134,049 used machines on RESALE, but how to find them? Machine Search
Refurbished impact mill with 45 kW drive, inlet hood and hydraulic unit for opening the housing. The scope of delivery includes an extensive spare parts package (rotors, blow bars, wear pieces, impact mechanisms, etc.). Not run since the overhaul in 2025, therefore in very good condition.
Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.
Intermittent Carton Packaging Machine ZHJ-150 Exhibition Machine/ Exhibition Machine Multifunctional Cartoning Machine ZHJ-150 ZHJ-150 automatic cartoning machine is suitable for packaging aluminum PVC blisters, round bottles and special bottles, Shaped bottles and similar products. Package inserts can be folded automatically, cartons can be erected, products can be fed and the cartons can be resealed (offset plug-in closure). Embossing can be made on the cartons. This machine has PLC control, with each station monitored by photoelectric sensors. If there is a problem detected during operation, the machine will automatically stop and display the fault. This machine can run as a single machine and can also be connected to a blister packaging machine and other pre-machines. The machine can be viewed at any time in 73084 Salach/Germany and tried out with your products. Dependin ...
Pile feeder - separating head 2 buckles 1 knife Noise hood Batch counter LCD touch-screen control Belt delivery Sheet size : 490x650 mm - min. 120x172 mm (only Parallel fold) - min. 105x172 mm (with special equipment) - min. 174x174 mm (with cross fold) Fold length: min. 58 mm Paper weight : 40-250g/sqm Pile height : 590 mm Speed : 180 m/min
Table dimensions X/Y: 1370mm/660mm, travel X/Y/Z: 1250mm/660mm/635mm, speed: 8000rpm, spindle mount: BT40, tool positions: 32, spindle-table distance: 790mm, control: Siemens 810 T. Documentation available. On-site inspection is possible.
Travel X/Y/Z: 1270mm/660mm/610mm, speed: 10000rpm, max. table load: 3000kg, spindle mount: CAT40, tool positions: 40, machine dimensions X/Y/Z: approx. 3300mm/2800mm/3000mm, weight: approx. 9000kg, control: Ultimax. Documentation available. On-site inspection is possible.
Travel X/Y/Z: 1016mm/508mm/635mm, speed: 10000rpm, table dimensions X/Y: 1219mm/457mm, max. table load: 1550kg, tool positions: 20, rapid traverse X/Y/Z: 25m/min/25m/min/25m/min. Machine dimensions X/Y/Z: approx. 4000mm/2800mm/2600mm, weight: approx. 5400kg. Documentation available. On-site inspection is possible.
A Huron CNC bed milling machine is available. Travel X/Y/Z: 2400mm/1000mm/1000mm, control: Heidenhain TNC 415. An on-site inspection is possible.
Suitable for edge preparation of all types of cutting tools with the corresponding holders and turning devices, e.g. roll cutters turning devices, e.g. cylindrical milling cutters, saw blades up to 380mm diameter, shank tools, indexable inserts and saw band coils up to 750mm diameter. Number of units: 1, table pitch circle: 600mm, table outer diameter: 800mm, machining width/height: 180/ 250mm, feed rate: 0.5-6m/min, flakkotier power: 4kW, connected load: 6.4kW, length: 2500mm, width: 1950mm, height: 2500mm, weight: 3t, operational hours counter: approx. 100h. Including documentation, without accessories or spare parts. On-site inspection is possible.
Stations: 6, power: 40kW, control: Siemens. Including upstream Fischer separating head, Festo feeder, material discharge conveyor, Knoll 450K-1 chip conveyor, year of manufacture: 2004, chip preparation with ejector and hydraulic unit. Documentation available. On-site inspection is possible.
A rotary transfer machine for the production of spherical ladles is available. Machining stations: 13, bar loader: 0433, bar loader length: 3000mm, machine power: 40kW, control: Hydromat. Including Bosch hydraulic unit, Knoll 450K-1 chip conveyor, Müller CL206-B lubricant preparation system and separate Knoll chip disposal system. The machine was extended to SW milling in 2015. Documentation available. On-site inspection is possible.
