126,771 used machines on RESALE, but how to find them? Machine Search
max. wheel diameter:150 mm gear width: mm max. module:3,5 min. module:1,25 total power requirement: kW weight of the machine ca.:6,5 t dimensions of the machine ca.:2,35 x 2,10 x 2,35 m Width of teeth:45 mm boring diameter:100 mm surface area:1300 x 300 mm
max. wheel diameter:130 mm gear width:170 mm max. module:3 min. module:0,5 total power requirement:48 kVA weight of the machine ca.:9 t dimensions of the machine ca.:7,64 x 3,14 x 3,25 m For technical data, see PDF-File enclosed
max. wheel diameter:275 mm gear width:55 mm max. module:6,5 min. module:1,5 Face Hobbing-Continious Process Continuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surface C28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, w ...
max. wheel diameter:275 mm gear width:55 mm max. module:6,5 min. module:1,5 Face Hobbing-Continious Process Continuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surface C28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, w ...
max. wheel diameter:50 mm gear width:20 mm max. module:4 mm min. module:0,1 mm total power requirement:12,5 kW weight of the machine ca.:4000 kg dimensions of the machine ca.:2,2 x 2,5 x 2,3 m workpiece length - max.:300 mm
max. wheel diameter: mm gear width: mm weight of the machine ca.:7000 kg dimensions of the machine ca.:9130 x 3895 x 3450 mm max. top circle diameter:80 mm max. length of teeth cutting:170 mm Total length:240 mm taper diameter:32 mm slide travel radial ( X-axis ):100 mm slide travel tangential ( Y-axis ):160 mm axial movement Z-axis:300 mm/min workpiece spindle - bore:45 mm electr. connected load:44 kVA
max. wheel diameter:260 mm gear width:320 mm max. module:5 weight of the machine ca.:21 t dimensions of the machine ca.:8,71 x 5,97 x 3,49 m no. of teeth:1...999 max. helix angle:+45/-45 ° pitch min.:0,1 mm pitch max.:1000 mm X-axis:345 mm y-axis:250 mm Z-axis:320 mm b-axis:360 ° c-axis:360 ° Coolant is not available. It was central and there is only a booster pump without filtering. For loading system there is a 2-axes robot with workpiece conveyor.
max. wheel diameter:280 mm max. module:7 weight of the machine ca.:13 t table turning speeds:100 U/min table diameter:250 mm min. number of teeth:4 hob turning speeds:1500 U/min max. hob diameter:160 cutter length max.:230 mm Machine in good condition. Available 01.08.2024
max. wheel diameter:200 mm gear width:60 mm max. module:7 weight of the machine ca.:15 t table diameter:180 mm table turning speeds:100 U/min hob turning speeds:750 U/min Machine in good condition, without feed, without automation Available 24.08.2024
max. wheel diameter:900 mm max. module:10 weight of the machine ca.:8200 kos. hob dia. - max.:190 mm cutter length max.:320 mm milling spindle speeds (infinitely variable):13-80 U/min workpiece length - max.:750 mm max. workpiece diameter:150 mm Counter holder milling mandrel is missing
max. wheel diameter:200 mm gear width:50 mm max. module:6 table diameter:168,14 mm boring diameter:65,532 mm weight of the machine ca.:11 t table turning speeds:0-1.000 U/min length of stroke min./max.:0-70 mm no. of strokes:180-1.800 Stück This machine can be used to make tandler gears. However, for helical gearing, a helical guide is also required.
