g k used for sale

Compressor Pack Make: Grasso Model: 411 Year 2005 Freon Previously used for a 10 ton ice machine Does not include control panel

Used plastic agglomerator, model GHX 300. New: 2021. Technical data: - Capacity 300 liters, - Recommended feed 200 liters, - Efficiency 220 kg/h (PE / PP PET / PA films), - Automatic or manual water supply, - 75 KW engine, - Installed set of six sets of fixed knives, - Rotating arm with double-sided knives, - Knife material 9 CrSi, - Pneumatic agglomerate discharge with the possibility of setting in automatic or manual mode, - Good condition / Used for only one year.

Horizontal Plate Freezer Self contained with built in Gram Compressor Pack 6 station In cabinet Needs service/overhaul "AS IS"

turning diameter: max. 560 mm turning length: 600 mm control: 840D powerline Siemens greates pass round over bed: 680 mm Swing dia. over traverse guideway: 565 mm centre distance: 620 mm Main spindle:: turning speed range - main spindle: 20 - 5.000 min/-1 power capacity - main spindel: 25 / 37 kW max. Torque: 390 Nm spindle nose: 170H5 spindle bearing diameter: 120 mm usable bar diameter: 65 mm max. chucking diameter: 250 mm C-Axis: 0,025° / 360 ° Subspindel:: Spindle speed range subspindle: 20 - 7.000 min/-1 power capacity - Sub spindle: 25 / 33 kW max. Torque: 213 Nm spindle bearing diameter: 90 mm spindle bore: 57 mm spindle nose: 140H5 C-Axis: 0,025° / 360 ° turret:: number of toolpositions: 12 pos. Number of driven toolspositions: 12 pos. Spindle speed - driven tools: max. 4.500 min -1 power capacity - driven tools: 12,2 kW tool taper: VDI 40 DIN 69880 Tool dimensions with sq ...

E-chain hoist, electric hoist, crane GIS type 150 / FFabr. No: 1502802 Year of construction 1981Load capacity 1500 kgHook travel 4 metersMain lifting speed 4 m/min. Fine lifting speed 1 m/min.- Electric carriage with a speed for double T-beams- 2 load trainsGood condition; used

Max. drilling capacity steel and thread: 60mm, drilling speed: 56-1250/min, motor power: 5.5kW, height: 2400mm. The machine has been regularly serviced, without technical documentation, an on-site inspection is possible.

Fine boring head, spindle tool, boring head, bridge tool, fine boring headBoring tool, spindle headBoring tool, spindle headBoring rodReceptacle for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731 200Boring head for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731-010Boring block for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731-500Counterweight for bridge tool = SECO - epb GRAFLEX (Made in France) Type A731-600Tool holder: GRAFLEX Holder size G7 = 46 mmProcessing diameter: 200-280 mmAdjustment accuracy: 0.01

Drive motor, DC servo motor LENZE type GFQBT 80-24Spindle motor, electric motor, main spindle motorSeries No. 184592 Year of construction: 1993Nominal power: 4.2 kWook voltage: 260 V DCNoth current: 20 ampereMaximum speed: 3000 rpm. Excitation voltage: 200 V DCexcitation current: 1.15 ampere electric brakeShaft diameter: 24 mm (shaft with 8 mm key)Shaft length: approx. 47 mm (shaft protrusion from centering edge)Centering flange diameter: 110 mmBolt circle diameter: 130 mm, 8 x M8 threaded encoder, speedometer, GBR

Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/AMasch. No. 9566 Year of construction approx. 2000Punching force 80 ton. Projection 300 mmPunching up to 40 mm in 14 mm sheet metalFlat material shears 450 x 15 mmAngle steel shears 130 x 130 x 13 mm4 edge shears 45 x 45 mmRound material shears 45 mmRectangular clinker up to 12 mmMotor power 5.5 kWNeching connection 400 volts, 50 Hz stop with el. Stroke release 500 mm - work table with stop at the hole device 550 x 380

Swing diameter over bed/face slide: 570mm/420mm, turning diameter: 420mm, turning length: 635mm, traverse path X/Z: 220mm/635mm, speed: 5000rpm, spindle bore: 79mm, max. bar diameter: 65mm. Tool positions: 12, driven tools: 6, tool holder: VDI 30, rapid traverse X/Z: 24m/30m/min. Machine dimensions X/Y/Z: approx. 3500mm/2500mm/2000mm, weight: approx. 4500kg. On-site inspection is possible.

