gas engine deutz used for sale

Make and Model: GE WHG-125 Year: 2011 Hours: 6000 approx. Year : 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: These units have been decommissioned and been in storage since May 2016. Unit 1 and 2 had a report of an MBC fault (magnetic bearing controller). Unit 3 has several parts missing due to a failure in the power electronics. Some parts of the Power electronics, PLC, speed drive for the refrigerant pump are missing. Unit 4 had a failed heat exchanger and filled the ORC with water, would need stripping to determine the full extent of the repairs needed. Extra: These units run on a working fluid (refri ...

Key data: 117

Make and Model: GE WHG-125 Year: 2011 Hours : 16,000 & 35,000 Capacity kW: 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: The containerised units were decommissioned towards the end of 2018. Both of the units were operational before decommissioning. Unit 1 has the upgraded 3600 MBC (magnetic bearing controller). Both of the units are containerised at present but can be removed. Extra: These units run on a working fluid (refrigerant R245Fa) that does not come with the units as this was sent for recycling after commissioning. This will need to be purchased and filled during installation and commissioning.  ...

Gas forklift Yale Type: GLP-030AUA V Serial No.: Y382072 Year of construction: 1982 Weight: 2,780 kg Capacity: 1,500 kg Battery voltage: 12 V Forklift truck is fully functional and is protected with us in the Hall. Can be visited at any time! In very good condition!

Make and Model: GE WHG-125 Year: 2011 Hours : 7155 and 6849 Capacity kW: 117 HZ : 50/60 Voltage: 400/480 V Scope of supply: Each ORC skid has its own heat exchangers for evaporation and condensing of the refrigerant (working fluid). You would need to install a water heat source and a water cooling circuit, no cooling towers or blowers are included with what we have in storage. Condition: These units have been decommissioned and been in storage since May 2016. Both of These units were operational at the time of decommission. Extra: These units run on a working fluid (refrigerant R245Fa) that does not come with the units as this was sent for recycling after commissioning. This will need to be purchased and filled during installation and commissioning . Price: €70,000 each

5,000 litre storage containers According to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. The tank has two saddle feet, a manhole DN 500 with domed lid, is used, inside empty and professionally cleaned and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube,. 1 sounding pipe provided with dip stick and sounding Rod seal, 1 vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fluid. The container is outside new primed and painted. L = 2.80 m / D = 1.60 m / weight CA. 1.3 tons. / free charged ex works. Description PTO pump: Non calibratable type eco-box-55- Capacity up to approx. 55 l / min. suitable for diesel fuel, incl. -Automated fuel dispenser with PC softwa ...

Praezision tube Residual bestaend from the production of gas pressure cylinders Stainless steel, probably V2A or V4A Laenge each 6m The following dimensions should be available, exact quantities on request or on order. 3x20 7x23 4x28 1x40 Sale against bid either as a total length or by length or by meter Special price

Electric pumping system for oil or diesel for controlled extraction of oil quantities from large containers such as oil barrels, tanks, etc. Consisting of electric motor with pump, pressure monitor, hose reel, pump gun with manual pass counter with rigid outlet. Display of the extracted quantity in litres Electric pump for fresh oil supply, suitable for barrel removal or as a tank pump, Closed hose reel for oil, hose length xxm xx" hose, with wall mount and pump gun. Special price

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 750 l/h power heating heater / oil boiler 70 kW Electrical power 1.1 kW Electrical connection 230V 50Hz (1 phase) Electrical protection 16 A Laenge 1400 mm width 900 mm Height 1850 mm Weight 350 / 450 kg Gas consumption flu acetic gas 5.5 kg/hr. Gas consumption natural gas natural gas 7.5 m3/hr. ; New machine - best condition

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 1500 l/h power heating heater / oil boiler 140 kW Electrical power 1.8 kW Electrical connection 230V 50Hz (1 phase) Electrical fuse 16 A Laenge 1715 mm width 900 mm He 1900 mm weight 500 / 600 kg Gas consumption flu vinegar gas 11 kg/hr Gas consumption natural gas 15 m3/hr. ; New machine - best condition

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 500 l/h power heating heater / oil boiler 45 kW Electrical power 1.1 kW Electrical connection 230V 50Hz (1 phase) Electrical fuse 16 A Laenge 1400 mm width 900 mm Height 1850 mm weight 330 / 430 kg Gas consumption flu vinegar gas 4 kg/hr Gas consumption natural gas 5 m3/hr. ; New machine - best condition

