138,533 used machines on RESALE, but how to find them? Machine Search
Hydraulic Press Brake SAGITA BEYELER 200/4000 Slide travel: 150 mm Throat depth: 300 mm Distance between uprights: 3100 mm Motor power: 15 kW Manual Back gear gauge The machine was only used for pre-bending of Hardox sheet Voltage: 380 V Dimensions (L x W x H): 4100 x 1800 x 2700 mm Weight: approx 15 T
clamping force: 250 kN injection volume: 134 cm³ screw diameter: 35 mm platen size: 300 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 250 kN - Heating plate dimensions: 300 x 300 mm - Heating power of the plates: 5.3 kW - Clamping/opening stroke: 330 mm - Platen distance with heating plates at maximum: 380 mm - Clamping direction: from below - Side ejector: yes - Stroke of side hydraulic ejector: 100 mm - Ejector stroke/force: 70 mm / 24 kN Injection unit: - Increased injection pressure: 1,580 bar - Maximum injection volume: 134 cm³ - Screw diameter: 35 mm - Screw length: 17.1D - Maximum screw speed: 20–480 rpm - Metering stroke: 140 mm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE Pump drive power: ...
Used screw press for pressing grapes made by Vaslin model CEP 150S . Capacity approx. 750 L. Feed from the destemmer-crusher pump. Plastic feed hopper. Plastic tank. Suitable for all soft fruits as well as, for example, ground apples, etc.
clamping force: 800 kN injection volume: 154 cm³ screw diameter: 35 mm platen size: 430 x 660 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 800 kN - Mould mounting area: 430 x 660 mm - Clamping/opening stroke: 450 mm - Maximum mould installation height without heating plates: 300 mm - Maximum plate spacing without heating plates: 750 mm - Clamping direction: from below - Ejector stroke: 130 mm - Ejector force: 40 kN Injection unit: - Increased injection pressure: 2,180 bar - Maximum injection volume: 154 cm³ - Screw diameter: 35 mm - Screw length: 20D - Maximum screw speed: 20–400 rpm - Metering stroke: 160 mm - Injection: from above - Nozzle stroke: 250 mm - Voltage: 3 × 400 V, 50 Hz, N, PE - Pump drive power: ...
Four-column press SP 60 / 670 - Achtermann & Co. Stuttgart -Compressive force 60 tons -Passage between the columns 670mm -Passage between the columns/laterally 400mm - Table size 900x750mm -Height clearance 520mm -6x T-slots in the upper beam -6x T-slots in the table Dimensions: LxWxH 2x1.5x2 meters / Weight 3000 kg
clamping force: 250 kN injection volume: 134 cm³ screw diameter: 35 mm platen size: 300 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 250 kN - Heating plate dimensions: 300 x 300 mm - Heating power of the plates: 5.3 kW - Clamping/opening stroke: 330 mm - Platen distance with heating plates at maximum: 380 mm - Clamping direction: from below - Side ejector: yes - Stroke of side hydraulic ejector: 100 mm - Ejector stroke/force: 70 mm / 24 kN Injection unit: - Increased injection pressure: 1,580 bar - Maximum injection volume: 134 cm³ - Screw diameter: 35 mm - Screw length: 17.1D - Maximum screw speed: 20–480 rpm - Metering stroke: 140 mm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE Pump drive power: ...
Heavy-duty frame Adaptive follow-up support High precision pneumatic chuck Optional 3D bevel cutting Suitable Industries Tube furniture, fitness equipment, automotive exhaust, agricultural machinery, pipe distribution, guardrails & scaffolding. Gujdoza Rm Hspv Hcqcjc Application Scenarios Round/square tube cutting; holes, slots, arcs; short-run & mass pipe production.