Adhesive: PU (reactive PUR adhesives), material gap height: 0mm-50mm, application speed: 45m/min, working width: 1300mm, weight: approx. 150kg. Documentation available. On-site inspection is possible.
A Weinig four-sided planer including automation, double cross-cut saw, infeed and extraction system is available. 1) Four-sided planer Weinig Hydromat 22 BL with automatic lubrication, year of manufacture: 1987, working width: 220mm, working height: 140mm, number of heads: 7, head arrangement: bottom/right/left/right/top/bottom/bottom, spindle diameter: 50mm. 2) Kellfass automation unit consisting of double cross-cut saw, length: 5000mm, buffer cross conveyor and pneumatic roller infeed. On-site inspection is possible.
Glue type: PUR glue, glue application system: cartridges, max. edge thickness: 25mm, max. workpiece thickness: 60mm, feed rate: 16m/min, min. workpiece length: 140mm, min. workpiece width: 60mm. Including various spare parts and Ligmatec return. Documentation available. On-site inspection is possible.
Three almost identical CNC plastic pipe butt welding machines (mirror welding machines) Hürner are available. Years of construction: 2x 2016 and 1x 2018, working range OD: 40mm-160mm, power: 2.85kW, reduction inserts: 40/50/63/75/90/110/125/140, weight: approx. 80kg. Documentation available. On-site inspection is possible.
max. wheel diameter: 2500 mm gear width: 1200 mm max. module: 32 min. module: 3 total power requirement: 25 kW weight of the machine ca.: 60 t dimensions of the machine ca.: m Gear , min. / max. 180 / 2,500 mm Module 3 - 32 Helix angle, max. 10 - 35 ° Gear width for straight gears 1,200 mm Stroke length, approx. 100 - 1,200 mm No. of strokes 80 - 350 /min Stroke position adjustable 300 mm Stroke speed 4 - 40 mm Max. weight of workpiece, approx. 18,000 kg Min. / max. no. of teeth 16 / 576 Table size x bore 1,400 x 500 mm Grinding wheel Ø, approx. 500 mm Grinding wheel peripheral speed 34 m/s Total electrical load, approx. 45 kW - 380 V - 50 Hz Weight of machine, approx. 60,000 kg Accessories / Special Features: Hydrostatic guides in grinding slide, table and in all other guideways. Completely covered working area with sliding doors. Automatic grinding process for various cycles, with ...
max. wheel diameter: 280 mm max. number of teeth: 100 max. module: 6 min. module: 1 total power requirement: 6 kW weight of the machine ca.: 2500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
spindle diameter: 0 mm x-travel: 700 mm y-travel: 600 mm table length: 800 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Double Column Design Jig Borer Tablesize: 800 x 600mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. dia. of grinding wheel: 800 mm max. width of grinding wheel: 250 mm grinding table: swivable: Grad total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Double Sided Finegrinder, Dresser, Coolant Device, older M. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 0 mm max. number of teeth: 0 max. module: min. module: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m CNC controlled milling machine for synchronous rings The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1020 mm plate thickness: 2,5 mm distance between columns: 1050 mm daylight opening: mm : 135 ° total power requirement: Handbetrieben kW weight of the machine ca.: 0,32 t dimensions of the machine ca.: 1,4 x 0,6 x 1,3 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding range: 8 - 32 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 16 Kg dimensions of the machine ca.: 0,43 x 0,24 x 0,24 m Drill grinding machine: Additional station for grinding back the drilling cutting surface (clearance angle) 25tk. Collets ER 40 are included in the scope of delivery, these are also suitable for clamping intermediate sizes. For grinding twist