gearbox used for sale

Geared motor BONFIGLIOLI, SIEMENS 73.4 rpm motor: 1LA7080-4AA11 0.55 kW 1395 rpm 230 / 400 V 3AC 50 Hz 60 Hz - operation is possible ! IP55 gearbox: VF 63 P1 P80 B5 ( VF63P1P80B5 ) i: 19 Hollow shaft diameter: Ø 25 mm wavelength: 120 mm groove width: 8 mm 2x Flange diameter: Ø 75 / 110 mm, bolt circle diameter: Ø 90 mm 8x Threaded hole: M8 x 1,25, Depth: 15 mm Intermediate flange diameter: Ø 115 / 180 mm, Bolt circle diameter: Ø 147 mm 4x Hole diameter: Ø 11 mm Motor and gearbox: Aluminium housing New ! Dimensions: 420 x 220 x 250 mm

Entire coextrusion line consisting of: - Bandera extruder 80 - 20 L / D - 60 kW, 400 V - year 1969 - variable V gearbox - Bandera extruder 80 - 20 L / D - 60 kW, 400 V - year 1965 - mechanical gearbox - 700 mm coextrusion table - Towing cutter, oven, Tecnofar exit tunnel with hydraulic variators - Omipa calender width 1000 mm with hydraulic variators - year 1976

Extruder is missing electronics and it is not in running condition. Barrel 30D The barrel was opened for inspection of the liners and shafts, the hydraulics function correctly. Liner 1. Feed, 2.5D good condition Liner 2. Inter, 5.0D good condition Liner 3. Inter, 5.0D good condition Liner 4. Inter, 5.0D good condition Liner 5. Inter 5.0D good condition Liner 6. Inter 2.5D good condition Liner 7. XLT Discharge 5D good condition. Feed and return lines were removed and compressed air fed into circulation blocks. All blocks were found to have good flow. Pipework is in good condition with all solenoids present. All control thermocouples and melt thermocouples are in place but could not be tested due to condition of electrics. All the heaters are in place but could not be tested due to the condition of electrics. The barrel is in very good overall condition. Shafts Al ...

Installation kit, shaft gearbox, gearbox HARMONIC DRIVE ANTRIEBSTECHNIK series CPL-2A CPL-17A-120-2A-SP article number: 1021350 series: CP l Size: 17A reduction ratio: 120 version: 2A Special version: SP Speed: max. 10000 rpm Rated torque : 24 Nm Shaft diameter: Ø 18 mm flange diameter: Ø 60 mm New, with backings ! Dimensions ( packaging ): 260 x 100 x 95 mm

Installation kit, shaft gearbox, gearbox HARMONIC DRIVE ANTRIEBSTECHNIK series CPL-2A CPL-17A-120-2A-SP article number: 405764 series: CPL > Size: 17A

Installation kit, shaft gearbox, gearbox HARMONIC DRIVE ANTRIEBSTECHNIK series CPL-2A CPL-25A-100-2A article number: 405770 series: CPL Size: 25A Reduction ratio: 100 Version: 2A Speed: max. 7500 rpm Rated torque : 67 Nm Shaft diameter: Ø 26 mm flange diameter: Ø 85 mm New, with backings ! Dimensions ( packaging ): 360 x 140 x 95 mm

Installation kit, shaft gearbox, gearbox HARMONIC DRIVE ANTRIEBSTECHNIK series CPL-2A CPL-25A-120-2A article number: 405771 series: CPL Size: 25A Reduction ratio: 120 version: 2A speed: max. 7500 rpm rated torque : 67 Nm shaft diameter: Ø 26 mm flange diameter: Ø 85 mm New, with backings ! Dimensions ( packaging ): 360 x 140 x 95 mm

Installation kit, shaft gearbox, gearbox HARMONIC DRIVE ANTRIEBSTECHNIK series CPL-2A CPL-32A-100-2A article number: 405774 series: CPL Size: 32A Reduction ratio: 100 version: 2A speed: max. 7000 rpm rated torque : 137 Nm shaft diameter: Ø 36 mm flange diameter: Ø 110 mm New, with backings ! Dimensions ( packaging ): 325 x 185 x 125 mm

