four column press used for sale

1- one combination of lay-up, turning and unloading 2- BTF Multifoiler 3- Multi-Pin-System Useful area 1330x2630 mm Max size of board 1250x2550 mm Min foil width 1400 mm

Hot press Make: ORMA Type: NPC/DIGIT 6/95 New machine Technical datas: Press area: 3000x1300 mm Amount cylinder: 6 Lift & max. press opening: 400 mm Total pressure: 90t Electro-heater 18 kW for thermo-oil (120°C) Optional: - Aluminium coating for panels - 650 mm stroke - Parallelism control by sensor - Extra charge for down stroke design - 4 side loading - Max. temperature up to 150°C - Max. temperature up to 200°C - Mylar protection foil - Pressure plate covered with glass fier fabric Teflon - Hardware for Industry 4.0

Hot plate press (electric) Brand: ORMA Type: NPC 6/120 new machine Technical data: Heating plates: 3500x1300mm Cylinder: 6 pieces Press force: 120t Stroke/opening dimension: 450mm Connection value: 28.8kW (ELKOM plates) Options: - Intermediate plate - Anodized surface for ELKOM panels - Parallelism sensor á 1,000.00 EUR - Pressing mechanism from above (fixed lower plate) - Max. temperature till 150°C - Max. temperature till 200°C - 4-sided loading possible - Mylar protective film - Fiberglass Teflon protection - Hardware for Industry 4.0

Press capacity: 50 ton Ram stroke adjustable: 16 - 51 mm Slide adjustment: 64 mm Free frontal opening L-R: 1100 mm Free lateral opening F-B: 250 mm Table surface area : 1080 x 650 mm Slide area: 980 x 420 mm Hole in table: 1060 x 200 mm Number of strokes: 100 - 750 s.p.m. Required power: 22 kW Working hours machine: 16850 h Height over floor approx.: 2471 x 1278 x 3150 mm Weight of machine approx.: 9 ton

pressure: 80 t throat: 280 mm stroke: 10-100 mm no. of strokes: 52/80 Hub/min ram - range of adjustment: 60 mm table surface area: 850x550mm mm ram surface: 420x220 mm hole in the table: 300x200 mm table height: 780 mm tool hole in ram: Ø 45 mm weight of the machine ca.: 4,5 t dimensions of the machine ca.: 2000x2000x2700mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 28 t distance between columns: 510 mm dayligth: 380 mm stroke: 260 mm weight of the machine ca.: ca. 750 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press capacity: 315 ton Ram stroke adjustable: 30 - 100 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 370 mm Table surface area : 1600 x 1100 mm Slide area: 1600 x 1100 mm Hole in table: 600 x 180 mm Number of strokes: 15 - 180 s.p.m. Table height over floor: 1200 mm Required power: 170 kW Height over floor approx.: 4900 mm Dimensions L x W x H: 4900 x 1900 x 4900 mm Weight of machine approx.: 55 ton

Pressure total: 600 ton Ram stroke: 762 mm Slide adjustment: 406 mm Shut height (stroke down, adjustment up): 1322 mm Free frontal opening L-R: 3700 mm Table surface area : 3350 x 2134 mm Slide area: 3350 x 2134 mm Die cushion capacity in table: 180 ton Die cushion stroke: 305 mm Ejector in ram: 60 ton Ejector stroke in ram: 230 mm Number of strokes: 16 s.p.m. Required power: 90 kW Weight of machine approx.: 185 ton

Sales are made on behalf of the customer

SPECIFICATIONS: Briquettes: Ø 60 mm Production: 70 kg/h Installed power: 7.5 kW EQUIPMENT: 1 mini silo

Capacity: 160 ton Throat depth: 350 mm Ram stroke: 20 - 140 mm Slide adjustment: 75 mm Shut height (stroke down, adjustment up): 740 mm Table surface area : 1000 x 680 mm Slide area: 600 x 300 mm Number of strokes: 50 s.p.m. Required power: 15 kW Weight of machine approx.: 12 ton

with additional vacuum insert (sack)

