We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,440 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
18 transport pallets for concrete walls or similar and 1 pallet lifter
used
Lifting tipper Kemper HK 200 LD for San Cassiano boiler - Kemper HK 200 LD lifting tipper - for San Cassiano boiler - with boiler cutter - Year of construction 2004
used
Vacuum lifting device for paper rolls NAGRON AEROLIFT Vacuum lifter for the paper industry Woudenberg Holland Type R96-20 Fabr. No. 9745 Year of construction 1999 Payload 2000 kg Centering mandrel 90 mm Suction surface Outer diameter 850 mm (plus seal)Suction surface inner diameter 250 mm (minus seal) Seal width 50 mm Suction surface 0.5 m2 Negative pressure min. -800 mbar Pumping speed approx. 100 m³/h per vacuum pump Motor power 2x 2.2 kW Mains connection 400 Volt, 50 Hz - 2 pieces Rietschle vacuum compressor, type VCE 100 Dimensions x H 1600 x 2250 mm Height with centering mandrel 2500 mm Total height in transport frame 2950 mm Net weight 2,5 ton.; used
used
Hydraulic scissor lift table GRUSE type HF 2 HS Fabr. Product no.: 75432 Year of construction 2008 Load capacity 250 kg Platform size 1190 x 740 mm Useful stroke max. 1270 mm Construction height - table bottom 285 mm Construction height - table top approx. 1555 mm Operating pressure max. 150 bar at 250 kg engine power 0.75 kW mains connection 230 volts, 50 Hz - Rotary switch for up and down on the hydraulic unit - Double shears with a lifting cylinder- Pipe rupture protection directly on the cylinder - circumferential safety contact strip with limit switches under the upper ramen - adjustable limit switch for the stroke restriction - hydraulic unit with tank separately standing own weight table unit approx. 180 kg net weight hydraulic unit approx. 30 kg good condition; used
used
Hydr. Scissor lift table TREPEL - L. A. VAN EIJLE & Co. Year of construction approx. 1980 Load capacity approx. 5 ton. Platform size 1700 x 1100 mm Stroke max. 515 mm Construction height Table bottom with rail castors 535 mm Height Table bottom without rail castors 480 mm Table height raised with rail rollers max. 1050 mm Table height raised without rail rollers max. 995 mm Travel speed Rail chassis approx. 8.5 meters/min. Motor power 4 kW Mains connection 400 Volt, 50 Hz - Manual switch for up and down on the cable - Safety limit switch - Hydraulics with tank mounted in the underframe- Lifting shears with two lifting cylinders - The table was movable on rails, 4 rollers on the base, 200 mm - Drive of the rail rollers via SEW Gear motor with chain Space requirement L x W x H 2070 x 1350 x 1050 mm net weight approx. 1.3 ton. good condition; used
used
Vacuum lifting device, vacuum lifter Custom-made as handling device for an industrial robot Year of construction 2008 Payload approx. 60 kg Suction foot spacing min. 120 x 150 mm Suction foot distance max. 700 x 600 mm- 4 pieces Suction feet 100 mm- 4 pieces Vacuum ejectors, vacuum generator PIAB with compressed air connection 8 mm - 2 pieces Cross member, adjustable in width via servo drive from 150-600 mm- Suction foot distance adjustable via 2 servo drives from 120-700 mm - Suction cup adjustment via 3 servomotors REXROTH MSK040C-0600-NN-M1-UP0-NNNN- Very complex and precise design with linear guides and trapetz threaded spindles- Flange plate for suspension or flanging on the robot Length: 105 cm, width: 66 cm, height: 54 cm Net weight approx. 120 kg good condition ; used
used
Stacker truck, walker, manual pedestrian stacker LOGITRANS type LF 1001 / 1600 Tool lifter series No: 051E04006100 Year of construction 2005 Load capacity: 1000 kg Lifting height: 1600 mm Fork length: 600 mm Platform size: 800 x 650 mm Total length: 1200 mm Total width: 800 mm Construction height: 1930 mm- Lifting by pumping movement with the traction dike- 2 lifting speeds approx. 36 strokes up to lifting height 1600 mm or approx. 10 strokes for 10 cm lifting height. - Driving by pushing hand fork stroke in single mast with free lift net weight 198 kg very good condition; used
used
