127,604 used machines on RESALE, but how to find them? Machine Search
90 Degree Curve / Curve / Conveyor / Conveyor Belt Manufacturer: Transnorm Type / Model: 1500-80 Belt Type: KT58 Condition: Used Total length outside: approx. 1750 mm Total length inside: approx. 770 mm Total width incl. motor: approx. 730 mm Total width without motor: approx. 600 mm Conveyor width/ belt width: approx. 500 mm Strap Type: Smooth Material: Aluminum/ Steel Including SEW motor (0.37 KW) Stock: 2 pieces Price per piece The conveyor system has run until it was dismantled. Condition: fully functional, with signs of wear Ideal for fast material transport Expertly dismantled and packaged Thanks to the excellent workmanship of the conveyor technology, your material glides smoothly to its destination, even under high loads. Tailor-made solutions for your intralogistics We are your competent partner for roller conveyors, belt conveyors, inclined convey ...
Manufacturer: Mc INTYRE Blade length: 150 mm Blade opening: 105 mm Cutting capacity: 25 tons Rods ST 37: 25 mm diameter Number of strokes at ¼ opening: 20 / min Number of strokes at ½ opening: 12 / min Number of strokes at full aperture: 9 / min Dimensions (L x W x H): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Control: foot pedal
Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of construction: 2008 specifications: Conveyor width: approx. 1,500 mm Wheelbase:approx. 9,625 mm Strip course: approx. 2,935 mm horizontally underfloor, then rising to a length of approx. 4,500 mm below 28°, sloping below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE as far as possible pre-assembled, consisting of: - Strip scaffolding in solidly welded section steel and sheet steel edge construction, - additional sliding guides underneath the belt support profiles in the horizontal and climbing sections to support heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with 2 ...
1 used cylinder head for Kubota V 1505 T. no obvious damage. Sale is for recovery without any warranty. Other parts are available. As well as diesel engines 1-6 cyl., various products: Deutz, Daedong, Farymann, Hatz, Iseki, Isuzu, Komatsu, Kubota, Lombardini, Perkins, Shibaura, Ruggerini, Yanmar etc. Capacity of 4,5-100 kw, used partly as new. Gasoline engines: 1-2 cylinder 3-15 kw B & S, Honda, Kohler, Robin, Wisconsin. Various cooler, starter, alternators, and mufflers in stock, various hydraulic pumps and hydraulic motors.
Key data: 1200 KW, 1500 kVA
ENGINE: MTU 12V4000G23R FREQUENCY (HZ): 50 VOLTAGE (V): 400 POWER: 1500kVA / 1200kW CYLINDERS: 12 STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 12000kg DIMENSIONS L/W/HEIGHT (MM): 500018002400 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry wit ...
Key data: 1250 KW, 1500 kVA
ENGINE: 4012-46TAG2A FREQUENCY (HZ): 50 POWER: 1500kVA / 1250(kW) CONTROL SYSTEM: DSE / ComAp FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 13388kg DIMENSIONS L/W/HEIGHT (MM): 640022002250 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry with your details and full address For more information ...
