ge mi fu used for sale

Qty. 1 Second-hand skin pass mill Mfc.: Mannesmann Demag Sack Built: 1980’s Modernised in 1986 & 1993 Type: Duo Cold Rolling Mill – Non-Rev. Dia. 330 x 500 mm Material: Carbon steel, cold rolled and annealed Strip width: 80 - 470 mm Thickness entry: 4.0 mm Exit: 0.2 mm Decoiler Modernised in 1986 ID: 400 with segments 500 & 600 mm Spreading range: 370 – 420 mm Strip tension: 1300 – 65 daN Braking system: Generator Braking torque: max. 1300 daNm De-coiling speed: 2.5 m/sec. Coil cross section: 20 – 1880 mm² Coil weight per mm strip width max.: 10 kg Coil weight: 5.0 T Coil ID: 400 & 500 mm Coil OD: 600 – 1400 mm Roll dia.: 300 – 330 mm Roll length: 500 mm Roll force: 1850 – 2400 kN Min. roll force: 150 kN Hydraulic roll adjustment Adjustment stroke: 80 mm Adjustment speed: 1 – 3 mm/sec. Rolling speed: 2.5 m/sec. (150 m/min.) PLC system: ...

New machine Capacity: 8,000 litres water filling Volume: approx. 7,000 litres Bulk density: max. 0, 6 kg / litre Maximum filling: 4200 kg •Bowl, cover, swivel arm, mixing screw, spout housing made of V2A Traverse from mild steel, is covered but to the tank interior with a V2A plate. -All lubricants are H1 & halal approved and certified ATEX Zone 21 Consideration and introduction of the ATEX zoning 21 within the mixer. -Infrarot sensor Temperature monitoring tips storage with PT 100 Dampers manhole Explosion protection document Monitoring unit with temperature display

Lot 592 500L steam jacketed hemispherical scrape surface vessel, bottom central discharge, half moon lid, agitator (six sets of removable propellers along shaft)

Reed 42" x 16" Two Roll Mill. 40HP Motor, with clutch brake. Friction ratio 1.1 Manual Nips. On one-piece steel bedplate.

1 piece NAUTA mixer MBX 28-R -Volume ca. 2.300 litres - bulk density CA. 0, 9 kg / l -Gearbox reconditioned vintage cameras -Swing-arm reconditioned vintage cameras -Container made of stainless steel V2A new products -Mixing screw stainless steel V2A new products -Spout pneumatically driven new product -Drive motors 5, 5kW & 0.37 of kW Virgin

1 piece NAUTA mixer MBX 40-R -Volume approx. 3.200 litre - bulk density CA. 0, 7 kg / l -Gearbox reconditioned vintage cameras -Swing arm mild steel Virgin -Container made of stainless steel V2A new products -Mixing screw stainless steel V2A new products -Spout pneumatically driven new product -Drive motors 5, 5kW & 0.55 of kW Virgin

1 piece NAUTA mixer MBX 50-R -Volume approx. 4.000 litre - bulk density CA. 0, 6 kg / l -Gearbox reconditioned vintage cameras -Swing arm mild steel Virgin -Container made of stainless steel V2A new products -Mixing screw stainless steel V2A new products -Spout pneumatically driven new product -Drive motors 5, 5kW & 0.55 of kW Virgin

3 liter laboratory mixer -Container V2A -Container to remove -Drive 1 motor frequency controlled

Qty. 1 Second-hand foil rolling mill plant Mfc.: World Co. (Japan) Type: 6-Hi – Non reversing mill Built: 2002 Application: Copper foil Width: 400 – 700 mm Coil weight: Max. 5 Ton Thickness Entry: 100 – 200 microns Exit: 5 – 100 microns Speed: 0-400/800 m/min. Thickness X-Ray unit AGC system Variable Crown Control Hydraulic servo equipment Main motor power: 200 kW DC Slitter line Mfc.: IHI Width: 150-700 mm Thickness 5 – 50 microns Degreasing line Mfc.: World Co. Strip width: 700 mm Thickness: 10-50 µm Treatment line Mfc.: Kawasaki Built: 2005 Width: 700 mm Thickness: 10-50 µm

Qty. 1 Second-hand aluminium foil rolling mill plant Mfc.: Robertson, Kampf, Schmutz, Nishimura, Waldrich-Siegen, Otto-Junker Built: 1962 – 1989 Foil width: 850 mm Entry thickness: 0.4 mm Exit: 2 x 7 microns Scope of supply: Roughing Foil rolling mill: 4-Hi Intermediate foil mill 4-Hi Finishing foil mill 4-Hi Slitters – Qty. 4 Roll grinders – Qty. 2 Annealing furnaces – Qty. 4 Charging car INDIVIDUAL ITEMS CAN BE SOLD

