hardness used for sale

FOR SALE STANDARD SIZE MEASURMENT CRANKSHAFT OF MAK 6M 332AK TO WHOM AT MAY CONCERN; THE CRANKSHAFT HAD BEEN PUT ON V BLOCK AND FOLLOWING TESTS HAD BEEN CARRIED OUT. -Main and crankpin journals measurements had been carried out. -MPI test had been carried out and no. crack had been observed. Crankshaft were found typical. -Run-out measurement had been carried out found in good order. -Hardness test had been carried out to all crankpins and main bearing journal. All values had been found in permissible limits. -Crankshaft had been polished. CRANK SHAFT READY TO TRANSPORT AT IZMIR - TURKEY. WITH FULL SEVICE REPORT IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 .aliagamarine.com TURKEY ...

MAK M20 Spares for sale. 1.Reusable Cyl Heads Bare-Pressure Tested Free From Crack:8-10 2.Piston With Groove With in Limit:8-10 3.Con Rod-Free From Crack, Wear Within Limit:8-10 4.Fuel Pump-Good Condition:8-10 5.Reusable Liners Wear Below 0.20mm-Free From Crack, Welding or any Damages:8-10 6.L O Filter-Good Condition:2 7.Water Pump-Good Condition:1 8.Lube oil Pump-Good Condition:1 9.Turbo Charger K54-Good Condition:2 10.STD Condition 6M20 Crankshaft, Within Std Limits, no Crack, no Ovality , Hardness Within Limits:1 11.Cam Shaft 6M20-Good Condition:2 12.Woodward UG-8 - Good Condition:2 13.6M20 Engine Block-Good Condition:1 14.Cam Shaft Gear & Crankshaft Gear-Good Condition:2 15.FLY Wheel-Good Condition 6M20:1 16.After Cooler-Good Condition 6M20:1

Technical data: - working width 300 mm- glue roller diameter 140 mm- rubber hardness glue roller 70 shor speed 20 m/min.- Power 0.25 kW- voltage 400 V, 50 Hz- quick change device of the glue roller glue container and rolls made of stainless steel- CE Conformity dimensions: 800 x 600 x 500 mm- Weight: 60 kg

Hardness tester Manufacturer: Stiefelmayer with drawer Cabinet For more info please see photos

Technical data: - working width 300 mm- 2 x glue roller diameter 140 mm- rubber hardness glue roller 70 shor speed 20 m/min.- Power 2 x 0.25 kW- voltage 400 V, 50 Hz- quick change device of the glue roller glue container and rollers made of stainless steel- mechanical height adjustment of the upper glue application roller- mechanic digital display of the passage height- CE conformity

Hardening testers Manufacturer Zwick& Co. KG. Wolpert or others For testing or measuring the -RockwellC, MPA and JHT -Vickers hardness - and other Extensive accessories of weights, measuring plates, test diamond Special price

conventional haertepruefer for the Processes Rockwell C , B , A Analog measuring watch, manual operation, weight load system Standard compliant according to ISO6506 Performance 2 years At the price, no used hardness tester is worthwhile. Better to spend a little more, but with a guarantee. More info schuetz-licht.de/produkte/haertepruefer/haertepruefgeraete-rockwell/ha ertepruefgeraet/

Impact forming mill is used for dry and fine grinding of brittle materials with a hardness of up to 3 Mohs. the impact fine grading mill combines efficient impact grinding with efficient classification in one unit. The supplied materials are thrown into the liner by the milling tools at a speed of 60-130m/s and then shredded. the ground material is transported to the integrated cashier for processing by means of air and rotation of the grinding tool. the fineness can then be infinitely adjusted via the speed of the classifier. Particles that are too large are sorted out by classifiers and end up in the grinding zone for continuous comminution.

This is a granulate dishwasher from the manufacturer Wexiödisk, type WD-100GR from the year of construction 2016. Wexiödisk granulate pot dishwashers clean all stainless steel kitchen utensils with water added to plastic grains. Even burnt-in grease can be removed quickly and easily. The dishes do not need to be soaked or scrubbed; only loose food residues are scraped off to avoid unnecessary contamination of the rinsing water. Thanks to the unique, double-door push-through system, the WD100GR differs from all other pot washers on the market; The dirt and clean sides are completely separated from each other. The scope of delivery includes the inlet table, the cassette trolley and two cassettes. The inlet table is equipped with a water faucet and a hose holder, so that a hand shower can be installed quickly and easily for pre-rinsing. The dishwasher has undergone a major predictive insp ...