Built in 1989 Size max 320 x 400 mm Size trimmed max 305 x 380 mm Size trimmed 100 x 125 mm Product thickness max 80 mm min 6 mm Speed max 6.000 c/h Feeding height max 80 mm Equipment o infeed from the right side o automatic infeed with integrated pre stacker o cut counter o Equipment for sheet-fed o 1 set of clamping plates and holders o 3 sets of cutting sticks o 2 set of knives o external knife changing device o central lubrication o belt delivery
Claw vacuum pump Compressing dry Manufacturer: Busch Type: Mink MM 1502 AV Engine: DS 400V Suction capacity: 500 m ³/h Discharge pressure: approx. 200 mbar (abs.) Accessories: inlet filter; Operating instructions Delivery time: Please enquire; ready for operation
Manufacturer: Bush type: mink MI 1502 BP Motor: 18,5 KW; DS 400V status: used, without Warranty: 6 months Flow rate: 500 m ³/h discharge pressure: + 1,2 bar Accessories: additional intake filter (changed); Manual delivery time: approx. 1-2 where.; ready for operation
Part Number 7405 SPECIFICATIONS - max cutting height 150mm - max element width 700mm - working width of the shaft with saws 530mm - max saw blade diameter 450mm (350mm installed) 350mm - blade bore diameter 90mm in advance: -Triggers - 2 pulling shafts, toothed From below: - 2 pulling shafts, smooth - shaft with saws - Pulling shaft, smooth - 4 types of feed speeds - feed motor about 2kW - 30kW motor - machine dimensions length/width/height 2400x1700x1900mm - weight about 3000kg – Polish production – used machine, very good condition Net price: 45 900 PLN Net price: 10 432 EUR depending on the price 4,40 EUR (Prices are subject to change with higher fluctuations)
Smicon PT 1500 Fumigation / Fumigation System In a fumigation, a room is flooded with a poisonous gas to fight pests / bacteria. Because they are toxic gases, special safety measures are required. Fumigations are common in the storage of organic materials (eg grain storage, in warehouses of harbors, silos, mills), in addition, in churches to control the woodworm. It is a device which is used for the disinfection of rooms. Formaldehyde is boiled on the left-hand cooking plate and placed in a stream of air in a room together with condensed water (right hearth) to kill all the bacteria. Former list price 9.900EUR
used
Qty. 1 Second-hand Powder coil coating line on aluminium strip 1500 mm wide Mfc.: TBA Built: 1991 Coating thickness: 60 microns Revamped by OTEFAL in 2003 Powder booth changed in 2011 – GEMA Coil coater for the pre-treatment changed in 2013 Degreasing section re-built in 2010 – OTEFAL Electrical device changed in 2006 Strip width: 800 - 1500 mm Strip thickness: 0.8 – 2.0 mm A wide range of colors - over 300 different shades Capacity: 9000 tons/year in 3 shifts work 5/7 Days so 2 000 000 m² Spool dia.: 508 or 610 mm Outside coil dia.: 1500 mm Average speed: 7.5 m/min.
- Stainless steel circulating air hot air tunnel with 16 fully adjustable nozzles and digital control - Steam conditioning valves and steam extraction fans - without steam generator
oscillating belt sanding machine model VOLPATO NTS 150/C for wood edges, panels, furniture, doors, window frames and various second hand machine , like new , used very little working conditions : Excellent , like new CE regulation : Yes 45° tilting work table possibility of sanding curved pieces using the driven roller + small radius supplementary rollers diam.mm.25-30-35-40-45 mechanical oscillation with a dedicated motor via a connecting rod/crank system Technical data : Worktop mm.280 x 1000 Tiltable worktop mm.300 x 950 Sanding belt development mm.150 x 2580 Driven roller diam. mm.75 Additional worktop mm.300 x 300 Abrasive rolls available diam. mm.25-30-35-40-45 main motor power Hp 4 Motor for oscillation Hp 0.5 Oscillating stroke mm.20 Overall dimensions cm.182x105 H=cm. 150 volt. 380/50 Machine weight kg.400
Spare welding controllers for resistance welding machines also available: MPS 1033 MPS 1036 MPS 15033 MPS 15036 MPS 15043
Key data: 1200 KW, 1500 kVA, 400 V
MODEL: EQ-MTU15001200 ENGINE: MTU 12V4000G23R FREQUENCY (HZ): 50 VOLTAGE (V): 400 POWER: 1500kVA / 1200kW CYLINDERS: 12 STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 12000kg DIMENSIONS L/W/HEIGHT (MM): 500018002400 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an in ...
Key data: 1500 KW, 1875 kVA, 400 V
ENGINE: MTU 12V4000G63 FREQUENCY (HZ): 50 VOLTAGE (V): 400 POWER: 1875kVA / 1500kW CYLINDERS: 12 STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 14000kg DIMENSIONS L/W/HEIGHT (MM): 510018002400 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry with your details ...
Complete gear, from scrapped vessel. 2 pc on stock. All parts on stock for overhaul of this gear type.
