138,027 used machines on RESALE, but how to find them? Machine Search
Pressing and joint-setting machine Book height : 100 - 520 mm Book width : 120 - 450 mm Book thickness : 6.5 - 100 mm Output : approx. 150 books/hour (depending on the material used)
Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007
FETTE Terminal, Data Control, Type 2080, Year 1989
Maplan 160ton Injection Machine Injection MTF 750/160 Platen size = 510mm x 450mm Stripper plate/ejectors =top only Max gap between platens = 575mm Volume = 750 ccm3 Tonnage = 160T Year 2002
FETTE Data Control 2, Installed in a mobile cabinet including an EPSON printer
Key data: 80 t, 400 mm, 112 mm
Printing capacity: 80 ton Table surface: 750 x 550 mm Plunger adjustment: 80 mm Stroke length: 8 - 112 mm Stroke rate: 78 p/min. Projection: 400 mm Equipped with: - Air coupling - Safety screen Country of origin: Germany Motor power: Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight approx.: 7000 kg
pressure: 40 t table length: 670 mm table width: 570 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
HYDRAULIC PRESS with hot platens model ITALPRESSE SCF 6 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton. 120 opening mm. 400 hydraulic pump motor power Hp 3 hot water plates heating via wood boiler weight kgs. 4500 volt. 380/50
pressure: 8,5 kN stroke: 40 mm throat: 95 mm Working height from to: 95 - 240 mm table surface area: 160 x 110 mm spindle diameter: 25 mm weight of the machine ca.: 27 Kg dimensions: 160 x 230 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
! Exhibition Machine Corresponds to the Panhans LLB116 with the following optional accessories: - Single-lever operation with fine locking - Dial gauge in the handwheel for height adjustment SPECIFICATIONS: - Max. drilling depth 145 mm - Max. elongated hole length 240 mm - Height adjustment 135 mm - Motor power 1.3/1.7 kW - Suction nozzle Ø 100 mm - Machine weight 200 kg
! Exhibition Machine Equipment/Technical Data Work table mm 800x400 Motor kW 1.5/1.9 kW Spindle speed rpm 1440 / 2880 Max. slotted hole height above the table mm 160 Max. longitudinal work run mm 345 Max. transverse work run mm 245 Spindle stroke mm 160 Clamping Ø of tool mm 0 - 20 Max. tool length mm 175 Span Center Piece 2 Rotating table ° +/- 45° Dimensions of the machine mm 1500x1100x950 Machine weight kg 345 Other features: - Mechanical dowel device, distance 16-22-25-32 - Mechanically numerical spindle height display - Suction nozzle
Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.
Courtoy Compressor, Type R292F, Type D, 55 positions, Year 1999, Missing the 2 compressed descent and the cables between electrical cabinet and machine;, All the documentation including the electrical diagrams is present (in French), Punch type: D, Weight (kg): 4500 , Cadence / hour: 43 000 - 350 000, Compression (kN): 100, Precompression (kN): 10, Maximum tablet dimensions (mm): 25,40, Outer diameter of die (mm): 38,10, Matrix height (mm): 23,81, Punch diameter (mm): 25,40, Die outer diameter (mm): 38,10
pressure: 8,0 kN stroke: 40 mm throat: 90 mm Working height from to: 50 - 200 mm table surface area: 120 x 160 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x410 mm Knee lever hand press with fine height adjustment SPECIAL PRICE! • Working height adjustable by simply loosening the clamping screws on the stand • Working height fine adjustment for HK 800 = adjustment of the press head to the desired working height. The fine adjustment takes place forced in both directions via a threaded spindle • Hand lever arranged in a user-friendly manner, return via spring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 4,5 kN stroke: 40 mm throat: 95 mm Working height from to: 95 - 240 mm table surface area: 160 x 110 mm spindle diameter: 25 mm weight of the machine ca.: 24 Kg dimensions: 160 x 230 mm Direct-acting pneumatic presses bring the full pressure performance over the entire stroke length. You will above all used when long-stroke parts are machined with constant force Need to become. Convincing technology • Long and precise spindle guide for maximum dimensional accuracy • Hardened and ground piston rod for practically unlimited service life • Double-acting cylinders with end position cushioning on both sides • Double guide rings in the piston, constant and quiet running • Oil resistant sealing elements Special features of the PND series • Spindle secured against twisting • Spindle return on the PND 85/S only via a cylinder chamber additional air savings • Easy, ...
