ge mi fu used for sale

PFAUTER PE 150 Hobbing machine GENERAL Project No.: 906008 Quantity: 1 pcs. Manufacturer: PFAUTER Type: PE 150 Control: Siemens 840 D powerline Year of manufacture: 1991/2009 Condition: Used machine Engine Approx (hrs): 33500 DESCRIPTION GEAR CUTTING Max. head circle diameter 150 mm Carriage stroke Z'-axis 200 mm Travel in X 150 mm Module 1-3 mm Bevel angle +30 to/to -45 degrees Max. tooth width 150 mm Max. diameter hob 130 mm Max. length of hob 220 mm Tailstock OTHER EQUIPMENT Splash protection cladding with fully encapsulated working area Lighting in the work area Electrostatic oil/emulsion mist extraction system Chip conveyor Engine is/was operated with oil Coolant Setup Circumferential Parts Storage Belt GENERAL TECHNICAL DATA Mains fuse 100 A Total power requirement 49 kVA Machine dimensions (LxWxH) approx. 5820x4047x2810 m ...

Used Aseptic Filling Line SIPA GEA for Milk up to 48,000 bph GEA ASEPTIC BLOW FILL SYSTEM ABF 2.0 Fully aseptic blowing, filling and capping system featuring H2O2-based preforms sterilization. Introduction to the Aseptic Filling Line SIPA GEA for Milk up to 48,000 bhp The used aseptic filling line SIPA GEA for milk up to 48,000 bottles per hour delivers a highly efficient and technologically advanced solution for the packaging industry. Specifically, this system ensures high-quality standards and food safety by using machines from 2018. Moreover, it processes milk in 235 ml bottles with plastic screw caps and a 38 mm neck. The line has only 900 operating hours. SIPA SFR 24 EVO Blow Molding Machine of SIPA and GEA aseptic line The SIPA SFR 24 EVO blow molding machine, manufactured by GEA in 2018, produces high-quality bottles from PET preforms. As a result, it maintains continuous and uni ...

The analyzer measures the deviations and displays them via a recorder. The EVTM device is used to measure gear parameters such as profile, flank line or pitch deviation. • It is mechanically applied to the gear wheel, and deviations are registered via electric displacement transducers (buttons). • The measurement results can then be evaluated or recorded via the first device (the recorder/analyzer). The EVRM is used in conjunction with the other two devices to process vibrations (acceleration/speed/displacement) and output them as an analog signal. It is used for: • Vibration diagnosis on machines (bearings, imbalance, alignment) • Resonance measurements for workpieces / test benches • As an interface between sensor (accelerometer) and meter/recorder/oscilloscope It is sold unchecked from a company closure Auction-ID: A7-46327-1

The analyzer measures the deviations and displays them via a recorder. The EVTM device is used to measure gear parameters such as profile, flank line or pitch deviation. • It is mechanically applied to the gear wheel, and deviations are registered via electric displacement transducers (buttons). • The measurement results can then be evaluated or recorded via the first device (the recorder/analyzer). The EVRM is used in conjunction with the other two devices to process vibrations (acceleration/speed/displacement) and output them as an analog signal. It is used for: • Vibration diagnosis on machines (bearings, imbalance, alignment) • Resonance measurements for workpieces / test benches • As an interface between sensor (accelerometer) and meter/recorder/oscilloscope It is sold unchecked from a company closure

Type: HM 200, high-performance mixer, partly in VA, Y:00, 1987, 6.5 / 9.5kW, 2 knife heads, control cabinet, completely on base frame, drives can be polum-switched.

Rolling milling machine Koepfer 153 A/CNC Manufacturer Jos. Koepfer & Söhne GmbH Type 153 A/CNC Built in 1988 Machine No. 153199 Technical data Largest Module 2 Distance workpiece tool axis max. 4- 87 mm max. workpiece diameter - without magazine 142 mm - with magazine 80 (100) mm max. milling length 150 mm max. length workpiece - without magazine 300 mm - with magazine 220 mm min. number of teeth 3 min. screw gait number 1 Main spindle through- 33 mm Hole Mounting hole for 50 mm Jig max. cutter diameter 70 mm max. cutter width - Universal milling head 63 mm - Shifting milling head 71 mm max. axial cutter shift - Universal milling head 40 mm - Shifting milling head 44 mm 35 Longitudinal feeds 0.1 -5.0 mm /WU 10 cutter speeds 210-1680 /min Control (2 axes) CNC Drive power 2.2 kW Weight approx. 2400 kg Available immediately Location  ...

manual roll gap adjustment 2x7.5 kW motor Bearing Oil circulation lubrication adjustable roller speed 10-41 rpm BJ 1990

Stainless steel container with manhole 500 litres capacity Derivative: NW 50 Dimensions in cm: 120 height x 93 length x 74 width

Operating voltage: 380/400 volts with digital positioning display x,y, without feed in y direction, with angular table, work surface with 4 T-slots Mistakes reserved!

