forklift side lift used for sale

Side broom Kärcher 6.905-624.0 Dimensions: 450 x 450 x 150 mm Weight: 1 kg

Single-stage side channel pump, oil pump, coolant pump LUKRA PUMPS, LUTZ KRACHT SS13 flow rate: 20 l/min motor : 0.25 kW 220 - 250 / 380 - 440 V IP 44 used, tested ! Dimensions: 210 x 150 x 230 mm

Sell Fenwick S30W diesel sideloader, 3 Ton capacity, telescopic forks, maximum height 5.3 meters, 3021 hours, Up-to-date revisions. Video on Demand

Machine foot set with side orientation, wedge feet, levelling shoe PAGUS support height: 84 - 90 mm side orientation: 10 mm support surface: 170 x 110 mm weight: 14.25 kg 2 pieces each Dimensions: 260 x 165 x 125 mm

Key data: 7 , 230 mm, 160 mm

SPECIFICATIONS: Maximum processing height: 160 mm Maximum machining width: 230 mm Length of inlet planer: 2100 mm Spindle diameter: 40 mm Number of Spindles: 7 (6 + 1 Universal) Grid table Shaft drive (3.7 kW) Self-braking motors Voltage: 380 V Spindle configuration: 1ST: BOTTOM (5.5 kW) 2ND: RIGHT (5.5 kW) 3.: LEFT movable (5.5 kW) 4TH: RIGHT (5.5 kW) 5TH: TOP (7.5 kW) 6TH: BOTTOM (7.5 kW) 7TH: UNIVERSAL SPINDLE 360° (7.5 kW)

PART NUMBER: 7503 SPECIFICATIONS: - max planing width 610mm - max planing height on both sides 200mm - max planing height on four sides 100mm in advance: - 2 rubber pull rollers - 2 toothed pulling rollers - metal pulling roller - Pulling insertion shaft, toothed -Triggers -Pressure - pulling shaft, toothed 2 pcs -Pressure - planer shaft 610mm, 4-knife 7.5kW -Pressure - Pulling roller, smooth, metal -Pressure - profiling roller 7.5kW -Pressure - rubber pulling roller From below: - scoring unit, axle 35mm, axle length 130mm 2.2kW - guide strip 2 pcs - Introductory table top - Pulling shaft, smooth - planer shaft 610mm, 4-knife (2 knives installed) 7.5kW - 2 pulling shafts, smooth - Split metal skid roller - side pressure behind: - Side spindles + clamps 2 - 1) vertical right 95mm 4kW - 2) vertical left 95mm 4kW - spindle diameter 35mm - spindles adjust ...

used side feeder for foil snippets / scrap Centrifuge with drive and feed container this unit was mounted on a 150 mm extruder Capacity over 320 kg/h

Elmo G 200 Side Channel Compressor 8.5kW 2915rpm Unused Replacement Machine Weight approx. 180kg The cover on the engine at the rear is missing. unused replacement device. Was in stock, in case the first machine should fail. From insolvency

Manufacturer: HolzHer, Type: 1444, Year: 1991, Min-max feed m/min: 10 - 20, Premilling: yes, Coil magazine: yes, Strip magazin: no, Mitre stations: yes, Bevel milling: yes, Corner tracing type: no, Top pressure belt/roller: Rolle, Year :1991

Heavy Duty Four-Sided Combined Calibration Milling Planer with Additional Scoring Saw for Relief Grooves Detailed technical description in the PDF document (as an attachment in the photo gallery).

This shredder has a large diameter rotor (30 cm) and 12 rotating blades. The motor has an output of 4 kW. This shredder is equipped with a torque increase gear (reducing gear), so it is also suitable for shredding thicker plastic waste. The grid is interchangeable, so the grain size can be changed. Everything works fine, motor, bearings, gearbox, rotor, blade are all fine. It can be used immediately. I have several of them. Other shredders are also for sale. Please see my other ads.