SUMAB Smallest Automatic concrete plant SUMAB MINI The SUMAB MINI is a perfect match for you whether you produce concrete for your own project or need material to produce concrete elements. Technical details: • Easy to put it inside the building and build your concrete element factory. • Designed on a container frame. • 2 aggregate storages, • pan-mixer 500/300 liters. • Water tank 200 liters. • Automatic control of a plant: computer (20 concrete recipes). Concrete plants made by SUMAB are the definition of quality, durability and reliability. Our batching plant are made using Scandinavian technology and components from leading European manufacturers! We offer Scandinavian quality at the best price! If you need more information, you can visit our website, or send a request and we’ll help find the best solution for you!

Mikron C Axis Machine Table - with Heidenhain control 430 - Siemens server motor - Table: 60 x 110 cm - 4th axis, diameter: 50 cm - Weight: 650 kg Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.

Qty 1 x Shaw 60in x 22in two roll mill, Manual nip adjustment, Peripherally drilled rolls (front and back), Hinged guide plates, Sleeve bearings with motorised lubrication, Right angle drive gearbox with 115Kw DC variable speed motor, All mounted on a heavy duty bedplate. Carter stockblender mounted on too. Complete with controls etc and in very good condition.

Mixer for gentle mixing of temperature-sensitive masses with resins, waxes, etc., incl. control cabinet and AZO weighing scale (1,500 l., on 3 measuring cans), without mixing container. Product-contacted parts made of stainless steel.

1 x Heavy duty 2 roll mill Roll dimensions: 2100mm x 665mm dia. Hydraulic nip adjustment, Safety push bars, Peripherally drilled rolls, Sleeve bearings with grease lubrication, Right angle drive gearbox, with Siemens 240kW DC variable speed motor, Strip knives fitted to front roll, Heavy duty fabricated bedplate, Carter stockblender mounted on top.

Stock# U2415-1 Used stainless steel conical mixer by Hosokawa Milacron model DBXE-300R. Total volume 798 l, working volume 300 l. Mixer has top mounted stainless steel unsupported mixing screw, driven via gearbox and el. motor 2.2 kW. Rotating arm is designed in carbon steel and is driven via gearbox and el motor 0.18 kW. Bottom central discharge via outlet with diameter 200 mm and manually operated slide valve. Machine is mounted on three carbon steel legs and is equipped with local control panel. Last time machine had been working in food industry. Shipping dimensions: diameter 1400 mm x length 3200 mm x weight 800 kg.

Qty. 1 Second-hand aluminium foil rolling mill line Mfc.: Kyongil Machinery Built: 2003 Stopped: 2015 Type: 4-Hi Strip width: 850 mm Thickness Entry: 0.3 mm Exit: 12 microns Consist of: Foil rolling mill Foil separator Doubler Annealing furnace

Ideal for passage driving with consistent efficiency and for achieving the narrowest grain size distributions in the micrometer range, Maximum operational safety: even the basic version is designed in accordance with the explosion protection directive for installation in ATEX Zone 1 (ExII 2 G cb IIB T3) Grinding media sizes from 0.5–2.5 mm diameter Ideal cooling properties: The forced routing of the cooling water in the outer jacket allows the processing of temperature-sensitive productsEasy handling – each DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Easy handling – any DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Grinding tank: 5L Power : 12,5kW Voltage : 380V Weight : 450kg

Ideal for passage driving with consistent efficiency and for achieving the narrowest grain size distributions in the micrometer range, Maximum operational safety: even the basic version is designed in accordance with the explosion protection directive for installation in ATEX Zone 1 (ExII 2 G cb IIB T3) Grinding media sizes from 0.5–2.5 mm diameter Ideal cooling properties: The forced routing of the cooling water in the outer jacket allows the processing of temperature-sensitive productsEasy handling – each DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Easy handling – any DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Grinding tank : 50 litres Power : 45 kW Voltage : 380 V Weight : 1050kg

Holy V-mix, Nautamix, Vrieco-, NAUTA mixer, cone mixing N.M. Holy b.v. V-mix 25,000 PLR New machine of the mixer is on your products (E.g., particle size, bulk density) and environment (E.g. ATEX zoning) adapted. -Capacity: 25,000 litres water filling -Usable volume: approx. 22,500 litres depending on the product properties -Container, lid, swing arm, mixing screw, spout housing made of V2A -Traverse normal steel, is covered but to the tank interior with a V2A plate. -All lubricants are H1 & halal approved and certified

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Manual nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 106kW DC variable speed motor. Very good condition.