max. wheel diameter:210 mm total power requirement:60 kW weight of the machine ca.:8 t dimensions of the machine ca.:2,85 x 2,60 x 1,80 m grinding slide feed:700 mm grinding slide feeds:1-15.000 m/min max. workpiece weight:150 kg centre height:260 mm grinding wheel diameter:240 mm
max. wheel diameter:275 mm gear width: mm max. module: weight of the machine ca.:9,4 t dimensions of the machine ca.:3,7 x 3 x 2,82 m min. number of teeth:5 max. number of teeth:2000 range of tooth size:20 mm max. gear width (internal machining):58 mm X-axis:325 mm y-axis:350 mm Z-axis:475 mm Bevel gear milling machine Gleason Pfauter including Promot Automation
max. module:7 weight of the machine ca.:5 t worm grinding diameter:280-350 mm width of grinding worm:84-104 mm min. number of teeth:6 max. number of teeth:600 max. top circle diameter:360 mm max. workpiece weight:60 kg without filter
max. wheel diameter:80/120 mm max. module:2,5 max. top circle diameter:65 mm :22 mm :140 mm :120 mm slide travel axial ( Z-axis ):320/400 mm Dimensions (L/W/H):3270 x 3240 x 2020 mm weight of the machine ca.:6 t P60 - The compact all-rounder for wheels, shafts and worms The P60 is the smallest machine in the Gleason line of horizontal hobbing machines. The all-rounder not only mills spur gears with all rollable profiles, but is also the optimal solution for machining steering pinions and worms. with automatic loading system, extraction unit, chip conveyor, with balancing device with 2 tailstocks, with Artec process monitoring system, type CTM-BT1.1
max. wheel diameter:300 mm max. module:7 weight of the machine ca.:15 t table turning speeds:100 U/min table diameter:180 mm hob turning speeds:750 U/min max. hob diameter:300 cutter length max.:230 mm Liebherr LC300 with loading automation Machine including counter holder The machine used to work with emulsion
max. wheel diameter:300 mm gear width:100 mm max. module:5 workpiece turning speeds:0 - 1000 1/min work piece - max.:1100 mm workpiece clamping:auto. tension device number of spindle speeds:1000 1/min. spindle bearing diameter:100 mm diameter of spindle flange:120 mm tailstock travel:80 mm weight of the machine ca.:3500 KG dimensions:1200 x 1450 x 2250 mm total power requirement:10 kVA The Gear Tooth Deburring machine WERA, ZEM 300 for deburring of splines gear wheels and shafts, with Pointing Facility.
max. wheel diameter:300 mm gear width:100 mm max. module:5 workpiece turning speeds:0 - 1000 1/min work piece - max.:1100 mm workpiece clamping:auto. tension device number of spindle speeds:1000 1/min. spindle bearing diameter:100 mm diameter of spindle flange:120 mm tailstock travel:80 mm weight of the machine ca.:3500 KG dimensions:1200 x 1450 x 2250 mm total power requirement:10 kVA The Gear Tooth Deburring machine WERA, ZEM 300 for deburring of splines gear wheels and shafts, with Pointing Facility.
max. wheel diameter:5 - 260 mm gear width:400 mm max. module:15 min. module:0,5 gear hobbing diameter - internal:30 mm max. helix angle:> 85 ° Aussenverz. max. helix angle:> 45° Innenverz. Testing Range vertical:400 mm dist. between centers:5 - 600 mm table diameter:260 mm max. table load:100 kg speeds:30 1/min total power requirement:1,6 kVA weight of the machine ca.:900 kg dimensions of the machine ca.:200 x 1300 x 2150 mm CNC Gear Tester in good condition, out of OEM Test Lab. For measuring of spur and helical toothing, additional of rotationally symetric parts as true running, coaxiality, axial runout, etc. with tool changer ( 4 nos.)
max. wheel diameter:300 mm gear width:100 mm max. module:5 workpiece turning speeds:0 - 1000 1/min work piece - max.:1100 mm workpiece clamping:auto. tension device number of spindle speeds:1000 1/min. spindle bearing diameter:100 mm diameter of spindle flange:120 mm tailstock travel:80 mm weight of the machine ca.:3500 KG dimensions:1200 x 1450 x 2250 mm total power requirement:10 kVA The Gear Tooth Deburring machine WERA, ZEM 300 for deburring of splines gear wheels and shafts, with Pointing Facility.