AGEING OVEN FOR ALUMINUM EXTRUSIONS The aging furnaces are used in the aluminium profile industry for the elimination of internal stresses of aluminum materials after extrusion and for hardening them. The ovens are custom designed as batch type with high speed ventilation and high efficiency in order to achieve needed hardness demand on the aluminum work pieces. Motion of the batches is done by a ground trolley or a ground conveyor system. The oven door could be an automatic guillotine type or manual hinged door. The whole process is PLC controlled, data logging option is an advantage during the operation. Electricity, liquid or gas fuel is used for heating the ovens. The ageing ovens are CE certificated and conforms to the European Norms.

Rental system Hosokawa Alpine AS 100 Aeroplex, not for sale. The Hosokawa Alpine Aeroplex AS spiral jet mill is a simple jet mill without dynamic classifier (different to our Hosokawa Alpine AFG) that allows the ultrafine micronization with a final fineness of around 10 to 150µm of different products. Mainly dry non abrasive materials up to 3 Mohs hardness can be pulverized although some models allow wear protection inserts within the grinding chamber (pending availability). The micronizer design without rotating parts (thus no bearings or grease) makes this mill especially suitable for pharmaceutical and food applications, although it´s used as well on the chemicals industry for instance. The comminution takes place inside the grinding chamber where the product is accelerated by the compress gas injected through the grinding nozzles causing the different particles to collide with ...

It is used in rubber and plastics mixing, warming mixing, sheeting mixing, etc. III Equipment specification XK400×1000 mixing mill 1. Main technical specification NO. Item Main technology data and feature A Main technology data 1 Roll diameter 400mm 2 Roll working length 1000mm 3 Roll linear speed Front:14.85m/min Rear:18.85m/min 4 Speed ratio of rolls 1:1.27 5 Max roll space 10mm 6 Compound feeding capacity 25kg-35kg 7 Motor power 37KW,n=980r/min，IE3 8 Dimensions 4400X1710X1850mm 9 Gross weight 8500kg B Feature of main machine 1 Roll size(mm) Ф400×1000 material alloy chilled hard cast iron, surface hardness HS70±2,Surface roughness: Ra0.2 Bearing type Adopt the aligning roller bearing, copper pressure ring, bearing taper 1:12 type Front roll is drilled roll and rear roll is drilled roll, can pass cooling water, e ...

-Plate rolling machine rubber urethane pinch roll 1-one-pass rolling with pre-bending -Plate sheet width max. 3000 mm -Plate thickness 2 mm depending on the material hardness -fully hydraulic operated with power unit self enclosed - 9 Kw electric power 400Vac/50 Top shaft size 110 mm -Lower roll size 380 mm urethane coated rubber -Hydraulic front opening for the unloading of closed shells. -Upper beam with adjustable pre-load to compensate the deflection of the top roll under load. -Console electric manual/automatic work sequence with digital readout. - EQUIPMENT INSTALLED WITH THE MACHINE -Vacuum cups lifter plate width 3000 mm -Automatic feed pusher plate sheet loader into the rolls- -Side support hydraulic operated with conveyor belts motorized cradle system, all parts rubber coated to protect the plate surface from scratches.

Rental Hosokawa Alpine UPZ 100 cryogenic system (LN2) by Alpine Rentals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX Suitable for cryogenic grinding with LN2 Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system with grinding tools of choice, small feeding hopper with a dosing channel, cooling screw to feed the LN2, LN2 container, filter and barrel to collect the fines. Includes an operating panel, switch cabinet and a vacuum cleaner. LN2 to be provided on-site This small size system with an universal mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. Suitable for the cryogenic grinding with liquid nit ...

table length: 2000 mm table width: 1000 mm table height: 850 mm Vertikal stroke: 40 mm weight of the machine ca.: 0,38 t dimensions: 2,0 x 1,0 x 0,9 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 11.5 - 13.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, parallel hole arrangement in a 25 mm grid on the sides. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 1200 mm table width: 800 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,35 t dimensions: 1,2 x 0,8 x 0,9 m Welding table SIGMUND Professional 750 + Plasma-nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top parallel hole arrangement in 50 mm grid on the sides. Incl. Foot basic equipment. Pictured accessories optional. Price indication plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 2400 mm table width: 1200 mm table height: 850 mm Vertikal stroke: 40 mm weight of the machine ca.: 0,55 t dimensions: 2,4 x 1,2 x 0,9 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 11.5 - 13.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, parallel hole arrangement in a 25 mm grid on the sides. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 3000 mm table width: 1500 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 1,5 t dimensions: 3,0 x 1,5 x 0,9 m Welding table SIEGMUND Professional Extreme 850 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 850 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top, parallel hole arrangement in 50 mm grid on the sides. Including basic equipment. Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Fully refurbished Hosokawa Alpine UPZ 100 used system by Alpine Originals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX, not suitable for inert operation (N2) Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system in large table fitted with pins (other grinding tools of choice could be offered for an additional price), small feeding hopper with a dosing screw, filter and barrel to collect the fines, blower and piping. Includes a relay control panel. This small size system with an universall mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mil ...