Qty. 1 Second-hand aluminium foil rolling mill plant Mfc.: Sambhav Built: 1993 - 2012 Revamped: 2015 Foil width: 1000 mm Entry thickness: 8 mm Exit: 8 microns Consist of: Melting furnace 22 MT Holding furnace 15 MT Strip caster Roughing rolling mill Intermediate foil mill Finishing foil mill Heavy slitter Strip slitter Foil separator Qty. 2 Foil slitters Annealing furnace

Qty 1 x Schwabenthan 200mm dia x 450mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Jahnel gearbox with 10HP motor to each roll (variable speed), Variable friction ratio/roll speeds, Stainless steel interlocked guards and tray. Complete with electrical controls and in good condition. O/a dimensions 2700 x 1500mm

Qty 1 x Schwabenthan 150mm dia x 350mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Even/friction selectable gear ratios, Motor mounted under frame. Complete with electrical controls and in good condition. O/a dimensions 2400 x 850mm.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible coupling, 2 x 68kW DC variable speed motors. Variable friction ratio/roll speeds. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 138kW fixed speed motor. Fixed friction/roll speed. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible couplings, 2 x DC variable speed motors. Variable friction ratio and roll speed. In very good condition.

Year of constr.: 2019 Dimensions: L 4400 mm x W 3500 mm x H 5000 m Ploughshare mixers: Type: PPP 2000 / 3 Manufacturer: MINOX Volume: 2000 Lt. Material: Stainless steel 3 x cutter heads Main drive: 37 KW;

MITSUBISHI MARINE PROPULSION ENGINE 735 kW 1450 RPM 2000 hours

we have all spare parts for the above engines Mitsubishi S6A3 , S12A2 S6R2 S12R S16R new and used Spare parts Cummins KTA all models,

Newmix Atmi life sciences Double jacketed paddle mixer Serial: 15883-005 2011, Stainless pharmaceutical mixer with 500L double jacketed mobile holding vessel, touch screen controls, Min - Max temp 0-90' degrees, jacket volume 6L, 1Ph

Milling machine 4-axis (15995740874) DMG Milltap 700 (2015) Spindle 24,000 1/min NC parts apparatus Lehmann EA-510. L Tool magazine 25 places Renishaw Measurement Kit Rinsing gun Milling machine 5-axis (15995747284) DMG Milltap 700 (2015) Spindle 24,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Rinsing gun Renishaw Measurement Kit Milling machine 5-axis (15995765944) DMG Milltap 700 (2018) Spindle 10,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Renishaw Measurement Kit Automatic front door Automation interface including automation door on the right Milling machine 5-axis (15995734744) + WH3 (770200062R) DMG Milltap 700 (2014) Spindle 10,000 1/min Swivel rotary  ...

Various millstones

PVS 150 V Multicut with 15 to 22 KW with combinable cutting systems Rotor/ stator non-contact Hole disc with knife head or rotor/stator with perforated disc system 2 cutting stages

Two Roll Mill 1m wide Hydraulic Nips With motor and gearbox AEG motor, 380volts, 107amps, 55kw, 1475rpm, 50 cycles Unidrive Gearbox manuf: Santasalo, Type 3KSV70, Year 1977, Weight 1500kg Lunn Safety gear fitted front and back of Mill Complete with control panel All mounted on a one piece bedplate Compact

Height 1950 Width 1300 mm Length 3000 mm Voltage Electrical: 400V 50Hz 3N Installed Power 45 kw Main material Stainlees Steel Throat Diameter 180 mm Feeding System Hooper Throat Material Stainless Steel

Material : Stainless steel Drive: 30 KW Volume: 1200 ltr. - incl. control cabinet; --> Mixer with drive mounted on base frame.

Material : Stainless steel Dimensions: L 4.40 m x W 3.50 m x H 5.00 m --> Complete mixing tower in stainless steel version: --> with plough charmer : Manufacturer: MINOX Type: PSM 2000 / 3 MK Volume: 2000 ltr. Material : Stainless steel 3 x knife heads Main drive: 37 KW.

Mikron Milling Machine WF2/35 - Width: 120 cm - Depth: 140 cm - Height: 180 cm Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.