110 Tons Press Machine 70-55 table size, 48-33 between colons with PLC Hydrolic

Press capacity: 160 ton Ram stroke adjustable: 20 - 130 mm Slide adjustment: 100 mm Daylight: 560 mm Table surface area : 1500 x 800 mm Slide area: 1400 x 800 mm Number of strokes: 20 - 60 s.p.m. Distance between the columns F - B: 520 mm Height over floor approx.: 3550 mm Required power: 48 kW Weight of machine approx.: 26 ton

​The PME 400-1700 C is a mechanical C-frame press manufactured by PME Pressen- und Maschinenbau Erfurt GmbH. While specific details about the 2018 model are limited, based on PMEs product offerings and industry standards, the following information outlines the typical features and specifications of this press model --------------------------------------------------------------- Key Specifications - Pressing Force: 400 kN (approximately 40 tons) - Table Width: 1,700 mm - Frame Type: C-frame (single-column) - Drive System: Mechanical eccentric drive via countershaft - Clutch-Brake System: Pneumatically or hydraulically operated combination - Ram Guidance: Precise sliding guide or roller recirculation guide - Stroke Adjustment: Fully automatic and electronically monitored - Ram Adjustment: Motorized - Overload Protection: Hydraulic system Find more here - .ucymachines/ Contact us at ...

Capacity: 250 - 400 ton V ? Ring nominal force: 20 - 200 ton Counter ram nominal force: 10 - 100 ton Ram stroke: 30 - 200 mm V-Ring stroke: 40 mm Counter ram stroke: 40 mm Daylight: 760 mm Ram surface: 800 x 800 mm Table surface: 810 x 1000 mm Max. die size: 765 x 760 x 610 mm Number of strokes: 40 s.p.m. Approach speed: 120 mm / sec Return speed: 135 mm / sec Working speed: 5 - 50 mm / sec Die Weight total: 2400 kg

SPECIFICATIONS: Installed power: 9.2 kW Briquette size: Ø 70 mm Complete with 13 filter bags (Ø 160 x 550 mm)

with 63 filling valves and 16 head crown corker 26 mm with double pre-evacuation system Work direction: from right to left Product: beer and other products with CO2 Capacity: approx. 25.000 bph - by 500 ml bottles approx. 30.000 bph - by 350 ml bottles More technical details you can see on the technical data sheet. Complete documentation, manual, spare part list, electrical documentation are available. The filler was in production in a Germany brewery and can be inspected on side.

pressure: 35 t chamfer lenght: 2000 mm weight of the machine ca.: 3 t total power requirement: kW distance between columns: mm dimensions of the machine ca.: m pressure 35to max. bending length 2000mm arrester behind drive capacity 4,5 kW weight 3000kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 25100 Specifications: - Pressure capacity 200 t - Working width 3050 mm - Passage between the uprights 2550 mm - Table width 180 mm - Projection 250 mm - Installation height 400 mm - Feed speed 80 mm/sec. - Working speed 6.7 mm/sec. - Retraction speed 67 mm/sec. - Plunger stroke 150 mm - Adjustment range fixed stops 120 mm - Drive 400 V 14.5 kW - Space requirement approx. W 3800 x H 2980 x D 1700 mm - Weight approx. 11500 kg - with: - Back gauge with 2 stop fingers - Deer's foot tool - 4-fold universal die - Two-hand control panel, foot switch,