Copley tablet testing complete lab suite, supplied new in 2018 and in as new condition, complete with manufacturers manuals. Comprising of the following items of equipment. Dissolution 8000. 8 bath dissolution with printer DissoMate Degasser station DTG 4000. 4 bath dissintegration with printer FRV 2000. 2 wheel friability, variable speed TBF 1000. Tablet hardness tester with keyboard input and printer

HEF Durferrit Line - carburizing, quenching and tempering Nitrocarburizing in a salt bath and hardening of steel parts. Technology for saturation in a liquid medium of cyanide salts, consisting of: -SWQ 60/80/90 and - Salt bath for quenching and tempering -STC 35/80- Electrode furnace for carburizing, hardening and annealing -LSU 60/70- Salt bath for carburizing, hardening and annealing In this technology, the surface layer of the materials is saturated with small amounts of nitrogen and carbon in a temperature range from 480 ° C to 630 ° C. Bath size - 350 x 800 mm Basket size – Ø 300 mm x H 300 mm Saturation of the surface layer with carbon and nitrogen at a depth of 0.4 ÷ 0.6 mm Hardness HRC 64 ÷ 66 Maximum dimensions of details for cementation: Lmax = 550 mm, Ø 300 mm

table length: 2400 mm table width: 1200 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,99 t dimensions: 2,4 x 1,2 x 0,9 m Welding table SIEGMUND Professional Extreme 850 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 850 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top, parallel hole arrangement in 50 mm grid on the sides. Including basic equipment. Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 3000 mm table width: 1500 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 1,5 t dimensions: 3,0 x 1,5 x 0,9 m Welding table SIGMUND Professional 750 + Plasma-nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top parallel hole arrangement in 50 mm grid on the sides. Incl. Foot basic equipment. Pictured accessories optional. Price indication plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 2400 mm table width: 1200 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,99 t dimensions: 2,4 x 1,2 x 0,9 m Welding table SIGMUND Professional 750 + Plasma-nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top parallel hole arrangement in 50 mm grid on the sides. Incl. Foot basic equipment. Pictured accessories optional. Price indication plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 3000 mm table width: 1500 mm table height: 850 mm Vertikal stroke: 40 mm weight of the machine ca.: 0,8 t dimensions: 3,0 x 1,5 x 0,9 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 11.5 - 13.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, parallel hole arrangement in a 25 mm grid on the sides. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Fully refurbished Hosokawa Alpine CW 250 used machine by Alpine Originals. The pin mill Hosokawa Alpine Contraplex CW fitted with two driven contrarotating discs. It is used to grind soft materials, even with high fat or humidity content. It allows also the processing of certain flexible materials or those that can´t lose their properties during comminution in cryogenic mode using liquid nitrogen (LN2) freezing them. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 40 to 500 micrometer (µm) t ...

Fully refurbished Hosokawa Alpine UPZ 160 Pharma used system by Alpine Originals. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or p ...

Fully refurbished Hosokawa Alpine UPZ 315 used machine by Alpine Originals. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or pendulu ...

Fully refurbished Hosokawa Alpine AFG 140 used system by Alpine Originals. The Hosokawa Alpine AFG fluidized bed opposed classifier jet mill is perfect for the super fine grinding of different dry materials with a precise control over the particle´s top cut thanks to its integrated classifier wheel design, using the Hosokawa Alpine Turboplex classifier head ATP. This micronizer can be used to pulverize different coarse products to finer powders and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetic, etc. This grinder is able to process hard coarse products up to approx. 10 Mohs´ hardness without much wear and reaching an extremely high end-product fineness values between d97 4 to 100 microns top size (product dependent) at the lowest possible energy consumption. The comminution takes place in the bottom part of the  ...

