gas mwm used for sale

120651 Hoofdgedeelte van de fakkel NIEUW 2405 GEMAAKT IN DE VS 2 stuks op voorraad, NIEUW

Auction-ID: A1-40898-146

Auction-ID: A1-40898-251

Auction-ID: A1-40898-409

MicroStep 2x plasma 6000 x 3000 mm Longitudinal travel X-axis: 6500 mm Cross travel Y-axis: 3300 mm Cutting capacity: 60 mm Table dimensions: 6000 x 3000 mm Plasmasource: 2x Kjelberg HiFocus 360 amp

EKU C9F-6GS 6 Burner Natural Gas Stove Hob (gas burner) Number of burners: 6 stand-alone gas burners. Burner configuration: Divided into two performance classes for flexible pot sizes: 3 x small/medium-sized burners: 3.5 kW each (burner head Ø approx. 80 mm) 3 x large power burners: 6.0 kW each (burner head Ø approx. 110/120 mm) Total power hob: 28.5 kW gas output. Equipment: Cast-iron pot supports (slide shelf) and thermoelectric ignition fuse on each flame for maximum operational safety. Oven (undercounter)Type: Gas-powered large-capacity oven (statically heated) with piezoelectric ignition. Oven power: approx. 8.0 kW to 9.0 kW burner power. Inner dimensions: Suitable for Gastronorm grates and trays (GN 2/1). Temperature range: Adjustable from 100 °C to 300 °C via a safety gas thermostat. Connected loads Total connected load (gas): approx. 36.5 kW to 37.5 kW (sum  ...

Sold without shelves. Auction-ID: A1-49997-83

- Toyota Forklift / Forklift - Propulsion: Gas / LPG - Engine: Toyota 4P gas engine - Engine number: 4P0004697 - Serial number: 11045 - Operating weight: approx. 2.6 t - Equipped with Kaup lifting device - Lift mast with hydraulic lifting function - Fork carriage with two forks - Pneumatic tyres - Overhead guard - Driver's seat with seat belt - Lighting and exterior mirrors available - Manual control levers for travel and hydraulic functions - Rear-mounted gas cylinder - Classic Toyota instrumentation - Paintwork: Red - Visible signs of wear due to age and service life - Paint chips, scratches and corrosion build-up, especially on the lift mast, forks and bodywork - Forks with clear superficial traces of rust and wear - Engine compartment and aggregates with age-appropriate soiling - Tires optically used - Seat and controls with signs of wear - Year of construction and ...

HAVE A GDY SIR; WE VE NEW UNUSED NAPIER NA 295 TURBOCARGER AS COMPLETE. PLS FIND SPEC AT BELOW. INLET HAS 4 HOLES NAPIER: 295 FRAME LETTER: JH SPECIFICATION: J793 SERIAL NO.: 710083 MAX SPEED: 31000RPM MAX TEMP: 650 C. ALTERNATION NO.: 13678910 SUPLIED ON 28-10 - 2013 AIR FILTER ELEMENT DTLS 75155/248179/2 EJ5385 Issue 4 IT IS STOWED AT ORIGINAL WOODEN BOX. NEVER USED. READY TO TRANSPORT. IF YOU'VE ANY FURTHER QUESTIONS PLS DO EMERGENCY HRSITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best regards Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

We offer two Ford gas cogeneration plants for sale. Synchronous generator: Emod 19 KVA Engine: Ford Voltage: 230 / 400 3 phases Frequency: 50 Hz Speed: 1500 rpm COS phi: 0.8 Starter: 24 V Weight: 900 kg Year of construction: 1996 Hours of operation: 24,000

Agilent Gaschromatograph model 6890/G 1530A Detector FID/EPC, Injector S/SL /EPC HP-IB and Jetdirect card upon request with Autosampler and Agilent Chemstation