JENBACHER YEAR: 1997 HOURS: 23000h ELECTRIC POWER: 827 kW – 400V AC 50Hz The equipment is stowed and ready to load. This engine has been stopped regularly in 2011. VOLUME OF SUPPLY: They are integral parts of generators and groups necessary for their execution (gas input, output energy): ELECTRICAL GROUP: Engines JENBACHER 316 GS / 827 kWe Year 1997 , Operating hours: 23000h, 2 units. Alternator STAMFORD / 1000 kVA -800kW- 400V AC 50HZ Generator (alternator, motor and PLC motor) Control Panel Generator (DIANE XT) Auxiliary control panels Low voltage circuit breaker petrol train Silencer Slippers Technical documentation You can find us on Whatsapp: +34 611457522 Email: Sales@eurogensets.com

JENBACHER YEAR: 2013 HOURS: 25000h ELECTRIC POWER: 1860 kWe – 400V AC 50Hz PH 3 This equipment is properly stowed and ready to load. SCOPE OF SUPPLY The following are integral parts of the generators and groups necessary for their implementation (gas input, power output): GENERATOR: Jenbacher Model: J616 GS C02| 2000 kW| Year 2013, total hours of operation: 25000 h (15000 hours after the complete revision carried out in 2013). Alternator STAMFORD/ 1860 Kw 690V | | 50Hz 400 V AC Phase 3. Generator (alternator, motor and PLC motor) Control Panel Generator (DIANE Blue) Gas train Y- exhaust gas pipe Technical documentation of the equipment Service history: The maintenance has been carried out by LA EMPRESA LONJAS TECNOLOGÍA SL according to the manufacturing instructions. You can find us on Whatsapp: +34 611457522 Email: Sales@eurogensets.com

Gas turbine with generator model M1A-13D 2,500 hours after overhaul 50 Hz, 400 V, in excellent condition, extrated and ready for transport.

GE LM2500+ For Sale (31.3 MW, 50 Hz): GE LM2500+ natural gas-fired and associated Aalborg HRSG. The GE LM2500+ has a nominal output of 30 MW. The OCGT originally produced steam for local combined heat and power (CHP”) demand, which no longer exists. Due to this, the HRSG is kept in dry preservation and the OCGT operates using the bypass stack, providing black start and short-term operating reserve capability. Open cycle GE LM2500+ GT driving a 36 MVA generator, which is a totally enclosed air-cooled (TEAC”) design rated at 11 kV. The boiler on this unit is currently in dry preservation. The LM2500+, a design based on the very successful heritage of the LM2500 gas turbine, rolled off the production line in December 1996. The LM2500+ was originally rated at 27.6 MW, for a nominal 37.5 percent thermal efficiency at ISO, no losses and 50 Hz. Since that time, its rating has continually  ...

GE Jenbacher JW 316 GS Power Generation Unit 760 kW Gas Engine For sale is a used gas generator set or CHP, combined heat and power plant with GM Jenbacher engine in good condition Specifications: Condition: very good Engine: GM Jenbacher 16 cylinder , V16 biturbo gas water cooled Type number : JW 316 GS Power : 760 KW RPM : 1500 U/Min. Frequency : 50 Hz Voltage : 230/400 volts - Built in : 1996 - Incl. batteries -Switchboard -It was recently dismantled from the hospital building, and ran until the end without any problems. Scope of delivery as shown will be delivered like shown All our articles are dismantled, cleaned and visually checked for damage by expert personnel of our company before being sold. All article relevant data / information can be found in the description and the pictures. All information is given to the best of our kno ...

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Setting range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Design mobile compact system Wire feed 4-roll drive Hedging 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, very good, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece glass 90 x 110 mm white 1 piece protective glass 90 x ...

Used metal cabinets for storage of gas cilinders design for installation in warehouse/workshop. price €220 each

FOR SALE USED BBC VTR 2 354-11 P INLET COMPLETE TURBO CHARGER TO WHOM IT MAY CONCERN; WE VE COMPLETE USED BBC VTR 2 354-11 P AT OUR STOCK. TURBO DISMANTLED FROM MAK 8M 35 ENGINE ENGINE kW 4011 PLS FIND T/C AT SPEC BELOW BBC VTR 2 354-11 P 2 INLET HT 371508 V0111 3R011 H01111 W121 08E 03321 L181 CASING AA21 TURBO CHARGER IN GOOD WORKING CONDATION TURBO CHARGER READY TO TRANSPORT AT IZMIR TURKEY IF YOU'VE ANY FURTHER QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