PANHANS 116 YOC 1986 Motor power: 1.5 kW 2-lever operation Max. drilling depth: 130 mm Height adjustment: 135 mm Max. slotted hole length: 240 mm Height adjustment by handwheel Dowel pitch: 16 / 22 / 25 / 32 mm Miter ruler (adjustable) Workpiece stop 1 eccentr. Workpiece clamp Line laser (Z-laser) 230V Chassis Table size: 510 x 290 mm Weight: 220 kg incl. various Gebr. Drills Dimensions (approx. dimensions): W: 90 cm T: 125 cm H: 115 cm Manufacturer information
Key data: 40 t, 1280 mm, 900 mm
Spotting and Experimental Injection Press REIS TUS 90 OK-40T Year of construction 1975 40 t pressing force Clamping surface 900 × 1280 mm Stroke 1150 mm Tool weight up to 7 t Movable ejector Hydraulic motor 5.5 or 7.5 kW Machine weight approx. 7 t
clamping force: -- kN injection volume: -- cm³ screw diameter: -- mm platen size: -- mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand, used as a spare parts source for cannibalising 3x machines, model SAD 114/30 - Year of manufacture: 1999 - Problems with the control system 1x machine, model Super AD 76/15 - Year of manufacture: 2006 - Problems with the control system There are 3 machines built in 1999 and 1 machine built in 2006 available. The price is per unit. If you purchase several units a package price can be arranged. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25418 Technical data: - Printing capacity approx. 110 kN - Working stroke approx. 50 mm - Power stroke 12 mm - Projection approx. 150 mm - Table size 280 x 180 mm - Installation height adjustment up to max. 300 mm - 2 Hand control - Air inlet 6 - 8 bar - Total - space requirement approx. W 600 x H 2500 x D 900 mm - Weight approx. 400 kg
Key data: 120 kN
Mohrtek injection press, vertical loadable, horizontal pressing machine. please contact for more information
clamping force: 350 kN injection volume: 170 cm³ screw diameter: 36 mm platen size: 380 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 350 kN - Platen size: 380 x 300 mm - Heating power of the plates: 6 kW - Clamping/opening stroke: 200 mm - Clearance between the plates: 250 mm - Clamping direction: from below Injection unit: - Pressure: 1,050 kg/cm² - Maximum injection volume: 134 cm³ - Screw diameter: 35 mm - Max. screw speed: 30–110 rpm - Metering stroke: 165 mm - Injection: from above - Voltage: 3 × 400 V, 50 Hz, N, PE - Pump drive power: 11 kW - Hydraulic motor power: 10 kW - Dimensions LxWxH: 2,400 x 1,200 x 3,300 mm - Weight approx.: 3,000 kg The data for this ad was created with ModulMWS - the ...
Qty. 1 Second-hand Aluminium Extrusion Press Line Mfc.: Youngstown USA Force: 1650 MT Billet dia.: 6”, 152 mm Built: early 1980s, completely Revamped in 1999 Production start: 1999 Stopped: 2025, but still under power Billet size: 6”, 152 x 550 mm Press Type: Horizontal Hydraulic, Direct Extrusion PLC: LS XGK (Korea) Required floor space: 20 mtrs x 60 mtrs
NC HYDRAULIC SIMPLE PRESS BRAKE NOMINAL FORCE: 3000KN WORKTABLE LENGTH: 5000MM POLES DISTANCE: 3800MM THROAT DEPTH: 400MM STROKE: 300MM MAX OPEN: 600MM POWER: 45KW DIMENSION: 5000MM(L) X 2500MM(W) X 3200MM(L) LOCATION: F39, TGE KINDLY CONTACT: syweetopglove.com.my
The dimensions of the machine are LxWxH 2500mm x 1600mm x 2500mm. The weight is 8250kg. The machine is in a little-used condition.