Weinig Profiamt 22N four-sided planer Working width 230mmm Working height 120mm Number of spindles 5 1.Bottom 4kw 2.Rights 3.Left 5.5kw 4.Top 5.5kw 5.Universal 4kw Pneumatic material clamps Feed speed adjustable via variator 6-22m/min Feed motor 2.2kw Automatic worktop lubrication Worktop air cushion Length of the material insertion table 1970mm

Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.

Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l

Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton

Pressure total: 500 ton Stroke: 1100 mm Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton

Manufacturer: KDP Kantenanleimmaschine, Type: KDP 111 SL, Year: 1995, Min-max edge material mm: 0,5-2,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: 8, Lasertechnik: yes, Mitre stations: yes, Radius milling axis adjustment: no, Year :1995

Manufacturer: IMA Steckprofileindrückmaschine, Type: Nowimat/I/G80/500, Year: 2001, Control: Ima, Work piece width min-max mm: ca.60, Min.-max. workpiece length in mm: 2500, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: ca.20, automatischer Einzug: yes, Premilling: 4 X 2,2 kw, Coil magazine: 2 Stück Stegprofil, Mitre stations: yes, radius milling: Eindrückstation Profil, Work piece refeeding: yes, Hover cussion table: yes, Hover cussion table: yes, Year :2001

Manufacturer: Weinig, Type: H 17 AS, Year: 1986, Planing widht mm: 230, Number of spindles: 9, Tool exchange places: yes, Separate engine per spindle: yes, Feeding - kW: 11, Feeding speed min-max m/min: 60, Feeding speed continous adjustable: yes, Table length: ca. 4000 mm, 1.Bottom spindle kW: 4, 2nd spindle on right kW: 4, 3.Left spindle kW: 5,5, 4th spindle on right kW: 4, 5.Top spindle kW: 7,5, 6th spindle at bottom kW: 5,5, 8th spindle at bottom kW: 7, 8th spindle on left kW: 4, 10th universal on left kW: 5,5, FREE TEXT: Inverter for feeding., Year :1986

Manufacturer: Sicar, Type: P5N/230, Year: 1989, Control: yes, Planing widht mm: 230, Planing hight mm: ca.130, Number of spindles: 5, Rotations of spindles max. rpm: 6000, Separate engine per spindle: yes, Feeding - kW: 1,5, 1.Bottom spindle kW: 5,5, 2nd spindle on right kW: 5,5, 3.Left spindle kW: 5,5, 4.Top spindle kW: 7,5, 7th universal on left kW: 5,5, Year :1989

Manufacturer: IMA, Type: Man.Kantenanleimer HKA, Min-max edge material mm: 0,4-3, Work piece width min-max mm: 100, Min.-max. workpiece length in mm: 100, Edgeband height max mm: 16-45, Min-max feed m/min: 0,7-1,2,

Manufacturer: IMA, Type: Advantage 8200, Year: 2003, Min-max edge material mm: 0,4-20, Work piece width min-max mm: min. 60, Min.-max. workpiece length in mm: min. 150, Min.-max. workpiece height in mm: 10-60, Min-max feed m/min: 4-20, Premilling: yes, Mitre stations: yes, Radius scraper: yes, Flat scraper: yes, Profile sanding top bottom: yes, Weight approx. kg: 4400, Year :2003

Manufacturer: Homag, Type: KLO 76, Year: 1994, Min-max edge material mm: 0,5-3,0, Min.-max. workpiece length in mm: 150, Edgeband height max mm: 55, Min-max feed m/min: 10-25, Premilling: no, IR zone: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, radius milling: yes, 4 motors: yes, Radius scraper: yes, Flat scraper: yes, 4 motors: yes, Ersatzverleimteil : yes, Bonding part EVA: yes, Pre-smelting Kg/Hr: yes, Buffing unit: yes, Top pressure belt/roller: yes, Roller/belt: Riemen, Compressed air bar: 6, Machine lenght mm: 7500, Noise enclosure: yes, Year :1994