Farrel Pomini model F620 Banbury internal mixer, net mixing chamber volume: 710 litres Machine number 6515. Original year of manufacture: 1972, but body replaced 1998 approx batch weight at SG 1 - 533kg, 4 wing rotors, drilled sides, fully stellite welded chamber, rotors and floating weight, S.S.A. dust seals, hydraulic drop door with linear actuator, pneumatic hopper, unidrive gearbox with 2 x CEM 1475kW, 1550A, 1000V, 800/1000rpm DC variable speed motors, Drive controls included, but operator controls not available. In good condition (only used for tyre compound masterbatch). Spares available: Door top (new), hinge shaft (new), 2 x dust seals, hopper seals and bearing seals.

Manufacturer Heckler & Koch Model AM 444 A Power consumption: 5.5 KW Voltage: 380/400 Volts Spindle holders for vertical and horizontal spindles: 40 Slide movement x = 410nn y = 350mm z = 400mm Vertical clamping table 850 x 255 mm Feed range 0-1500 mm/min Sliding gearbox 12-stage Speed: 63-2800 rpm Step jump 1.4 CNC control CNC 783/m Dimensions (HxWxD) 1.800x2.400x1.700mm Weight 1,500 kg Ref.Nr PLW18 Mistakes reserved!

1 x Farrel model F270 Banbury internal mixer, Machine number: 98M5023, Year 1999, 270 litre capacity, 2 wing rotor design, FYH type dust seals, Hydraulic drop door with linear actuator, Process oil system, Pneumatic hopper. with semi unidrive gearbox, AC variable speed motor, 550V (includes 11kv > 550v transformer). Alstom \Syncdrive\ AC variable speed drive controller, 1265 KVA, 550V, digital drive new in 2001. With Promtec Control system (complete but PLC missing). In feed conveyor and dust extraction system also available if required (at additional cost). Spare motor also available. Complete and in good condition (still installed at a factory in UK).

1 x Farrel model F270 Banbury internal mixer, Machine number: 98M5007, Year July 1998, 270 litre capacity, 2 wing rotor design, FYH type dust seals, Hydraulic drop door with linear actuator, Process oil system, Pneumatic hopper. with David Brown unidrive gearbox, serial no GS50277, Leroy Somer Type LSM54 L76P 1492kW AC motor, Dec 2001, RPM 1000/1200, 750V (includes 11kv > 750v transformer). Output rpm 49.8/43. Alstom \Syncdrive\ AC variable speed drive controller, 1940 KVA, 750V, digital drive new in 2001. With Siemens S5 Control system. In feed conveyor and dust extraction system also for sale if required. Spare refurbished Leroy Somer motor also available. Complete and in good condition (still installed at a factory in UK).

Farrel Pomini Model OOC Lab Banbury Internal Mixer machine number: 7511, Year: 1976 Net Volume: 4.24 Litres pneumatic hopper 30kW DC variable speed motor. Complete with control panel etc and in very good condition.

Thyssen Krupp model GK270NC Banbury type internal mixer, 4 wing tangential rotors, Year of manufacture: 2003 Latest Continental design chamber! Hydraulic hopper + power pack. Body and hopper only in good condition. Unidrive gearbox and motor can be quoted for if required (same centres as 11D or F270).

Collin Two Roll Lab Mill, Roll size: 150mm dia x 400mm wide Hydraulic nip adjustment, Model: WALZWERKE 150, Year of manufacture: 1988, Power: 19kW Electric roll heating with oil - operating temp 50 to 220 C Each roll variable speed from 0 -30 rpm Manual lubrication, programable controls. In very good condition. Manuals/drawings available.

Material: stainless steel Engine: 7,5 kW Convey length: 2850 mm Convey width: 500 mm Very good condition. You can also get the entire system with all components.

WESTFALIA MZA 10 dynamischer Inlinemixer, Kapazität abhängig vom Produkt.

Material: stainless steel (1.4541) Engine: 7.5 kW Content: 500 ltr Weight: 1000 kg Length x Width x Height: 1200 mm x 1200 mm x 3100 mm With jacket 22 rpm Very good condition. We plan and build for the complete system from used and new machinery, exactly for your needs. Are you looking for something else? Write us below!

Weight 1750 kg Length x Width x Height 1800 mm x 1350 mm x 3000 mm Machine data: rotor diameter - knife circle : 500 mm length rotor : 630 mm angular speed rotor : appr. 650 min-1 after-run duration : appr. 60 sec. motor power - depent of order: 37 kW / 1500 min-1 45 kW / 1500 min-1 idle power :appr. 30 - 40 % of nominal power. Very good condition, ready to work. You can also get the entire system with all components.

