126,693 used machines on RESALE, but how to find them? Machine Search
; Accessories: 20FT Generator Set Container, Outside dimensions: 606x244x259, Internal dimensions: 575x226x237 (door height 230 & door width 220)
Mesh Welding Machine Width: 1200 mm Length: 2000 mm Suitable for: Industrial products Consist of: -double magazine -line wire magazine of 2000 mm
PLC – controlled (touch screen) multifunctional press with multiple functions Firstly, our multi-function press is a vacuum press, three-dimensional film deformation with or without membrane. Vacuum chamber size 2,340 x 1,340 mm Maximum workpiece height 60 mm Equipped with a vacuum diaphragm at the top and bottom. The press is equipped with a powerful vacuum system and a vacuum tank, which guarantees a constant and uniform supply of vacuum to the working chamber. Drive power vacuum pump 4.5 kW Vacuum tank volume 500 liters Vacuum pump flow rate 100 m³/hour Two pieces of air heat exchanger, each with a heating capacity of 3 kW. Secondly, our multi-function press is a hydraulic plate press with ten pieces of press cylinder and 200 tons pressing force – Suitable for different applications - - Cold and hot pressing - Single-sided and double-sided veneer pressing ...
CATALOG NO. 7240 TECHNICAL DATA - inlet width 400mm - inlet height 210mm - shaft width 530mm - shaft diameter 500mm - knife length 530mm - number of knives 2 pcs - sieve dimensions 55x50mm - 2 geared rollers pulling from the bottom - lower shaft motor approximately 3kW - toothed shaft pulling from above - upper shaft motor 1.5kW - length of the feed belt 4600mm - feed belt width 400mm - main engine 55kW - autoreverse - feeder dimensions length/width/height 4630x620x760mm - machine dimensions length/width/height 2510x1700x1200mm - weight approximately 3500 kg – German production – used chipper, very good condition The prices given are net prices. Net price given for international transactions, EX, customers from the EU with an EU Tax Identification Number. Current offer on our website. Net price: 85,900 PLN Net price: 19089 EUR depending on the price 4. ...
Swash-up machine: 2-deck machine: 3.6 m2 / deck product-contacted parts in stainless steel 1.4301 ( AISI ) 2 x Ball knock cleaning Safety clamping screws Lifting device incl. 2 x sied, mesh size as desired: from 0.1 - 5 mm Height of the machine without frame: 1620 kg Weight: 1820 kg. --> Machine completely grounded.
Diosna SP 240 A DL with 3 bowls -Machine after overhaul - New bearings, new V-belts, new switches, new buttons, - 2 speed - 2 o'clock for 30 minutes - 3 boilers - For 240 kg dough
Used automatic packaging line by MIFLEX-MASZ model SP-200, new 2014. Automatic packaging line (recently used for packaging herbs and teas in shaped sachets) with automatic packaging in doypacks. Can also be used for other types of assortment. It consists of a packer, sachet packer with feeder and dispenser. Built on a self-supporting frame with protective covers. Equipped with independent temperature control of each sealing jaw and infinitely variable speed control. Emergency conditions are visualised on the control panel . All product contact parts are easy to dismantle for cleaning and replacement, made of P.Z. H. certified materials. Sachet dispenser AS-20 Equipped with : - unwinding of the packaging material - guide roller system - volumetric dispenser with adjustable portions - sealing system - shaped sachet punching system - control cabinet - main drive with adjustab ...
Jetzone furnace Manufacturer: CPM WOLVERINE PROCTOR Ltd. Model: SND 1.5 x 202 Year: 2016 Productivity: 450 kg / h Dimensions: 8136 x 3581 x 4376 Heating medium: natural gas Description: A high-speed dryer consisting of two main elements: a fitting equipped with heating and distribution elements, and a production conveyor.
Table diameter 2.000 mm Working diameter 2.000 mm Machine under retrofit/rebuilding to install CNC Mechanical ready, totally rebuilt.
- Compensator compensator MWM 12304761 - Please note! Price per piece! - 12304761 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new technologies and proc ...
