ha used for sale

pressure: 160 t dayligth: 700 mm number of strokes adjustable: 30 - 180 min table-size: 1600 x 640 mm ram surface: 1440 x 950 mm distance between columns: 1600 mm hole in the table: 1300 x 350 mm ram adjustment: 100 mm daylight between the side columns: 640 x 700 mm stroke of ram - solid: 40 mm total power requirement: 30 kW weight of the machine ca.: 25 t dimensions of the machine ca.: ca. 3 x 2,3 x 4 m - With hydraulic overload - With shuttle table device Machinewill be partly recondition (with new paint, new cabinet) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Bread packaging machine Hartmann VS 310 Series: M86/ 211L Year of construction: 12/1993 Weight: 850kg

Table diameter: 0 mm Table height: 0 mm T-slot size: 0 mm Number of T-slots: 0   Technical data Rotary table Execution: Horizontal Clamping surface: Diameter: 500 mm Table load max.: 100 kg Number of T-channels: 6 T-channel width: 14H7 mm Dimensions: Length: 900 mm Width: 800 mm Height: 150 mm

cutting diameter: 250 mm capacity 90 degrees: flat: 280 x 220 mm capacity 90 degrees: square: 220 x 220 mm capacity 45 degrees: flat: 220 x 200 mm capacity 45 degrees: round: 230 mm capacity 45 degrees: square: 200 x 200 mm capacity 60 degrees: flat: 140 x 100 mm capacity 60 degrees: square: 100 x 100 mm capacity 60 degrees: round: 150 mm vice: 285 mm turning speed range:: 36/72 m/min dimensions of saw-band: 2950x27x0,9 mm total power requirement: 1,5 / 1,8 kW weight of the machine ca.: 460 kg dimensions of the machine ca.: 1150 x 1970 mm Furnishing: - semi-automatic band saw machine - with miter device 45 ° right - 60 ° left - EVO microprocessor control to control all functions - with both. Miter device, adjustable via large turntable - optionally manual or autom. Lowering the saw bow - BI-metal saw band - coolant device - Angle stop - Chip removal brush - Operating instructions in Ge ...

cutting diameter: 300 mm capacity 90 degrees: flat: 330 x 260 mm capacity 90 degrees: square: 260 x 260 mm capacity 45 degrees: flat: 270 x 200 mm capacity 45 degrees: round: 260 mm capacity 45 degrees: square: 250 x 250 mm capacity 60 degrees: flat: 170 x 170 mm capacity 60 degrees: square: 170 x 170 mm capacity 60 degrees: round: 180 mm turning speed range:: 40 / 80 m/min dimensions of saw-band: 3320 x 27 x 0,9 mm engine output: 1,5 / 1,8 kW weight: 670 kg Furnishing: - Miter band saw / semi-automatic, for cuts left up to 60 ° / right up to 45 ° - autom. Saw bow lowering, infinitely adjustable feed - Limit switch-off at the end of the cut - hydraulic vice clamping - manual function - built-in coolant device - large turntable with bearings - Required instructions - saw band - Chip removal brush - Operating instructions in German Special accessories included: - MEP LubeCut microdosing ...

sheet width: 2500 mm plate thickness: 30 mm pre-bending: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210015 Type of machine Hydr. 3-roll bending machine Make HAUSLER Type RMA 2500/30 Build in 1962 Type of control conventional Additional information max. widht 2500 mm Max. plate thickness 30 mm 3 rolls diameter upper oll 450 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

faceplate diameter: 3.000 mm swing diameter: 7.000 mm turning height: 3.000 mm Control: FANUC 18i-TB total power requirement: 60/75 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

used bread packaging machine Hartmann Automat VS 320 is for sale and immediately available in our warehouse in Bielefeld. The machine packs breads into bags and closes them with clip tape. The machine is also suitable for Arabic bread. Bread packaging machine Hartmann Automat VS 320 Year of construction : 09 / 2012 Voltage: 3x400V/N/PE 50Hz Power Input 4 kW Weight 1600 kg

Type: David Dehairing And Flaming Machine Slaughter performance approx. 40-50 pigs/hour Pigs up to approx. 270 kg Machine body in hot-dip galvanized or stainless steel design Built-in control cabinet Roller equipped with 36 special clubs Electrical power: 5.5kW Installation dimensions of the machine in cm: Width: 240 Lenght: 340 Height: 250 Delivery time: after advanced payment, the machine is generally refurbished and ready for delivery