Material: steel Engine: 37 kW Weight: 900 kg Length x Width x Height: 1300 mm x 1000 mm x 900 mm Applicable for production of finest plastic-powder: - finest powder without use of nitrogen - best powder characteristic: best flow behaviour, high apparent density and narrow particle distribution - low grinding temperature, in terms of optimal ducting of the air - fully automatic continous operation - simple regluation of particle size. Throughput rate : 50 - 200 kg / h. Very good condition. Are you looking for something else? Write us below! WE PROJECT AND BUILD YOUR ENTIRE PLANT EXACTLY FOR YOUR NEEDS FROM USED AND NEW MACHINES.

Material: stainless steel Engine: 160 kW Content: 15000 ltr Weight: 11000 kg Length x Width x Height: 6300 mm x 2200 mm x 2500 mm Mechanism SDW (340kW) Flender Speed: 1500 / 63 More details on request. Very good condition. You can also get the entire system with all components you need.

Crosscut and miter saws with maximum cutting height of 200 mm stable grey cast iron construction precise ball bushing guide of the tool slide on hardened and ground steel shafts Manual saw feed fast up to 65 ° horizontal MITRE setting and 60 ° vertical for adjustable fixed stops lower blade guard to extractor can be connected Machine mounted on mobile machine base with 1,5 mtr. long rollers left and right left side with scale and stop position slider Technical data: Engine: 400 V / 5.0 kW Speed: 2800 RPM Cutting length: 420 mm (at 90 °) Cutting height: 200 mm (at 90 °) Miter range horizontal: 45°-90° - 20 ° Miter range vertical: 60° - 90°-30° Saw blade diameter: 520 mm Dust nozzle: 100 mm Weight: 490 kg

Material: stainless steel Engine: 57 / 40 kW Weight: 7500 kg Length x Width x Height: 2900 mm x 1650 mm x 2000 mm Nominal volume : 2500 ltr. Working pressure : 5 bar electric input power : 380 volt / 50 hertz. Machine with withdrawable mixing device. You can also get the entire system with all components you need. Write us below!

Material: steel Engine: 75 kW Pin-disk Capasity factor: F=ca. 6,3 Drive: 75 kw Speed: 4900 The machine is as good as new. You can also get the entire system with all components.

Very good condition, like new. We plan and build the whole plant exactly for your needs. Are you looking for something else? Write us below!

Other data and price on inquiry. Do you need another machine or the whole arrangement? We have more than 1000 other used machines on stock. Please send us an email with your need.

Material: stainless steel Year of manufacture: 1980 Content: 1000 ltr Weight: 350 kg Length x Width x Height: 3800 mm x 1900 mm x 1900 mm Drive shaft: 6,8 kW, snail 0,6W; Drive snail: 80 1/min. We develop, plan and build for you the whole plant exactly for your needs from new and/or used machines. More then 1000 used machines on stock. Write us below!

Material: Steel Engine: 15 kW Other data and price on inquiry. You can also get the entire system with all components.

1 x Carter model MK3 Plus Banbury internal mixer, Serial number: 8-77, Year: Sept 1977, Chamber volume 90litre, approx batch weight: 85kgs, pneumatic hopper, S.S.A. type dust stops, Oil cooled roller bearings, hydraulic drop door + linear actuator, cored rotors with rotary joints fitted, flood cooling to body, standard bullgear drive with 150kW, 495rpm, 3ph,m 50Hz, 380/415V slip ring motor and starter. Key interlock safety system. Complete with all operator controls, pneumatics, hydraulics etc and in good condition.

1 x Farrel 9in dia x 18in wide Two Roll mill, Machine number 72M0563, Year: Mar 1972, Swing sided type, Roller bearings, variable speed motor roll (to give variable friction), Cored rolls with rotary joints fitted, Adjustable material guides. Complete with all guarding and controls etc and in very good condition.

Material: Normal steel Fan percussion More information and price on request The machine is extensively overhauled and then is as new as new.

1 x Farrel Bridge model 11D Banbury internal mixer, machine number: 90R2022, Year: July 1991, Pneumatic hopper + extension neck, SSA dust seals, 2 wing rotors, Hydraulic drop door with Linear actuator, Wyco semi unidrive gearbox, with 875Kw, 440V AC variable speed motor with Alston syncdrive controls. In good condition.

Material: stainless steel Engine: 37 kW Content: 600 ltr Pressure (inner): 6 bar Weight: 750 kg Length x Width x Height: 2500 mm x 950 mm x 1500 mm Very good conditon, ready to work. Do you look for whole plant or have a questions? We have more then 1000 used machines on stock.

