filling machine 25 used for sale

Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007

Fully functional welding machine

cutting diameter: 250 mm saw band length: 3100 x 27 x 0,9 mm capacity 90 degrees: square: 220 mm capacity 90 degrees: flat: 280 x 190 mm band speed: 37 / 74 m/min sawing motor: 1,5 kW weight of the machine ca.: 0,5 t dimensions of the machine ca.: 1,6 x 1,4 x 1,3 m Miter band saw - Semi-automatic - Double miter - Material detection during lowering The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: max. 366 mm turning length: 705 mm control: M 730 BM MAPPS IV greates pass round over bed: 920 mm Swing dia. over traverse guideway: 742 mm Main spindle:: turning speed range - main spindle: 4.000 min/-1 power capacity - main spindel: 18,5 / 15 kW spindle nose: JIS A-8 spindle bearing diameter: 140 mm spindle bore: 91 mm max. usable bar diameter: 80 mm chucking diameter: 250 mm Subspindel:: Spindle speed range subspindle: 6.000 min/-1 power capacity - Sub spindle: 11 / 7,5 kW spindle nose: JIS A2-5 spindle bearing diameter: 85 mm spindle bore: 43 mm max. usable bar diameter: ( - ) mm chucking diameter: 170 mm axis stroke:: x-travel: 260 mm z-travel: 795 mm Y - Axis: +/-50 mm rapid traverse ( X / Y / Z ): 30 / 10 / 30 m/min turret:: number of toolpositions: 12 pos. tool taper: BMT 60 Schank height for square tool: 25 mm Drill shank diameter: 50 mm turret change time: ...

GRP 250to year 2000 Needle bearing to screw shaft defective, machine stopped. Find more here - / Contact us at -

Stainless steel tanks Capacity 250 litres Cylindrical stainless steel tank standing on feet single-walled, hinged lid Agitator from above

pressure: 10 t distance between columns: 260 mm dayligth: 210 mm table surface area: 275 x 260 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Vibrating Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTyp: SRC-N 250-2LSer.- No: 03613 Year of Construction: approx. 2000Pot Diameter Bottom: 250 mmPot Diameter Top: 380 mmPot Inner Height: approx. 70 mmSorting Lane Width: 30 mmTotal Height (Drive + Pot with Sorting Path): 390 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz control unit

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Shaking Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTtype: SRC-N 250-2LSer.- No: 03609 Year of Construction: approx. 2000Pot Diameter Bottom: 300 mmPot Diameter Top: 350 mmPot Inner Height: approx. 25 mmSorting Track Width: approx. 30 mmTotal Height (Drive + Pot with Sorting Track): 380 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Shaking Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTyp: SRC-N 250-2LSer.- No: 03611 Year of Construction: approx. 2000Pot Diameter Bottom: 300 mmPot Diameter Top: 350 mmPot Inner Height: approx. 25 mmSorting Track Width: approx. 30 mmTotal Height (Drive + Pot with Sorting Path): 380 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz- The

Travel X/Y/Z: 800mm/800mm/800mm, feed force X/Y/Z: 15000N/15000N/17500N, feed speed X/Y/Z: 50m/min, max. rotary table speed: 25rpm, spindle diameter: 100mm, tool holder: HSK 100, spindle power S1-100%: 40kW, spindle speed: 6000rpm. Magazine capacity for a maximum tool diameter of 280mm: 23. Max. pallet dimensions X/Y: 630mm/630mm, max. pallets in the system: 6, coolant tank volume: 1500l, 50bar high-pressure pump delivery rate: 22l/min. Machine dimensions X/Y/Z: approx. 6300mm/4900mm/4000mm, weight: approx. 19,300kg, control: Siemens 840D powerline, operating hours: 74,637h. Includes integrated tool monitoring IPM, remote diagnostics via modem, Renishaw MP10 touch probe, RSP 4-position round storage, chip removal, coolant system with Knoll VRF 250 vacuum rotary filter, pallet changing device, 6 pallets, 4 of which are clamping towers with universal clamping bars, approx. 100 HSK 100 tool ...

Travel X/Y/Z: 2500mm/900mm/800mm, speed: 18000rpm, spindle power: 35kW, max. table load: 3000kg, tool places: 30, machine dimensions X/Y/Z: approx. 6500mm/3000mm/3000mm, weight: approx. 20000kg, control: Siemens Sinumerik 840D, operating hours: 55730h, spindle hours: 18696h. Z-axis brake defective, roller shutter in machine room defective, screen cable defective. Including cooling lubrication system Knoll VRF 250/1250, documentation available. On-site inspection is possible.

Travel X/Y/Z: 600mm/500mm/400mm, table dimensions X/Y: 900mm/600mm, spindle mount: SK40, speed: 6000rpm, tool positions: 24, feed: 6m/min, rapid traverse: 15m/min, machine dimensions X/Y/Z: approx. 4000mm/4000mm/2700mm, weight: approx. 5000kg. On-site inspection is possible.

Turning diameter over bed/face slide: 420mm/280mm, turning length: 1000mm, spindle bore: 78mm, max. speed: 3550rpm, drive power: 35kW, tool positions: 12 (with driven tools), tool holder: VDI50, rapid traverse: 10m/min. Machine dimensions X/Y/Z: approx. 4100mm/2300mm/2200mm, weight: approx. 10000kg, control: Siemens 840T with C-axis. After a buffer battery replacement, the software of the machine was deleted, whereby some machine parameters were deleted without documentation and automatic operation is currently impossible. Expected to be available from Q1, 2025.