Manufacturer: NEFF Model: 4SP 160 Year of Manufacture: 2011 Operating Hours: 25 aprox Type of Machine: Hydraulic Press Weight: 7000 kg Condition: Used Control System: Siemens S7 (PLC) Technical Specifications - Press Force: 1600 kN (adjustable from 160–1600 kN) - Return Force: Approx. 160 kN - Stroke (Hub): 500 mm - Table Size (W x D): 2000 x 800 mm - Ram Size (W x D): 2000 x 800 mm - Clear Height (Ram Up): 700 mm - Max. Daylight (Open Height): 2850 mm - Table Height Above Floor: 800 mm - Clearance Between Columns (W x D): 1600 x 410 mm - Installation Space (W x D x H): 2000 x 800 x 700 mm Electrical System - Operating Voltage: 400V AC - Control Voltage: 24V DC - Valve Voltage: 24V DC - Frequency: 50 Hz - Voltage Fluctuation Tolerance: ±5% - Max. Ambient Temp: 35°C Find more here - .ucymachines/ Contact us at - sales@ucymachines

CONTROLS   PLC SIEMENS S7 PRESS DESIGN   drive system: link drive   feedstock transport direction: left to right SLIDE   total force (nominal): 80 to   stroke: 50 mm   stroke rate (max.): 80 /min COUNTER RAM   nominal force: 22 to   stroke: 8 mm V-RING   nominal force: 25 to   stroke: 15 mm TOOL DIMENSIONS   lower table (left-right): 420 mm   lower table (front-back): 420 mm   upper table (left-right): 420 mm   upper table (front-back): 420 mm   shut height max.: 220 mm   ram adjustment: 80 mm   distance between columns (H-frame): 450 mm   passline opening (free passage in side columns): 200 mm OVERALL SPECIFICATIONS (COIL LINES)   sheet width max.: 180 mm   sheet thickness max.: 5 mm   feed velocity max.: 999 m/min STRIP-FEEDER   feeder type: roll feeder   sheet width max.: 180 mm   sheet thickness max.: 5 mm   feeding step max.: 999 m ...

Control SAFAN ... TS 1 Thrust... 50t Bending length ... 2550mm controlled axes ... 4 Drive... Electric Max. ram stroke ... 215mm Main engine power ... 9kW Machine weight ... 5050kg The machine is in good condition, possible to test under power.

Eccentric shaft by drawing K04.038.842-22-402 for hot stamping press K04.038.842 (K8542), 1600T brand new in state stale from stock W 4675 kg

-) Press surface: 3,100 x 1,600 mm -) Cylinder: 8 cylinders -) Floors: 5 floors, 6 heating plates -) Heating plates: drilled 40mm steel heating plates -) Heating: for hot water or thermal oil (up to 200° -) Press opening: up to 600 mm -) Cooling: with own unit Etc.

Brand Lisec Type Butyl extruder machine Model LBH-25ARS + 2x RAV2 Serial number 572-003937 Year of construction 2000 Weight 2.1ton Assets 7kVA Air pressure 6bar Water pressure: NVT Length +/- 11m Width +/- 5m Height +/- 3.5m Working height ,4m Transport dimensions L x W x H Special 2 pcs 3.5×2.6x2m + 6×1.5×3.2 Min.-max. profile 4-15mm Min.-max glass size 2.5×3 Number of brushes n/a Number of spindles n/a State machine n/a Type of control B&R Electrical connection 380+N+PE Instructions for use Yes Electrical diagram Yes Parts list available on request Available software back up Photos/film available: Photos and video available

Pressing and joint-setting machine Book height : 100 - 520 mm Book width : 120 - 450 mm Book thickness : 6.5 - 100 mm Output : approx. 150 books/hour (depending on the material used)

Pressure leaf filter for filtration of vegetable oil - 8m² filter area - 720 litres - Pneumatically operated swing flap at the outlet - Including piping with valves - With control cabinet - Optionally with screw compressor

FETTE Terminal, Data Control, Type 2080, Year 1989

FETTE Data Control 2, Installed in a mobile cabinet including an EPSON printer

Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007

Press capacity: 50 ton Ram stroke: 54 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 303 mm Table surface area : 810 x 550 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 7,5 ton Main Motor: 11 kW