- Compensator Compensator MWM 12300811 Original - Suitable for several motors - Please note! Price per piece! - 12300811 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting a ...
Key data: 400 , 64 , 30
Manufacturer: Arburg Type: 270C 400 - 100 Built: 2000 Control: Selogica Closing force: 400 kN Closing type: Hydraulic Tie bar distance: 270 mm x 270 mm Plate size: 446 mm x 446 mm Tool installation height: min 200 mm Opening distance: 350 mm Plate spacing max.: 550 mm Screw: 30 mm Lifting volume: 70 cc / 64 gram hp Spray pressure: 1550 bar General Engine: 11 kW Heating: 5.9 kW Dimensions: 3.42 m x 1.5 m x 1.7m Weight: 1980 kg Screen text: German Additional equipment Core train: x1 Robot interface
ID3182 2 piece Strödter Vigomat VP 250-2,5 year/Year of construction 2013 articulated manipulators, pneumatic power supply Load capacity 240 kg Max. Max. load torque on load handling attachment 1200 Nm Max. Horizontal working range: Radius R 3.7 m Max. Stroke: 1.45 m Max. Max. lifting speed: 0.8 m/s Type of attachment Pedestal Weight of device 755 kg Noise emission < 70dB Pneumatic working pressure 6 bar Max. Air consumption: max 40 NI /double stroke Diameter of main cylinder 200 mm Buckling manipulators, power supply pneumatic Load capacity 240 kg Max. load torque at the noise pick-up device 1200Nm Max. horizontal working range: Radius R 3.7 m Max. stroke: 1.45 m Max. lifting speed: 0.8 m/s Fastening type of pedestal Weight of the device 755 kg Noise level < 70dB Pneumatic working pressure 6 bar Max. air consumption: max 40 NI /double stroke Diameter master ...
Key data: 500 , 130 , 35
Manufacturer: Battenfeld Type: BA 500/210 TM Built: 2000 Control: Unilog B2 Closing force: 500 kN Closing type: Knee lever Tie bar distance: 320 mm x 320 mm Plate size: 490 mm x 490 mm Tool installation height: min 150 mm max 350 mm Opening distance: 250 mm Plate spacing max.: 600 mm Screw: 35 mm Lifting volume: 144 cc Spray weight PS: 130 gram PS Spray pressure: 1500 bar General Engine: 11 kW Heating: 10.4 kW Dimensions: 3.3 m x 1.1 m x 1.7 m Weight: 2500 kg Screen text: German / English Additional equipment Robot interface Core train: x1
SHARK 281 CCS (Cut Control System) manual bandsawing machine to cut from 0° up to 60° left. Other than the manual cut mode, the sawing machine can make single cuts without operator, using the head weight control- led by a hydraulic brake: after the cut the band stops. The frame at this point is manually lifted to the position needed in order to reposition the bar to cut . In the version with pneumatic vice (MA) the vice is opened/clo- sed by a manually-controlled valve (optional with pedal control). BEST PRICE IN EUROPE
- Oil cool oil cooler 12302852 MWM - Suitable for several motors - Please note! Price per piece! The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new techno ...
SHARK 281, manual band sawing machine to cut from 0° to 60° left. A FEW FEATURES: Electric panel (wiring totally identifiable, stand-by, loose-key safety switch, main switch, pole change switch, emergency stop, motor magneto-thermal overload, minimum tension coil, protection against missing phase, low tension safety device (LTSD 24 V).- IP55 control handle. BEST PRICES FOR ALL MEP MACHINES IN EUROPE! ASK FOR A QUOTE
- Compensator Compensator MWM 12300319 - Suitable for several motors - Please note! Price per piece! - 12300319 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integr ...
- Mixture pipe MWM 12301623 - Suitable for several motors - Please note! Price per piece! - 12301623 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new t ...