X-axis: 607mm, z-axis: 286mm, spindle speed: max. 6000/min, control: Fanuc 32i A, length: 4600mm, width: 1600mm, height: 2700mm, weight: 2.1t, operating hours: 34,536h. With automation FMB Unirobot LR MATE 200iD7L-P2TB, grinding spindle Jäger HF-Spindle, chuck MicroCentric 4-410-3-QC, MARPOSS measuring system with automated dimensional compensation, oil mist filter S400, belt filter Knoll KF110/500, hinged belt conveyor 320 S1 and other accessories. On-site inspection is possible.

Turning diameter: 200mm, turning length: 400mm, turning diameter: 420mm, bar diameter: 60mm, max. spindle chuck diameter: 160mm, speed: 5000rpm, turret: 2, positions: 2x14, rapid traverse X/Z: 20m/min/30m/min. Machine dimensions X/Y/Z: approx. 7500mm/2100mm/2100mm, weight: approx. 4500kg. Documentation available. On-site inspection is possible.

X-axis: 607mm, z-axis: 286mm, spindle speed: max. 6000/min, control: Fanuc 32i A, length: 1850mm, width: 1750mm, height: 1750mm, weight: 2.1t, operating hours: 14,841h. With FMB Unirobot GP7-5Pkhs automation system, Jäger HF spindle grinding spindle, MicroCentric 4-410-3-QC chuck, MARPOSS measuring system with automated dimensional compensation, S400 oil mist filter, Knoll KF110/500 belt filter, 320 S1 hinged belt conveyor and other accessories. On-site inspection is possible.

X-axis: 607mm, z-axis: 286mm, spindle speed: max. 6000/min, control: Fanuc 32i A, length: 1850mm, width: 1750mm, height: 1750mm, weight: 2.1t, operating hours: 59,861h. With automation FMB Unirobot MH5LS-SP, grinding spindle Jäger HF-Spindle, chuck MicroCentric 4-410-3-QC, MARPOSS measuring system with automated dimensional compensation, oil mist filter S400, Liqui gravity filter UR1020 with clean tank and other accessories. On-site inspection is possible.

Travel X/Z: 800mm/300mm, max. turning diameter: 320mm, max. turning length: 300mm, speed: 5000rpm, spindle power: 22kW, tool slots: 12, tool holder: VDI 40, main spindle clearance: 79mm. Machine dimensions X/Y/Z: approx. 5000mm/3900mm/2800mm, weight: approx. 6700kg, control: Siemens Sinumerik 840D, operating hours: 42996h. Documentation available. On-site inspection is possible.

Turning diameter: 200mm, passage diameter: 330mm, passage diameter over cross slide: 260mm, travel X/Z: 160mm/460mm, feed X/Z: 24m/min, speed: 5000rpm, spindle clearance: 51mm, spindle power: 16.5kW/11kW, torque: 1665.5Nm/112Nm, tailstock: 400mm, tool positions: 12. Machine dimensions X/Y/Z: approx. 4200mm/1700mm/2300mm, weight: approx. 3500kg, control: Siemens Sinumerik 810D. Including chip conveyor. Documentation available. On-site inspection is possible.

Travel X/Y/Z: 400mm/300mm/400mm, speed: 2000rpm, spindle mount: SK40, feed: 380mm/min, rapid traverse X/Y/Z: 1200mm/min, table dimensions X/Y: 320mm/750mm, quill stroke: 80mm, milling head tilt: +/-90°. Machine dimensions X/Y/Z: approx. 1800mm/1200mm/1200mm, weight: approx. 1300kg. On-site inspection is possible.

A 5-axis CNC milling machine Geiss with full encapsulation is available. Travel X/Y/Z: 2500mm/2200mm/760mm, tool holder: ER25, spindle power: 11kW, milling head type: orthogonal milling head, control: Siemens Sinumerik 840 Di solution line. Documentation available. On-site inspection is possible.

Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm.

Punching force: 110t, max. punching capacity: 40mm/20mm, throat depth: 750mm, stroke rate: 28/min, max. stroke: 80mm, working height: 1066mm, machine dimensions X/Y/Z: approx. 2300mm/1300mm/2300mm, weight: approx. 4000kg. An on-site inspection is possible.

Various machines and peripheral equipment for metalworking are available. 1) Troma TC 300. 2) Sigloch and Schrieder Boromat 14 4. 3) Glaser. 4) Renard DM1-R. On-site inspection is possible.