Manufacturer: IMA, Type: Man.Kantenanleimer HKA, Min-max edge material mm: 0,4-3, Work piece width min-max mm: 100, Min.-max. workpiece length in mm: 100, Edgeband height max mm: 16-45, Min-max feed m/min: 0,7-1,2,

Manufacturer: Weinig, Type: Unimat 17, Planing widht mm: 170, Planing hight mm: 120, Spindle diameter in mm: 35, Rotations of spindles max. rpm: 6.000, Spindle arrangement: U / R / L / R / O / U, Feeding - kW: 4, 1.Bottom spindle kW: 4, 3.Left spindle kW: 3, 4th spindle on right kW: 3, 5.Top spindle kW: 4, 6th spindle at bottom kW: 4,

Manufacturer: Ott, Type: F 2530, Year: 2008, Min-max edge material mm: 0,2-25, Work piece width min-max mm: min. 65, Min.-max. workpiece length in mm: min. 150, Min.-max. workpiece height in mm: 8-60, Min-max feed m/min: 10-16, Premilling: yes, Mitre stations: yes, 2 motors: yes, Type of scraper: Profil und flatch, Flat scraper: yes, Year :2008

Manufacturer: Weinig, Type: Unimat 17, Planing widht mm: 180, Planing hight mm: 120, Number of spindles: 7, Elektronische Achsverstellung: no, Work piece width min-max mm: 180, Min.-max. workpiece length in mm: 350, Wellendrehzahl: 6000, Spindles: 6, Spindle diameter in mm: ca 40, Spindle arrangement: U / R / L /R / O / U / Uni, 1.Bottom spindle kW: 4, 2nd spindle on right kW: 4, 3.Left spindle kW: 4, 4th spindle on right kW: 4, 5.Top spindle kW: 4, 6th spindle at bottom kW: 4, 7th universal on left kW: 4,

Manufacturer: Ilcam Kantenbearbeitung, Year: ca.1990, Monting of the machine: Verleimteil/Kappen/Vorfräsen/Zieklinge, Min-max edge material mm: 0,5-12, Work piece width min-max mm: 65, Min.-max. workpiece height in mm: 10-55, Min-max feed m/min: 10-20, Premilling: no, Fine milling: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Radius scraper: yes, Year :ca.1990

Manufacturer: Brandt , Type: KD 79/2 CF, Year: 2002, Min-max edge material mm: 0,5-3,0, Min-max feed m/min: 18, Axis control: no, Premilling: yes, Fine milling: yes, Application of separation agent: no, IR zone: no, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, 2 motors: yes, Radius scraper: yes, Flat scraper: yes, Bonding part EVA: yes, Buffing unit: yes, Top pressure belt/roller: Rolle, Work piece refeeding: yes, Year :2002

Manufacturer: IMA, Type: Man.Kantenanleimer HKA, Year: 2000, Min-max edge material mm: 0,4-3, Work piece width min-max mm: 100, Min.-max. workpiece length in mm: 100, Edgeband height max mm: 16-45, Min-max feed m/min: 0,7-1,2, Year :2000

Manufacturer: Felder, Type: MG 580-1, Year: 2012, Control: yes, Min-max edge material mm: 0,4-5, Work piece width min-max mm: min. 70, Min.-max. workpiece length in mm: min. 140, Min.-max. workpiece height in mm: 8-60, Min-max feed m/min: 11, Premilling: yes, Mitre stations: yes, Weight approx. kg: 990, Year :2012

Manufacturer: SCM, Type: P64, Year: 1988, Planing widht mm: 180, Planing hight mm: 105, Number of spindles: 4, Rotations of spindles max. rpm: 6000, Separate engine per spindle: no, Main engine kW: 4, Fully suspended drive feeding: yes, Feeding - kW: 2,5, Feeding speed continous adjustable: yes, Tischlänge mm: 2000, Adjustment - electonically: no, Noise enclosure: yes, Compressed air bar: yes, Wight approx. kg: 2000, Year :1988