Inverter for ENGEL robots Acopos Multi PO 220 Acopos Multi CO160
Alligator scissors TR250: • Four-sided knives usable • Opening width is continuously controlled via foot pedal Technical data: Total dimensions: 1100 x 700 x 1200 mm Total weight: approx. 350 kg Knife length: 250 mm Max. knife opening: 150 mm Cutting force: 350 kN Cutting power: Round iron 22 mm (ST 37) Main drive: 3 phases: 4 kW (5.5 hp) Cutting strokes p/min: up to 17 / min
- Bracket bracket MWM 12300514 - Suitable for several motors - Please note! Price per piece! - 12300514 - References: 12300515 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly ada ...
- Exhaust gas bend exhaust manifold MWM 12304038 o. 12300448 - Suitable for several motors - Please note! Price per piece! - 12304038 o. 12300448 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. ...
Spreading attachment PIETSCH STA 1.7 MW series 2000, capacity 1.7 m3, conveyor belt, tarpaulin folding roof, spreader rubber, drive via vehicle hydraulics, with remote control and support supports. Sale as is or in parts possible.
1 MONTI ANTONIO continuous belt press for knitted fabric ironing/finishing, with steaming upper plate type 205
- Gas mixing valve MWM 12301147 - Suitable for several motors - Please note! Price per piece! - 12301147 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating ...
- Air guide housing air duct housing MWM 12141695 - Suitable for several motors - Please note! Price per piece! - 12141695 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapti ...
Complete gate line , with log task - Remote controlled clamping car - Gate Müller with sideware crosscut saw, complete mechanization, cut saw Paul S900 SH 180 mm, sour paul KME II /1000, chopping system Rudnick&Enners 200/600 etc...
JUNGHEINRICH ETV 214 in original factory paint unpainted. Tecnicaly in excelent condition Height of lift 2200mm Lifting capacity:1400kg Lifting height: aprox 4400mm Side move:yes Perfect working condition
- Mixing pipe mixture line MWM 12301281 - References: 12300476 ; 12300650 - Suitable for several motors - Please note! Price per piece! - 12301281 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new proje ...
Great working condition Gel battery from 2016 Forklift will be new painted
Pacage set of REHM TIG WELDING MACHINE Welding torch 10m welding gun covers 3 different sizes look photos Suitcase for the complete set included Gun for electrode mma welding
4 pcs Bronze guide bush - column die-casting machine, D 250mm, Idra, Oleopress, new Special price - You only pay the raw material costs! We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition! The part was bought from a spare parts warehouse of a company, has never been in operation, is in a completely mint condition. Suitable for the columns of the die-casting machines D 250mm from Oleopress and Idra. Weight approx. 20 kg - Outside diameter 271/278/265mm - Inner diameter 250mm - Tube length 275mm Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D300
4 pcs. Bronze collar bushing - column die-casting machine, D 250mm, Idra, Oleopress, new Special price - You only pay the raw material costs! We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition! The part was bought from a spare parts warehouse of a company, has never been in operation, is in a completely mint condition. Suitable for the columns of the die-casting machines D 250mm of the company Oleopress and Idra. Weight appr. 20 kg - Outside diameter 278/271mm - Inner diameter 250mm - Tube length 250mm Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D30 ...
Grain mill grinding turbine Stone mill for cereals, legumes and spices Table machine wood Grinding stone made of corundum ceramic Power: about 200g /minute Grinding degree: Infinitely adjustable from very fine to coarse Funnel frame approx. 1.3 kg cereal Connection 220V, 600 watts Dimensions: 208 x 242 x 380 mm, WxDxH Visit our Milbrandt Outlet with show bakery!
Eccentric screw pump with funnel Power: approx. 15-20m3 per hour Infinitely adjustable with adjustable motor Dimensions and weight: Length: 3100 mm Width: 820 mm Height: 1300 mm Engine data s. Photos
Grain mill grinding turbine Stone mill for cereals, legumes and spices Table machine Grinding stone made of corundum ceramic Power: about 200g /minute Grinding degree: Infinitely adjustable from very fine to coarse with built-in cooling fan Funnel frame approx. 1.1 kg cereal Connection 220V, 600 watts Dimensions: 190 x 220 x 380 mm, WxDxH NEW Machine Visit our Milbrandt Outlet with show bakery!
