gas beverage carbonate used for sale

Key data: 3155 , 10500

Make and Model: Rolls Royce KVSG 18 G4 The engine is from 1994. It had a full rebuild in 2004. Fuel: Natural Gas Capacity: 3155kW Hours: 63,000 HZ: 50 V: 10500 Scope of Supply: Engine, Alternator, Base frame, Acoustic Container, Exhaust Gas Heat Exchanger, Control panel and synchronisation panels. Please note: circuit breaker and transformers are not included. Price: €200,000 Available for sale from Gas Engine Exchange. Please check our complete range of equipment at gasengineexchange.com.

For sale on "as is" basis Used Solar Gas Turbine Mars 100 SoLoNOx Natural Gas Location: Europe Year of manufacture: 2012 Output Power: 11,350 kWe Heat Rate: 10.935 kJ/kWe-hr (10.365 Btu/kWe-hr) Exhaust Flow: 153,245 kg/hr (337,950 lb/hr) Exhaust Temperature: 485 °C (905 °F) Frequency: 50 Hz Package hours: 27206 Gas turbine hours: 20547 Number of starts: 216 Housed on skid installed indoor with attenuating enclosure and fire detection and suppression system. Inlet System Barrier Filter and Silencer mounted on ancillary skid on the roof of the enclosure. Gear Reduction Box RENK MAAG GmbH. Type: GPF3-28, Output Speed/Freq. 50Hz - 1500rpm Generator Data: Electric Brushless AC Generator with Permanent Magnetic Alternator. Alternator data: 2.2kW. PF.9. 1 Phase. 240V/10A/120Hz. Gen Skid includes Lube oil tank, pumps, filters, start system with AC Direct Drive AC Motor, VFD, ...

TAURUS 70 Gas Turbine Year Of Make: 2004 Total running hours: 58.000h Total hours since last overhaul 28.600h Turbine 15158 RPM 60 HZ / 15143 RPM 50 HZ Alternator 1500 RPM 50 HZ 7200 Kw at 9000 KVa 11000 Volts

Remote control for inert gas welding device, inert gas device, welding rectifier, hand controller -Manufacturer: Fronius, remote control RCU5000i Univ.SD -Art.No.: 4,046,098 -Voltage: U1 24 V -Dimensions: 180/260/H50 mm -Weight: 1.5 kg

Shock absorbers, gas pressure springs, shock absorbers, start-up dampers, impact absorbers -Piston: Ø 40 mm -Piston housing length: 377 mm -Piston rod: Ø 20 mm -Recording hole: Ø 14 mm -Dimensions: Ø 40 x 530 mm -Weight: 1.5 kg/piece

Shock absorbers, gas pressure springs, shock absorbers, start-up dampers, impact absorbers -Piston: Ø 40 mm -Piston housing length: 377 mm -Piston rod: Ø 20 mm -Recording hole: Ø 14 mm -Price: per piece -Number: 3 pieces -Dimensions: Ø 40 x 530 mm -Weight: 1.5 kg/piece

Air bellows, roller bellows, air cushions, spring-loaded brake -Gas bottle holder -for: 33.5/43.5 Lbs -Hole spacing: 115/75 mm -Weight: 3.2 kg

GE LM 2500 gas turbines 2 pcs available Power:24.000 Hp each Average working hours 1700 hours

Shock absorber, gas spring, shock absorber -Shaft: Ø 35 mm -Shaft length: 28 mm -Bore: M8 -Quantity: 8 pieces available Price: per piece -Dimensions: 75/160 mm -Weight: 3.8 kg/piece

Shock absorber, gas spring, shock absorber -Shaft: Ø 50 mm -Shaft length: 28 mm -Bore: M8 -Quantity: 5 pieces available Price: per piece -Dimensions: 95/170 mm -Weight: 6.6 kg/piece

Gas cylinder trolley, gas cylinder cart, steel cylinder cart -Transport trolley: galvanized version -Tires: pneumatic -Quantity: 1 piece available -External dimensions: 760/520/H1320 mm -Own weight: 19 kg

Gas bottle cart, gas bottle cart, steel bottle cart -Transport trolley: galvanized version -Tires: solid rubber -Number: 1 piece car available -Price: per piece -External dimensions: 730/520/H1325 mm -Own weight: 26 kg

AVAILABLE COMPLETE CHP JANBACHER 616 - Yeard 2010 With 2500kva transformer Exchanger - CHP - PANEL - complete .