Code: 0421 Brand: ORMAMACCHINE Model: NPC - CE Standard Hot press with diathermic oil heating for wood, joinery, furniture, custom-made furniture, panels, doors, composite materials and various – CE Standard Platen sizes mm 3000 x 1580 Solid steel platens with diathermic oil heating N° 6 pistons diameter 85 Opening mm 400 Platens heating by electric boiler Thrust 120 ton Guides side racks Mylar-coated platens Overall dimensions mm 3700 x 1850 x 2600 h
Desma Vertical Injection Moulding Machines Model Type D968 250 ZO ( S3 ) Stroke Volume 2000 cm3 Injection Pressure 1670 bar Platen 560 mm x 630 mm Extended Daylight 860 mm Top and Bottom Hydraulic ejectors 400 mm stroke Strip Intake Control With Vacuum Pump Years: 2014 / 2015
Offer 26175 Technical data: - Max. pressure capacity up to 25 t - Max. plunger stroke 160 mm - Installation height without straightening unit 675 mm - Projection to the middle of the ram 250 mm - Table size approx. 1300 x 300 mm - Working speed AB approx. to max. 30 mm/s - Working speed to approx. 100 mm/s - Oil filling quantity approx. 150 ltr - Drive 400 V / 10 kW - Space requirement approx. W 4900 x H 2400 x D 1500 mm - Weight approx. 3000 kg - with: - Straightening table extension 2030 + 1520 mm - Transfer carriage with mounts on straightening table - Lace intake - Roll recording - Directional stamp - Swivel switch with dial gauge
High: 2.100 mm, Long: 1.200 mm, Force: 20 TN, Width: 1.300 mm, Voltage: 220/380 V, Neckline: 160 mm, Lower speed: 18 mm / s, Stem travel: 100 mm, Total power: 5.5 CV, Rate of climb: 27 mm / s, Maximum aperture: 650 mm, Piston rod ø of: 100 mm, Surface of the table: 1050 x 360 mm, Specification: Hydraulics
The Bruderer BSTA 80H is an 80-ton high-speed stamping press built for heavy-duty progressive-die production, fitted with a BBV 320/200 strip feeder and Unidor tool monitoring. In stock in Pforzheim, ready for inspection. Nominal force: 800 kN (80 tons) Tool monitoring: Unidor Stroke rate: 100–1,000 spm Strip feeder: Bruderer BBV 320/200 Adjustable stroke: 16–63 mm Clamping plate area: 970 mm Main drive: 43 kW Power supply: 380 V / 50 Hz Ram area: 760 x 510 mm Table area: 950 x 910 mm Strip inlet height (adjustable): 80–180 mm Max. strip width: 360 mm Max. material thickness: 3 mm Machine dimensions: 2834 x 1742 x 3460 mm Weight: approx. 15,550 kg Operating hours (main drive): approx. 28,067 h More machines from brands Bruderer, Bihler, Soprem, Noxon, Huras, Schaal and Mabu on stock available on request
Slotted Hole Drilling Machine Holzkraft Type LLB 16 H Item No. 532 6617 Year of construction 2010 With dowel device Table size 500 mm x 200 mm Drilling width 200 mm Drilling depth 150 mm Drill head height adjustment 150 mm Wescott Drill Fiutter 0-16 mm Speed 3000 rpm. Motor power 1.1 kW Table fixed Drilling unit movable Weight 120 kg
The BSTA 50UL is a Bruderer high-speed precision stamping press rated at 500 kN (50 tons) nominal force, engineered for continuous progressive-die production at variable stroke rates from 100 to 1,120 strokes per minute. The press is equipped with a Bruderer BBV 202/120 strip feeder, delivering strip widths up to 203 mm and handling material thicknesses up to 2 mm. Adjustable stroke is set between 16 and 51 mm, with strip inlet height adjustable across a 50–140 mm range to accommodate varying tooling and material profiles. Nominal force: 500 kN (50 tons) Tool monitoring: Unidor Stroke rate: 100–1120 strokes per minute (variable) Strip feeder: Bruderer BBV 202/120 Adjustable stroke: 16–51 mm Mounting space / clamping plate: 760–940 mm Main drive: 22 kW Power supply: 400 V / 50 Hz Table area: 940 x 580 mm Strip inlet height (adjustable): 50–140 mm Max. strip width: 2 ...