Hydr. Scissor lift table WEIDMANN type E5/13-1 Fabr. No. 30403339 Year of construction 1982 / 2007 Load capacity 500 kg Platform size 2000 x 1200 mm Stroke max. 1280 mm Construction height - table bottom 290 mm Construction height - table top max. 1570 mm Table height with safety support 1430 mm Lifting speed 1280 mm in 25 sec. Lowering speed 1280 mm in approx. 0 to 15 sec. Hydraulic operating pressure approx. 130 bar Motor power 1.5 kW Mains connection 400 Volt, 50 Hz. - Rotary switch switch on the hydraulic unit for up and down - lowering speed infinitely adjustable via throttle valve- 1 lifting cylinder hydraulic unit year of construction 2007 with tank adjacent - safety protection frame with limit switches net weight 660 kg good condition; used
used
Hydraulic scissor lift table HYWEMA type SHT / IN Fabr. No. 52-22330 Year of construction 1996 / 2022 Technically overhauled in 2022 load capacity 4 ton. Platform size 2300 x 1200 mm Stroke max. 1420 mm Construction height - table bottom 400 mm Construction height - table top max. 1820 mm Table height with safety support 1565 mm Lifting speed 1420 mm in 30 sec. Lowering speed 1420 mm in 45 sec. Motor power 4 kW Mains connection 400 Volt, 50 Hz - Hand switch for up and down on the cable - Circumferential safety edge for lowering shutdown - Hydraulics with tank mounted in the underframe- 1 piece lifting shears with two lifting cylinders - Steel plate mounted on the lifting frame 1200 x 1200 mm x thickness 20 mm Space requirement L x W x H 2300 x 1330 x 400 mm Net weight 1.4 ton. good condition; used
used
Hydr. Hacksaw, metal saw, lifting saw KASTO type PSB WBS 210 / 230 Masch. No. 115 106 1212 / 72783 Year of construction 1986 Saw area - round 250 mm Saw area - square 225 x 225 mm Saw area - rectangle 260 x 100 mm Cutting speed 11 -13 - 17 - 22 - 26 - 34 m/min. Saw blade length 400 mm Motor power 1.4 and 1.8 kW pole switchable Mains connection 380 Volt, 50 Hz - only for 90 cuts, no miter adjustment- Saw motor with 2 speeds and 3 V-belt steps - Hydraulic saw bracket feeding - Hydraulic cutting pressure adjustment via throttle valve - Rapid traverse for saw bracket lower - manually via handwheel height-adjustable material support table with mm scale - manual material tension - Coolant device in the machine foot - Operating instructions Space requirement L x W x H 1500 x 700 x 1550 mm Weight 590 kg very good condition; used
used
Freight lift according to MRL ConVer 147.01 with instructed accompanying person. Payload 1.200kg. 2 stops 0-4117mm. Car size 2800x2860x2000mm. Colour framework RAL 7043 Rest RAL 7035. Access bottom front top front and rear. Price without assembly, TÜV and freight, pure only the machine. The machine can also be adjusted on request, e.g. conveying height. Here, the selling price would then have to be determined.
used
Hydraulic scissor lift table GRUSE type ELS 0.5-8-1-G-SO Fabr. Product code: 124984 Year of construction 2017 Load capacity 300 kg Platform size 1250 x 800 mm Useful stroke max. 785 mm Height - table bottom 345 mm Construction height - table top 1130 mm Motor power 0.8 kW Mains connection 400 volts, 50 Hz - Foot switch for up and down, with emergency stop and key switch for control Single scissors with a lifting cylinder - circumferential safety contact strip with limit switches under the upper ramen - adjustable limit switch for the upper lifting restriction - table surface with sturdy wooden worktop and airliner rails with lashing eyes - hydraulic unit with tank mounted under the table- feet under the table corners, mobile with pallet truck own weight 430 kg very good condition, almost as new; used
used
Foil lifting device, details see pictures, immediately available
used
Lifting kneader lifting kneading machine Kemper F30 SL -Manufacturer: Emil Kemper GmbH -Model: F 30 SL -with stainless steel boiler and lifting arm -with automatic timer -2 speeds -with flour dust cover -mobile on wheels -with new timer
used
Lift-tilt device, lifting tipper Make Itec, type 2700, year of construction 2017 for accommodating 200- and 300-litre standard loading trolleys lifting capacity: 350 kg Tipping height: 2.231mm incl. 1 standard loading trolley 3x460V 50 Hz 0,75 kW - very good condition, hardly used - was used to feed a piston filling machine - Documentation/operating instructions available Visit in Korntal-Münchingen possible
used
Used lifting kneader DIOSNA, type: S 35 -In bakery condition- - for 35 kg dough - with timer -Dust cover - Machine runs smoothly - technically tested and cleaned - very nice condition Inspection and test run are of course possible by arrangement.