Laser cutting machine MAZAK Year of manufacture: 1999 Laser power 1,5 KW CNC MAZATROL Working range: 2500 x 1250 x 100 mm Max sheet dimensions: 2500 x 1250 x 12 mm Cooling system Extraction system Transformer Pneumatic sheet metal clamp Ball support for easier positioning of the plate Technical documentation available
Key data: 150 , 394 , 50
Manufacturer/manufacturer: Krauss Maffei Typ/type: KM 110-390 C1 Year/year: 1993 Control/controller: MC 4 Clamping force/clamping force: 1500 kN Holmabstand/Dist.Betw.Tiebars: 500 mm x 500 mm Disk size/platen size: 750 x 750 mm WZ height/mould hight: min 250 max 500 mm Opening/opening stroke: 500 mm Plate distance of max/Max open daylight: 1060 mm Auger/screw size: 50 mm Stroke volume/shot volume: 442 CC / 394 gram PS Spritzdr / injection pressure: 1946 bar General / General engine power: 30 kW Heating/heating power: 14,8 kW Dimensions/dimensions: 5.5 m x 1.6 m x 2.10 m Weight/weight: 5600 kg Screen text: German Options/optional extras Core puller / core pulling: x 1 Air valve / air valve: x 1
used
Bainite (India) model BMPX150 PIN type cold feed extruders, Year of manufacture 2013 Screw diameter: 150mm L/D ratio 16:1 Output: 1200 - 1500kg/hr Power roller feed (opening 175mm), provision for cooling, Screw speed: variable max 50rpm, Max operating pressure: 340bar (5000psi) 10 rows of 8 pins (80 total) With 210kW Siemens AC v/s motor through 28:1 reduction gearbox (service factor 1.75) Hinged extrusion head with C'clamp suitable for strip All mounted on a fabricated steel base Complete with electrical controls and VFD (Siemens make). Safety features as per European standards.
Key data: 1200 KW, 1500 kVA, 400 V
ENGINE: 4012-46TAG2A FREQUENCY (HZ): 50 POWER: 1500kVA / 1250(kW) CONTROL SYSTEM: DSE / ComAp FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 13388kg DIMENSIONS L/W/HEIGHT (MM): 640022002250 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry with your details and full address For more information o ...
Key data: 1200 KW, 1500 kVA, 400 V
ENGINE: 4012-46TAG2A FREQUENCY (HZ): 50 POWER: 1500kVA / 1250(kW) CONTROL SYSTEM: DSE / ComAp FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 13388kg DIMENSIONS L/W/HEIGHT (MM): 640022002250 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry with your details and full address For more information o ...
IWKA Model CP150 Automatic Horizontal bottle Cartoner. Capable of speeds up to 150 cartons per minute. Carton size: (Length) 20mm-90mm, (Width) 15mm-60mm, (Depth) 55mm-180mm. Set up for Reverse tuck style cartons. Has Embosse coding unit , GUK sheetfed leaflet feeder .
Key data: 2300 mm, 2026 , 1615
Machine type: EVP 1500 Manufacturer: ERBA Power kW: 11 Total volume: 1500 lt. Description: The EVP 1500 vibratory finishing machine from ERBA has a flat work container base without separation. Emptying or separation is carried out via bottom emptying (manual/pneumatic). It has a fully automatic PLC process control (optional) and, on request, a reinforced suspension and a reinforced motor can be installed for higher loads. The motor speed can be infinitely variable by means of a frequency converter (optional). The price quoted is net plus the currently valid statutory sales tax and plus freight costs. The pictures can show the system including accessories, which are optionally available and associated with additional costs. The price quoted refers to the basic machine. If you are interested, we look forward to hearing from you. We will be happy to advise you without oblig ...