Gas bottle cart, gas bottle cart, steel bottle cart -Transport trolley -Tires: PU tires puncture-proof 260x85mm -Number: 1 piece car available -Price: per piece -External dimensions: 730/500/H1150 mm -Own weight: 17.5 kg

Gas and air filters, air filters -Manufacturer: Maxitrol -Type: GF65 MF-DN65 -Dimensions: 245/199/H190 mm -Weight: 4.5 kg

Inert gas welding device, inert gas device -Max. Welding power: 340 A. -4 roller drive -Water-cooled -Incl. Ground cable -with removable wire feeder -Hose package length: 4000 mm -Dimensions: 1100/515/H1170 mm -Weight: 214 kg

Sample gas cooler -Measuring gas cooler with: protective lining -Connection: 240 volts -Dimensions: 335/560/H390 mm -Weight: 32 kg

Shock absorber, gas spring, shock absorber, start-up damper -Pipe: Ø 82 mm -Total length: 510 mm -Hole diameter: Ø 24 mm -Number: 2 shock absorbers available Price: per piece -Dimensions: 82/82/H510 mm -Weight: 11.5 kg/piece

Perkin Elmer HS 40, Headspace sampler for 40 vials, max. temperature + 210 Celsius, min. +35 Celsius, fits all gas chromator graphs,

Key data: 1067 KW

we are looking for a Jenbacher 3 1067 kw we have a biogas plant

Key data: 1950 , 2437 , 11000

Cat 3520C Gas gensets Power 1950 Kw / 2437 kVA Frequency: 50 Hz Year: 2007 20 pcs available 55.000 Working hours average

Shock absorbers, gas pressure springs, shock absorbers, start-up dampers, impact absorbers -Shaft: Ø 39 mm -Shaft length: 470 mm -Recording hole: Ø 17 mm -Number: 4 pieces of shock absorbers available -Price: per piece -Dimensions: 1755/140/H100 mm -Weight: 24 kg/piece

Remote control for inert gas welding device, inert gas device, welding rectifier, hand controller -Remote control -Manufacturer: unknown -Type: Poti -Number: 1x controls available -Price: per piece -Dimensions: 155/105/H130 mm -Weight: 2.7 kg

Agilent 5975C inert MSD with GC 6890N Agilent 5975 C inert MSD, Agilent GC 6890 N Pfeiffer Turbomolecular Pump, Electronic Ionization/EI ; GC Injector Split/splitless, EPC, LAN Agilent Backing Pump, Software Agilent MSD Chemstation for Win10

Solenoid valve, butterfly valve, flap valve, solenoid valve, solenoid valve, solenoid gas valve, gas solenoid valve, double gas valve, gas valve -Manufacturer: Siemens, double gas valve -Type: VGD40.065 -Connection: DN65 -Pmax .: 700 mbar -Dimensions: 285/190 / H210 mm -Weight: 8.3 kg

Key data: 261

Complete 2G Agenitor 406 261kW biogas generator set. We have a frame and control system along with all the other balance of plant from 2015 with 50,000hrs and a block from 2019 on 28,000hrs. Agenitor 406 Power: 261Kwh Hours: 28,000 Year: 2019 HZ: 50 Voltage: 400 Fuel: Biogas Scope of supply: Engine, Alternator, Base Frame, Gas Line, Control Panel, Circuit Breaker, Heat Island, Cooling Radiator, Silencer and Cabling. Photos 1 to 4 are of the 2019 block. Photos 5 to end are of the 2015 frame. Available for sale from Gas Engine Exchange. Please check our complete range of equipment at gasengineexchange.com.

Solenoid valve, butterfly valve, flap valve, solenoid valve, solenoid valve, solenoid gas valve, gas solenoid valve, double gas valve, gas valve -Manufacturer: Siemens, double gas valve -Type: VGD40.040 -Connection: DN40 -Pmax .: 1000 mbar -Dimension: 235/170 / H195 mm -Weight: 6.9 kg

Spiral wound gasket, labyrinth body gasket, flange gasket, high pressure gasket -Manufacturer: Frenzelit, flat gasket Novatec Premium -External: O 162 mm -Inside: O 116 mm -Thickness: 2mm -Number: 107x seal available -Price per piece -Minimum purchase: 10 pieces -Weight: 0.05 kg/pc.