A complete bending line for the production of flange rings is available. Workpiece dimensions X/Y: 440mm/350mm, max. cross-section (S355 NL): 65000mm², max. flat steel length: 22000mm, max. outer ring diameter: 7000mm, max. inner ring diameter: 2320mm, max. ring weight: 11t. 1) Preheating furnace holes, machine dimensions X/Y/Z: approx. 1500mm/500mm/22000mm. 2) Faccin conveyor belt, length: 22000mm. 3) Ring bending machine Faccin Giotto 3000. 4) Flash butt welding machine Asdorfer HY 1500, power: 1500kVA. 5) Faccin handling system, max. ring diameter: 6500mm. Documentation available. On-site inspection is possible.

An HMS punching machine is available. Pressing force: 250t, stroke height: 40mm, installation height: 450mm, ram adjustment: 20mm, stroke rate: 120 strokes/min, overall system dimensions X/Y/Z: approx. 17000mm/8000mm/3500mm. Including coil and strip processing. Documentation available. On-site inspection is possible. Expected to be available from September 2025.

A Gutmann blasting system completely overhauled by Rösler in 2019 is available. Documentation available. On-site inspection is possible.

Three identical Gullco electrode ovens are available for drying and stabilizing welding electrodes. Internal dimensions X/Y/Z: approx. 350mm/400mm/480mm, max. electrode length: 450mm, max. temperature: 550°C, power consumption: 1.5kW, machine dimensions X/Y/Z: approx. 560mm/560mm/620mm, weight: approx. 160kg. Documentation available. On-site inspection is possible.

Saw blade diameter: 750mm, saw blade speed: 2200/min, table dimensions: 1500x1500x900mm, cutting height 90°/45°/30°: 295/200/137mm, motor power: 16kW, length: 1800mm, width: 1500mm, height: 1100mm, weight: 650kg. On-site inspection is possible.

Connected load: 4.55kW, cooling capacity: 9kW, circulation medium temperature: 30°C, refrigerant: R 134a, filling weight: 2.13kg, max. operating overpressure: 21bar, compressor volume flow: 11.46m³/h, compressor speed: 2900rpm, compressor discharge pressure: 22.6bar. Documentation available. On-site inspection is possible. The appliance was only used for a few hours for test purposes.

Max. pipe diameter: 500mm, power: 1.7kW, max. pipe thickness: 6mm, weight: approx. 4100kg. Documentation available. On-site inspection is possible.

A Graewe planetary saw (inline pipe saw) is available. Max. pipe diameter: 500mm, power: 7.5kW, machine dimensions X/Y/Z: approx. 3500mm/1800mm/2000mm, weight: approx. 3200kg. Documentation available. On-site inspection is possible.

GKS UP300 vertical bagging machine, Compact machine, easy to work width.

Équipement de distribution Schneider Merlin GERIN Masterpact circuit breaker. Batch of 17 circuit breakers avalable, possible to sell individually. Disjoncteur : M20N1 Circuit breaker 3 Piece Disjoncteur : M16N1 Circuit breaker 1 Piece Disjoncteur :M25N1 Circuit breaker 1 Piece Disjoncteur :M10N1 Circuit breaker 3 Piece Disjoncteur :NW12N1 Circuit breaker 3 Piece Disjoncteur :M32H1 Circuit breaker 2 Piece Disjoncteur SEL PACT DN 2 Circuit breaker 1 Piece Disjoncteur compact NS1250NA Circuit breaker 2 Piece Disjoncteur CM 1250 Circuit breaker 1 Piece

Eillert flume washer,, More information soon., Have a look at the photos and videos

GRECON finger jointing line Ultra 4, Manufacture year 2002, single side shaping machine, with turn table, min/max infeed length 150/1000 mm, max. outfeed length 6100 mm, with glue system, Consisting of:, - Finger jointing machine, - Transport belt, - Tilt- and turn device, - Chain feeder, - Heavy duty double roller feed unit, - Integrated cut of saw, - Conti press, type A-12-6100, - Tooling, With Mixon glue pump, type 2453H/1 (year 2021)

A Gildemeister CNC double-spindle turning and milling center including coolant system and chip conveyor is available. Turning diameter over bed: 640mm, machining diameter: 400mm, center distance: 1930mm, travel X/Z: 550mm/1585mm, travel Y: +/-110mm, B-axis: +/-120° (interpolating), C-axis: 360°. Main spindle: power: 36kW/45kW, speed: 4000rpm, torque: 600Nm-730Nm, bore: 107mm. Milling spindle: Speed: 12000rpm, power: 13.2kW/22kW, torque: 100Nm. Tool places: 60, carrier: turret 12-fold star SW 380, machine dimensions X/Y/Z: approx. 9300mm/4600mm/3100mm, weight: approx. 20000kg, control: Siemens Sinumerik 840D powerline. Documentation available. On-site inspection is possible.