pressure: 2,5 kN stroke: 45 mm throat: 90 mm Working height from to: 80 - 220 mm table surface area: 120 x 60 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x 390 mm Hand presses with rack HZ 250 The power is transmitted via a rack and pinion construction. she finds their use where during the working process a constant pressure is needed. Precisely manufactured, spindle hardened and ground, unlimited service life Long spindle guide, optimal pressure performance, T-slot according to DIN 650 milled in the middle, sliding blocks fit exactly. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 500 kN stroke: 40 mm throat: 73 mm Working height from to: 60 - 150 mm table surface area: 115 x 70 mm weight of the machine ca.: 10 Kg .Toggle lever hand press SPECIAL OFFER! • Working height adjustable by simply loosening the clamping screws on the stand • Working height fine adjustment for HK 800 = adjustment of the press head to the desired working height. The fine adjustment takes place forced in both directions via a threaded spindle • Hand lever arranged in a user-friendly manner, return via spring The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 200 t stroke: 400 mm daylight longitudinal/sideways: 1300 /450 mm dayligth: 900 mm tank capacity: 75 l liter capacity: 22 l feed down: 6,9 mm/sec feed up: 12,6 mm/sec Motor output: 7,5 kW weight of the machine ca.: 2,1 t dimensions of the machine ca.: 2,0 x 0,75 x 2,8 m Presses can be operated both by hand and by motor. Cylinders can be moved sideways. Safety valve with cylinder end position. CE marking 2 year guarantee The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 20 t stroke: 180 mm daylight between the columns: 540 x 100 mm dayligth: max. 990 mm : 72 mm diameter of piston: 48 mm weight of the machine ca.: 0,12 t dimensions of the machine ca.: 0,8 x 0,7 x 1,8 m Our frame presses are officially CE certified according to the latest rules. Almost all presses offered in this area are not CE certified. - with manual hydraulics - Move the cylinder sideways - Pressure gauge - 2 press documents The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 t stroke: 180 mm daylight between the columns: 335 x 115 mm dayligth: max. 340 mm : 56 mm diameter of piston: 40 mm weight of the machine ca.: 0,05 t dimensions of the machine ca.: 0,75 x 0,53 x 1,6 m Our frame presses are officially CE certified according to the latest rules. Almost all presses offered in this area are not CE certified. - with manual hydraulics - Move the cylinder sideways - Pressure gauge - 2 press documents The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 26,0 kN stroke: 60 mm throat: 110 mm Working height from to: 70 - 250 mm table surface area: 190 x 140 mm spindle diameter: 30 mm weight of the machine ca.: 46 Kg dimensions: 310 x 140 x 475 mm Knee lever hand presses SPECIAL PRICE! HK 2600 stroke 60 mm, incl. working height fine adjustment via bevel gear with comfortable and easy to adjust with a side crank. Stand height 475 mm Even more pressure in production without additional effort. Maximum pressure performance shortly before the end of the stroke thanks to toggle lever technology. Particularly stable construction of the spindle head and column The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 34,0 kN stroke: 40 mm throat: 130 mm Working height from to: 80 - 240 mm table surface area: 190 x 140 mm spindle diameter: 30 mm weight of the machine ca.: 80 Kg dimensions: 375 x 200 mm Toggle pneumatic presses incl. working height fine adjustment via bevel gear with lateral crank comfortable and easily adjustable. Toggle lever pneumatic presses are to be used when the maximum pressure is required shortly before the end of the stroke, e.g. when assembling, punching, embossing, caulking, etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 80 t stroke: 400 mm table surface area: 920 x 540 mm Motor output: 2,2 kW liter capacity: 9,0 l dayligth: 800 mm tank capacity: 31 l daylight between the columns: 920 x 300 mm weight of the machine ca.: 0,725 t dimensions of the machine ca.: 1,45 x 0,85 x 2,45 m Hand and Motor operated. Side-sliding cylinder. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 t stroke: 200 mm table-size: 450 x 450 mm working speed:: 10 mm/ sec. work height max.: 940 mm toolpiece height max.: 150 mm total power requirement: 1,1 kW : 150 x 6 mm weight: 0,4 t dimensions: 1,15 x 0,5 x 0,9 mm Horizontal bending machine with: - NC control - Dual footswitch - Set of standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: - t throat: - mm stroke: - mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 8437 Type: 50-VE Producer: IMS Created: 2002 Parameters: Compressive force: 50 t Maximum stroke rate per minute: 145 1/min Stroke: 80 mm Adjusting the ram: 75 mm Machine weight: 2300 kg