drills made of HSS and Hard metals with a TiN layer of 8 - 32 mm. Rotor with precision ball bearings guarantees smooth running. Vibration-free running thanks to its heavy weight and rubber feet. Sharpening angle adjustable for all common twist drills. Package dimensions: 430 x 240 x 240mm. Weight 16kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 915 mm plate thickness: 1,0 mm distance between columns: 920 mm daylight opening: mm : 135 ° total power requirement: Handbetrieben weight of the machine ca.: 96 Kg dimensions of the machine ca.: 1170 x 400 x 480 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 2,5 mm roll diameter: 98 mm throat: 160 mm total power requirement: 1,5 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 550x1400x1500 m Delivered with: • hydraulic version • 4 set of wheels • Foot control • Brake motor • Emergency stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding range: 3 -28 mm angle adjustable from - to: horizontal 0-180 Grad angle adjustable from - to: vertikal 0-45 Grad angle adjustable from - to: negativ 0-52 Grad clamping range: 3 - 28mm mm 0: 5200 U/min connected load: 230 / 250 Volt / Watt wheel diameter: 100 x 50 x 20 mm weight of the machine ca.: 45 Kg dimensions: 0,5 x 0,4 x 0,4 m This grinder is ideal for regrinding tools such as end mills, drills, TIG welding needles and much more. comes standard with: Lathe tool accessories Drill accessories Accessories for milling 5C spring collet (4-6-8-10-12 mm) Clutch key 38-42 Grinding wheel wrench Allen key M3-M8 screwdriver Diamond grinding disc Ø 100 x 50 x 20 Grinding wheel: Ø 100 x 50 x 20 Diamond pen Spring collet: 3/16 - 5/16 - 3/8 - 1/2 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 45 mm throat: 230 mm bore stroke: 125 mm spindle taper: ISO 30 spindle turning speed range: 75 - 1600 U/min max. milling cutter diameter: 80 mm : 560 mm : 230 mm table surface area: 800 x 240 mm max. distance between table and spindle-nose: 460 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 320 Kg dimensions of the machine ca.: 1,0 x 0,8 x 1,45 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1270 mm plate thickness: 2,0 mm distance between columns: 1300 mm daylight opening: 48 mm : 135 ° total power requirement: Handbetrieben weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,6 x 0,9 x 1,2 m Segment-bending machine Segment widths: 25, 30, 35, 40, 45, 50, 75, 100, 150, 250 and 260mm. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 40 mm throat: 275 mm bore stroke: 120 mm spindle taper: MK 4 turning speed range: 75 - 3200 U/min : 190 mm : 490 mm table surface area: 700 x 210 mm connected load frequency: 400 V diameter of hob: max. 80 mm total power requirement: 1,1/1,5 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 0,8 x 0,75 x 1,85 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 25 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK 3 spindle turning speed range: 50 - 3000 U/min : 280 mm : 155 mm table surface area: 500 x 180 mm connected load frequency: 230 V max. distance between table and spindle-nose: max. 320 mm total power requirement: 0,8 kW weight of the machine ca.: 150 Kg dimensions of the machine ca.: 670 x 550 x 910 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Wrapper Universum Kasper Model: HWM 50 Squirrel wrapping machine is mobile for all spears such as Kornspitz and pretzel sticks, etc. Universal Winding Machine for all doughs for wrapping Stainless steel version reinforced Dough filler approx. 20 to 400 g 500 mm belt width all belts and scrapers NEW DGUV V3 tested Connection 400V, 1 kW, 16A-CEE plug Used machine overhauled 3 months warranty + spare parts service Option: Feeding belt EB Service Package E-Box Maintenance contract Instruction & Commissioning We have many TOP cone wrapping machines in stock!