Code: 0120 Brand: ORMAMACCHINE Model: NPC/3000S - CE Standard Hot press with diathermic oil for wood, veneer, wood panels, coated panels, veneer, composite materials, cork, aluminium and various materials - CE Standard Platen dimensions mm 3000 x 1300 Thrust ton 70 N° 6 pistons Opening mm 400 Motor Hp 2 Heating with diathermic oil by electric boiler Mylar-coated platens Overall dimensions: mm 3600 x 1550 x 1900 h Weight kg 3500
Key data: 250 t
Press force: 2500 kN Installation height: 800 mm Stroke: 500 mm Table: 900 x 630 mm (1200 x 630 mm) Plunger: 750 x 450 mm (900 x 550 mm) Projection: 360 mm Speed from: 200 mm Speed on: 110 mm Height of the machine: approx. 3,600 mm Weight: approx. 9,000 kg Connection: 20.5 kW Machine can be sold in original condition or overhauled with current UVV
Key data: 160 t
Press force: 1600 kN Installation height: 800 mm Stroke: 500 mm Table: 900 x 630 mm Plunger: 750 x 450 mm Projection: 360 mm Speed from: 200 mm Speed on: 125 mm Height of the machine: approx. 3,450 mm Weight: approx. 7,000 kg Connection: 17 kW Machine can be sold in original condition or overhauled with current UVV
Fully automatic baler Manufacturer: PAAL Type KONTI 325 D Operating hours: approx. 22,300 h Year of Make: 1999 Technical manufacturer data: Press force: 94 t at 300 bar Specific pressing pressure: 10.3 kg/cm² Drive power: 2 x 55 kW Total connected load: 150 kW / 280 A Oil tank capacity: approx. 3,100 litres Throughput under operating conditions: approx. 430 m³/h Performance at: 35 kg/m³ bulk density: approx. 14.5 t/h 60 kg/m³ bulk density: approx. 25.0 t/h 100 kg/m³ bulk density: approx. 39.5 t/h Filling opening: 1,020 x 2,000 mm Bale size: 750 x 1,100 mm Binding: 4-fold vertical Machine weight: approx. 28 t Bale weights: 525 to 800 kg including: - Free kicks - Whirlpool can be inserted from the rear
Key data: 315 t, 310 mm, 250 mm
Condition used Press capacity 315 t Stroke 250 mm Daylight 310 mm Table size (left to right) 320 mm Table size (front to back) 385 mm Table height 1250 mm Speed at max. press force 7.5 mm/sec Pressure speed at f max. 0.3 mm/sec Return speed 24 mm/sec Oil quantity 390 l Driving power 380 V/ 50 Hz/ 2.2 kW Dimensions 1950 x 800 x 2000 mm Height of machine above floor 2000 mm Total weight 2.4 t Mode of operation oil hydraulic Calibrating presses Description Contact the seller for more information Interested in this machine?
Stage Press / Eccentric Press Erfurt Pressen Erfurt 3, Maintenance No. 156, press force 320 t, year of construction approx. 1980, with 15 press punches, electronic transfer line, conversion by PBK, system consisting of double unwinding reel PBK, straightener PBK, feed, blank cut (Machine is partially dismantled after defect, without tools)
Used Italpresse UT/6 hot press for finishing with the application of veneers of chipboard, plywood panels. MDF, solid or plastic laminates, whether or not for aluminium and other metals The press plates are solid perforated steel plates Table top size: mm. 3000 x 1300 Maximum opening mm. 400 Diathermic oil heating of the hobs with electric boyler complete with circulation pump Boyler da 27 kw - 380 V Selector switch for use 50% of the boyler power - 13.5 KW in the first position or 27 KW in the second position - Pressing time setting with automatic opening Max pressure 300 bar Exclusion of 2 side cylinders from the control panel Protection Mylar on the tops Machine dimensions: mm. 3700 x 1700 x H. 2100 Weight kg. 6600 Machine according to CE regulations
1 Piece Used Automatic Baler Manufacturer: PRESONA Type: LP 80 VH1 Year of Make: 1993 Technical data: Press force: 78 t Specific pressing force: 9.5 kg/cm² Drive power: 1 x 55 kW Throughput capacity: approx. 400 m³/h Filling opening: 1,500 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 450-600 kg Binding: 5-fold vertical Oil tank: approx. 1,000 litres capacity, standing separately next to the machine Machine weight: approx. 22 t