KUKA KR 150-2-TJ industrial robot was manufactured in 2001 in Germany by KUKA AG. This multifunctional machine is the ideal solution for automating industrial processes that require precise and reliable operation. Using the DeviceNet network protocol, it is possible to connect and configure the robot with any device, such as a conveyor gripper, welding head or plasma torch. Over the past few years, the KR 150/2 robot arm has undergone a full service and has been comprehensively prepared for operation. Some of the many overhaul works included a performance test of the inverters and motors, checking and adjusting the robot's gears, as well as replacing the batteries and the input/output module (Balluff) in the controller. Technical specifications of the KUKA KR 150-2-TJ robot - number of axes: 6 - 7-axis, 8-metre long track - controller: KUKA VKR C2 - portable teach pendant: KUKA ...
used
Key data: 490 mm, 515 mm
tock-No. 1105-04043 Type of machine CNC Turning- and Milling Center Make MORI SEIKI Type NL1500SY/500 Year of manufacture 2006 Type of control CNC Storage location HAGUENAU FRANCE Country of origin Japan Delivery time immediately Freight basis ex Warehouse Price Technical details turning diameter 490 mm turning length 515 mm control MSX-850 max. bar capacity 52 mm Travel -X Axis 280 mm Travel -Z AXIS 490 mm max. speed main spindle 6000 min-1 spindle taper 1 A2-6 C - Axis 0.001 ° Spindle bearing diameter 110/75 mm No. of tools in turret 1 12 Shaft Cross Cut 25 x 25 mm Shank diameter 50 / 32 mm Turret Change Time 0.25 s max. spindle speed driven tools 6000 min-1 rapid power traverse in X-and Z direction 30 m/min Rapids C - Axes 400 min -1 drive capacity - spindle motor 18.5 kW power capacity - driven tools 5.5 kW swing diameter over face slide 278 mm gre ...
Cast iron clamping cube Dimensions(only the cube): L 2000 x H 1500 x Depth 1200 mm 4 faces with T-slots T-slots dimensions: 58 x 36 mm Total height with enhances angle plate: 2050 mm Total height with rail: 2700 mm Weight: approx 7 T MACHINE IN OUR STOCK IN FRANCE.
Refurbished overpressure valves are offered. The blow-off pressure can be preset according to your specifications.
Y.O.M.: 1980 No.: 10027 Usable volume: 150 l Pressure double jacket: +1 bar Vacuum pump Pressure gauge, temp gauge Scraper agitator, three-way valve 3 intake ducts Lid to be opened via lifting pull Dimensions LWH: 1700 x 1000 x 2100 mm Weight: approx. 500 kg Products: e.g. mayonnaise, sauces, ketchup, cosmetics, creams etc.
McIntyre 150 Shear Designed as a low-cost answer to metal cleaning, an ordinary 13amp socket and suitable bench are all you need to put the 150 shear through its paces Versatile The McIntyre 150 Shear is ideal for all lighter metal shearing, but is powerful enough to tackle gun metal valves, bath taps, cable and other non-ferrous cleaning operations. The McIntyre 150 Shear is small enough to be moved easily around the yard and will be a versatile addition to any size of yard. Our company can provide it with short delivery time.
PVS 150 V Multicut with 15 to 22 KW with combinable cutting systems Rotor/ stator non-contact Hole disc with knife head or rotor/stator with perforated disc system 2 cutting stages
Ger RHC1500 Universal Rectifier. Indoor head. Distance between points: 1500mm. Maximum part diameter: 355mm. Point height: 180mm. Tooth diameter: 400mm. Power: 7.5hp. Weight: 4500Kgs.