Container Press SMC/CP 1100 Used Equipment Used device is kpt. reconditioned, wear parts were replaced, incl. oil change and new hydraulic hoses incl. UVV safety test and protocol, 6 months warranty Pressing force: 3.5 tons Swivel stroke: 95 degrees Connected load: 230 V/ 1.5 KW Machine dimensions: 980x 1190x 1900 mm WxDxH Machine weight: 250 kg
Inv. Num. : 8438 Type: AF-200-75 Producer: Arisa Generated: Parameters: Maximum retraction speed: 200 t Top table length: 950 mm Top table width: 750 mm Maximum number of strokes: 20 1/min Ram stroke: 250 mm
nominal power: 63 t stroke rate in continuous stroke: 90 min force: 2200 Nm Torque: 12500 Nm Labour performance: 5,5 kW sheet thickness - max.: 6,3 / 3,2 mm cutting surface: 1600 mm² distance between columns: 320 mm throat: 315 mm min. ram stroke: 8 mm max. ram stroke: 120 mm ram adjustment: 70 mm ram surface: 400 x 500 mm tool hole in ram: 40 mm tool shank hole (depth x diameter): 92 mm T-slots: 2 Stk total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
FOR SALE: BRUDERER BSTA 50USL High-Speed Stamping Press With Automatic Strip Feeder BBV 190 500 kN | 100–1120 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 500 kN Stroke rate: 100–1120 strokes per minute Working hours: 41000 h Main motor: 22 kW Control voltage: 24V DC Power connection: 400V / 50Hz / 62 kVA Adjustable stroke: 16 / 19 / 25 / 32 / 38 /44 / 51 mm Shut height adjustment: 64 mm Working Dimensions: Max tool installation width: 1100 mm Strip pass width: up to 256 mm Ram area: 980 × 420 mm Table area: 1080 × 650 mm Strip entry height adjustable: 60–140 mm Max strip width: 120 mm Max feeding pitch: 85 mm Max material thickness: 4 mm Feeding angle: 180 Deg Machine Dimensions (with BBV 190): Machine footprint (L × W × H): 2407 × 1278 × 3150 mm Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 1 ...
Gluing press Emmes Type: H EBP 500 . 10 Working length 5000 mm Working height 1530 mm Support width or depth 150 mm 10 Hydraulic Vertical Press Punch 5 pneumatic front hold-down devices max. compressive force 150/cm² Hydraulic pump 2.2 kW Oil pressure 159 kg/cm Air pressure 8 kg/cm²
Used piston press for apple juice production made by Bucher, model: HP 5000, capacity 5 t / h. New: 1985. 2 pieces available for general renovation (hydraulics) or for parts. Control cabinet available for 1 press.
punching pressure: ca. 3,2 t air pressure: 8 bar stroke: max. 20 mm distance between columns: ca. 250 x 200 mm weight of the machine ca.: 52 kg incl. various tools, see pictures The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Qty. 1 Second-hand aluminium extrusion press line Code Aluminium HE9 6063 Mfc.: Indian manufacturer Built: 1978 PLC hydraulic – upgradation done in the year 2005! Total Force of Press: 680 MT, 750 UST Extrusion Pressure: 210 Bar Billet Diameter: 5”, 121 mm Weight per Inch of Billet: 0.76 kg/inch Scope of supply: Log heating furnace Hot shear Extrusion press Overhead puller Under-bed cooling system Run-out cooling bed Belt conveyor Stretcher Cutting machine Die oven Conveyor table Conveyor for final packaging
Pressure power: 6-8 bar Air consumption: 8 l/Hub height of stroke: 12 mm : 134 mm no. of strokes: 400 Hub/min punching force max.: 3500 kp weight of the machine ca.: 80 kg Schüco pneumatic press for Schüco punching tools Art. No. Schüco: 290 124 manual included various pressing tools included! tool nr. 283073, 280162,299259,283492, 283072, 282867, 282644, 282663, 282868, 283071, 283072 2 quick-release levers for secure and quick fastening of the press tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25227 Specifications: - Pressure capacity 150 t - Working width 3600 mm - Passage between the uprights 3150 mm - Table width 180 mm - Projection 250 mm - Installation height 325 mm - Feed speed 70 mm/sec. - Working speed 7 mm/sec. - Retraction speed 60 mm/sec. - Ram stroke 120 mm - Adjustment range fixed stops 120 mm - Motor power approx. 7.5 kW - Oil filling approx. 300 l - Space requirement approx. W 3850 x H 2300 x D 1600 mm - Weight approx. 8700 kg - with: - Swivel arm – control panel with ATL 550 control - For crimping depth + backgauge -Mot. Backgauge - Crowning device - Lasersafe FIESSLER - 4-fold universal die, split sharpening tool + deer's foot tool - Two-hand control panel, foot switch,
