2350 mm : 12500 kg Swing cut construction NC-preselection system D-touch 7 with touch screen for back gauge, cutting length, quantity, USB port Motorized back gauge 1000 mm on ball screws, folding upwards Clear control panel mounted on moveablearm Hydraulic hold down pistons are arrangedclose to the cutting edge Foot switch Central, manual blade gap adjustment Cutting line illumination Broad table with balls Piece counter Single and continous stoke Fold up finger guard 1.000 mm 1 squaring arm 1. 500 mm with scale,T-slot and tilting cam 2 supporting arms 1.000 mm with T-slot Simple replacement and grinding of theblades Variable adjustable cuttingleng ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 10200 € : 195.84 € : 150 to : fix : 300 mm : 1070 mm : 280x200 mm : 5 mm/s : 10 mm/s : 2050 mm : 1000 mm : 2270 mm : 1870 kg steel welded frame stop at any position pressure manometer safety valve against overloading 2 V-blocks table height adjustable table up-down movement attachment control by operating lever according to CE regulations user manual in GERMAN and ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 - 14 Wochen ab Auf : Türkei : 76820 € : 1451.9 € : 160 to : 4050 mm : Y1 / Y2 und X Achse : 200 mm : 3600 mm : 300 mm : 430 mm : hydraulisch : 160 mm/s : 10 mm/s : 140 mm/s : 620 mm : 250 mm/s : 858 mm : 104 mm : 15 kW : 4850 mm : 1900 mm : 2610 mm : 10500 kg 3 axes (Y1, Y2, and X axis) CNC control DT-10 - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB CNC controlled back gauge with linear guide and ball screw spindles CNC crowning table intermediate clamps for upper tool upper tool1010/A/75°/0,8, se ...

: neu : ca. 3-6 Wochen ab Auftrag : Türkei : 79900 € : 1510.11 € : 130 to : 1000 mm : 640 mm : 210 mm : 5 - 110 mm : 60 1/min : 630x400 mm : 90 mm : 330 mm : 11 kW : 2200 mm : 1372 mm : 3000 mm : 8200 kg 8-fold ram guide front protection by light guard manual ram adjustment mech. overload safety device automatic lubrication user manual in GERMAN and ENGLISH according to CE rules The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.