Machine Details Warehouse number 1105-03409 Machine Type Machining Center - Vertical Brand MIKRON - HAAS Type VCE 1000 VF 3 Year of construction 1998 Control type CNC Control Haas Storage location FRANCE Country of origin USA Delivery time immediately Freight base EXW (Incoterms 2010) Technical details x-displacement 1016 mm y-way 508 mm z-way 635 mm Control Haas Table clamping surface 1219 X 457 mm Rapid speed 25 m/min Table load 1000 kg Speed range 7500 1/min Drive power - Milling spindle 15 kW Number of tools in the magazine 20 pieces Tool holder SK 40 Information IMMEDIATELY FREE IN GOOD CONDITION UNDER POWER

Generator Motor 32 KW at 15001 rpm

HANDTMANN VF-200 LINE ID.NO. 2132 Handtmann VF-200 + AL 216-21 + 220-16 hanger directly taken line from discontinuing production. VF-200 year mod 1998 remaining of the line 2000. Dimensions 580 x 130 cm H 180 cm

HANDTMANN PVLH 226-01 + 242-16 ID.NO. 2133 Handtmann PVLH 226-01 + 242-16 links + suspension year mod 2008 directly taken out of production. Dimensions 500 x 90 cm H 150 cm.

x-travel: 650 mm y-travel: 450 mm workpiece height: 585 mm Control: ADCOS CNC 400 total power requirement: 15 kW weight of the machine ca.: 5000 kg dimensions of the machine ca.: m H A U S E R (Switzerland) CNC Controlled Hi Precision Double Column Jig Grinder Model S 40 – CNC 311 / ADCOS 400 CNC Year 1981 / CNC modernized in 2008 # 0126 _____________________________________________________________________ Table size approx. 630 x 770 mm Table load capacity approx. 500 kg Table travel longitudinal max. (X) 650 mm Grinding head slide cross max. (Y) 450 mm Vertical adjustment of cross rail max. (W) 500 mm Grinding spindle stroke max. (Z) 140 mm Stroke number of grinding head (4cycles) 0,5-12 m/min. Vertical distance between Table/grinding spindle 0-585 mm Dista ...

Haver & Boecker SWA/MECII-20 Loading Device Haver & Boecker SWA/MECII-20 Loose loading device with scale for loading trucks or wagons with bulk goods Suitable for free-flowing non-dusty bulk materials Description Brand: Haver & Boecker Type: SWA/MECII-20 Year: 2003 Temperature limits: -10°C / 40°C Voltage: 230V Frequency: 50 Hz Pneumatic pressure: 5 bar; Max 40 kg Min 10 kg Dimensions: Section I L2.43 x W187 x H310 Section II L240 x W240 x H310 Haver Nettowage with frame Weighing and evaluating electronics MEC II-20 to control weighing and/or machine functions Advantages • high ease of use • easy programmability • PTB and OIML approval • 99 product type memories • User guidance via plain text display in 6 selectable languages Bt 15 operator terminal For automatic remote variety adjustment, including motor adjustment of the bag length/width  ...

Handtmann Vacuum Filler Type: VF200 Funnel Capacity: 90\240(liters) Total power: 7kW Filling Capacity: Max 5000kg/h Serving: 5 - 100,000 grams Unscrewing machine Frame loading for 200l trolleys Power Supply: Electric, 400V 50Hz 3N Stainless, acid-resistant steel External dimensions: 1500 mm x 1200 mm x 1900 mm Condition: Used / Device fully functional We have many other kealte plants and meat and fish processing machines : Bitzer,Copeland,Frascold,Lunite,Kueba,Guentner,Eco,Alfa-Laval,Goedhart ,Helpman

Handtmann Vacuum Filler Type: VF50 2600 kg/h Capacity: 50 liters Stuffing pressure: up to 55 bar Portioning range: 5-100,000 gr. Portioning speed: up to 420 portions / min with a tolerance of 10% Power: 4 kW 400V 50HZ 3N Net weight: 660 kg External dimensions: 580 x 950 x 1600 mm Condition: Used We have many others machines for meat industry and cooling - handtmann, seydelmann, viessmann, bitzer, copeland, . Check our offers.