Manufacturer: IMA, Type: Compact F 12, Year: 1996, Control: Beckhoff, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 65, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-50, Min-max feed m/min: 18, Infeed table: yes, Premilling: yes, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Corner tracing type: yes, 4 motors: yes, 4 motors: yes, Bonding part EVA: yes, Pre-smelting Kg/Hr: yes, Year :1996

Manufacturer: Homag, Type: FKR 78/C/A/S3, Monting of the machine: zerspanerteil zum Einkürzen, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 250, Min.-max. workpiece height in mm: 10-40, Min-max feed m/min: ca.18, Infeed table: yes, Premilling: yes, Fine milling: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Radius scraper: yes, Flat scraper: yes, Bonding part EVA: yes, Work piece refeeding: Bargstedt, Roller/belt: Riemen, Compressed air bar: 6, Return type: Bargstedt TFU,

Manufacturer: Homag , Type: KAL 310/8/A20/S2, Year: 2005, Control: PC 22, Work piece width min-max mm: min 55/100, Min.-max. workpiece height in mm: 12 - 60, Min-max feed m/min: 18 - 24, Einlauflineal gesteuert: yes, Premilling: 2 x 3kW, Application of separation agent: yes, Coil magazine: 2, Mitre stations: Fase / Gerade, Pre-milling: 2 x 1,5 kW, Bevel milling: FK 13 - 8Fach, radius milling: 4 kW, Corner tracing type: MN 21, Flat scraper: FA 11, Bonding part EVA: A 20, Top pressure belt/roller: Band, Work piece refeeding: vorinstalliert, FREE TEXT: Frreiplatz, Year :2005

Manufacturer: Hebrock, Type: AKV 2001 DK, Year: 1997, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-45, Min-max feed m/min: 8, Coil magazine: yes, Strip magazin: no, Mitre stations: yes, Pre-milling: Radius, Corner tracing type: yes, 1 motor: yes, Radius scraper: yes, Bonding part EVA: yes, FREE TEXT: Zustand sehr gut, Year :1997

Manufacturer: Brandt, Type: KS 23, Year: 1988, Min-max edge material mm: 0,5-12, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-50, Edgeband height max mm: 55, Min-max feed m/min: 12, Premilling: no, Coil magazine: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Bevel milling: yes, Corner tracing type: no, Radius scraper: yes, Flat scraper: yes, Bonding part EVA: yes, Edge sanding: yes, Year :1988

Auction-ID: A1-40282-51

Manufacturer: IMA, Type: Quadromat 4012 F, Year: 1995, Program: yes, Min-max edge material mm: 0,5 - 8,0, Min.-max. workpiece length in mm: 250, Min-max feed m/min: 10, Premilling: yes, Min.-max. batten magazine mm: 0,5 - 8,0, Mitre stations: yes, radius milling: yes, Corner tracing type: yes, 2 Motoren: yes, Year :1995

Manufacturer: Brandt, Type: KD 99, Year: 1998, Control: Homatic, Min-max edge material mm: 0,4 - 3,0, Work piece width min-max mm: 62, Min.-max. workpiece length in mm: 160, Min.-max. workpiece height in mm: 60, Edgeband height max mm: 62, Premilling: yes, Bevel milling: yes, Corner tracing type: yes, 4 Motoren: yes, Nuten : yes, Radius scraper: yes, 4 Motoren: yes, Compressed air bar: 6, Machine lenght mm: 8740, Noise enclosure: yes, Rückführung Typ: yes, machine ready for demonstration: yes, Year :1998

Manufacturer: Brandt , Type: KS 25, Year: 1991, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 10-50, Edgeband height max mm: 55, Min-max feed m/min: 14, Premilling: no, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Flat scraper: yes, Bonding part EVA: yes, Top pressure belt/roller: Rolle, Werkstückunterstützung: yes, Freiplätze: keine, Year :1991