Installation kit, shaft gearbox, gearbox HARMONIC DRIVE ANTRIEBSTECHNIK series CPL-2A CPL-32A-120-2A article number: 405776 series: CPL Size: 32A Reduction ratio: 160 version: 2A speed: max. 7000 rpm rated torque : 137 Nm shaft diameter: Ø 36 mm flange diameter: Ø 110 mm New, with backings ! Dimensions ( packaging ): 325 x 185 x 125 mm

Make: MTU Diesel Motor Type: 16V2000 Built year: 1999 Power: 1202 kW Speed: 2230 RPM Quantity: 2 Nico Gearbox Marine engine with gearbox in very good condition. Contact us at infoheeyas.co.uk #mtu #engine #marine #vessel #nico #propulsion #sea #power #energy #ship #shipengine #diesel #dieselengine #gear #boat

SANTANDREA DUAL SHAFT HYDRAULIC SHREDDER, Type H50 130, very good conditions, Shafts length 1.300 mm, with top hydraulic ram, 50 mm.knives - 1 hook + spacers + cleaning teeth, Air/oil heat exchanging unit, Shredding chamber mm. 1.300x900), Electric motor 37 kW 400v 50hz, Hydraulic power station, Electrical control panel, Loading hopper, CE compliance, Users manual, electrical drawings, very sturdy structure, The rotation of the shafts is determined by 2 reduction stages composed by 1 gearbox with 2 large gears in an oil bath + 1 planetary gearbox., St.Andrea are longlasting machines, width: 1.300 mm. (51.18), Power: 37 kw

FU 1600 SERVO 1600x500 Console Metal Milling Machine, Industrial Universal Multi-Purpose Cantilever Drilling Milling Machine FU 1600 SERVO 1600x500 Console Metal Milling Machine, Industrial Universal Multi-Purpose Cantilever Drilling Milling Machine Professional metal milling machine FU 1600 SERVO - available from stock! We present to you a professional, versatile, multi-purpose metal milling machine FU 1600 SERVO. The universal, industrial milling machine FU 1600 SERVO is a large, solid and stable machine, which, thanks to its precision and reliability, is designed for professional metalworking in both large and medium-sized enterprises, and thus satisfies even the most demanding customers. The professional FU 1600 Servo milling machine meets all safety and quality requirements. Brand: VIBER-SYSTEM Model: FU 1600 SERVO Table size: 1600x500mm Table load: up to 1800 kg Nu ...

ID3105 Löffler Stone block saw / Steinblocksäge year/Year of construction 2008 Stone block saw, saw blade diameter 2000mm, cutting height 80cm. Track length 20m, cutting length 3300mm. Sold without turntable. Engine power 75kW FU controlled.gearbox 2021 overhauled, engine year 2021 new, support height & side new guided and stored 2023. Stone block saw, saw blade diameter 2000mm, cutting height 80cm. Track length 20m, cutting length 3300 mm. Sold without turntable. Motor power 75kW FU controlled. Gearbox overhauled in 2021, engine built in 2021 new, support height & side rerouted and mounted in 2023

Description/name of the machine: Console drilling and milling machine for metal Manufacturer: VIBER-SYSTEM Model: FU 1600 SERVO Year of production: 2023 Condition: New FU 1600 SERVO 1600x500 Console Metal Milling Machine, Industrial Universal Multi-Purpose Cantilever Drilling Milling Machine Professional metal milling machine FU 1600 SERVO - available from stock! We present to you a professional, versatile, multi-purpose metal milling machine FU 1600 SERVO. The universal, industrial milling machine FU 1600 SERVO is a large, solid and stable machine, which, thanks to its precision and reliability, is designed for professional metalworking in both large and medium-sized enterprises, and thus satisfies even the most demanding customers. The professional FU 1600 Servo milling machine meets all safety and quality requirements. Brand: VIBER-SYSTEM Model: FU 1600 SERVO Table  ...

total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m 6-axis industrial robot YASKAWA MH50 2 CNC rotary tables 1. rotary table 1 and rotary table 2 limited Nmax=1.300 1/min Reduction ratio I= 1:72 Nmax: Reduction ratio and Nmax motor corresponds to 120°/sec on the table Mdnenn. Output = 828 Nm Maximum centric loading weight = 15 kN Centering force from inside to outside clamping = 7,540 N @ 6 bar Centering accuracy in the gripper = 0.05 mm [PA] Rotary field restriction depending on cable and hose situation Provided for ± 720° (provide for this in the robot controller) Motor: YASKAWA SGMRV-20ANA-YR11 Milling spindle: AMTRU (CH), type Flexicut 250 Gearbox: ZAE Hamburg, type: S100B-1300/65-HOX-72.0:1-3000 Version: with Yaskawa servo axis + ZAE worm servo gearbox The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Make: MTU Diesel Motor Type: 16V2000 Built year: 1999 Power: 1202 kW Speed: 2230 RPM Quantity: 2 Nico Gearbox Marine engine with gearbox in very good condition. Contact us at infoheeyas.co.uk #mtu #engine #marine #vessel #nico #propulsion #sea #power #energy #ship #shipengine #diesel #dieselengine #gear #boat