max. wheel diameter:180 mm max. module:5 min. module:1 weight of the machine ca.:14 t dimensions of the machine ca.:4,5 x 2,84 x 2,8 m min. number of teeth:7 toolpiece turning speed range:4000-10000 U/min tool length:210 mm With tail stock No dressing device Only CBN
workpiece diameter:63,5 mm centre distance:350 mm honing length max.: mm total power requirement: kW weight of the machine ca.:6 t dimensions of the machine ca.:2,70x2,30x2,60 m Technical data G0504 working space Length of the clamping surface mm 1550 Number of T-slots mm 2 Width of the T-slots mm 18 Distance between T-slots mm 180 Center height (tailstocks) mm 350 Swivel range of the fine wheel head (U-axis) degrees + 30 / -30 Center distance - tailstock / fine wheel min./max. mm 120/225 Input resolution (all NC axes) mm / degrees 0.001 Delivery slide Movement range (= Z-axis travel) mm 105 Input resolution mm 0.001 tool Outside diameter min./max. mm 225/275 Hole diameter mm 160 Width mm 60 workpiece Outside diameter min./max. mm 40-150 Module min./max. mm 1.25-4.0 Tooth width max. Mm 45 weight Weight of the machine approx. Kg 5500 Operating fluid requirements Cooling lubricant recomme ...
Straightening and cutting machine rolling from Coil. used test line please ask us for your special offer.
Technical data: Machine stand, Type 539 Band saw roll diameter 1400 mm Band saw roll width 180 mm Saw blade width max. 200 mm Saw blade length max. 9300 mm Saw blade thickness 1.3 mm Saw blade speed approx. 42 m/sec. Drive power 45 kW, (1500rpm) Cutting feed requires. 22.5 m/min -Incl. electrical equipment, consisting of limit switches for saw blade voltage, path limitation for transverse movement -2 electromechanical width adjustment devices with precision spindle and two-stage special drive - designed for connecting a Fraba digitizer 2800 -2 hydro-pneumatic band saw roller brakes
Thread cutting power M 2 - M8 Speed: 700 rpm, luf requirement: 750 l/min, pressure 6 - 7 bar, working range extension: 300 - 1900 mm, Afbau parallel arm: stable arm structure made of hard aluminium profile (38x29) Weight: 23 kg, adapter holder: TCS 1 B - incl. 6 safety slip couplings according to your choice year: 2009
Material: Steel Engine: 15 kW Other data and price on inquiry. You can also get the entire system with all components.
Crosscut and miter saws with maximum cutting height of 200 mm stable grey cast iron construction precise ball bushing guide of the tool slide on hardened and ground steel shafts Manual saw feed fast up to 65 ° horizontal MITRE setting and 60 ° vertical for adjustable fixed stops lower blade guard to extractor can be connected Machine mounted on mobile machine base with 1,5 mtr. long rollers left and right left side with scale and stop position slider Technical data: Engine: 400 V / 5.0 kW Speed: 2800 RPM Cutting length: 420 mm (at 90 °) Cutting height: 200 mm (at 90 °) Miter range horizontal: 45°-90° - 20 ° Miter range vertical: 60° - 90°-30° Saw blade diameter: 520 mm Dust nozzle: 100 mm Weight: 490 kg
Thread cutting capacity: M 3 - M 12 Speed: 400 rpm Air demand: 750 l/min Pressure: 6 - 7 bar Extension: 950 mm Standard accessories: Parallel arm Air motor 6 pcs safety slip couplings of your choice guide column with mounting flange Radial boom Maintenance Pneumatic oil for initial filling
automatic CUTTING BORING and MOULDING machine BACCI TTF1 2TM . second hand machine working conditions : Excellent hydraulic drive of all the movements volt. 380/50 CE mark : YES Machine suitable for assembling part of chairs, tables, frames, furniture, wheelchair frames, etc. The BACCI TTF1 2TM performs the operations of cutting , milling and drilling at the end of the piece, either singularly or differently combined . the milling unit is composed of n.02 spindle moulders ( anti-splinter system ) machine composed by 3 working units : 1- Cutting unit : circular saw max.diam. mm.400 motor power Hp 3 2- Boring unit : boring head with 5 mandrins motor power Hp 3 3- Moulding unit . with automatic movement of the carriage on recirculating ball bearings n.02 spindle moulders (anti-splinter) motor power Hp 7,5 spindle diam. mm.35 hydraulic unit motor power Hp 2
Weight 1750 kg Length x Width x Height 1800 mm x 1350 mm x 3000 mm Machine data: rotor diameter - knife circle : 500 mm length rotor : 630 mm angular speed rotor : appr. 650 min-1 after-run duration : appr. 60 sec. motor power - depent of order: 37 kW / 1500 min-1 45 kW / 1500 min-1 idle power :appr. 30 - 40 % of nominal power. Very good condition, ready to work. You can also get the entire system with all components.