SUB: FOR SALE... USED 2 SET BBC COMPLATE VTR 714E-32 T/C AT TURKEY... EMERGENCY HAVE A GOOD DAY. .WE HAVE USED 2 SET BBC COMPLATE VTR 714E-32 T/C AT TURKEY. AND READY TO LOAD ON TRUCK. OUR T/C SPECIFICATION AS BELOW MOY 1988 SERIAL NO.: X. 140769 / 140770 V 01113 R - H 04010 W 05206 E 03010 U 03 I 01800 T 01100 BOTH T/C ARE IN VERY GOOD CONDATION. IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurlubay BEST of regards; Aliaga marine services E-mail: info@aliagamarine.com PHN/fax: + 90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

FOR SALE NEW UNUSED ABB VTR 254-11 COMPLETE TURBO CHARGER IN WOODEN BOX. TO WHOM IT MAY CONCERN; WE VE NEW UNUSED ORIGINAL ABB VTR 254-11 COMPLETE TURBO CHARGER WITH ORIGINAL PACKAGE IN WOODEN BOX AT OUR STOCK. PLS FIND SPECT AT BELOW.. TYPE VTR254-11 HT 841632 t Mmax 680 C t Bmax 650 C N Mmax 523 N Bmax 497 SFUS01 YOB 2015 WEIGHT 650KG EX OWNER SUPLIED FROM WARTSILA. MADE IN SWITZERLAND. IF YOU VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US . Capt. Ayhan Ugurluba BEST REGARDS; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

FOR SALE... OVERHAULED TURBOCHARGERS ABB VTR 254-11 & BBC VTR 214-11 TO WHOM IT MAY CONCERN; WE VE BELOW LISTED OVERHAULED & REPORTED TURBO CHARGERS AT OUR STOCK. READY TO TRANSPORT AND USE... ABB VTR 254-11 HZTL 428765P2 nNmax 523 nBmax 497 tMmax 680 C tBmax-650 C SFUSO1 YEAR OF BUILT 2010 MADE IN SWITZEWRLAND BBC VTR 214-11 NoHT 399285 their 635 Tmax 680 V 01113 R 012 H 04109 W 12206 E 03221 U 023 YEAR OF BUILT 2012 MADE IN SWITZERLAND IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CIONTACT WITH US. Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Complete gas measuring station / gas detector device, including Dräger Polytron 2 IR Ex 334 etc. used Manufacturer: Dräger Type: Polytron 2 IR Ex 334 Condition: Used - top condition Price: The total price of the complete system is only 50% compared to the sum of the usual market prices of all assembled used parts. The complete gas measuring device is mounted on a mounting plate of a control cabinet and consists of: - Mounting plate 110 x 170 cm - Air suction pump - Gas measuring device Dräger Polytron 2 IR Ex 334 - Brooks variable area flow meter 1355 / D1D4A1Z5BA00 - Switching amplifier Pepperl u Fuchs KFD2-SR2-Ex1.W - 2 Pepperl u Fuchs KFD2-STC4-EX2 transmitter power supplies The air is sucked in by the pump and fed into the gas detector and measured. Function guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. Since we  ...

Gas filling device / scale with rolling landing Manufacturer: Ninnelt International GmbH Type: CTE 110 In good condition!

Further information on request

The ZAKMET FIRECUT CNC 1325 13000 X 2500 gas plasma cutter was produced in 2011. The machine is equipped with Hypertherm EDGE'Pro digital control. The burner's working area is 13,000 mm long and 2,500 mm wide. The running elements of the cutter are lubricated with the Memolub 3.0 central lubrication system. Technical data of the plasma burner: - machine working area (L x W x H): 13,000 x 2,500 mm (additionally 700 mm) x 200 mm - maximum table load: 15 kN / m2 - machine supply voltage: 3x400V AC 50 Hz - central lubrication: Memolub 3.0 - minimum temperature of the working environment: +5 degrees C - maximum temperature of the working environment: +60 degrees C - machine dimensions (L x W x H): 14500 x 5500 x 2000 mm Plasma cutter equipment: - CNC control: Hypertherm EdgePro - ventilated section table: 1550 x 2600 mm - 9 segments - gas burner: type MS 3452 \ 250-PM (x2) - ...

Gas filling facility with weighing technology / scale manufacturer: Ninnelt International GmbH Type: What 110 p In good condition!