Offer 25200 Specifications: - Pressure capacity 200 t - Working width 3100 mm - Passage between the uprights 2600 mm - Table width 180 mm - Projection 300 mm - Installation height 450 mm - Feed speed 80 mm/sec. - Working speed 9 mm/sec. - Retraction speed 60 mm/sec. - Ram stroke 120 mm - Adjustment range fixed stops 120 mm - Drive 400 V / 18.7 kW - Space requirement approx. W 3300 x H 2950 x D 1900 mm - Weight approx. 10500 kg - with: - Adjustment of the crimping depth + baling pressure -Mot. Backgauge with handwheel fine adjustment - 4-fold universal die - sharpening tool - Two-hand control panel, foot switch,
SPECIFICATIONS: Working width: 3000 mm Working height: 2500 mm 4 push-button plate suspension handles TS/500 Interface 4 safety light barriers Installed power: 3 kW
High: 2.050 mm, Long: 750 mm, Force: 10 tons, Width: 600 mm, Weight: 800 Kg., Neckline: 150 mm, Stem travel: 200 mm, Rate of climb: 10 cm / sec, Piston rod ø of: 65 mm, Surface of the table: 300 x 300 mm., Specification: Hydraulics
pressure capacity max.: 80 t Stroke: 500 mm table surface area: 960 x 810 mm spindle pitch: 72 daylight between the columns: 950 / 540 mm passage: 640 mm machine weight ab.: 4500 kg dimensions of the machine ca.: 2,0 x 2,0 x 3,85 m Hydraulic quick adjustment 500mm Flywheel Ø2000mm 4 prism bases for straightening waves different support frames The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Equipment Description Used Indirect Extrusion Press • Brand / Model: SMS Hasenclever 28 / 31.5 MN McKechinstrang” • Type: Horizontal indirect extrusion system for non-ferrous billets • Drive: Mechanical main unit with hydraulic auxiliaries • Country of Origin: Germany • Current Status: Dismantled and available for dispatch • Serial No. / Year of Manufacture: [To be confirmed] 2. Key Technical Specifications Parameter Value Main Piston Force 25.07 MN Total Press Force with Coupling 31.23 MN Max Stroke 3,070 mm Working Stroke 2,825 mm Ram Speed at 28 MN 0–64 mm/sec Ram Speed at 31.5 MN 0–57 mm/sec Billet Diameter Range Ø 230–355 mm Billet Length (cold) 320–1,320 mm Receiver Heating System Resistance; max 63 kW / 375 °C Shear Force 0.64 MN Profile Ejector Force 0.31 MN Actuation Differential Cylinders Ø 280/200 3. Included Components • B ...
used baler Herateller: PAAL Type: PACOMAT II Year of Make: 1995 Specifications: Pressing force: 27 t Drive power: 18.5 kW Total connected load: 25 kW Throughput: 115 m³/h Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm (H x W)
automatic baler Manufacturer: PAAL Type: Pacomat IS Year of Make: 1990 specifications: Pressing force: 27 t Specific pressing force: 5.51 kg/cm² Total connected load: 23 kW Rated current: 46 A Main drive power: 18.5 kW Capacity: 80 m³/h Control: Siemens S5 100 U Bale size: 700 x 700 Filling opening: 800 x 600 mm
automatic baler Manufacturer: PAAL Type: KONTI 125 SO Year of Make: 1990 specifications: Press force: 40 t Specific pressing force: 5.7 kg/cm² Channel format: 700 x 1,000 mm Bale weight: 375 - 450 kg, depending on material and bale length Filling opening: 1,400 x 920 mm Machine weight: approx. 10 t Drive power: 22 kW Throughput: 115 m³/h Pressing capacity: approx. 4.00 t/h at department store (35 kg/m³ bulk weight) approx. 6.75 t/h for mixed paper (60 kg/m³ bulk weight) approx. 10.0 t/h for collected goods (100 kg/m³ bulk weight)
Inv. Num. : 8499 Type: PEKRS 160 Producer: IWK Created: 1970 Parameters: Table length: 2000 mm Table width: 1000 mm Maximum stroke rate per minute: 55 1/min Stroke: 8-180 mm Adjusting the ram: 110 mm
Birth Smoking Machine Specifications: Table size600 x 320 mm Borehole depth205 mm Drill hole length250 mm Height adjustment165 mm Engine speed 2840 rpm Weight180 kg
used 2-way baler Manufacturer: MBH BRONNEBERG Type: SUPER II Operating hours: 1,575 h specifications: Press forces: Lid: 900 kN Intermediate compressor: 900 kN End compressor: 120 kN Package dimensions (h x w): 305 x 305 mm Filling opening (l x w): 1,600 x 1,000 mm Drive power of the main pump: (37 kW ? to be tested) Performance data: Sheet metal waste: up to 3 – 5 mm. Cycle time: approx. 45 - 60 sec. Number of parcels: up to 40 - 50 / hour Dimensions: Length: 4,200 mm Width: 1,900 mm / 3600 mm Height: 2,400 mm Weight approx. : 10 tons Subject to errors in the technical data
used tested briquetting press New components in the electrical box V400/50 Diameter briquette 50 mm Capacity approx. 50 kg/h
maximum number of results exceeded
please refine your search