1 Piece Used Automatic Baler Manufacturer: PRESONA Type: LP 80 CH2 Year of Make: 1993 Technical data: Press force: 78 t Specific pressing force: 9.5 kg/cm² Drive power: 2 x 45 kW Throughput capacity: approx. 560 m³/h Filling opening: 1,650 x 1,100 mm Channel format: 750 x 1,100 mm (H x W) Bale weights: up to approx. 450-600 kg Binding: 5-fold vertical Oil tank: approx. 2,000 litres capacity, standing separately next to the machine Machine weight: approx. 30 t
1 Piece Used Automatic Baler Manufacturer: SACRIA Type: SAPHIR 340 AT Year of Make: 2001 Technical data: Press force: 40 t Specific pressing force: 5.10 kg/cm² Drive power: 15 kW Throughput capacity: approx. 90 m³/h Filling opening: 1,250 x 1,100 mm Channel format: 900 x 800 mm (H x W) Bale weights: up to approx. 300-350 kg Binding: 4-fold vertical Oil tank: approx. 400 litres capacity Machine weight: up to approx. 6.5 t
Briquetting machine PRODECO E 60 Super Vertical Briquette diameter 60 mm Max. briquette length 60 mm Motor power 5.5 kW Capacity 10/60 Kg/h Pressing force 900 kg/cm² Container dimensions 1600 x 1600 mm Supply Voltage 400V Dimensions 215x180x150cmH Weight 870 kg Year of manufacture 2019
Shelf press for veneering SIPA 2500×1280 Shelf length 2500mm Shelf width 1280mm Load height 440mm Operating pressure 120bar Press on 4 cylinders Shelves heated with boiler water
Manni 2500×1300 veneer shelf press Shelf length 2500mm Shelf width 1300mm Load height 410mm Working pressure 300bar Press on 4 cylinders Net price
The used DORST DK 100 is a robust sizing and powder compaction press designed for high-performance industrial applications. Capable of a maximum pressing force of 1000 Kn and a withdrawal force of 500 Kn, this machine provides powerful and reliable operation. It accommodates a filling height of up to 110 mm with a pressing travel of 50 mm, ensuring versatility for various compaction tasks. The upper punch stroke is 140 mm, with adjustable travel up to 75 mm, allowing for precise control over pressing operations. This model offers between 5 and 22 strokes per minute, giving you flexibility in production rates. The die return force is 100 Kn, while the supporting force in the pressing position reaches 300 Kn. Pneumatic operations are supported with an upper punch preload of up to 30 mm and compressed air consumption of approximately 80 liters per minute. It requires a total connected load ...
- Basket capacity: 1200l - Elastic membrane new, 2026 - Machine with integrated compressor - With central filling, ball valve NW 80 - Feet: H: 300 mm - Probes in the juice vat for cider pump control - With tester emptying trolley - Machine in very good condition, little used
The Dorst TPA 15/3 is a used mechanical powder compaction press designed for precision and efficiency in industrial applications. It provides a maximum pressing force of 150 kN and a withdrawal force of 100 kN, supporting a variety of compaction tasks. With an upper punch stroke of 100 mm and a range of 70 mm for adjusting the travel, this machine offers flexibility for different requirements. Operating at speeds of 7 to 32 strokes per minute, it ensures a reliable production throughput. This press allows for a maximum filling height of 70 mm and pressing travel up to 35 mm, suitable for a range of powder compaction needs. The machine is fitted with a compressed air system that has an intake of around 70 liters per minute and a total connected load of approximately 6 kW. It is compact yet robust, with dimensions of about 1400 mm in width, 1300 mm in depth, and 2650 mm in height, weighing ...