Horiba Here we offer you a Horiba exhaust system Mexa 7100D. Including JAG-10-000-061 bottle trolley approx. 1200 x 1064 x 802 mm and OVN-724A Stationary exhaust gas measurement before/after exhaust gas aftertreatment, Assessment of exhaust gas aftertreatment systems Modal analysis (dynamic or transient analysis) during transient operations Analyzer for CO/CO2 (HC, NO, N2o, SO2), O2, THC 200 operating hours Weight 620 Kg Year of construction 2016 Type: Mexa 7100D Condition: used Pick-up from location Scope of delivery: (See picture) (Changes and errors in the technical data, information reserved!) We are happy to answer any further questions you may have on the phone.

Make and Model: GE WHG-125 Year: 2011 Hours: 6000 approx. Year : 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: These units have been decommissioned and been in storage since May 2016. Unit 1 and 2 had a report of an MBC fault (magnetic bearing controller). Unit 3 has several parts missing due to a failure in the power electronics. Some parts of the Power electronics, PLC, speed drive for the refrigerant pump are missing. Unit 4 had a failed heat exchanger and filled the ORC with water, would need stripping to determine the full extent of the repairs needed. Extra : These units run on a working fluid (refr ...

Key data: 117

Make and Model: GE WHG-125 Year: 2011 Hours : 16,000 & 35,000 Capacity kW: 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: The containerised units were decommissioned towards the end of 2018. Both of the units were operational before decommissioning. Unit 1 has the upgraded 3600 MBC (magnetic bearing controller). Both of the units are containerised at present but can be removed . Extra: These units run on a working fluid (refrigerant R245Fa) that does not come with the units as this was sent for recycling after commissioning. This will need to be purchased and filled during installation and commissioning.  ...

2 x 2.9MW 60Hz NIIGATA 18V22AG Gas Power Plant for sale NIIGATA says that 18V22AG has a high electric thermal efficiency of 40% or more and the 22AG engine produced 30% higher power than a conventional spark ignition gas engine with the micro-pilot compression ignition system. Produced in 2004, this generating sets had been successfully operated about 32,000 hours and had a good condition as seen in the photos and the plant was dismantled and has been well preserved in our factory and ready for immediate delivery. Main Specifications: - Engine Model: 18V22AG x 2 sets - Maker: NIIGATA - Continuous Output: 2880kWe x 900 rpm - Frequency & Voltage: 60Hz & 6600V - Year of Production: 2004 - Running Hours: abt. 32,000 hours - Fuel Oil: Natural Gas - Plant Auxiliary Equipment: 1 set ■ Main Specifications ▣ Gas Engine Maker NIIGATA Model 18V22AG Quantity 2 sets Ye ...

ECKERT AGAT SPEED gas cutting machine was manufactured in Poland in 2014. The machine designed for precision cutting of metal sheets with a maximum thickness of 100 mm is distinguished by a high-quality portal with an open structure, ensuring excellent stability during the performed cutting process and free access of the operator to the working space. The contamination generated during the cutting process is continuously removed by a sectional extraction table covering the entire working area of the machine. The ECKERT gas cutting machine is also equipped with, among others, a state-of-the-art CNC ECS 872 controller and an oxygen torch support with capacitive distance sensor. Technical data of the ECKERT AGAT SPEED CNC cutting machine - CNC control: ECS 872 - maximum workpiece thickness: 100 mm - work table surface (L x W): 3000 x 2000 mm - oxygen torch support with capacitive dis ...

Key data: 588

2 x Jenbacher 320 Wood gas / Syngas. We have for sale a complete generating station for syngas, including gas line, circuit breaker, control panel and radiator. Two low-hour wood gas / syngas generators in great condition. These generators were only run on natural gas. They are currently set for wood gas / syngas. All wiring between control panel and alternator has been marked up. Available for immediate delivery. For use on gas from pyrolysis plants, gasification plants, woodgas and synthesis gas. Capacity: these generator sets are rated at 588kW for syngas. If they are run on other gases they could produce 720kW. Make and Model: Jenbacher 320 Fuel: Wood gas / Syngas Year: 2008 Hours: 3,000 Capacity: 588 / 720 kW V: 400 HZ: 50 Scope of supply: Engine, alternator, frame, control panel, switch panels, gas line, radiators, wiring and other accessories. Avail ...