Maplan 160ton Injection Machine Injection MTF 750/160 Platen size = 510mm x 450mm Stripper plate/ejectors =top only Max gap between platens = 575mm Volume = 750 ccm3 Tonnage = 160T Year 2002

A dismantled Mecamaq hydraulic press is available. Pressing force: 100t, max. pressure: 290bar, main piston diameter: 200mm/120mm, auxiliary cylinder diameter: 40mm/25mm. Main cylinder working stroke: 500mm, max. installation height: 800mm, working height: 800mm, effective dimensions X/Y: 700mm/500mm, table dimensions X/Y: 800mm/500mm, working speed: 6mm/s, return speed: 150mm/s. Max. tool dimensions X/Y: 800mm/600mm, max. tool weight: 1000kg. Machine dimensions X/Y/Z: approx. 1000mm/1350mm/2750mm, weight: approx. 4000kg. Documentation available. On-site inspection is possible.

Key data: 80 t, 400 mm, 112 mm

Printing capacity: 80 ton Table surface: 750 x 550 mm Plunger adjustment: 80 mm Stroke length: 8 - 112 mm Stroke rate: 78 p/min. Projection: 400 mm Equipped with: - Air coupling - Safety screen Country of origin: Germany Motor power: Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight approx.: 7000 kg

Key data: 300 t, 4300 mm, 3700 mm

Printing capacity: 300 ton Bending length: 4,300 mm Stand width: 3,700 mm Back gauge: 550 mm Stroke length: 300 mm Projection: 450 mm Feed speed: 120 mm/sec. Working speed: 10 mm/sec. Retraction speed: 120 mm/sec. Control: Delem DA65 Equipped with: - Y1, Y2, X&R - Axis Controlled - CNC hydraulic crowning - Various sets of bending tools - Safety light cabinet Lazer Safe - Operating instructions and machine documents Country of origin: Netherlands Motor power: 30 kW Machine LxWxH: 510 x 200 x 330 cm Machine weight: 21,500 kg

HYDRAULIC PRESS with hot platens model ITALPRESSE SCF 6 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton. 120 opening mm. 400 hydraulic pump motor power Hp 3 hot water plates heating via wood boiler weight kgs. 4500 volt. 380/50

! Exhibition Machine Corresponds to the Panhans LLB116 with the following optional accessories: - Single-lever operation with fine locking - Dial gauge in the handwheel for height adjustment SPECIFICATIONS: - Max. drilling depth 145 mm - Max. elongated hole length 240 mm - Height adjustment 135 mm - Motor power 1.3/1.7 kW - Suction nozzle Ø 100 mm - Machine weight 200 kg

! Exhibition Machine Equipment/Technical Data Work table mm 800x400 Motor kW 1.5/1.9 kW Spindle speed rpm 1440 / 2880 Max. slotted hole height above the table mm 160 Max. longitudinal work run mm 345 Max. transverse work run mm 245 Spindle stroke mm 160 Clamping Ø of tool mm 0 - 20 Max. tool length mm 175 Span Center Piece 2 Rotating table ° +/- 45° Dimensions of the machine mm 1500x1100x950 Machine weight kg 345 Other features: - Mechanical dowel device, distance 16-22-25-32 - Mechanically numerical spindle height display - Suction nozzle

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Key data: 50 t, 1600 mm, 200 mm

CNC Press Brake COLLY 502/A Numerical Command: CYBELEC type DNC 32 P-CM Capacity: Maxi length 2000 mm x 50 T Throat depth: 200 mm Distance between uprights: 1600 mm Back Gear Gauge 1 axe Defective cylinder Right cylinder joint to change Machine functional (only right cylinder joint to change) Voltage: 380 V Length: 2500 mm Depth: 2100 mm Total height: 2400 mm Weight: approx 4 T