Geared motor, three-phase motor with gear LENZE SDSGAXX056-22 n: 413.5 rpm gearbox: SPL62-1NVCR i = 6, 75 Motor: SDSGAXX056-22 0.24 kW 2790 RPM 230 V 3 AC 100 Hz IP54 Shaft Diameter (Gearbox): Ø 14 mm wavelength: 30 mm groove width: 5 mm flange diameter: Ø 62 / 40 mm bolt circle diameter: Ø 52 mm 4x Threaded hole: M5 x 0.8, depth: 15 mm used, tested ! Dimensions: 280 x 90 x 140 mm

HIWIN HS22XD2YM2-1250-0550NNR-X 2-axis system X-Y X-axis: Profile width: 60mm Feed Constant: 155mm Timing Belt Axis Stroke/Overall Length: 1250mm/1775mm Slide: Type L, length 330mm Drive: prepared for gearbox g700-P44(Lenze) Wheelbase: 676mm-incl. Spacing Profiles Synchronous shaft: DM: 50mm - with couplings Y-axis: Profile width: 60mm Feed Constant: 155mm Timing Belt Axis Stroke/Overall Length: 550mm/976mm Slide: Type M, length 230mm Drive: prepared for gearbox g700-P44(Lenze) The gantry system is unused and has not yet been unpacked. Year of construction 07.2023

Type: SRM 125/4000 Parameters: 1250 mm, 4000 mm Manufacturer: Škoda Year of production / SO / GO: - / - / 2020 Description: Machine after complete overhaul. The design of this lathe enables both piece production and small series production, roughing and precise finishing work, turning of threads, cones, internal and external radii, turning of shaped rotary workpieces in CNC control. The drive box of the spindle drive has 3 mechanical stages by means of hydraulic cylinders with switchboards - valves controlled from PLC. A fixed 1: 3 gear ratio is provided in front of the drive box to increase the torque by means of a toothed belt. An emergency brake is located on the input shaft of the drive box. SIEMENS 1PH7 39kW main motor with stepless speed control in a given mechanical stage. The longitudinal movement of the machine support Z axis is a ball screw axially preloaded in ZARN type  ...

Key data: 172 mm

We offer directly on behalf of the owner : Twin-screw extruder Make : COPERION ( Werner & Pfleiderer ) Gearbox make : P.I.V Type : ZSK 170 W 1920/1750 Year of construction : 2021 / 2002 / 1986 Screw diameter : 172 mm Screw speed : 4,9 - 49 min-1 Max. torque : 17,500 Nm Main engine : 216 kW In the last 3 years, a total of over €420,000 has been invested in new components and factory overhauls (some of which were previously unused) The extruder was in use until Aug / 2023 and has already been dismantled ready for transport. The components are partly redundant and date from the years 1986 - 2021. The scope of delivery consists of : Twin screw degassing Coperion DSE 180 - 1 x year of manufacture 2021 ( 180 t€ ) Main gearbox P.I.V - 1 x year of manufacture 2002, factory overhauled ( 233 t€ ) in 2021, unused - 1 x year of manufacture 1986, factory o ...

ID3259 Doppstadt DW2560 BK Bison year/Year of construction 2003 approx. 8130 hours/hours 28 t Wood shredder, screening system new approx. 1200 hours ago, gearbox overhauled and shaft replaced approx. 1200 hours ago Wood shredder, screening plant new approx. 1200 hours ago, gearbox overhauled and shaft renewed approx. 1200 hours ago

Gearbox, planetary gear for hydraulic motor, axle drive, gear axle drive, wheel drive, double planetary gear -Manufacturer: Trasmital Bonfiglioli, wheel drive -Type: 601R1L10BC5DODHP011 -Translation: 1 : 5 -Torque: 3000 Nm -Dimensions: see photos / technical drawing -Number: 20x gearbox available -Price per piece -Dimensions: Ø 262 x 270 mm -Weight: 42 kg/piece