Complete MTU E3042Z6 Combined Heat and Power Natural Gas Generating Set CHP With Acoustic Canopy. Ready to run, turnkey low-hour CHP generating set with acoustic canopy. New exchange block was installed 10,000 hours ago (total hours for set 30,000). Engine is in great condition and available for immediate delivery. Make and Model: MTU E3042Z6 Hours: 10,000 Year: 2017 Capacity: Electric Power 390 kW Thermal Power 490 kW Heating water inlet / outlet 70 / 90 C Fuel: Natural Gas Voltage: 400 HZ: 50 Scope of supply: Engine, Alternator (Leroy Somer), Base Frame, Control Panel, Gas line, Piping, Pumps, Exhaust, Intercooler, Cabling from control panel to alternator, Acoustic Canopy, Documentation.

5,000 litre storage containers According to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. The tank has two saddle feet, a manhole DN 500 with domed lid, is used, inside empty and professionally cleaned and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube,. 1 sounding pipe provided with dip stick and sounding Rod seal, 1 vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fluid. The container is outside new primed and painted. L = 2.80 m / D = 1.60 m / weight CA. 1.3 tons. / free charged ex works. Description PTO pump: Non calibratable type eco-box-55- Capacity up to approx. 55 l / min. suitable for diesel fuel, incl. -Automated fuel dispenser with PC softwa ...

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Setting range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Design mobile compact system Wire feed 4-roll drive Hedging 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, very good, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece glass 90 x 110 mm white 1 piece protective glass 90 x ...

Key data: 220 °C, 2000 mm

PULVERBESCHICHTUNGSOFEN Verwendungszweck : Pulverbeschichtung Maximale Temperatur : 220ºC NUTZBARE INNENABMESSUNGEN Länge : 2.500mm Breite : 1.200mm Höhe : 1.800mm Material der Außenfläche : 1mm Kohlenstoffstahlblech, außen pulverbeschichtet Material der Innenfläche : 1mm verzinktes Stahlblech, nicht beschichtet Dicke der Isolierung : 150 mm Isolierung : Boden - 50 mm Steinwolle (50 kg/m³) Seiten- und Deckplatten - 150 mm Steinwolle (50 kg/m³) Wärmeübertragung : Konvektion, durch geschlossenen Luftkreislauf Heizungsart : Indirekte Heizung mit Wärmetauscher Temperaturregelung : Ein/Aus, 0-400ºC Digitaler Thermostat, Fe-Const (J-Typ) Thermokupplung Umgebungstemperatur : +10ºC (während des Betriebs) Gleichmäßigkeit des Ofens: ±2,5ºC (5ºC insgesamt) Regelgenauigkeit: ±1ºC Aufheizzeit : 25-30 min (leerer Ofen) Energiebedarf des Ofens : 30.000 kc ...

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 3000 D Connection voltage 3 x 400 volts Setting range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current setting 14 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Execution of mobile industrial plant with separate DV case Wire feed 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 940 x 445 x 1,040 mm Weight 140 kg Special accessories VB-cable 1.6 mtr. Long Age 9 months Condition very good, as new Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece pro ...

Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 320 K Plant No. 118.362 Connection voltage 3 x 400 volts Setting range 25 - 320 amperes Switch-on time 40% ED at 300 amperes 60% ED at 270 amperes 100% ED at 240 amperes Current setting infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Design portable assembly system Wire feed gearbox 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 600 x 300 x 565 mm Weight 32 kg Age 6 months Condition workshop-tested new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 pie ...