Waste oil collection tank 950 litres approved for liquids of hazard class AI-III With test certificates State: Technically deficialy Optical: According to age
CoEx plate system net. 1350x1-10 mm Material: PE, PS, HIPS, ABS / Details: Main extruder RH EH2400-1-150-33V, co-extruder RH 121-1-50-30V, vacuum pump, CoEx-block, double hydr. Sieve changer with hydr. Station, wide-slit nozzle 1,450 mm, 3-roller smoothing unit RH GK-1600-60-G1 1,640 x 600 mm, Kelvi Plast temperature control unit, cooling section, side strip trim with knife beam, rubber roller extractor RH AT160-20, guillotine RAS 83.20, vacuum conveyor, CoEx dryer material, stacking device. (Ref-No. T27614)
Film recycling and granulation plant Material: PE, PP, // Cascade extruder, snail/LD x 220+150/ x 26D, drives 232 & 99 kW, water separator, hot tee with underwater cooling, only 8,500 operating hours
<b>Technical data:</b> Manufacturers; Interroll Condition: Good (Used) Max Payload: 50Kg Belt speed: 1.0 m/s Stroke time: 0.3s Rated voltage: 24V/48V Drive motor and lifting motor Control: Multi Control 6 pieces in stock <b>Tailor-made solutions for your intralogistics</b> We are your competent contact for roller conveyors, belt conveyors, inclined conveyors or telescopic telescopic applications for loading and unloading your goods! We are happy to prepare your individual offer or advise you on the conception or assembly questions. Simply let us know your needs and local conditions. Take advantage of our many years of experience and our excellent network of experts. We have already successfully implemented projects for companies in a wide range of industries, such as logistics, the pharmaceutical industry, the craft sector and the electronics ...
CNC CONTROL: MSD 501 II, FANUC FEATURES: DIAMETER ADMITTED ON THE BED, MM 680 MAXIMUM TURNING DIAMETER 440 MM N1 MAXIMUM TREATMENT DIAMETER N2 322 MM MAXIMUM TURNING LENGTH, MM 471 THE STANDARD MACHINING DIAMETER MM170 MAIN SPINDLE: STEP PANEL 45 MM COUNTER SPINDLE: HOLE PITCH LINE 43 MM TURRET 1: POSITION N12 ALL MOTORIZED TOWER 2: POSITION N12 ALL MOTORIZED
NNP Stainless vacuum tumbler, 1500Kg capacity, forward / reverse, with timer, two stainless lids, 3Ph
MABS1500 Extraction system metal for metal shavings easy filter change large collection container with drawer stable housing Engine: 1500W, 230V or 400V Suction capacity 1500 m3/h Fan wheel diameter: 300mm Suction connection: 100mm Weight 73kg
Make: YORK Type: YCSA-150-TP-380T BLUE FIN Year built: 2010 Power: 155kW Coolant: R410A 4 pieces Copeland Scroll compressors 4 pieces of fans 2 circles With WILO circulation pump 1 condenser is leaking! Price on request Contact details can be found under Contact
Lift tipper Kemper HK 150 height 330cm -for Kemper Kessel or with stage for Diosna Kessel -Height 330cm -400 volts
KW Set Lufcooled AERMEC Techn. data Aermec: • Type NRA 1500 • Cooling capacity: 390 kW • Y.O.M.: 2004; • 6 x fans; 6 x Danfoss Scroll Compressor • R 407 c; 2 circles a 44 kg; • Dimensions: B 2.2 x L 4.3 x H 2.6 m plant ran until the last, was serviced until 2019; was used for indoor air conditioning.
Te koop Endress + Hauser Flowmeter Type: Promass 80F DN 150 Serial number: 7A00BE02000 Inclusief test certificaat Number: 2.05 Voor meer info graag bellen of mailen. email: wh.derikx@gmail.com Tel: +31620758459 De nu kopen prijs is excl. 21%btw
1500Kg capacity, stainless contact parts, discharge through both sides, 3Ph
Stage bracket for Kemper HK 150 lift truck -for lifting and tilting Kemper boilers
Pre-breaker with crusher Suitable for soft lime, marl, coal Power up to 200- 600 t/h Task size up to 1500mm Drive - electric transformer station 30kV/400V Drive power approx. 500 kVA Plant weight approx. 130 tons Task bunker 25m3 Chain conveyor Roller rust Schlagwalzenbecher Deduction tape Dust removal system Caterpillar suspension - not self-driving Conveyor belt 3 x 40m Telestack, self-driving, belt width 1200mm Immediately available
all stainless steel electrically heated 4 x 9 kW frying length 1,500 mm belt width 400 mm adjustable speed oil level control manual hoists suitable for fire protection overall dimensions (l x w x h) : x 4,350 x 1,750 x 2,250 mm
maximum number of results exceeded
please refine your search