ID3268 OJ TM11/14 year/Year of construction 2001 approx. 9200 hours/hours Piling device, carrier device SR35 T, Deutz engine (400 KW) overhauled 500 hours ago, with vibrator MRZV 925 VS, with VDW gearbox, optional MDBA 3200 (built in 2014) available Piling rig, carrier SR35 T, Deutz engine (400 KW) overhauled 500 hours ago, with vibrator MRZV 925 VS, with VDW gearbox, optional MDBA 3200 (model year 2014) available

Description: Machine information : Machine on: 18573 h Running time: 6735 h Cutting time: 6460 h CAPACITIES X axis travel: 1300 mm Y axis travel: 650 mm Z axis travel: 600 mm Table surface: 1450 x 650 mm Table load capacity: 1300 kg Distance spindle nose to table: 125-725 mm Distance table/floor: 900 mm SPINDLE Drive system: GEARBOX Spindle speed: 6000 rpm Spindle nose: BT 50 Motor power (continuous/30 min): 15/ 18.5 kW Motor torque: 381 Nm MOVEMENTS Rapid feeds for X / Y / Z axes: 30/30/24 m/min Working feed (cutting): 10 m/min Ball screw dimensions: diam. 45 x pitch 10 PRECISION (VI 3441) Positioning (P): 0.012 mm Repeatability (Ps): 0.006 mm TOOL MAGAZINE Tool changer: RANDOM Magazine capacity (standard): 40 tools Max. tool diameter (adjacent pocket empty): 80 (150) mm Maximum tool length: 300 mm Maximum tool weight: 15 kg OTHER Compressed air requir ...

Conveyor belt Svedala Brand: Svedala Sv5: A.A length = 6,000 mm, belt width: 650 mm Propulsion: Hydraulic motor Sv6: A.A length = 7,000 mm, belt width: 650 mm Drive: 4 kW slip-on gearbox Sv7: A.A length = 6,000 mm, belt width: 800 mm Drive: 4 kW slip-on gearbox

SCM machining centre model RECORD 220 : - Useful axis stroke 3250 x 1300 x 300 mm - workpiece useful passage 320 mm - 3180 x 1250 mm multifunctional worktop - 3+3 reference stops for pendulum machining - Becker vacuum pump of 250 mc/h - Centralized automatic lubrication - NUM 1040 electronic control, with Alphacam software - machine according to CE standards, with bumpers and perimeter protections - year of production 1998 - Machine weight kg 8100 Operating units: - vertical electrospindle with inverter 900 – 18,000 rpm, ISO30 connection, with 4th VECTOR rotary axis, served by an on-board tool changer 10-position (RAPID 10) - drilling unit with vertical axis with independent control and encoder, and with 39 spindles as follows: 15 vertical spindles on X-axis 14 vertical spindles on Y-axis 2+2 horizontal spindles on X-axis 3+3 horizontal spindle ...

GK 260N Mixer Manuf.: Werner & Pfleiderer Rotor type ZZ2 Type N tangential Ram Pneumatic pressure 10 bar Camber volume 255 litres Useful volume 220 litres Grease lubrication Dust seal lubrication Stainless steel hopper replaced in August 2011 Pneumatic ram replaced in May 2022, New piston rods, sealings Gearbox Coupling shafts between the mixer and the gearbox Hydraulic central unit With Grease and Oil lubrication pumps The machine was used on natural rubber, NBR and EPDM

Horizontal batch mixer with 630 l. gross content, pneumatic outlet flap (new cylinder), 37 kW engine, Flender gearbox (N2 = 58.58 UPM) and carbide-armoured mixing tools. Workshop overhauled in 2016; very good condition.

Horizontal batch mixer with 630 l. gross capacity, pneumatically operated discharge gate (new cylinder), 37 kW drive, Flender gearbox (N2 = 58,58 RPM) and hard metal plated mixing tools. Refurbished in 2016, very good condition.