- Cover Sealing Lid MWM 12325921 - Suitable for several motors - Please note! Price per piece! - 12325921 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating ...
Radial drill Soraluce TR3-2500mm. 2500mm arm. Drilling in steel: 80mm. Drilling in cast iron: 100mm. Chuck spindle diameter: 110mm. Cone Morse 6. Speeds: 16 (20-1475rpm). Engine power: 10hp.
Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2800 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 30% ED at 280 amperes 60% ED at 210 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 4-wheel drive DV 26 Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 80 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box, kpl ...
The small rotary tablet press SPT-TPL 200 (small scale production); Touch screen, PLC control platform; HMI system; Bczkcapdbh The machines comply with the requirements of the GMP guidelines and are CE certified; Number of stations (Max.) D=13 B=16 BB=19 1 Max tablet ejection/hour T/h 46 000 57 000 68 000 2 Max.Tab.Diameter Round mm 25 16 13 Shape mm 25 19 14 3 Max tablet thickness mm 8.5 4 Max main pressing force t 5 5 Max pre-press force t 1 6 Dimensions mm 600 x 1106 x 1705
Pester Pewo pack 250 compact The basic machine PEWO-pack 250 compact comprises the following assemblies (standard equipment): - Degree of protection : IP54 (ST) - Control cabinet : Swivel - Proximity Switch : Wenglor (ST) - Pneumatic version : Pneumatics (ST) - Traffic light indicator : Tricolor (ST) - Electrical version : Electrical standard S rev 15 - Frequency converter : Lenze (ST) - Product feed : straight in the middle Specifications: - Control unit HMI - Type : HMI 15" Pester Tangius (ST) - Control : Elau PacDrive - Voltage : 3x400V+N+PE, 50 Hz/60 Hz - Operating side : right - Protective cover : Acrylic glass (ST) - Paintwork : VA - Design (ST) - Packaging material - film : PE flat film - Documentation - Language : 2x French+1x CD - Documentation - Execution : Standard - Documentation - Supplier : 1x (ST) - Validation : Standard - Machine marking : F ...
Trapeze Punch / Croissant Fritsch Bakery Machines -Built in 2007 -Type trapezoid 270/50x90 6R
Continuously working melt filter New and unused machine Visit possible by arrangement.
Various strand granulators are for sale - Strand granulator SG-200; 150; 100; 50 mm cutting rotor width All machines are connected and ready for testing. Visit possible by arrangement.
- Air guidance air duct MWM 12136627 - Suitable for several motors - Please note! Price per piece! - References -> 12131031 – 12136628 – 12306646 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new pro ...
TO WHOM IT MAY CONCERN ; WE VE NEW UNUSED 2 SETS VULCAN COUPLINS. AT STOCK. VULKAN HERNE 2 GERMANY 5G 2701050M ( TOTAL 8 PCS ) IF YOU VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US . Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 90 Mobile: +905556084850 aliagamarine.com TURKEY
- Air guidance air duct MWM 12131039 - Suitable for several motors - Please note! Price per piece! - References -> 12131070 – 12350043 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By cons ...
- Cover Lid MWM 12141950 - Suitable for several motors - Please note! Price per piece! - References -> 12141951 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integr ...
CNC Lathe Gildemeister CTX 200 Series 2 Immediately free from location: CNC Lathe Gildemeister Type CTX 200 Series 2 Built in 2001 Operating hours 39,000 CNC Control Heidenhain 4290 TP Turning diameter 210 mm Turning length 305 mm Reiststock revolver 12 driven tools Conveyor Bar loading magazine Max travel plan 160 mm Max travel length 350 mm Spindle speeds up to 5000 rpm 2 simultaneous axes with C axis 1 controlled spindle 12 driven tools Collet pliers with hydr. Hollow clamping device up to 43 mm Workpiece pick-up device up to 56 mm very many tools
maximum number of results exceeded
please refine your search