Table length: 0 mm Table width: 0 mm Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series 16-M Technical data 1 column execution Table length: 600 mm Table width: 380 mm Longitudinal travel (X-axis): 500 mm Transversal travel (y axis): 300 mm Travel of the vertical slide: 450 mm Passage from grinding motor to table: 485 mm Max. grinding diameter: 230 mm with display-plate: 360 mm Stroke of spindle-nose: 340 mm Max. angle with taper grinding: up to: 16 ° Vertical travel of grinding spindle: stepless from: 1 mm up to: 110 mm Travel speeds: stepless from: 0.5 m/min up to: 12.0 m/min Planetary motion speeds: c axis stepless from: 5 rpm up to: 250 rpm Voltage 50 Hz 3x: 380 Volt Total power required: 10.2 HP Machine´s weight about: 4000 kg Overall dimensions machine: Length: 2700 mm Width: 1700 mm Height: 2850 mm Various accessories: fi ...

Table length: 0 mm Table width: 0 mm Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm CNC Brand: 0 CNC Model: 0 Control: FANUC O-M Operating hours: 55887 Technical data 2 columns execution Table length: 1320 mm Table width: 860 mm Longitudinal travel (X-axis): 1200 mm Transversal travel (y axis): 600 mm Travel of the vertical slide: 635 mm Passage from grinding motor to table: 750 mm Max. grinding diameter: 230 mm with display-plate: 360 mm Passage between the columns: 950 mm Max. angle with taper grinding: up to: 16 ° Planetary motion speeds: c axis stepless from: 5 rpm up to: 300 rpm Possible grinding-spindle speeds: stepless from: 9000 rpm up to: 80000 rpm With air-turbine max.: 160000 rpm Voltage 50 Hz 3x: 380 Volt Total power required: 8.5 kVA Machine´s weight about: 6300 kg Overall dimensions machine: Length: 3000 mm Width: 2500 mm Height: 2870 mm Various accessories: CN ...

Table length: 0 mm Table width: 0 mm Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series 16i-M Operating hours: 16841 Technical data Table: Table length: 1440 mm Table width: 860 mm Table load max.: 800 kg Carriage: Longitudinal travel (X-axis): 1300 mm Transversal travel (y axis): 800 mm Vertical travel (z axis): 635 mm Passage from grinding motor to table: 0 - 750 mm Max. grinding diameter: 230 mm with display-plate: 360 mm Passage between the columns: 970 mm Max. angle with taper grinding: up to: 16 ° Stroke speed Z-Axis: Alternating stroke mouvement, infinitely adjust. from Vmin.: 0.500 mm/min up to Vmax.: 14000 mm/min Stroke frequency Z: 5 Hz Stroke length Z, infinitely adjustable: 170 mm Radiale fine feed U-axis up to: 5.5 mm Planetary motion speeds: c axis stepless from: 5 rpm up to: 300 rpm Possible grinding-spindle speeds ...

Key data: 3100 mm, 6 mm

HACO TS 3006 hydraulic guillotine shears manufactured in Belgium in 2006, are used in manufacturing plants to cut steel sheets with a maximum length of 3100 mm and a thickness of 6 mm. The machine has vertically aligned knives with four cutting edges, which ensure high precision and quality machining of workpieces regardless of the thickness and type of sheet. The angle of the cutting knives and the gap between them are adjusted by means of two levers at the rear of the machine. During machining, the workpiece is pressed against the cam in order to take an accurate measurement on the gauge located between the front stop and the bottom knife. Two parallel hydraulic cylinders drive the cutting bar (the upper knife attached to the slider) to perform the movement in the up-down direction. The HACO guillotine shears are offered with equipment which includes a foot control, a modern HACO SP ...