Suitable for automatic cutting and surface grinding of hard metal and HSS rods with high precision for standard and special solutions Accessories: Total enclosure,, Automatic feed (hydro-pneumatic),, Rapid traverse adjustable via touch panel, Automatic fire extinguishing system Kraft & Bauer FB 703,, Length positioning freely programmable,, Control system Siemens Simatic HMI,, Preparation for connection to central coolant system., Workpiece diameter with loading magazine: 3 - 20 mm, Workpiece length without loading magazine: 3-32mm, Workpiece length with loading magazine: 3-310mm, Workpiece length without loading magazines: 1-450mm, Spindle speed grinding spindle: 2000 rpm,, mass: approx. 1,700 kg, weight: approx. 1,700 kg, Dimensions L x W x H: 1900 x 1200 x 2400 mm, colour: Gray
Suitable for automatic cutting and surface grinding of carbide and HSS rods with high precision for standard and special solutions. Accessories: Total enclosure, Automatic feed (hydro-pneumatic), Rapid traverse adjustable via touch panel, Automatic fire extinguishing system Kraft & Bauer FB 703, Freely programmable length positioning, Siemens Simatic HMI control system, Prepared for connection to a central coolant system., Weight approx: 1700 kg, Dimensions W x D x H: 1900 x 1200 x 2400 mm, Cutting disc diameter: Max. 200 mm, Drive power grinding motor: 4,0 kW, Workpiece length without loader magazines: 3 - 450 mm, Workpiece diameter without loading magazine: 3 - 32 mm, Workpiece length with loader magazine: 1-310 mm, Workpiece diameter with loading magazine: from 3 - 20 mm
VACUUM STUFFER WITH LOAD LIFTER, HANDTMANN TYPE: VF200B CODE: N80/35 Technical description: Throughput rate: Up to 5.000 Kg/ h Power supply: 380/440 V - 50/60Hz Power: 6,5 Kw Dimensions: 2000 x 1350 x 2200 mm
STUFFER HANDTMANN, TYPE: VF80 AND SAUCE DOSING MACHINE HANDTMANN 6 HEADS Technical description: Stuffer (x2): Handtmann VF 80 (1) ID-1638 TYPE: VF80 10-5N Serial number: 637 Power supply: 380 V, 50 Hz, 9,55 A, 3,55 kW Dimensions: 940 x 900 x 1600 mm (2) ID-1640 TYPE: VF80 N50/35 Serial number: 221 Power supply: 380 V, 50 Hz, 10.85 A, 4 kW Dimensions: 1050 x 700 x 1600 mm Sauce dosing machine, Handtmann ID-1639 Heads number: 6 Dimensions: 2300 x 1050 x 1650 mm
PORTIONER, HANDTMANN MODEL: GMD99-1 Technical description: Serial number: 1052 Power: 220-240 V / 50-60Hz Pression: 7 bar/100psi Bandwidht: 220 mm Dimensions: 1600 x 900 x 1300 mm
STUFFER + PORTIONER WITH SAUSAGE HANGER, HANDTMANN Technical description: Stuffer type: Handtmann VF100B Portioner type: Handtmann AL 242-01 Hanger type: Handtmann 242-16 Power supply: 380-440 V / 50-60Hz https://youtu.be/ZxAf2uRbDf4
A Hobart tray packaging machine is available. Product weight min/max: 40g/5kg. On-site inspection is possible.
A semi-automatic Haver & Boecker bag filling machine is available. Stations: 6, max. bag weight: 25kg, filling capacity: 1600 bags/h, bag formats: Quicklime/hydrated lime/cement/gypsum, grain size: adjustable, control: Siemens S7. The machine was brought up to date in 2025. Documentation available. On-site inspection is possible.
A Hyfra water recooler is available. Cooling capacity: 5.15kW, max. ambient temperature: 37°C, max. operating overpressure: 29.5bar, refrigerant: R 407c, refrigerant capacity: 2kg, machine dimensions X/Y/Z: approx. 900mm/800mm/1400mm, empty weight: approx. 180kg. Documentation available. On-site inspection is possible.
A Winkler + Dünnebier envelope printing machine is available. Envelope type: peel & seal gumming, format range side seam min./max.: 114mm x 150mm/330mm x 450mm, format range center seam min./max.: 114mm x 150mm/230mm x 450mm, paper weight range: 70g-165g/m², production output: 250 envelopes/min. Including vacuum pump and blow air pump. Documentation available. On-site inspection is possible.
Carpentry machine Hundegger k2 625 5 axis year 2003
A coolant separator is available. Volume flow: 4000m³/h, total pressure: 2000Pa, power: 4kW, connection diameter: 75mm, material: stainless steel. Documentation available. On-site inspection is possible.