Number: VH503 Number: 1 piece Control cabinet for the continuous gas analysis for measuring gas preparation Cabinet disc is available and whole! Delivery possible by arrangement Make: ABB Type: unknown Extract of the component list: ABB Measuring gas conveying unit Advance SCC-F ABB Measuring gas cooler Advance SCC-C RITTAL Filter Fan SK 3326100 WINKLER Filter for electrically heated sample lines AF2055/06/200 DURAG 2 unit of operation & evaluator for combination probes D-RX 250 FESTO 2 valve & filter blocks Collecting container among other things, Dimensions:. 2000x800x650 mm (HxWxD) Weight:.. approx. 180 kg

FOR SALE COMPLETE T/C ABB VTR 454-32 TO WHOM IT MAY CONCERN; WE ARE ABLE TO SUPPLY USED COMPLETE T/C ABB VTR 454-32 AT TURKEY PLS FIND SPECIFICATION T7C AT BELOW. TYPE VTR 454-32 HT 833511 N of Saad 290 Nbmax 276 t Saad 580 tbmax 550 YOB 2005 SWITZERLAND IF YOU'VE ANY QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US Capt. Ayhan Ugurluba With child of regards; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

FOR SALE... 2 SET T/C TO TCR 18-42065 YOB 2010 AT TURKEY HAVE A GOOD DAY SIR. WE VE 2 SET COMPLETE T/C TO TCR 18 - 42065 AT OUR STOCK. PLS FIND TURBO CHARGER SPECT AT BELOW. TYPE: TCR 18 - 42065 WORK NO: 7642160 / 7642161 SPEED: 37300RPM T MAX: 650C. YOB: 2010 IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST of regards; Aliaga marine services E mail: info@aliagamarine

Sealing plates 1.5 x 1.5 m from 2 to 8 mm thickness. Asbestos-free. Made in Germany Price â?¬ 2,00 / kg

MAN 2876 LE302 gas engine (biogas) 190KW (also as 210KW-Version) It's a replacement engine for various biogas CHP. Overhauled according to manufacturer guidelines and RAL quality seal(maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a quotation. We have other Exchange engines (2848 with 250KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers, etc. and other components and spare parts for MAN gas engines in stock.

MAN 2848 LE322 gas engine (biogas) 250KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

MAN 2842 LE322 gas engine (biogas) 370KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2848 250KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

HAVE A GOOD DAY SIR. WE VE NEW UNUSED. MITSUI MAN NA 57 TO 725 P IT STOWED AT FABRIQ WOODEN BOX. IT WILL NEVER MOUNTED AND USED. PLS FIND SPEC AT BELOW. READY TO TRANSPORT. EX STOCK. MITSUI MAN: NA 57 TO 725 P NO.: 2430 SPEC AD: 490 A4K : 404.3 REVOLUTION: 15000 RPM MAX TEMP: 600 C IF YOU'VE ANY FURTHER QUESTIONS PLS DO EMERGENCY HESITATE TO CONTACT WITH US. READY TO TRANSPORT. EX STOCK. Capt. Ayhan Ugurluba Best Regards ; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

We offer for fast CHP Scania DC12-16 motors/hull motors in exchange. MIW Motoren-Instandetzunsg-Werk GmbH North-West Ring 8 D-27404 Zeven/Germany E-mail= info at miw-zeven

We are stocked for CHP Fast with Scania Motor DC12/16 fuselage motors. MIW Engine Repair Plant GmbH North-West Ring 8 D-27404 Zeven/Germany e-mail: info at miw-zeven

Complete 48 MW Westinghouse W251-B11A Gas Turbine with a Brush electric generator, 3000 rpm, 50 HZ, 11.5 KV, may be modified as Dual Fuel GT ied

Key data: 1000 , 1250 , 400

WAUKESHA P9390GL 1 MW 400V / 50 Hz / 1000 rpm, only 6000 hrs, year 1996, dismantled from Landfill station

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2800 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 30% ED at 280 amperes 60% ED at 210 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 4-wheel drive DV 26 Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 80 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box, kpl ...

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Adjustment range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 2-roll drive Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll of welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of lens 90 x 110 mm white 1 piece of protecti ...

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2000 K Connection voltage 3 x 400 volts Adjustment range 25 - 200 amperes Switch-on time 30% ED at 200 amperes 60% ED at 140 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 2-roll drive Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 70 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch, 3 mtr. Long 1 piece ground cable 4 mtr. Long 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box ...