FOR SALE 2 SETS YOU NR 29 / S103A COMPLETE TURBO CHARGERS AT TURKEY... TO WHOM IT MAY CONCERN; WE VE 2 SETS COMPLETE TURBO CHARGERS TO NR 29 / S103A AT OUR STOCK TURBO CHARGERS DISMANTLED FM PROPOLSUION ENGINE. PLS FIND SPECT OF TURBO CHARGERS AT BELOW TYPE: ONE NR 29 / S103A WORK NO OF T/C: 1 150 804 / 805 PLANS NO.: H 09875 TURBO CHARGERS READY TO TRANSPORT AT IZMIR TURKEY IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Centrifugal compressor in landfill gas use. Technical data sheet located as an attachment. The compressor is located in a very good condition, is until end of July 2018 in the operation and is very robust (casing). Pressure difference 180mbar and 15 kW drive motor. Radial blower used for landfill gas utilization. Technical specification see attached data sheet. The blower is in good technical condition and still in operation on a bio-gas plant in Germany untill end of July 2018. Pressure drop 180 mbar with 15kW electrical drive.

FOR SALE... OVERHAULED TURBOCHARGERS ABB VTR 254-11 & BBC VTR 214-11 TO WHOM IT MAY CONCERN; WE VE BELOW LISTED OVERHAULED & REPORTED TURBO CHARGERS AT OUR STOCK. READY TO TRANSPORT AND USE... ABB VTR 254-11 HZTL 428765P2 nNmax 523 nBmax 497 tMmax 680 C tBmax-650 C SFUSO1 YEAR OF BUILT 2010 BBC VTR 214-11 NoHT 399285 their 635 Tmax 680 V 01113 R 012 H 04109 W 12206 E 03221 U 023 YEAR OF BUILT 2012 IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CIONTACT WITH US. Capt. Ayhan Ugurluba BEST regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Machine type MIG/MAG welding system Make MERKLE Type CompactMIG 280 K Connection voltage 3 x 400 volts Setting range 25 - 280 amperes Switch-on time 40% ED at 280 amperes 60% ED at 230 amperes Current setting 14 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Design mobile compact system Wire feed 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 870 x 480 x 740 mm Weight 105 kg Special accessories Display and wire automatic Age 6 months Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories 1 piece welding torch SB 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield  ...

new gas turbine packages 16 MW each possible with OEM guarantee 50 Hz gas fired

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 3000 D Connection voltage 3 x 400 volts Setting range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current setting 14 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Execution of mobile industrial plant with separate DV case Wire feed 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 940 x 445 x 1,040 mm Weight 140 kg Special accessories VB-cable 1.6 mtr. Long Age 9 months Condition very good, as new Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece pro ...

New gas pressure regulator, Itron, DN80, RR16-80-82-12N-SL-IZN.1 Manufacturer: Itron Type: RR16-80-82-12N-SL-IZN.1 - DN80, PN16 - W DSO 35 mbar - 250 mbar Condition: The gas pressure regulator was purchased from a spare parts warehouse of a company and is still in its original packaging Dimensions: 43cm x 40cm x90cm high Weight: 63 kg

GAS stove by Babs, model: 105 043. stools. 1-burner, power rating: 0.55 kg / h, SER. No.: 78 EBQ 13 Dimensions: 430x450x500mm Elek. Power: 7kW. The mismatch? Visit our website 2hand4sale.de we have different gastro devices in range.

1 piece Elster RVG G160 DN80 PN16 Rotary gas meters, used

1 piece RMG gas Train, used, in stock

1 piece gas train RMG used in stock

1 piece RMG gas train with DUNGS prepressure regulator and DUNGS double solenoid valve, used

Second-hand Hybrid forklifter LPG gas and petrol Loading capacity 3,000kg Engine K25 Japan Long forks 1.820mm lifting height 3,000mm solid tyres Colour red Including.: Duplex mast, side shifter, seat belt, rain cover, toolbox, manual