used
Lifting tipper Kemper HK 200 L for President Kessel -Lifting tipper from Kemper Emil Kemper GmbH -Type: HK 200 L -for Kemper President 125 A boiler -Year of construction August 2007 -tipping height approx. 260cm -Total height 345cm -400V 50Hz 3Ph
used
Electric pallet trucks SPECIFICATIONS: Drive: electric Drive system support Load capacity kg: 1000 Lifting height mm: 1600 Fork length mm: 1200
used
Traverse 3 meters Stroke: 350 KG
used
Demag Traverse Total length: 5.5 meters Gauge: 5.0 Meter Stroke: 250 KG
used
Used lifting kneader DIOSNA, type: S 20 3G -In bakery condition- - for 20 kg dough - 3 gears - Machine runs very smoothly - very nice condition Inspection and test run are of course possible by arrangement.
used
: Staplerhebebühne lifting capacity: 6600 kg weight of the machine ca.: 2,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Machine Mechanics & electrics prepared by an expert cleaned & functionally tested Advantages: + Stainless steel boiler + Lifting arm was freshly nickel-plated + with flour dust cap, with automatic switch-off when lifting + Lifting kneader for particularly dough-friendly kneading processes + with drilling devices for anchoring in the ground Specifications: - Flour capacity: max. 75 kg - Dough capacity: max. 120 kg - Boiler volume: approx. 180 litres - Motor power: 8 kW - Power loads: 380V - 3Ph - 50Hz - Fuse: 16A CEE plug
used
Lifting kneader lifting swaging machine Diosna D 200 Plus A used lifting kneader Diosna D 200 Plus is currently for sale and immediately available in our warehouse in Bielefeld. Lifting kneader Diosna D 200 Plus with fixed Kesel - with stainless steel boiler - Kettle for maximum 200 kg dough or for max. 125 kg flour - 2 speeds slow and fast - with flour dust cover - mobile on wheels - Machine completely repainted - with stainless steel control box - with 1 timer NEW - many parts renewed - Boiler polished - 380 volts
used
- Lifting kneader Diosna S 35 - with stainless steel boiler - for max. 35 kg dough - with 2 speeds - with foot switch - with flour dust cover - Boiler diameter inside: 52cm - Inside boiler height: 35cm
used
Lifting tipper König HK1100/2400 for Diosna boiler - Lifting tipper king - Type: HK 1100 / 2400 - for Diosna boiler - with boiler drive - with boiler cutter - Year of construction: 2009
used
Lifting swaging machine Diosna S 120 Plus A used dough kneader Diosna S 120 for a maximum of 120kg dough, with 2 speeds, slow and fast is for sale and immediately available in our warehouse. Kneader Diosna S 120 - with 1 automatic timer - Machine is revised and repainted - with 2 gears - with stainless steel boiler - with flour dust cover - mobile on wheels with lock
used
Lifting tipper Diosna HK 300 for spiral mixer boiler - Lifting tipper from Diosna - Type: HK 300 - For W240 A spiral mixer boiler - with pliers lock - with boiler drive - movable on wheels, with brakes - Built in 2006
used
Boiler Lifting Tipper Kemper HK 200 R - Boiler tipper Kemper - Model: HK 200 R - for Kemper 150 AL boiler - with boiler drive and boiler shearer - Built in 2005 - Total height 312cm
used
BAUMANN paper lift Model NUP 1000 Year of construction 2003 Pile lifter with platform Load capacity: 1000 kg Lifting height: 1000mm Platform size: 1350 x 990 mm
used
Kemper Lifting Tipper Type: HK 150 Specifications: suitable for Kemper boilers SP 150 A and AL Load capacity: 1000kg Dumping height: 160cm Dimensions of lifting tipper: Height; 200cm Width: 100cm Depth: 160cm
new
Lifting capacity: 100 Kg Magnetic field: 70 x 60 mm weight: 5 Kg dimensions: 100 x 120 x 120 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
lifting capacity 1000 kg MeAssure 93 x 138 cm
used
Lifting mixer Kemper F 125 ASL extendable - with 2 speeds - with 2 automatic timers - with stainless steel lifting arm - max. 125kg flour or 200kg dough per kettle - with flour dust cover - Boiler with handle
used
Lifting kneading machine Diosna Capacity: 120 kg dough With protective grille 2 speeds via foot pedal Condition: Repaired
used
ATLAS scissor lift table, lifting capacity 4 t TECHNICAL PARAMETERS: German production table size 3000 x 1200 mm lifting capacity 4000 kg height of the unfolded table 1195 mm height of the folded table 450 mm pump motor power 4 kW table weight 1500 kg
used
electric scissor lift truck / manual Lifting height 800 mm Load capacity 1000 Kg at lifting height 600 mm / 800 Kg at lifting height 800 mm Weight 168 kg Battery 65 Ah / 12 V ( not available ! )
used
Vacuum lifters, vacuum lifters from Schmalz for heavy plates, sheets, etc. Load capacity 300kg horizontally and vertically Vacuum cleaner can be swivelled 90 degrees by motor 10 suction cups 370 x 85mm, suction cups partially removable Minimum dimensions of the suction cups: 1250 x 760mm Maximum size of the suction cups: 1900 x 1200mm Acoustic warning signal when the vacuum is too low 400V, 0,37kW Vacuum pump approx.8m³/h Pressure gauge to indicate negative pressure Can be attached to on-site chain hoist Swivelling and snap-in control lever, which means that parts can also be stacked very high With crane bottle holder CE mark No test book available Paint bursts reworked The machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration in our warehouse, see "other offers from this supplier".