REALMECA MINI C3X-CNC VERTICAL 1 phase machining milling machine Used for teaching begginers. Perfect condition

Bulk material system for mixing loose flours, powder, ganulate, spices and weighing into smaller batches Manufacturer Daxner GmbH Year of construction 2008 / plant in top condition / in stainless steel The system consists of the following components: 2x Nozzle Filter DFK-14/25/150 2x separation container Dm 1990 mm with vibration floor drain to rotary valve 2x rotary valve type Westinghouse AL 300 3C 2x eddy current screening machine type WM20 with magnetic box for metal separation and 2 sets of screen baskets 4x Horizontal Counterflow Mixer HGM-2000 2x Mixer inlet with folding box 2x Tube screw conveyor RSHN-250 2 x Tubular Auger RSHN-300 2 x Stafsjö Gate Valve (knife gate valve) 4x Transport Dosing Screw, Company Schenck Process GmbH, Type GRMD 42.089.089.0380.44.421.1119 If you want more information, please send us an email to: infobarsso and we will send you all  ...

x-travel 600 mm y-travel 500 mm z-travel 450 mm Control TNC 415 Heidenhain Main spindle: Speed range - milling 20 - 5,000 rpm Drive power - milling spindle 6 / 9 kW Tool holder SK 40 Quill stroke 90 mm Gear stages 4 swivel +/-90 ° Workbench: Bsi0Cso09Qu Table size 900 x 530 mm T-slots 7 T-slots - spacing 63 mm T-slots - width 14-H7 mm max. table load 400 kg Tool Changer: Number of tool positions 18 pos. Tool holder SK 40 max. tool diameter 85 mm max. tool diameter. with a free neighboring box. 150 mm max. tool length 300 mm max. tool weight 10 kg Tool change time max. 15 sec Feeds: Feed rate - fine adjustment 2 ~ 4000 mm/min Rapid traverse X-axis 6,000 mm/min Rapid traverse Y-axis 6,000 mm/min Rapid traverse Z-axis 5,000 mm/min Total power requirement 15 kW Machine weight approx. 3.6 t Dimensions approx. 3.4 x 3.6 x 2.2 m Tool Milling Machine - Universa ...

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

Planetary stirrer stirrer Model: PL 10 mature technology ... already proven many times! Easy manual operation 3 gear gears 1 stainless steel boiler 10 litres 1 flat stirrer 1 kneading hook 1 bhisend Boiler protective grille / intervention protection Table machine with boiler stroke Connection 220V, 550 watts DGUV V3-tested TOP quality and price in one machine! NEW Machine Visit us at the Milbrandt Outlet with show backroom and a wide selection of machines and equipment!

Planetary stirrer stirrer Model: PL 20 mature technology ... already proven many times! Easy manual operation 3 gear gears 1 stainless steel boiler 20 litres 1 flat stirrer 1 kneading hook 1 bhisend Boiler protective grille / intervention protection Table machine with boiler stroke Connection 220V, 1100 Watts DGUV V3-tested TOP quality and price in one machine! NEW Machine Visit our Milbrandt Outlet with show backroom and many machines and equipment!

Planetary stirrer Model: V-Mixer 60 L Professional machine with robust technology! for best results! LED display 10 power levels and timer Intervention protection / safety grille with protective switch thanks to the easy-Trop, continuous work can be done suitable for use in bakery and confectionery Stirring machine with tool: 1 whisk, 1 mixed band, 1 flat stirrer 1 60 litres stainless steel boiler Boiler stroke electric DGUV V3 tested Connection 400V, 4 kW, 16A-CEE plug Dimensions: 742 x 1060 x 1695 mm, WxDxH Continue TOP bakery machines in stock!

Planetary stirrer Model: V-Mixer 80 L Professional machine with robust technology! for best results! LED display 10 power levels and timer Intervention protection / safety grille with protective circuit Stirring machine with tool: 1 whisk, 1 kneading hook, 1 flat stirrer 1 80 litres stainless steel boiler Boiler stroke electric DGUV V3 tested Connection 400V, 4 kW, 16A-CEE plug Dimensions: 853 x 1102 x 1804 mm, WxDxH More TOP bakery machines in stock!

Planetary stirrer Model: V-Mixer 100 L Professional machine with robust technology! for best results! LED display 10 power levels and timer Intervention protection / safety grille with protective circuit Stirring machine with tool: 1 whisk, 1 kneading hook, 1 flat stirrer 1 100 litres stainless steel boiler Boiler stroke electric DGUV V3 tested Connection 400V, 4 kW, 16A-CEE plug Dimensions: 853 x 1102 x 1804 mm, WxDxH More TOP bakery machines in stock!

Planetary stirrer Model: V-Mixer 120 L Professional machine with robust technology! for best results! LED display 10 power levels and timer Intervention protection / safety grille with protective circuit Stirring machine with tool: 1 whisk, 1 kneading hook, 1 flat stirrer 1 120 litres stainless steel boiler Boiler stroke electric DGUV V3 tested Connection 400V, 6 kW, 16A-CEE plug Dimensions: 853 x 1102 x 1958 mm, WxDxH More TOP bakery machines in stock!

Mixer meat 70 liter, NEW Capacity: 35kg Dimensions: 78x61x74cm Power: 2.2kW