table length: 1000 mm table width: 1000 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,3 t dimensions: 1,0 x 1,0 x 0,85 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 17-19.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, Side walls 150mm with parallel hole arrangement in a 25 mm grid. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. Other dimensions available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 3000 mm table width: 1500 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 1,1 t dimensions: 3,0 x 1,5 x 0,9 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 17-19.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, Side walls 150mm with parallel hole arrangement in a 25 mm grid. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. Other dimensions available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 1200 mm table width: 1200 mm table height: 850 mm Vertikal stroke: 40 mm weight of the machine ca.: 0,261 t dimensions: 1,2 x 1,2 x 0,85 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 11.5 - 13.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, parallel hole arrangement in a 25 mm grid on the sides. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 2000 mm table width: 1000 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,73 t dimensions: 2,0 x 1,0 x 0,9 m Welding table SIGMUND Professional 750 + Plasma-nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top parallel hole arrangement in 50 mm grid on the sides. Incl. Foot basic equipment. Pictured accessories optional. Price indication plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Fully refurbished Hosokawa Alpine AFG 140 used system by Alpine Originals. The Hosokawa Alpine AFG fluidized bed opposed classifier jet mill is perfect for the super fine grinding of different dry materials with a precise control over the particle´s top cut thanks to its integrated classifier wheel design, using the Hosokawa Alpine Turboplex classifier head ATP. This micronizer can be used to pulverize different coarse products to finer powders and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetic, etc. This grinder is able to process hard coarse products up to approx. 10 Mohs´ hardness without much wear and reaching an extremely high end-product fineness values between d97 4 to 100 microns top size (product dependent) at the lowest possible energy consumption. The comminution takes place in the bottom part of the  ...

Combi steamer Manufacturer: UNOX / Type: BAKERTOP Specifications: Model oven: XEBC-06EU-E1R Including base frame & extractor hood 400V / 50/60Hz / 9.9 kW / 16 A CEE plug 230V Schuko plug for the extractor hood Year of construction: 2019 RRP with base: approx. EUR 10,000 General: BAKERTOP MIND. Maps Bakery Oven / Combi Steamer by Unox Body made of stainless steel Low energy consumption due to high-quality insulation Door with double security pane Air gap prevents strong heating of the outer pane inner glass pane can be opened for cleaning Door with carbon fiber door lock and long-bend door hinges Door hinge left / door handle right (door hinge can be changed to the right – see accessories) with condensate tray under the door (direct drain connection) Safety thermostat height-adjustable screw feet Baking chamber: completel ...

Wide belt sander Boere TKKC+BKKC 1100 (bottom/top) Technical specifications: Machine type TKKC+BKKC 1100(bottom/top), in good condition, flow processing machine, with through-going feeder in machine. Motors number 6 works above the item, works beneath the item, Sanding width with infinitely adjustable speed 1100 mm Sanding rails 2 Rotating brush cleaner 2 Sanding rollers 2 Calibration milling heads 2 Sanding belt length mm 1900 Passage height max, mm 250 Hardness grade of roller in ° shore 60 Sensing of workpiece thickness mechanical Feedrate max m/min 25 Total connection kW Weight kg 6800 Machine type TKS / BKS, in good condition, flow processing machine, with through-going feeder in machine, number of motors 6, works above the item, works beneath the item, working width 1100 mm, with infinitely adjustable speed, motor size 4x15 Hp, with 2 rollers, 2 s ...

table length: 2000 mm table width: 1000 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,74 t dimensions: 2,0 x 1,0 x 0,9 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 17-19.0mm. The holes have a diameter of 16mm. Hole arrangement in 50 mm grid on the table top, Side walls 150mm with parallel hole arrangement in a 25 mm grid. Including basic equipment. Table height 850mm Accessories shown are optional. Price plus packaging and transport. Other dimensions available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

10′ x 3/4″ Cincinnati Mechanical Shear Material Width: 10′ Thickness: 3/4″ Serial # 6210 Model # 14611 Hardness: 300 Brinell 11 Hold-Downs Adjustable Entry Edge Guides

table length: 2400 mm table width: 1200 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,74 t dimensions: 2,4 x 1,2 x 0,9 m Welding table SIEGMUND Professional 750 + plasma nitrided is made of high quality steel S355J2+N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 17 - 19.0 mm. The holes have a diameter of 16mm. Hole arrangement in a 50 mm grid on the table top, Side panels 150mm with parallel hole arrangement in a 25mm grid. Incl. basic foot equipment. Table height 850mm Price plus packaging and transport. Other dimensions available. The accessories shown are not included in the scope of delivery. Optionally available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Test force: 250 kg checking height: 0-270 mm kind of tests:: Rockwell workpiece depth: 160 mm weight of the machine ca.: 88 kg dimensions of the machine ca.: 200 x 500 x 800 mm This hardness tester Frank 532 comes from a training company and has been maintained more than second hand. The general condition is according to the age, very good, all functions have been checked. - Table with manual adjustment - with precision dial indicator for direct reading The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