HALOILA Film wrapper Model no.: Octopus T200 Manufacturing year: 2015 Maximum power: 20 kW Full load current: 45A Voltage: 3400VAC Frequency: 50Hz Max short circuit current: 6kA

Key data: 135 t, 3150 mm

HACO ERMS 36-135 CNC press brake was built in Belgium in 2006. The machine, with its robust construction and high press force of 135 tons, is ideal for even the most demanding machining of workpieces with a length of 3600 mm. To ensure a high level of safety and ease of use, the ERMS 135T CNC press is equipped with the intuitive HACO ATS 560 control and light curtains which prevent unwanted entry of the operator into the working area. The total weight of the press is approximately 88000 kg. Technical data of the HACO ERMS 36-135 press brake - maximum press force: 135 t - maximum sheet metal length: 3600 mm - controller: HACO ATS 560 - bending speed: 10 mm/s - approach speed: 100 mm/s - return speed: 80 mm/s - slider stroke: 200 mm - reaction time: 75 ms - distance between body walls: 3150 mm - safety distance: 300 mm - light curtains - foot control - motor power: 15 kW - ...

Hartford HV-80S X: 2060 - Y: 1000 - Z: 660 mm CNC X-axis: 2060 mm Y-axis: 1000 mm Z-axis: 660 mm Table dimensions: 2100 x 1050 mm Admission in spindle (ISO): ISO50 Power on the spindle: 25 kW Control : Meldas Toolchanger: yes Number of toolholders: 20 positions Number of rotations: 40 > 4000 rpm

Hartmann Slicer Bread Slicer Machine Type: SL50 Slicer Year of construction 1997 Weight: 1900kg 400V 50Hz with bread supply Feed belt Compressor closure analog control without knife

Hartmann Slicer Bread Slicer Machine Type: SL50 Slicer Year of construction 1997 Weight: 1900kg 400V 50Hz with bread supply Feed belt Compressor closure analog control without knife

Beutelverpackungsmasch., Hartmann, GBK 420

Beutelverpackungsmasch., Hartmann, GBK 420

machine measurements: 6.850 x 3.600 x 1.900 mm machine weight: 5.000 kg power capacity: 9 kW Condition: used - as good as new unit is still completely packed Specification: Medical surgical mask system complete Consisting of: - See sketches in the attachment Summary of the equipment: This machine is mainly used for automatic forming of plane mask: the whole roll of cloth is driven by roller after being unrolled, and the cloth is folded and wrapped automatically. The nose bridge strip is rolled up for traction and unrolled. After cutting with a fixed length, it is imported into the edge cloth. The two sides are welded to the seal by ultrasonic welding. The mask was transported to two mask ear belt welding stations by the assembly line, and the mask was finally formed by ultrasonic welding. After the mask is made, it is transported to the flat belt line through the assembly ...

machine measurements: 9.657 x 1.472 x 1.985 mm machine weight: -- kg power capacity: -- kW Condition: used - as good as new Specification: FFP 2 N95 mask system complete Consisting of: - see sketches in the plant - cycle time approx.: 35 - 50 pieces/min - not CE certified - Space requirement approx.: 9,657 x 1,472 x 1,985 mm - Completely assembled The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hartmann bread slicer and packaging line Hartmann Slicer SL 20 Year of construction 1998 Hartmann Automat GBK 220 Year of construction 1991 Bread slicer and packaging line Compact for whole breads and individual slices with closure Digital Screen Panel with air/compressor connection with new knives 230/400V 50Hz Total Kg: 1800kg 2 whole lines in stock! Directly from the bakery

Machine Details Warehouse number 1105-03446 Machine type machining center - Horizontal Haas brand Type HCE 400 P Year of construction 2000 Control type CNC Haas control system Storage location FRANCE Country of origin Japan Delivery time by arrangement Freight base EXW (Incoterms 2000) Price Technical details x-displacement 560 mm y-way 635 mm z-path 560 mm Haas control system Pallet size 400x400 mm Table load 400 kg Spindle motor 22 kW Spindle speed 8100 1/min Rapid speed 36 m/min Pallet changer type 2-fold rotation Table indexing 360000° ° Tool magazine: 30 x BT 40 Total power requirement 54 kVA Machine weight approx. 8 t Space requirement approx. 2.8 x 5.5 m Accessories Conveyor Information Still very precise horizontal center full B AXIS 30X BT 40 TOOL CHANGER CNC HAAS 2 PALLETS 400 X 400 MM

Stationary high-pressure pump unit Hammelmann HDP 122 on base frame. Similar but no Kamat, Uraca, Woma. Pump type: HDP 122 Operating pressure: 440 bar Flow rate: 92 l/min. Drive speed: 1500 rpm. Drive power: 75 kW with AC motors ACM 208S 75 kW electric motor, IP55, with pressure control valve, with safety valve, with oil cooling system. Dimensions LxWxH: approx. 1,800x900x1,450 mm Weight: approx. 1,230 kg Year of construction: 2015 Condition: in very good used condition.