1 x Farrel Bridge four roll inclined Z formation Calender Year: 1956, Roll dimensions: 710mm dia. x 1675mm wide, Peripherally drilled rolls for heating/cooling, Drive configuration: 250 HP DC v/s motor through unidrive gearbox Roll differentials: 1&2 15%, 2&3 3%, 3&4 3% No. 4 bole speed Max 75m/min Main and auxiliary bearings: Bronze Bush type, Bearing lubrication: Re-circulating oil. Roll heating: High pressure hot water 17 bar capacity. Cheek material guides rolls 1 & 2: Fully adjustable width using 0.75 kW motor. Cross axis – yes (roll 4). Motorised roll nip adjustment – Roll adjustment 1, 2 ,and 4 – 3.75kW motors – Cross axis adjustment roll 4 – 3 kW motor, max adj. 50mm. Hydraulic pull backs – max pressure 70 bar.

1 x Farrel model F270 Banbury internal mixer, Machine number: 98M5007, Year July 1998, 270 litre capacity, 2 wing rotor design, FYH type dust seals, Hydraulic drop door with linear actuator, Process oil system, Pneumatic hopper. with David Brown unidrive gearbox, serial no GS50277, Leroy Somer Type LSM54 L76P 1492kW AC motor, Dec 2001, RPM 1000/1200, 750V (includes 11kv > 750v transformer). Output rpm 49.8/43. Alstom \Syncdrive\ AC variable speed drive controller, 1940 KVA, 750V, digital drive new in 2001. With Siemens S5 Control system. In feed conveyor and dust extraction system also for sale if required. Spare refurbished Leroy Somer motor also available. Complete and in good condition (still installed at a factory in UK).

1 x Smit 660mm dia x 2100mm wide two roll mill, Rebuilt 2005, manual nip adjustment, Lunn type safety bars, Back roll surface fluted, Front roll smooth finish. Bush type bearings with flood lubrication, compact \Jahnel\ right angle drive gearbox. with 180KW DC variable speed motor and controls. Strip knives to front roll. Heavy duty 2 part bedplate. Extra Information: Front roll 29 teeth Back (fluted roll) 32 teeth Friction ratio 1:1.1 Motor 180kW DC variable speed, 1300rpm, Gear box ratio 1:9.8 Bullgear 122 teeth, Pinion gear 18 teeth (Ratio 1:6.777) Therefore approx roll speeds as follows: Input motor speed 1300rpm: Front roll 21.53 rpm Back (fluted) roll 19.6 rpm

STOCK NUMBER U2064 Description: Used line for compacting powders by ALEXANDERWERK (Germany). Line consist of: - feeding system - includes: 50 l powder container, rotary valves, vacuum pump, piping and bag filter. - horizontal, twin screw, feeder with adjustable working speed in range 0-77 rpm. - granulating system - includes - preparation granulator and two precise granulators, type RFG 150N. All granulators works with adjustable speed in range 0-112 rpm. - intermediate tank with screw type agitator, working with adjustable speed in range 0-20 rpm. - roll compactor ALEXANDERWERK model WP170/120V, designed in stainless steel. Machine has two rolls, each with width 120 mm x diameter 170 mm, mounted vertically. Rolls are working with adjustable speed in range 0-20 rpm. Driven by gearbox and electric motor 7.5 kW. Rolls are pressured via hydraulic device. Maximal pressing power up ...

1 x Adamson 96in wide x 32in dia 4 roll Z Calender line, peripherally drilled rolls with oil heating, motorised nip adjustment to rolls 1,2 and 3 (roll 4 fixed). Cross axis roll 4. Hydraulic pre-load to all rolls, Adjustable stock guides, rubber coated pressure roller with hydraulic adjustment and v/s motor to roll 4, with Adamson unidrive gearbox on universal couplings, with 500HP, 850/1300rpm, 785A, 500V, 3ph, 60Hz Reliance DC variable speed motor to rolls 1, 2 and 3. 200HP, 850/1400rpm DC variable speed motor to roll 4. 1 x Embossing station 1 x set of 8 x 96in wide x 24in dia stainless steel cooling drums. 1 x Dual turret winder. Full drawings available. We can supply the upstream equipment I.e. internal mixers that fed the calenders, along with the batching and material handling/dosage equipment. Complete line available in very good condition previously us ...

1 x Francis Shaw Model K6 Intermix, Original year of manufacture: 1977, Rebuilt body fitted by Carter serial no. 242.93, Year: 1993, Hydraulic drop door discharge, Mixing chamber volume: Approx 112 litres Pneumatic hopper, 750HP, slip ring motor, 3ph, 50 Hz through Sturdigear 1460/15.7 rpm reduction gearbox (1000HP rating). Complete with hydraulic unit + operator controls etc and in very good condition.