used
Meyma Lift Tipper Type: HK 600 Specifications: for Diosna W 240 A spiral mixer boiler Dumping height: 170cm Load capacity: 600kg 400V 50Hz on castors Dimensions of lifting tipper: Height; 135cm Width: 130cm Depth: 190cm (with the safety bar)
used
carrying capacity: 2800 kg number of suction cups: 3 Stück total power requirement: 0,55 / 0,75 kW weight of the machine ca.: ca. 300 kg. New price ~ 11.000 euros Special price on request Furnishing: - Suspension frame with suspension eye for hanging in a hoist hook - Manipulating handle with easy-to-grip manual slide valve - main traverse (length: 2000 mm) - Dimensions suction plates .. 2x 720x720 mm .. 1x 615x615 mm - sliding suction plates - BECKER vacuum pump Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9803043 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Long goods box lifter, box lifter, crane traverse -Manufacturer: Scheffer Krantechnik -Payload: max. 1500 kg -Arm length: 750 mm -Box size: 3000x1000 mm -Own weight: 620 kg
used
hydraulic power pack / lifting unit VEB MASCHIENEN- U. GERÄTEBAU BRANDENBURG for pallet truck 121 Brieletta Year: 1983 220 / 380 V Engine: 2,,2 kW IP54 with hydraulic cylinder ORSTA B1 - 50 x 70 / 0 W TGL 21551 load capacity 1000 kp Pn 16 Mpa hub: 700 mm length: 900 mm used, tested ! Dimensions: 540 x 470 x 990 mm
used
Lifting magnet, permanent lifting magnet PAGUS magnetic area: 280 x 165 mm used, tested ! Dimensions: 320 x 165 x 340 mm
used
Control for lifting magnet WALKER HAGOU VR 10 ( VR10 ) for lifting magnet type EPR 570 x 402 Mains voltage: 400 V AC 50 / 60 Hz Output current: 300 A Control cable: approx. 2,7 m power cable: approx. 5.5 m connection cable: approx. 3.8 m control box: 400 x 300 x 200 mm used, tested ! Dimensions ( packaging ): 450 x 320 x 300 mm
used
Level lifter, lift table, pallet lifting device ZPRB pallet lifting device load capacity: 1200 kg lifting fork 1800 mm long, flush width: 800 mm stroke: approx. 850 mm height retracted: approx. 290 mm height extended approx. 1040 mm spindle stroke 380 V mobile by 4 rollers, 2 steerable ! used, tested ! Dimensions: 2500 x 1100 x 1750 mm (retracted)
used
Vakuumheber SCHMALZ VACUMASTER COIL VMCOIL 1000-90-25D Year: 2008 Load capacity 1000 kg diameter approx. 1300 mm For handling e.g. of coils and slit strips Suction plate 90° infinitely swivelling 380 V used, tested ! Dimensions 1800 x 1300 x 1600 mm
used
Lifting tower Lift MFI LAM a stroke: approx. 1900 mm used, tested ! Dimensions: 1700 x 1600 x 2800 mm
used
Lifting device, mobile PAGUS load capacity: 90 kg Lifting body: 460 x 300 mm, 85 mm deep stroke: approx. 500 mm height retracted: approx. 200 mm height extended approx. 700 mm Material: stainless steel hand winch: Type TANGO W V 500 Rope diameter: Ø 5 mm mobile due to 4 lockable swivel castors ! used, tested ! Dimensions: 1350 x 900 x 670 mm
used
Lifting tower - Lift MFI LAM stroke: approx. 2300 mm used, tested ! Dimensions: 1700 x 1600 x 2800 mm
used
belt lift table, lifting platform, scissor lift table, working platform PROHUB HEBETECHNIK Type 2013.00558 Year: 2013 Load capacity: 1700 kg Working surface: 5600 x 1220 mm retracted height: 320 mm maximum stroke: 1020 mm Main engine: SEW K87 DRE132M4BE11HR/ABE8/TF 5,5 kW 26 rpm 230 V 3AC with catch cylinder ! used, tested ! Dimensions ( transport ): 5600 x 1335 x 420 mm