weight: 200 kg : 931855500 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 2 turning diameter: max. 250 mm toll turrets: 2 x 12 control: Fanuc 16 T tool taper: HSK 63 : 04800000181 frequency: 50 Hz ampere: 168 A The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: GoodAire 1800 output: 1.800 cbm/Stunde weight of the machine ca.: 200 kg Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

taper MK: MK5 round table: ja weight of the machine ca.: 1.200 kg Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

workpiece diameter: 25-90 mm threading length: 3000 mm thread pitch: 2-16 mm total power requirement: 25 kW weight of the machine ca.: 10,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding length: 1000 mm grinding width: 500 mm workpiece height: 425 mm Control: total power requirement: 15 kW weight of the machine ca.: 4,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

workpiece diameter: 320 mm threading length: 570 mm thread pitch: 315 mm total power requirement: 17 kW weight of the machine ca.: 12 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding length: 800 mm grinding width: 500 mm workpiece height: 425 mm total power requirement: 15 kW weight of the machine ca.: 4,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

number of spindles: 4 bore capacity in steel (diameter): 23 mm bore stroke: 150 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 400 mm y-travel: 300 mm z-travel: 400 mm total power requirement: 3,6 kW weight of the machine ca.: 1,3 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

length: NA mm height: NA mm total power requirement: 5 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 42 mm turning length: 250 mm control: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m CNC-lathe with bar feed with Sameca bar feed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning speeds: 24000 U/min frequency: 0 Hz output: kw High Frequ. Grinding spindle, type: TSSV 150 - 15000/16, 16 kW,dia 150 x lgth 400,15.000rpm TSSV 150 - 15000/16, 16 kW,dia 150 x lgth 400,15.000rpm TSSV 150 - 24000/12, 12 kW,dia 150 x lgth 400,24.000rpm TSSV 150 - 24000/12, 12 kW,dia 150 x lgth 400,24.000rpm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

honing diameter: 12 mm stroke: 40 mm throat: mm total power requirement: 15 kW weight of the machine ca.: 5 t dimensions of the machine ca.: m 3 spindle honing machine with in process measuring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

honing diameter: 80 mm stroke: 280 mm throat: 300 mm total power requirement: 6 kW weight of the machine ca.: 2,6 t Honing Ø 10 - 100 mm Max. honing depth, approx. 250 mm Max. spindle stroke 260 mm Distance between spindle and column 300 mm Mounting height 1,000 mm Table size 350 x 500 mm Height of table above floor 500 mm Spindle speeds in 2 steps, infinitely variable, approx. 85 - 300 rpm 170 - 600 rpm Stroke speed, infinitely variable, hydraulic 0 - 23 m/min Spindle drive 2 kW Total electrical load 6 kW - 380 V - 50 Hz Weight 2,600 kg Accessories / Special Features Built-on 2-station tilting table which accommodates 2 workpieces. Mechanical workpiece clamping, using a manual lever. Hydraulic infeed of the tool. Switch-off via timer. Air measuring device (probably). Honing oil unit. Various splash shields, etc. Condition : Good. Machine can be in ...

turning diameter: 250 mm turning length: 400 mm control: C 200 / 8 total power requirement: 60 kW weight of the machine ca.: 8,5 t Swing Ø above bed, max. 300 mm Max. turning Ø for chucking work, approx. 250 mm Travel of Slides: Turret 1, X / Z travel 163 / 550 mm Turret 2, X / Z / Y travel 140 / 250 / 260 mm Spindle bore, approx. 65 mm Tool holder bore 30 mm Spindle speeds 25 - 5,000 rpm Feed range 0 - 15,000 rpm Spindle drive 0.5 - 40 kW Total electrical load 60 kW - 380 V - 50 Hz Weight, approx. 8,500 kg Accessories / Special Features SIEMENS CNC Continuous Path Control, Model 880 (INDEX C 200-8) for at least 6 axes, with enlarged memory and with subprograms, simulation, etc. Double column loading device for large workpieces, mounted above the machine. With 3-jaw gripper and storage system for blanks and finished parts, integrated in the CNC control. Spindle indexing an ...