Roller die line consisting of:- 1 x Troester 200mm pin barrel extruder Type QSM200K-16D power roller feed, 10 rows of 8 pins, L/D ratio 16:1 Serial no. 1816/88, year 1988, With temperature regulation unit, 282kW ASEA DC variable speed motor mounted on rails (moves away from calender to clean out etc) Hydraulic sheeting head linked directly to:- 1 x Adamson 24in dia x 68in wide two roll calender, peripherally drilled rolls cross axis, bush type bearings, motorised nip adjustment with unidrive gearbox 277kW ASEA DC variable speed motor Hydraulic clamping device for extruder Set of 4 x cooling drums Dual wind up and liner applicator Chalking Unit Siemens PLC control. Complete line in excellent condition. PRICE: On request.

Manufacturer Heckler & Koch Model AM 444 A Power consumption: 5.5 KW Voltage: 380/400 Volts Spindle holders for vertical and horizontal spindles: 40 Slide movement x = 410nn y = 350mm z = 400mm Vertical clamping table 850 x 255 mm Feed range 0-1500 mm/min Sliding gearbox 12-stage Speed: 63-2800 rpm Step jump 1.4 CNC control CNC 783/m Dimensions (HxWxD) 1.800x2.400x1.700mm Weight 1,500 kg Ref.Nr PLW18 Mistakes reserved!

Farrel Pomini model F620 Banbury internal mixer, net mixing chamber volume: 710 litres Machine number 6515. Original year of manufacture: 1972, but body replaced 1998 approx batch weight at SG 1 - 533kg, 4 wing rotors, drilled sides, fully stellite welded chamber, rotors and floating weight, S.S.A. dust seals, hydraulic drop door with linear actuator, pneumatic hopper, unidrive gearbox with 2 x CEM 1475kW, 1550A, 1000V, 800/1000rpm DC variable speed motors, Drive controls included, but operator controls not available. In good condition (only used for tyre compound masterbatch). Spares available: Door top (new), hinge shaft (new), 2 x dust seals, hopper seals and bearing seals.

Cat. no. 08-1535F in very good condition self-supporting complete with tools, electrical control for beer,wine,fruit juice Gearbox horizontal Drum speed: 4800 rpm Swallowing capacity: 20,000 Ltr/h Dimensions and weight: Height: 190 cm Length: 170 cm Width/depth: 140 cm Weight approx. 2 ton For further information call: 09353 90905-0 or fax: 09353 90905-22 Mobile: 0171 651 82 48 All prices are ex works plus VAT, from stock. Intermediate sale reserved. Sightseeing is also possible in the evening or on weekends by appointment.

1 x Farrel model F270 Banbury internal mixer, Machine number: 98M5023, Year 1999, 270 litre capacity, 2 wing rotor design, FYH type dust seals, Hydraulic drop door with linear actuator, Process oil system, Pneumatic hopper. with semi unidrive gearbox, AC variable speed motor, 550V (includes 11kv > 550v transformer). Alstom \Syncdrive\ AC variable speed drive controller, 1265 KVA, 550V, digital drive new in 2001. With Promtec Control system (complete but PLC missing). In feed conveyor and dust extraction system also available if required (at additional cost). Spare motor also available. Complete and in good condition (still installed at a factory in UK).

Thyssen Krupp model GK270NC Banbury type internal mixer, 4 wing tangential rotors, Year of manufacture: 2003 Latest Continental design chamber! Hydraulic hopper + power pack. Body and hopper only in good condition. Unidrive gearbox and motor can be quoted for if required (same centres as 11D or F270).

intake cross section: 1,600 x 1,200 mm motor power: 2 x 45 kW knife width: 55 mm knife number: 56 pieces rotor flight circle: 655 mm Planetary gearbox