Cutting cutter Kjellberg-Eberle - used Type: SII20 Machine No.: 1331 - 220 V, 50 Hz, 2.5 kVA, IP 31 - on 04.02.1990 a new control system (NS 3003) was installed by Etek - Built in 1974 - 4 burners - Table dimensions: 6m x 2.50m - Total area: 6m x 5.5m x 2.4m In good condition!
Working width: 820 mm rotor flight circle: Ø 720 mm drive: 90 kW cutting system: 8 cutting blades equipment: mechanical adjustment of the cutting gap Machine weight: 3500 kg
AUTOMATIC CUTTING , BORING and MOULDING machine type PADE 1000 N Machine suitable for assembling part of chairs, tables, frames, small furniture, wheelchair frames, etc. The PADE 1000 N performs the operations of Cutting , milling and drilling at the end of the piece, either singularly or differently combined. All movements of the machine are controlled by pneumatic devices. composed by 3 working units : 1- Cutting unit circular saw diam. mm.350 motor power hp 3 2- Boring unit boring head with 5 / 7 mandrins motor power Hp 3 max. working stroke of boring unit mm. 130 3- Moulding unit vertical spindle for moulder motor power Hp 5,5 spindle diam. mm.30 pneumatic sliding carriage volt. 380/50
very well preserved, fully reconditioned MAZAK laser machines with 1500W Table format: 2500 x 1250 mm minimal footprint by 2, 6 m x 6, 5 m Small part conveyor completely encapsulated engine cover FE: up to 12mm VA: up to 6mm Plastic can incl. software including warranty incl. extraction incl. commissioning + training
Tip height: 330 mm centre distance: 1500 mm circular diameter: bed 690 mm spindle bore: 82 mm spindle retainer: short taper size 8 taper tailstock: 6 MK spindle speed: 7.1-1400 rpm feeds: longitudinal/plan 0.05 112/0.025 56 mm / U thread pitches: 0.25-560 mm electrical connection: 380 V, 15 kW space: 3350 x 1800 x 1400 mm weight: 4800 kg
Die Cutting Machine Unitec T1060 Die Cutting Machine Unitec T1060 The T1060 automatic machine with or whithout stripping is used to diecutting and creasing paper, cardboard and corrugated and operations for cardboard boxes, paper labels and especially for delicate printing jobs such as cigarette packages, wine, gifts and cosmetics, etc. This machine works automatically throughout its process, with a user-friendly interface to control the cutting speed, number of sheets cut, total operating hours and its working status, as well as to dynamically control the PLC inputs and outputs, and malfunctions to facilitate operation control and troubleshooting. In addition, the machine also features self-testing (e.g., double sheets, missing sheets, accumulated sheets, or fallen sheet detection) and continuous process sampling, while providing you with a solid cutting and accuracy registr ...