MAN 16V32/40 Crankshaft 2 Pieces available in our stock in Istanbul Turkey Crankshaft is in good condition STD size Tests are done for: Measurement Hardness Crack Bending For more information please contact with us: info@fin-marine

– after technical inspection – very good condition – German production – year of production 1996 – segmented shoe - the perfect solution for varnish / veneer TECHNICAL PARAMETERS: grinding width 1100 mm grinding height 1-150 mm Combo unit with task-controlled membrane grinding shoe aggregate motor power 11 kW blowing on the tape pneumatic oscillation two types of belt speeds of 4.5 and 18 m/s Aggregate with felt shaft engine power 0.75 kW shaft oscillation Unit with cleaning brush engine power 0.75 kW smoothly adjustable feed feed speed range 4-18 m/min feed motor power 1.5 kW electric height adjustment vacuum table fan motor power 3 kW connector diameters 4 x 120 mm, 1 x 150 mm transport dimensions (L/W/H) 200 x 245 x 210 cm weight 2500 kg 1. The Alpha Combi unit is a grinding unit with a contact shaft with a dia ...

Stx MAN 16V32/40 Crankshaft 4 Pieces available in our stock in Istanbul Turkey Crankshaft is in good condition standard sized Tests are done for: Measurement Hardness Crack Bending For more information please contact with us: info@fin-marine

MAK 8M25 Crankshaft 2 pieces available in stock Standart sized Measurement report is available Tested for cracks, hardness and oscillation For further information please contact us at info@fin-marine

Pharmatron 5Y tablet tester The hardness tester is ideal for measuring the breaking of tablets. Cycle time 25 tablets / 3mins, up to 33mm tablet diameter, 1Ph

Ripper 1 shaft With hydraulic pusher, brand: Laiotz, model: R-820/1000, cutting chamber: 800x800 mm, motor: 100 hp, rotor: 800x600 mm, blades: 40x40. Electrical panel. At Gester we know that rip mills are indispensable machines in the plastic market, designed to reduce the size of different types of parts, by crushing them. Machine oriented to the rough crumbling of a wide range of dimensions of raw material such as films, obtaining final granulometries less than 50mm. The feeding system will be adapted to the type of plastic to be crushed (hardness, size, shape) to obtain the maximum performance of the mill.

DESCRIPTION ITS twin-shaft shredders with low speed and high torque designed to guarantee high performance and maximum reliability in the shredding of tough or bulky materials. Their solid and sturdy construction surpasses any other shredder on the market. As previously said: Given the large size of the grinding chamber and the solid construction, they are particularly suitable for grinding bulky and tough products such as wooden pallets, cardboard cores, metal scraps of various kinds and sizes, stacks of paper / cardboard sheets and many other materials that are usually difficult to grind. APPLICATIONS Large rolled up carpet Cardboard cores Pile of cardboard sheets Metal scraps WORKING PRINCIPLE The material is fed through a loading hopper placed above the grinding chamber which contains two rotating hexagonal shafts, equipped with circular blades of prede-fined thickness w ...

chamber volume: 170 liter useable volume: -- liter friction: -- motor drive power: 800 kW Condition: used - Specification: internal mixer used as additional option: Rubicon batch-off plant - capacity approx.: 170 litres - rotor model: tangential design - drive controller: Allen Breadley - Control: Mitsubishi - Motor speed: 1,000 rpm - Gearbox: Panamax 9000 make Sumitomo - Rotor speed: 5.6 - 55.6 rpm - Chamber hardness: 45 -50 HRC - Motor: 800 kW - 1000 rpm - 380 V, 50 Hz - Moror make: Teco - Output: 27 tons/day - Cycle time approx.: 4 - 8 min - Height approx.: 7,500 mm - Weight approx.: 35,000 kg, incl. gearbox and motor Available as an option: - Batch-off system Make: Rubikon / Mattech - Cooling bars max.: 300 mm / 2x 80 mm The data for this ad was created with ModulMWS - the software solution  ...

We clear our grinding wheels warehouse, there are new wheels unused, undamaged. They are exclusively ceramic-bonded discs. Diameter from 200 mm - 500 mm Width from 10 mm - 40 mm Different bonds and hardness. Please contact us so that we can make you an offer. The discs are sold at reasonable prices.

table length: 4000 mm table width: 2000 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 2,5 t dimensions: 4,0 x 2,0 x 0,9 m Welding table SIGMUND Professional 750 + Plasma-nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 750 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top parallel hole arrangement in 50 mm grid on the sides. Incl. Foot basic equipment. Pictured accessories optional. Price indication plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.