Vertical Multistage High Pressure Centrifugal Pump KSBTyp Movichrom N CN 3/10 2RFabr. Nr 1-P30-837561Nominal flow rate max. 3 m3/hNominal delivery head 70 meters = 7 barNominal speed 2900 rpm. Motor power 1.5 kWNet connection 400 volts, 50 Hz- pump structure in 10 stages- pump elements made of stainless steel, pump base made of cast iron connection flanges DN 32- suitable for drinking water supply, irrigation and drainageSpace requirement pump L x W x H 250 x 220 x 830 mmWeight 38 kgUnused replacement pump made of

Courtoy Compressor, Type R292F, Type D, 55 positions, Year 1999, Missing the 2 compressed descent and the cables between electrical cabinet and machine;, All the documentation including the electrical diagrams is present (in French), Punch type: D, Weight (kg): 4500 , Cadence / hour: 43 000 - 350 000, Compression (kN): 100, Precompression (kN): 10, Maximum tablet dimensions (mm): 25,40, Outer diameter of die (mm): 38,10, Matrix height (mm): 23,81, Punch diameter (mm): 25,40, Die outer diameter (mm): 38,10

pressure: 40 t table length: 670 mm table width: 570 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press capacity: 100 ton Ram stroke: 300 mm Slide adjustment: 125 mm Shut height (stroke down, adjustment up): 600 mm Free frontal opening L-R: 2.020 mm Free lateral opening F-B: 620 mm Table surface area : 2.000 x 1.000 mm Slide area: 2.000 x 900 mm Hole in table: 1.700 x 300 mm Number of strokes: 10 - 50 s.p.m. Table height over floor: 1.200 mm Required power: 39 kW Height over floor approx.: 4.400 mm Dimensions L x W x H: 5.166 x 2.500 x 4.400 mm Weight of machine approx.: 38 ton

Capacity: 60 ton Throat depth: 275 mm Ram stroke: 5 -100 mm Shut height (stroke down, adjustment up): 375 mm Table surface area : 740 x 470 mm Number of strokes: 14 - 100 s.p.m. Required power: 10 kW Dimensions L x W x H: 2.300 x 1.500 x 3.000 mm Weight of machine approx.: 3,5 ton

Press capacity: 40 ton Ram stroke adjustable: 8 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 310 mm Free frontal opening L-R: 820 mm Table surface area : 810 x 450 mm Slide area: 720 x 350 mm Hole in table: 600 x 110 mm Number of strokes: 100 - 1.000 s.p.m. Table height over floor: 1.030 mm Required power: 19,5 kW Weight of machine approx.: 6,8 ton

Capacity: 25 ton Throat depth: 250 mm Ram stroke: 6 - 60 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 190 mm Height of the bolster plate: 50 mm Table surface area : 500 x 400 mm Slide area: 350 x 250 mm Tool Clamping Hole Ram: 40 H7 mm Number of strokes: 160 s.p.m. Dimensions L x W x H: 1.300 x 1.500 x 1.995 mm Weight of machine approx.: 2 ton

Press capacity: 30 ton Throat depth: 160 Ram stroke adjustable: 20 - 45 mm Slide adjustment: 10 / 60 mm Shut height (stroke down, adjustment up): 220 mm Table surface area : 470 x 300 mm Slide area: 250 x 190 mm Number of strokes: 80 - 240 s.p.m. Required power: 4 kW Dimensions L x W x H: 1.400 x 1.800 x 2.000 mm Weight of machine approx.: 2,67 ton

Press capacity: 40 ton Ram stroke adjustable: 8 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 290 mm Free frontal opening L-R: 600 mm Free lateral opening F-B: 190 mm Table surface area : 600 x 500 mm Slide area: 600 x 400 mm Hole in table: 500 x 110 mm Number of strokes: 65 - 400 s.p.m. Table height over floor: 1100 mm Required power: 32 kW Height over floor approx.: 2.800 mm Weight of machine approx.: 6,2 ton