New machine 24-month warranty Benefits: + TOP value for money + Horizontal cutting machine, ideal for hamburger buns / rolls & cake bottoms + also suitable for cutting /halving baguettes, flatbreads, white breads + Products are guided with conveyor belt to the cutting station + comes with 3 cutting knives, double and triple cutting possible + Adjust cutting height in 5 mm increments + Machine on a robust, mobile frame, with locking wheels + equipped with two safety protective grilles + with upper transport/feeding belt + Tape speed can be controlled by rotary knob, for optimal adjustment of cutting results + with cleaning brushes on the conveyor belt + with quick coupling for belt cleaning + with pull-out collecting plate on the output belt + fast spare parts supply within 1-2 business days Technical data: - max product height: 90 mm - Bandwidth: 405 mm - Band spe ...
Tip height: about quilt 300 mm centre distance: 1500 mm circular diameter: upper bed 640 mm spindle bore: 67 mm spindle retainer: Gr. 8 taper tailstock: 5 MK spindle speed: 18 - 900 rpm feeds: longitudinal/plan 0.063 0.032 2.1 mm / U thread pitches: 0.5-14 mm electrical connection: 380 V, approx. 7.5 kW space: 1550 x 3100 x 1250 mm weight: approx. 3500 kg hardly used and therefore well-preserved bed lathe
Bread cutting machine Rösen & Robbert SPA 38 used sickle knife bread cutting machine with adjustable cutting width for breads up to 38cm long suitable for cutting and halving dark breads.Used bread cutting machine with cutting width adjustment of Rösen & Robbert type SPA 38.The machine runs with oiling, with sickle knife and digital steurung.Geignet to cut breads up to 38cm wide.Right compartment is inserted bread then the bread is inserted to the left. In the middle between left and right compartment, the knife rotates and cuts the bread in the desired thickness. The slices are pushed into the left compartment where they are just selected mid-disc holders. After cutting, mam can take out the slices and bag it on the tray. Easy operation and cleaning of the machine, little space requirement.Payment and shipping on request. Bread cutting machine R&R Type: SPA 38 for loaves up ...
Working width: 2000 mm rotor flight circle: Ø 1000 mm drive: up to 315 kW cutting system: 40 piece cutting bars facilities: counter knife traverse pivoting hydraulically Right-left operation Hydraulic hood opening Screen: hydraulically extendible
Waterjet 2x3m demonstration plant about 50 hours with comfortable visualized CNC control, and comfortable CAD connection. Cutting table made of stainless steel. The plant is connection, etc. in mint, latest cutting software, AutoCAD Used pumps either Knam/H2O 40HP alternative KMT/Ingersollrand SL4 30hp completely overhauled. New surcharge KMT SL5 classic 50PS/37KW 90.000,00 Construction training & service directly from the manufacturer, including
VESPA 30/60/18.5 VGA Cutting mill for plastics 18.5 KW, 200-300 kg/h. Insertion opening mm: 620×400 Rotor diameter mm: 300 Throughput kg/h: 200-300 Rotor blade quantity/mm: 6 x 300 Stator knife quantity/mm: 4 x 300 Engine KW: 18,5 Dimensions mm: 1210×1000×1925 Weight kg: 1500 options: Material conveying blower 4.0 kW and Big Bag filling station. Soundproofing can also be ordered at an additional cost. VESPA Granulators for Plastics – Soundproof insertion opening for minimal noise level and easy feeding with multiple alternative feed options – Horizontally or diagonally separated housing with robust welded steel construction – The cutting rotor rotates in an extremely robust self-aligning roller bearing, which is arranged in the bearing housing outside the cutting chamber. – Easy access to the knives. Knife made of high-quality tool steel with pre ...
VESPA 45/80/37 kWt VGA Cutting mill for plastics 37 KW, 400-700 kg. Model VESPA 45/80/37 kWt VGA Throughput Kg/h: 400-700 Rotor diameter мм: 450 Rotor knife quantity/dimensions piece x mm: 6×400 Stator Knife Quantity/Dimensions Piece x mm: 4×400 Engine kW: 37 Weight Kg: 2300 VESPA Granulators for Plastics – Soundproof insertion opening for minimal noise level and easy feeding with multiple alternative feed options – Horizontally or diagonally separated housing with robust welded steel construction – The cutting rotor rotates in an extremely robust self-aligning roller bearing, which is arranged in the bearing housing outside the cutting chamber. – Easy access to the knives. Knife made of high-quality tool steel with precision machining and surface finish – Good accessibility for cleaning and maintenance – Electrical equipment with SCHNEIDER ELEC ...