Key data: 480 , 400

Make and Model: Waukesha VGF36GLD Natural Gas Generator Set Fuel: Natural Gas and Biogas Year: 2016 Hours: 3,900 Capacity: 480 kW Hz: 50 Voltage: 400 V CHP Complete containerized plant with urea emissions purifier. Scope of Supply: Engine, Alternator, Frame, Control system, Gas line, Water heat exchanger, Gas heat exchanger, Radiator, Switchgear, Soundproof genset container, Chimney, Pumps, Original folders, Urea emissions purifier, Special tools, Spare parts and other accessories are included. General Information: This system was used by the installer as a showcase to promote their product. Now having to promote another product, they need to sell it to install the next one. It can work both with natural and biogas. Now Available for Sale. Price: € 185,000

Number: VH503 Number: 1 piece Control cabinet for the continuous gas analysis for measuring gas preparation Cabinet disc is available and whole! Delivery possible by arrangement Make: ABB Type: unknown Extract of the component list: ABB Measuring gas conveying unit Advance SCC-F ABB Measuring gas cooler Advance SCC-C RITTAL Filter Fan SK 3326100 WINKLER Filter for electrically heated sample lines AF2055/06/200 DURAG 2 unit of operation & evaluator for combination probes D-RX 250 FESTO 2 valve & filter blocks Collecting container among other things, Dimensions:. 2000x800x650 mm (HxWxD) Weight:.. approx. 180 kg

Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 320 K Plant No. 118.362 Connection voltage 3 x 400 volts Setting range 25 - 320 amperes Switch-on time 40% ED at 300 amperes 60% ED at 270 amperes 100% ED at 240 amperes Current setting infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Design portable assembly system Wire feed gearbox 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 600 x 300 x 565 mm Weight 32 kg Age 6 months Condition workshop-tested new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 pie ...

Complet gas turbine GE LM 6000 RMUGG - 04 , low time work

Sealing plates 1.5 x 1.5 m from 2 to 8 mm thickness. Asbestos-free. Made in Germany Price â?¬ 2,00 / kg

10 tons Gaz hose (for house connection) 8 mm and 12 mm Complete roles Made in Germany â?¬ 2,00 / kg

Key data: 260 , 400

2 x CHP Schmitt Enertec Energen Combined Heat and Power units for the simultaneous production of electricity and hot water. Both units have had full engine rebuilds and are in good condition. Make and Model: Schmitt Enertec M08-BT2D22 Year: 2015 Hours: 65,600 kW: 260kW Fuel: Biogas Hz: 50 V: 400 Scope of supply: Engine, alternator, exhaust gas heat exchanger. Condition: Both fully rebuilt with new parts which include New cylinder liners, New pistons, New cylinder heads, New Conrods, New shell bearings . Unit 1: Total Run Hours: 67,000. Hours since engine rebuild: 5,000 Unit 2: Total Run Hours: 65,600. Hours since engine rebuild: 2,000 Price: £40,000 each

GEA Plate heat exchanger NT50T CDS-10 with 10 plates in very good condition Material: 1.4405 Min./Max. permissible pressure: 0 bar / 6 bar (both sides) Min./Max. permissible temperature: 0.0 °C / 100 °C Test pressure: 7.8 bar Volume: 0.82 / 1.03 L Kerb weight: 83 kg Width: 320 mm Height: 670 mm Depth: 600 mm Connections: 2x Flange DN50 2x Flange DIN 11851 (milk pipe thread) Number of plates: 10 Last refrigeration/heat medium: water-glycol mixture Seals: EPDM

GEA Plate heat exchanger NT50T CDS-10 with 10 plates in very good condition Material: 1.4405 Built: 2007 Min./Max. permissible pressure: 0 bar / 6 bar (both sides) Min./Max. permissible temperature: 0.0 °C / 150 °C Test pressure: 7.8 bar Volume: 0.82 / 1.03 L Kerb weight: 88 kg Width: 320 mm Height: 670 mm Depth: 600 mm Connections: 2x Flange DN50 2x DIN 11851 (milk pipe thread) Last heat medium: steam Seals: EPDM

GEA plate heat exchanger VT10 CDS-16 with 10 plates in very good condition Built: 03/2006 Min/Max permissible pressure: 0 bar / 10 bar (both sides) Min./Max. permissible temperature: -10 °C / 100 °C Test pressure: 13 bar Volume: 3.0 / 3.3 L Kerb weight: 133 kg Width: 290 mm Height: 920 mm Depth: 570 mm Refrigeration/heat medium: propylene glycol Connections: 4x Pipe nipple DN 50 Device can be inspected at any time in 76694 Forest upon request.