; Gross weight [kg]: 4040; Inspection Date: 2024-03-18; Amount of previous owners: 1; Lift height[mm]: 1015; Maximum lift capacity [kg]: 450

Specifications: - Cutting length up to approx. 220 mm - Cutting thickness - Steel with 400 N/mm² strength 4 mm - Stainless steel with 600 N/mm² strength 3 mm - Cutting angle 90 ° - Stroke rate up to approx. 35 1/min. - Depth stops left + right - Table support surface 600 x 400 mm - Table height approx. 1000 mm - E – Foot switch - Drive 400 V / 2.2 kW - Space requirement approx. W 800 x H 1200 x D 650 mm - Weight approx. 500 kg

Mach. No.: AD 26953 - Motor: Scania - Rotor size: 1.400 x 1.500mm - Included: Conveyors, Overband Separator, Dumpbunker, Feeders, Pre-screen and Hydraulic openingssystem

Cream machine HagesanaManufacturer : HagesanaType : Cream-KingYear of construction 2007with coolingBaker's conditionDetails see picture

Machine Details Warehouse number 1105-03462 Machine Type Machining Center - Vertical HARTFORD brand Type VMC 1020 Year of construction 1999 Control type CNC Control FANUC OMD Storage location FRANCE Country of origin Taiwan Delivery time immediately Freight base EX WORK Technical details x-displacement 1020 mm y-way 510 mm z-path 510 mm Table clamping surface 1200 x 600 mm Speed range - milling 8000 rpm Control FANUC OMD Drive power - Milling spindle 11 kW Tool holder BT 40 Number of tool magazine slots 20 stations Feed range 1 - 10000 mm/min Rapid passages: 20 m/min Total power requirement 25 kW Machine weight approx. 5500 kg Space requirement approx. 2300x2200x2600 mm Accessories Full protection - fairing Complete machine documentation Information very nice MACHINE CONTROL FANUC O MD SPINDLE BT 40 8000 RPM All prices excl. VAT..

saw blade diameter: 400 / 425 x 40 mm cutting diameter: 40 - 180 mm cutting speed: 14/28 m/min capacity 90 degrees: flat: 260 x 80 mm capacity 45 degrees: round: 130 mm capacity 45 degrees: flat: 180 x 80 mm work height max.: 1050 mm voltage: 400 V total power requirement: 5,0 kW weight: 1170 kg range L-W-H: 1230 x 1205 x 1980 mm Furnishing: - semi-automatic underfloor saw - with miter adjustment, swiveling left / right - hydraulic, vertical & horizontal clamping device - large work table - stepless feed from the saw blade - saw blade - machine base The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Capacity (x): 0 Process Application: 0   Other Info: 0 Technical data Centre height: 102 mm Distance between centres: 370 mm Overall dimensions machine: Length: 400 mm Width: 200 mm Height: 300 mm

Capacity (x): 0 Process Application: 0   Other Info: 0 Technical data Centre height: 102 mm Distance between centres: 370 mm Overall dimensions machine: Length: 400 mm Width: 200 mm Height: 300 mm

Table length: 0 mm Table width: 0 mm Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series O-M Technical data 1 column execution Table: Table length: 600 mm Table width: 380 mm T-channel width: 10 mm Number of spline: 6 Distance of the T-slots: 50 mm Table load max.: 200 kg Carriage: Longitudinal travel (X-axis): 500 mm Transversal travel (y-axis): 300 mm Travel of the vertical slide: 450 mm Passage from grinding motor to table: 485 mm Max. grinding diameter: 230 mm with display-plate: 360 mm Stroke of spindle-nose: 340 mm Max. angle with taper grinding: up to: 16 ° Vertical travel of grinding spindle: stepless from: 1 mm up to: 110 mm Travel speeds: stepless from: 0.5 m/min up to: 12 m/min Planetary motion speeds: c axis stepless from: 5 rpm up to: 250 rpm Feeds: X axis: 0 - 12 m/min Y axis: 0 - 12 m/min W axis: 900 mm/min Voltage 50 ...