- with lateral Kappsaege

1 x Farrel 9in dia x 18in wide Two Roll mill, Machine number 72M0563, Swing sided type, Roller bearings, variable speed motor roll (to give variable friction), Cored rolls with rotary joints fitted, Adjustable material guides. Complete with all guarding and controls etc and in very good condition.

1 x Bridge 84in x 26in/22in dia two roll mill, manual nip adjustment, Cored rolls with rotary joints fitted, Bronze bush type sleeve bearings, with Hagglunds hydraulic drives fitted to each roll, 160kW motor with pump to each roll for variable roll speed/friction. Drives fitted in 1988 (Marathon type). Complete with controls etc and in good working condition. Fabricated bedplate.

Technical description: -connection achievement: 2 kW - tax tension: 24 V - connection tension: 400 volts - air pressure connection: 7 cash - saw blade: 300 mms ? - max. saw width: 150 mms - max. saw height: 100 mms - length poster table: 4,000 mms - length outlet table: 2,500 mms - saw is tiltable about control - poster is positionable about control

1 x Farrel Banbury internal Mixer, Model 00C. Machine number: 91M7017, Year: 1992, Stainless steel jacketed swing side (drop door design). Maximum steam or water pressure 150psi, chrome plated two wing cored rotors with spherical roller bearings, gross capacity of mixing chamber 4.24 liters. 5" Diameter ram cylinder, maximum pressure 100psi. Chrome plated single slope V-bottom, stainless steel, pneumatically operated front door, F.Y.A. dust stops, oil seals, oil injector, thermocouple. With 65kw (87hp), 340/440 volt, 1500 rpm motor, reducer ratio 15:1. Unit mounted in an enclosed cabinet with a pull-out discharge drawer. Includes an operator panel. In good condition.

Valvematrix with 6 DN65 UNIQUE mixproof valves, with balanced bottom channel. Yom. 2002, excellent condition.

Mixproof valve DN80, with welded valvehousing and balanced bottom channel. 3 pieces available Yom 2006, excellent condition.

Mixproof valve DN65, with welded valvehousing and balanced bottom channel. 7 pieces available. Yom. 2006, excellent condition.

Important and outstanding design features of the RaptorX-SL with steel substructure / gantry design RaptorX-SL1200/S20 The range of applications of a RaptorX-SL CNC Fraesmaschine is variable due to the adjustable working area (through-lasshoehe under Bruecke: 150mm, 300mm or 400mm ) and the travel height of 300mm in the Z-axis (at no extra charge) extremely large. special size (on one piece) x 3000 mm x 600 mm are feasible ! If you are interested please ask ! To such a way that you are able to process plate materials with the greatest stability of the Z-axis exactly as accurately as 200mm high 3D-Koerper. Use the system as a plasma cutting system or water jet cutting system, are available In the middle range of the machine (between the foottubes) you can even process parts up to a height of 850mm (beam rail etc. ) or 3D body up to about 400mm height ( at 400mm long F ...

Important and distinguishing design features of the RaptorX SL steel base machine / gantry RaptorX-SL1200/S20 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method t ...

Important and outstanding design features of the RaptorX-SL with steel substructure /RaptorX-SL3200/S15 The application variety of a RaptorX-SL CNC Fraes machine is variable due to the high-adjustable working area (read-through he under bridge variable : 150mm, 300mm or 400mm ) and the travel height of 300mm in the Z-axis (without extra charge) extremely large. special coarseness up to 17,500 mm (on one scale) x 3000 mm x 600 mm are possible ! If you are interested, please ask ! So you are able to process plate materials with the greatest stability of the Z-axis just as precisely as 200mm high 3D-coerpers. Use the system as a plasma cutting system or waterjet cutting system, corresponding extensions are available. In the middle range of the machine (between the footpipes ) you can even process parts up to a height of 850mm (beam shroughl, etc. ) or 3D body up to about 400mm hei ...

Important and distinguishing design features of the RaptorX SL steel base machine RaptorX-SL3200/S15 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objec ...

Specifications / Technical Data S-1000 CNC-Fraese and Engraving Machine The almost largest CNC machine in the High-Z series. With an external dimension of approx. 1350 x 800mm still handy enough and extremely powerful. With the High-Z CNC unit, they acquire an all-round talent in TUeV-certified quality (EMC). Whether you want to clamp complex parts on a groove table or, or to clamp factory tins into a high vice (the machine is on a frame construction, is driven in X via 2 motors and thus allows to be placed completely over a part to be machined). or simply want to do engraving or drilling then they simply work on a flat base, on which they then attach e.g. an MDF plate, which they once overfrave plan and are then able to work up to approx. +-0.02mm exactly in depth. All CNC portal fraes machines are supplied with coloured energy chains on all axes due to the improved cable guid ...