Key data: 9700 , 11000

Wartsila 20V34SG complete Gas Power plant 9.7 MW 50 Hz 11K Volts Year of make 2011 45.000 Working Hours Maintanence done regularly by wartsila 20V34SG engine with all auxilaries: ABB AMG 1120LT08 Alternator, compressors, Lt Ht water tanks, LV MV HV step up Transformers, control panels, Unic control system, radiators, maintanence tanks, 2 x Napier 357 turbochargers, safety spares, Caterpillar emergency generator,Natural Gas Regulator Unit, engine tools, instruction manual and more... Please contact for more info and complete scope / offer

Complete Genset, 0 hours after M6 maintenace, damaged crancksahft. (new bearings, liners, renewed turbochargers, renewed cylinder head, new main, pilot gas valves. Lot of spare parts available.

Key data: 70

MAN E0836 E302 CHP Unit in Acoustic Canopy for Sale. Capacity: 70kW Hours: 4,500 Year: 2011 Fuel: Natural gas Voltage: 400 Hz: 50 Scope of supply: Engine, Alternator, Control Panel, Acoustic canopy, Canopy fan, Engine water pump. Footprint of the combined heat and power unit is 3.4 meters x 1.14 meters including the control panel. It has been serviced every 1000 hours. The unit is not due an overhaul until 24,000 hours. Engine has been barred over, and the canopy fan and engine water pump have been powered up. The unit is in a warm boiler room so is in good condition. Available for sale from Gas Engine Exchange. Please check our complete range of equipment at gasengineexchange.com.

For sale is a LEROY-SOMER LSA L95/4P generator with the serial number 607788/1. This generator was coupled with a Jenbacher 620 engine with the design number U320. The generator delivers an output of 2530 kVA at an output voltage of 400 V. It was manufactured in 2016 and has only 500 hours of operation since then. The price of this powerful and hardly used generator is 30,000 euros. Please do not hesitate to contact us for more information or to arrange a viewing.

Spiral wound gasket, labyrinth body gasket, flange gasket -Spiral seal: Flange seal according to DIN EN 12560-2 5 pieces/package -Type: 2 1/2 150lbs 1.4404/PTFE -Dimension: Ø124 x 2mm -Price: complete -Total weight: 0.7 kg

For sale is a Stamford HCI 734 F2 generator with serial number 96404594. This generator was coupled to a Jenbacher 320 engine with the design number 5727. The generator delivers an output of 1460 kVA at an output voltage of 400/231 V. It was manufactured in 1996. An important aspect to keep in mind is that a Megger test has been done on this generator. Please do not hesitate to contact us for more information or to arrange a viewing.

Inert gas welding machine, arc welding system, MIG/MAG welding system -Manufacturer: Ess, inert gas welding machine MIG-MAG 520-2 MW -Type: 520-2MW -Max. Welding power: 500 A -Water cooled -Wire feed case: ESS DVK 17 -Dimensions: 1160/500/H1220 mm -Weight: 379 kg

Inert gas welding machine, arc welding system, MIG/MAG welding system -Manufacturer: Ess, inert gas welding machine MIG-MAG type 310 MW -Max. Welding power: 310 A -Water cooled -Wire feeder: ESS PS 12-8 -Accessories: including hose package, ground cable -Dimensions: 1020/480/H910 mm -Weight: 208 kg

Heating, burner, gas burner, fan burner, gas fan burner -Manufacturer: Dreizler, fan burner type GE 200/300 AR 2 -Nominal heat output: 355 kW -Gas type: natural gas -Gas connection: 20 mbar -Blower motor: 0.37 kW -Dimension: 760/510/H535 mm -Weight: 33 kg

For sale is a Stamford HCI 734 FCG generator with the serial number A03C027807. This generator was coupled to a Jenbacher 320 engine with the design number B212. The generator delivers an output of 1460 kVA at an output voltage of 400/231 V. It was manufactured in 2003. An important aspect to keep in mind is that a Megger test has been done on this generator. Please do not hesitate to contact us for more information or to arrange a viewing.