OPERATING POSITION... HORIZONTAL PUMP SET SIZE . 90.1 CONSERVATION SILICONE OIL ROTOR . . . . . . . . . . . . . 1.2436 U80 STATOR . . . . . . . . . . . . . NBR-LM 778/60-ST MOUNT RINGS... 1.4571 TENSION ROD MATERIAL... 1.4301 JOINT MATERIAL... . V4A JOINT DESIGN... . CARDAN (PW) ABGEDIC. CUFF... NBR TISSUE JOINT OIL... White oil EXTRA SHAFT SEAL... SPECIAL VERSION SUCTION CASING... V4A SUCTION... DN100/PN16-V2A SUCTION LOCATION TOP GASKET... NBR OUTLET... . DN100/PN16-V2A DRIVE flange [mm]... 250 Drive shaft [mm] 40 SHAFT MATERIAL... V2A LINEUP SPECIAL VERSION PUMP PROTECTION... WITHOUT ROTATION LINKS PUMP IDENTIFICATION... CHEEKS NAMEPLATE... STANDARD SURFACE PROTECTION... STANDARD C1 FARBE . . . . . . . . . . . . . RAL 9006 WEIßALU DRIVE... STIRNRADGETR.MOTOR DRIVE GEARBOX TYPE SEW RF77 ENGINE TYPE... DRE100LC4 PERFORMANCE... 3.0 KW SPEED at 50 Hz [ ...

1 x Repiquet 2550mm wide x 820mm dia 4 roll inverted L Calender, Machine type: CALANDRE 4 CYL DE 820 x 2550, Machine no. 70-C9-87 Motorised nip adjustment, Peripherally drilled rolls, High pressure hot water hearing Bush bearings with flood lubrication, Hydraulic pre-loading to all rolls, Roll bending and unbending on roll 4, Cross axis on roll 3 and 1. Automatic bank sensors/control + camera system Traversing unit for roll buffing or sand blasting. 'Citroen' unidrive gearbox, type: SPECIAL, order no. 50491, Power 140/240 C.V. Speed 1500/2250, Output 46/59 with individual motor to each roll- Roll 1 and 4 - 130HP, Roll 2 and 3 - 240HP, Max calender speed 120m/min. Dual embossing station with approx 25 x embossing rolls (+ 5 x rubber pressure rollers) In very good condition.

1 x Farrel Bridge model 11D Banbury internal mixer, machine number: 90R2022, Year: July 1991, Pneumatic hopper + extension neck, SSA dust seals, 2 wing rotors, Hydraulic drop door with Linear actuator, Wyco semi unidrive gearbox, with 875Kw, 440V AC variable speed motor with Alston syncdrive controls. In good condition.

SEW-motors with gearbox v. 1, 5kW - 15kW.Die engines have been used mint condition and never.Visits by appointment at any time.

NEW Bainite model BMIM95 95 litre intermeshing type mixer Customs Tariff CN Code: 8477.8093 Manufacturer: Bainite Machines Pvt Ltd Net chamber volume: 95 litre Rotor speed: 6 - 60 rpm Rotor type: HP-5 design (intermeshing) Dust seals: SSA (self-sealing arrangement) Motor power: 420kW, 1000rpm AC motor, 3ph, 50Hz, 380/400V Discharge door: Hydraulic drop door with linear actuator and toggle latch. Two (2) J Type thermocouples mounted in door top as standard One (1) Single acting pneumatically operated oil injector Feed Hopper Assembly: Hydraulically operated Floating weight: single ?V? bottom type Gearbox: Full unidrive type with S.F. 2.25 Bedplate: Fabricated steel Ancillaries: Dust stop lubrication (1.5HP x 2), hydraulic pump unit (20HP) Three (3) Zone closed loop temperature control (TCU) Electrical Controls: Schneider make variable frequency drive (VFD) controls with ...

Stock number: L0931-06 Used Cannon type GCI/450 l/MI approximately 450 l working capacity and 638 l total capacity vertical white glass lined reactor. Internal approximately 902 mm diameter x 665 mm diameter straight side. Has clamped dished top and welded dished bottom heads. internal rated full vacuum / 2.76 bar design pressure at -10 /+ 230 C. Carbon steel jacket 85 l capacity rated 5.17 / 4.17 bar design pressure -10/+230 C. Includes 3-blade retreat curve agitator belt driven by 1.5 kW 415 V, 3/50, 1420 rpm motor via highfield gears size 5 gearbox rated 31/3 reduction ratio and mechanical seal.

Type: LKM 3027 Just: 2213857 ZwischengetriebeNr.: 318978 Disco built gearbox Lenze Type: 11711.06.16 No.: 6/7000/2365 N1 = 1500 min-1 N2 = 65-375 min-1 Engine: Loher power: 2,5 kW on mobile carts Condition good Dimensions: LWH = 1300 x 350 x 750 mm Weight: approx. 100 kg

1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.