Manufacturer: Ziwo, Type: CL 11.10, Year: 1996, Work piece width min-max mm: 0 - 300, Min.-max. workpiece length in mm: 200, Min.-max. workpiece height in mm: 5 - 150, Wight approx. kg: 210, FREE TEXT: Beschickung, Year :1996

Manufacturer: Weinig , Type: Unimat 17 A, Year: 1979, Control: hand, Planing widht mm: 10-170, Planing hight mm: 10-120, Min.-max. workpiece length in mm: 300, Number of spindles: 6, Diameter of the spindle mm: 30, Fast exchange device: no, Rotations of spindles max. rpm: 6000, Separate engine per spindle: yes, Fully suspended drive feeding: no, Year :1979

Manufacturer: Koch, Type: SBD - 320 , Year: 1994, Control: Programm, Working widht max mm: 1500, Arbeitstiefe max mm: 320, Working thickness max mm: 10 - 32, Saw diameter mm: 350, Work piece transport: Kette, Drilling support horizontal: 2, Drill gearings: 7, Drill gearings: 7, Drill support from top: 5, Drill gearings: 7, Belt conveyor: yes, Gluing: yes, Re-charging: no, Dovel insertion: yes, Raster 32 mm: yes, Horizontal drilling from both sides: yes, Wight approx. kg: 6000, Year :1994

Manufacturer: Biesse , Type: Stream B1 S3, Year: 2005, Control: NC 1600, Min-max edge material mm: 20, Work piece width min-max mm: 65, Min.-max. workpiece length in mm: 150, Min.-max. workpiece height in mm: 60, Min-max feed m/min: 25, Min.-max. batten magazine mm: 20, Bevel milling: yes, radius milling: yes, Radius scraper: yes, Buffing unit: yes, Year :2005

Manufacturer: Ott, Type: Euromatic FÜ, Year: 2001, Program: yes, Control: SPS, Work piece width min-max mm: 60 , Min.-max. workpiece length in mm: 60, Min.-max. workpiece height in mm: 10 - 60, Kantenmaterial min-max mm: 0,2 - 15, Vorschub min- max m/min: 12 - 20, Mitre stations: yes, Fasefräsen: yes, Flat scraper: yes, Rolle/Riemen: Rollen, Machine lenght mm: 8500, Wight approx. kg: 4200, Year :2001

Manufacturer: Lange Kantenfräsgerät, Type: B 600, Year: 2009, Moulding spindles: 2, Routing: yes, Min.-max. workpiece length in mm: 8-60, Vorschub min- max m/min: Handvorschub, Mitre stations: yes, Mitre stations: yes, Radiusfräsen : 1,5 mm, FREE TEXT: Fräsmotore Frequenzgeregelt, Year :2009

Manufacturer: HolzHer, Type: 1411-1, Year: 2001, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 230, Edgeband height max mm: 50, Thickness of coiled edgeband max mm: 3, Vorschub min- max m/min: 11, Glue system granulate/cartridge: Patrone, Buffing unit: yes, Machine lenght mm: ca. 4.100, Wight approx. kg: ca. 1.100, Year :2001

Manufacturer: HolzHer, Type: Sprint 1310, Year: 2006, Edgeband height max mm: 45, Thickness of coiled edgeband max mm: 3, Vorschub min- max m/min: 10, Mitre stations: yes, Glue system granulate/cartridge: Patrone, Mitre stations: yes, Radiusfräsen : yes, Buffing unit: yes, Top pressure belt/roller: rolle, Compressed air bar: 6, Machine lenght mm: 3, Year :2006

Number of boring spindles: 8 St. Working width: 20 - 230 mm Working height: 8 - 120 mm Length of the planing table: 2.500 mm Feed motor: 4 kW Feed speed: 5 - 24 m/min. total power requirement: ca. 60 kw Dimensions (L/W/H): mm weight of the machine ca.: kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.