Gas-fired preheating furnace, make VEI type: VEI_KO_V_GB_400-350 temperature: 350°C burners power: 2 x 200 kW fans: 2 x 4 kW useable dimensions x 2 (h x d x w): 1.000 x 1.400 x 2.800 mm

Key data: 1095 , 400

COMPLETE TRIGENERATION PLANT INCLUDING CHILLER AND COOLING TOWER Make and Model: JENBACHER 320 G.S N-L Fuel: Natural Gas Capacity: 1095 kW Year: 2007 Hours: 50,000 HZ: 50 V: 400 30,000HR MAINTENANCE SERVICE PERFORMED IN 2017 ON 28,000 hrs. Replaced 20 Cylinder Heads, Pistons complete with Piston Rings, Cylinder Liners Replaced Main Bearings Replaced Intercooler Overhauled Turbocharger, done by a specialist company Overhauled Plate Water Heat Exchanger, done by specialist company Camshaft checked and is in good condition Other works and checks not listed were carried out according to the GE Jenbacher schedule. Scope of supply: Gas engine genset, 2 x cooling tables, Gas line, Control panel, Switchgear, Silencer, Chimney, Piping, Power cables, Control cables, Chiller and Cooling Tower. Available for Sale Now. Price: 100,000€

51 MW - CCGT comprising 3 x 12 MW Solar Gas Turbine generator and 1 x 15 MW steam turbine generator Model : TITAN 130 Capacity : 12 MW Voltage ; 11 KV / 50 Hz Qty : 3 sets Titan 130 + 1 set STG Year : 2012 Running hr : 6000 hrs since new

Complete 48 MW Westinghouse W251-B11 Gas Turbine with a Brush electric generator, 3000 rpm, 50 HZ, 11.5 KV,

WAUKESHA P9390GL 1 MW 400V / 50 Hz / 1000 rpm, only 6000 hrs, year 1996, dismantled from Landfill station

2 nos. unused MWM gas generator TCG2032V16 4.3MW 11KV / 50 Hz, year 2019

Key data: 1400 V, 1800 , 400

MWM Power Generator TBG620-V16K Gas generator set from 2001, Scope of delivery: base frame and generator, as shown. Without turbocharger, gas mixer, oil cooler and intercooler. Camshaft has signs of wear on the B side. 1 available 1,365 KWel x 1,500 rpm, 400 V/50 Hz. AC generator: Stamford HC I734G2 CG, 1,800 KVA Gas engine MWM TBG620-V16K Manufacturer: MWM Model No.: TBG620-V16K Type: Gas generator set Serial Number: 2203156 Power [KW]: 1.400 Year of construction: 2001 Hours:– Weight [kg]: 8.588 Dimensions LxWxH [cm]: 470×145 AC generator Stamford HC I734G2 CG Manafacture: Stamford Model: HC I734G2 CG Type: AC Synchronous Generator Serial Number: 0140886/06 Power [KVA]: 1,800 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 2.598 Speed [1/min]: 1,500 Year of construction: 2001 Weight [kg]: 3.700

ECKERT AGAT SPEED gas cutting machine was manufactured in Poland in 2014. The machine designed for precision cutting of metal sheets with a maximum thickness of 100 mm is distinguished by a high-quality portal with an open structure, ensuring excellent stability during the performed cutting process and free access of the operator to the working space. The contamination generated during the cutting process is continuously removed by a sectional extraction table covering the entire working area of the machine. The ECKERT gas cutting machine is also equipped with, among others, a state-of-the-art CNC ECS 872 controller and an oxygen torch support with capacitive distance sensor. Technical data of the ECKERT AGAT SPEED CNC cutting machine - CNC control: ECS 872 - maximum workpiece thickness: 100 mm - work table surface (L x W): 3000 x 2000 mm - oxygen torch support with capacitive dis ...

Item Combined duo burners, gas and oil operated Fabr.: Steinmüller, type 1: G-18-K 1120/800, type 2: DAG-18-K 1120/800, y.o.m.: 1996, Burner data natural gas burner: heat output GT operation 43.6 MW, calorific value 40.09 MJ/kg, fuel mass flow 1.089 kg/s, control range 1:8, pmax.: approx. 1,500 Pa, exhaust temperature 424 degrees, (8 units), Burner data Duo oil burner: calorific value 42MJ/kg, heating oil throughput 4,600 kg/h, max. pressure before burner 13 bar, burner working area 1:5, max. Oil pressure on the takeover 18 bar, temperature before burner 240 degrees, (8 pieces), Remark: Burners must be dismantled by the customer. The burners can also be purchased individually.