Waterjet 1x2m demonstration plant about 50 hours with comfortable visualized CNC control, and comfortable CAD connection. Cutting table made of stainless steel. The plant is connection, etc. in mint, latest cutting software, AutoCAD Knam/H2O pump 22 HP. 65.000,00 Construction training & service directly from the manufacturer, including
Cutting mill for high demands in a compact class. The mill is ideal for grinding small quantities. In production, there are always surpluses, missing parts. These recyclable materials can flow back into production, so that manufacturing costs can be optimized and reduced. Cutting mill VESPA 18/32/5.5 kW VGA for plastics, cable 5.5 KW, 60-80 kg/h. Model: VESPA18/32/5.5 kW VGA Throughput Kg/h: 60-80 Rotor diameter мм: 180 Rotor knife quantity/dimensions piece x mm: 6×160 Stator Knife Quantity/Dimensions Piece x mm: 4×160 Motor kW: 5.5 Weight Kg: 400 options: With material conveying blower and Big Bag filling station Information on throughput quantities is indicative and depends on the type of material, shape, temperature, feed method, rotor configuration, blade sharpness, sieve size, etc. Dimensions (mm) A 860 B-620 C-1480 D 1250 E 325 F 220
Cutting mill for high demands in a compact class. The mill is ideal for grinding small quantities. In production, there are always surpluses, missing parts. These recyclable materials can flow back into production, so that manufacturing costs can be optimized and reduced. 40/80/30 VGA granulator for plastics 30 KW, 350-600 kg/h. Model: VESPA 40/80/30 kWt VGA Throughput Kg/h: 350-600 Rotor diameter мм: 400 Rotor knife quantity/dimensions piece x mm: 6×400 Stator knife quantity/dimensions piece x mm: 4×400 Motor kW: 30 Weight Kg: 1960 options: With material conveying blower and Big Bag filling station Information on throughput quantities is indicative and depends on the type of material, shape, temperature, feed method, rotor configuration, blade sharpness, sieve size, etc. Dimensions (mm) A 1520 B-1430 C-2420 D 1910 E 820 F 500
VESPA 40/60/30 VGA Granulator for plastics 30 KW, 300-500 kg/h. Insertion opening mm: 620×500 Rotor diameter mm: 400 Throughput kg/h: 300-500 Rotor blade quantity/mm: 6 x 300 Stator knife quantity/mm: 4 x 300 Motor KW: 30,0 Dimensions mm: 1540x1190x2280 Weight kg: 1760 options: Material conveying blower 4.0 | 5.5 | 7.5 | 11 kW and Big Bag filling station. Soundproofing can also be ordered at an additional cost. Information on throughput quantities is indicative and depends on the type of material, shape, temperature, feed method, rotor configuration, blade sharpness, sieve size, etc.
VESPA 35/50/15 VGA Cutting mill for plastics 15 KW, 150-250 kg/h. Insertion opening mm: 520×380 Rotor diameter mm: 350 Throughput kg/h: 150-250 Rotor blade quantity/mm: 6 x 250 Stator knife quantity/mm: 4 x 250 Motor KW: 15,0 Dimensions mm: 1180x880x1970 Weight kg: 1150 options: With material conveying blower 4.0 kW and big bag filling station. Soundproofing can also be ordered at an additional cost. Information on throughput quantities is indicative and depends on the type of material, shape, temperature, feed method, rotor configuration, blade sharpness, sieve size, etc. VESPA Granulators for Plastics – Soundproof insertion opening for minimal noise level and easy feeding with multiple alternative feed options – Horizontally or diagonally separated housing with robust welded steel construction – The cutting rotor rotates in an extremely robust self ...
maximum number of results exceeded
please refine your search