GE Model : LM6000PA Power Output : 42 MWe ISO condition Voltage : 11KV Frequency : 50Hz Total 2 nos.

Key data: 3431 , 4767 , 10500

Jenbacher gas generator ( UNUSED ) , Model : J620GS-F75 Power Output : 3431 KWm / 4767 KVA Voltage : 10500V Frequency : 50 Hz Qty : 8 sets Used gas generator, about 4000 hrs

Resato HBU-B160 Gas High Pressure Workshop Testing System The oil and gas industry is all about the extraction of crude oil and natural gas. One of the challenges is to make the best use of the assets to produce more from the available resources. Various high-pressure applications can contribute to this. Pressure tests guarantee the quality and safety of components for oil and gas production. By injecting a chemical liquid, the well is stimulated. With the controller, high-pressure systems control and regulate back pressure and liquids. In this way, oil and gas can be extracted more safely. Manufacturer: Resato HBU Test System  Type: HBU-B160 Max. pressure: 200bar Max. Capacity: 1570cc/ Max. pressure: 7 bar 2 x Gas Bottle Cage 3 x gas cylinder trolley Digital control panel is missing More items - new and used - can be found in our shop! International shipping costs on  ...

This industrial plant was built in 2007 as a pilot project and is only used temporarily. The complete package includes numerous pumps, pneumatic and manual gate valves of various sizes, as well as ball check valves, flow meters as well as the entire pipeline construction and a control cabinet. Preferably, this system is sold as a package including self-dismantling. Details on request.

From operating resolution: MIgatronic PI 250 DC Year of construction 2014 Pulse function HF Ignition Water cooling without function Welding Range: 5-250Amp 250Amps at 30% ED 180A at 60% 150A at 100% 220 volts with 8meter burner (sheathing partially damaged), ground cable and pressure reducer Dimensions in mm approx. 1100x630x720 --Very neat device-

ring cutting machine, cutting device, cutting pliers, cutting machine, ring, disc, segment and strip cutting machine, ring cutting machine -Manufacturer: Klinger, ring cutting machine -Cutting range: 80 - 1250 mm -Cutting thickness: up to 9 mm -Dimensions total 1100/170/H280 mm -Weight: 6.4 kg

From the stock of authorities: Pulse system little used Elmatech Hybrid 4002 Year of construction 2005 Welding capacity 400Ampere at 60% ED 320Amps at 100% Water cooling 4-Roll Wire Feeder Wire feeder case DV 39 with 5meter intermediate hose package 4meter burner with regulator Wire rolls 1.0-1.2mm + rolls for aluminum wire Dimensions in mm without case 1000x450x930 with operating instructions, pressure reducer and ground cable

From operating resolution: Selco Genesis 352 GSM DC Device No.007410000118 with water cooling Welding range 6-350 amps 350Amps at 60%ED 270Amps at 100% ED 380 volts with 8meter burner AQ 18F with flexible head and ground cable Adjustable pulse function RF Ignition 2/4 stroke

Plasma cutting machine, plasma cutter for plasma cutting system -Manufacturer: Hypertherm, gas console for plasma cutting machine -Type: 073239 from plasma cutting machine HT2000LHF -Dimensions: 295/175/H370 mm -Weight: 9.9 kg

Heat exchanger for inert gas welding machine, inert gas device, cooler -Manufacturer: CLOOS, heat exchanger from inert gas welding machine GLC 353 MC3 -Blower: ebm papst type M4Q0465-DA01-S8 -Dimensions: 330/160/H330 mm -Weight: 4.2 kg

gasoline engine, gas engine, drive engine -Manufacturer: Perkins, gas engine -Type: unfortunately without type designation -Engine power: -Dimensions: see photos -Transport dimensions: 800/670/H980 mm -Weight: 426 kg

From operating resolution: Pulse welding system Cebora EVO Speed Star 380 TC Specifications: Control Sound Digibox MIG P4 Welding range 10-380 amps 310Amps at 100% ED 4 Roller feed Water cooling TIG welding possible in the DC range Feed rollers 1.2mm Burner 4meter with 1.0mm wire, ground cable and pressure reducers-- Dimensions in mm approx. 950x850x1020 Operating instructions