Hugo Beck Flexo 500 S – Shrink Wrapping Machine Machine details: • Model: Flexo 500 S • Manufacturer: Hugo Beck • Year of manufacture: 04/2006 • Power supply: 400 V / 50 Hz • Power rating: 3 kW • Rated current: 5 A • Location: Dettingen, Germany Description: Robust and reliable shrink wrapping machine from the well-known German manufacturer Hugo Beck. This Flexo 500 S, built in April 2006, is in good and working condition. Ready for immediate use in production environments and suitable for a wide variety of packaging applications.
HAAS VF-1 CNC machining center was built in 2015 in the United States by HAAS AUTOMATION, INC. The machine, designed for unit and small batch production, is the ideal choice for any tool workshop. All this is due to the use of a number of modern components with excellent technical parameters, which guarantee high reliability and precise machining. Workpieces weighing a maximum of 1361 kg are machined inside a large, fully illuminated work area by means of a high-speed spindle and tools taken from a 20-position magazine. The machining process is free of vibration or oscillation, thanks to an extremely stable design made from top-quality steel. All this is complemented by an intelligent CNC control with an intuitive interface. The HAAS VF1 milling center weighs 3539 kg. It is also possible to purchase additional tooling shown in the photos (tool holders, vices, TSCHORN 3D tester, measur ...
Grinding length 500 mm Grinding width 230 mm Table size 760 x 200 mm Automatic delivery Magnetic disk Filter system
Paper drill Hang 106DTK4, machine number 62407, in good condition, immediately available
Packaging line for the production and packaging of wet wipes, e.g. hygiene wipes, cleaning wipes, baby wipes, disinfecting wipes. The production process includes unwinding of the nonwoven from the jumbo roll, slitting for a 2-lane production process (until packaging), dipping into liquid, longitudinal folding in Z- or W-fold, cross cutting (tissue length), 1 x cross folding, stacking, continue to packaging unit which handles film feeding and wrapping wet wipes, punching the hole (to open the pack), positioning of reclosable label, bag cutting/heat sealing. Integrated splice units increase efficiency during material, film and label role changeover. - Specifications: suitable for dry nonwovens (airlaid, spunlaid) | folds: Z or W shape (change of folding tool necessary) | fold face adjustable per side | dimensions of folded tissue: L(70-100)xW(40-100) mm | dimensions of unfolded tissue: L(1 ...
Packaging machine for the production and packaging of wet wipes, e.g. hygiene wipes, cleaning wipes, disinfection wipes. The production process includes folding and cutting the wipes, moistening with one or more different liquids, packaging the wet wipe in a 3-side sealed or 4-side sealed pouch. Production of up to 4 chain bags possible. Included is a dosing pump, a perforating tool, a tear notch tool, 2 character sets for cold and hot printing (14 characters each), an outfeed belt (1,2m). SIEMENS PLC and Touch-Monitor. - Specifications: Bag sizes: L(50-125)xW(50-110)mm | suitable films: PET, OPP,BOPP ,AL, PE, CPP, laminated films | suitable for dry nonwovens (airlaid, spunlaid) | folds: max. 10 folds vertically and 4 folds horizontally | size of tissue, unfolded:L(40-220)xW(30-240)mm | Grammage wet wipe: 30-80g/m? | max. roll diameter: nonwoven: 1000mm, film: 350mm | filling range liqui ...
Packaging line for the production and packaging of wet wipes, e.g. hygiene wipes, cleaning wipes, baby wipes, disinfecting wipes. The line is constructed from a wet wipe production unit and a flow wrap unit. Wet wipes production process: Unwinding of the nonwoven from 2 jumbo rolls and slitting into 5 lanes per roll (until moistening) for a fast production method, longitudinal folding in Z or C-shape, moistening via several spraying nozzles, cross cutting (wipes length), stacking and forwarding to the packaging unit. The flow wrapping unit handles: feeding the wet wipes, feeding the film and printing (hot stamping), hole punching (to open the pack), positioning the reclosable label and e.g. a seal label (the integrated 2-lane labeler allows offset labeling), bag cutting/heat sealing. The liquid supply system for moistening the wipes consists of 2 tanks with continuously mixing agitators ...
maximum number of results exceeded
please refine your search