- Elastic membrane in good condition - Diaphragm in very good condition - Machine with integrated compressor - With central filling, ball valve NW 80 - With Pressostat and alarm siren - Feet: H: 500 mm - Probes in the juice vat for cider pump control - Machine in good condition
Offer 26185 Technical data: - Max. pressing force 160 t - Max. ram stroke approx. 500 mm - Average working speed approx. 92 mm/s - Return speed 125 mm/s - Installation height approx. 1000 mm - Projection to the middle of the ram 360 mm - Plunger clamping pin 40 mm - Table size 900 x 630 mm - Table bore / breakthrough 220 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 17 kW - Space requirement approx. W 1150 x H 3400 x D 1850 mm - Weight approx. 7500 kg
Hydraulic briquetting press manufactured by UMP Technika, model BP-600A, designed for the compaction of biomass and various industrial by-products in high-density briquettes. It offers a production of up to 600 briquettes/hour and a maximum compaction pressure of 1,700 kg/cm², to process product with a maximum humidity of 15% and produce briquettes of 150 x 60 mm (base) x 40-105 mm (adjustable height). The machine works continuously and automatically, and incorporates an electrical panel with Siemens PLC, frequency inverter and hydraulic group. Technical characteristics Model BP-600A Year of manufacture 2017 Power supply 33kW 400 V 50 Hz Production 600 Kg/h Documentation Maintenance Manual Operation Manual Electrical diagrams In your state
Industrial pellet press manufactured by Bühler, model DPUC, designed for the continuous production of pellets from different raw materials. The equipment incorporates a 6 mm die and is prepared for a capacity of approximately 2.5 tons per hour, depending on the product and process conditions. The press is equipped with a roller compression chamber, conditioner for product pre-treatment and support bed. The assembly is complemented by a stainless steel worm conveyor, intended for feeding or evacuating the product in the pelletizing line. Technical characteristics DPUC Model Year of manufacture 2005 Production 2,500 Kg/h In your state
Pressure: 16 tons Table dimensions: 800 mm x 410 mm Hammer dimensions: 350 mm Maximum stroke: 90 mm Motor power: 0.9 kW Weight: approx. 500 kg Machine dimensions: 800 mm x 900 mm x 1400 mm Very fast and powerful Two-hand operation for safe use Simple and intuitive operation Machine in perfect working order
pressure: 40 t throat: 220 mm stroke: 8-88 mm stroke - stepless adjustable: 30-140 mm ram adjustment: 63 mm weight of the machine ca.: 2600 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 6,3 t throat: 200 mm stroke: 200 mm dayligth: 600 mm total power requirement: 2,2 kW weight of the machine ca.: 0,78 t dimensions of the machine ca.: - m Hydraulic Press 63 kN Stroke 200 mm, Throat 200 mm, feed rate: down 165 (28) mm/s, up 510 mm/s. Wheight 780 kg. Workspace: Table 450 x 380 Drive: 2.2 Movie: https://www.youtube.com/watch?v=tcxXfKlrFLY The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 5 t distance between columns: ca. 300 mm table surface area: ca. 280 260 mm dayligth: ca. 200 mm ram - range of adjustment: ca. 150 mm Shipping weight: ca. 450 kg Packing: ca. 0,8 0,7 1,55 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40.0 t chamfer lenght: 1600 mm distance between columns: 1100 mm stroke of upper beam: 100 mm throat: 195 mm working feed: 10.0 mm/sec return speed: 70.0 mm/sec : 180 bar work height max.: 840 mm table width: 110 mm dayligth: 295 mm Control: ATL 550 total power requirement: 5.5 kW weight: 2500 kg range L-W-H: 2100 x 1200 x 1800 mm - in checked conditions - machinevideo - https://www.youtube.com/watch?v=cp3ge7VbjTA Equipment: - NC-controlled hydraulic press brake, with torsion shaft - with ATLANTIC NC control - model ATL 550 Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1 Y2 axis) Possibility of programming different programs Memory capacity max. 200 programs - max. 400 blocks Swivel control panel, left front - Electro-motorized backgauge (X axis) with 2x stop fingers, manually adjustable (R Z axis) - Tool holder system A - with top wedge crow ...
maximum number of results exceeded
please refine your search