With two machining modules, X-axis: -50 to 725mm, Y-axis: -200 to 300/ -250 to 250mm, rapid traverse X-, Y-, Z-axis: 18/12/30m/min, turning lengths: 1500/2000/2500/3200/4000/4500/6500mm, swing diameter: 780/ 880mm, turning spindle bore: 92/123mm, main spindle speed range: 0-3000/0-3000/2000/min, max. Turning/milling unit speed: 5000/6000/10000/min, max. tool length: 900/600/1000/300/900mm, quill stroke: 160/170mm, connected load: 102kVA, control system: SINUMERIK ONE / SINUMERIK 840D sl, drive system control: SINAMICS S120, weight: 17t. On-site inspection is possible.

An HMS punching machine is available. Pressing force: 250t, stroke height: 40mm, installation height: 450mm, ram adjustment: 20mm, stroke rate: 120 strokes/min, overall system dimensions X/Y/Z: approx. 17000mm/8000mm/3500mm. Including coil and strip processing. Documentation available. On-site inspection is possible. Expected to be available from September 2025.

Load capacity: 25t, center of gravity distance: 700mm, eccentricity: 250mm, speed: 0.66rpm, tilt range: 0°-130°, tilt time: 120s, table height (flat): 1930mm, axis of rotation height: 1600mm, table diameter: 2500mm, motor power tilt/rotate: 7.5kW/4.5kW, total length: 3000mm, total width: 2500mm. Documentation available. On-site inspection is possible.

A complete 5-layer coextrusion blown film line with 5 extruders and all peripheral equipment is available. Total line dimensions X/Y/Z: 14m/22m/11m, blow head: Kiefel Worms FSBK 500 with IBC, die diameter: 500mm, film width range: 700mm-2000mm, haul-off width: 2000mm, winding width: 2000mm, line speed: 120m/min, melting capacity: 500kg/h, total power requirement: approx. 300kW. 1) Double winder Wintech, winding width: 2000mm, film thickness range: 35µm-150µm, max. roll diameter: 1000mm, max. roll weight: 1900kg, core inner diameter: 152mm/6inch. 2) Extruder Kiefel Worms 70.29D, power: 89kW, screw: 5-zone barrier screw, speed: 125rpm, renewed: 2010. 3) Adhesive extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 4) Center extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone core progressive screw, speed: 175rpm. 5) Adhesion promoting extruder Kiefe ...

Decoiler Coil weight: 2,5 ton Material width: 50 - 500 mm Coil exterior diameter: 1400 mm Expansion range: 420 - 520 mm Leveller / Straightener Material width : 500 mm Number of levelling rolls: 9 pcs. Diameter of the levelling rolls: 50 mm Number of pinch rolls: 2 pcs. Material thickness: 6 mm Cross section: 3000 sq mm Feeding speed: 6 - 24 m / min

A Trima CNC gantry machining center is available. Workpiece dimensions X/Y/Z: 2500mm/1100mm/80mm, spindle power: 7.5kW, speed: 24000rpm, tool positions: 10, traversing speed X/Y/Z: 55m/35m/15m/min. Machine dimensions X/Y: approx. 4400mm/2500mm, weight: approx. 3200kg, control: Siemens Sinumerik. The machine has a control defect. The reference run is aborted. Documentation available. On-site inspection is possible.

cutting width: 150 mm machine weight ab.: 300 kg : 27468 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: ja vice: 1 quill stroke: ja : : 2.000 mm weight of the machine ca.: 790 kg strong material: Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: M01.43870 frequency: 50 Hz voltage: 400 V : 24 V connected load: 48 kW rated current: 63 A control: Siemens 840 D turning diameter: 250 mm turning length: 100 mm weight of the machine ca.: 7,5 t turning length external: / innen 100 mm workpiece length - min.: 29 mm workpiece length - max.: 100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 250 mm turning length: 100 mm control: SIEMENS 840 D total power requirement: 35 kW weight of the machine ca.: 7500 kg dimensions of the machine ca.: m E M A G (Germany) Vertical CNC Controlled Hard Turning and Grinding machine with tool turret and workpiece handling System Model VSC 250 DS Year 2004 # M7 28.69324 _______________________________________________________ Turning Ø, max. 250 mm Turning length internal / external 100 mm Workpiece length min./max. 29 – 100 mm 6-positon tool turret Ø / swing-Ø 480/790 mm Workpiece spindle Slide travel, X / Z / stroke 680 / 400 / 200 mm Feed rate / Quick feed X/Z 45/30 m/min. Feed force X/Z 5,5/11 kN Spindle speed 4.300 / 6.000 rpm Spindle drive 28 kW Total electrical load, ...

faceplate diameter: 2500 mm swing diameter: 2865 mm turning height: 3000 mm Control: R & D type: MTC 4 Rest: 2 slide adjustment: 1500 mm turning speeds: 140 U/min tool change unit: 12 Pos. total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Machine is modernized The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was cre ...

Saw blade diameter: 255 mm Sawblade tiltable: 45 ° Cutting height: 75 mm Table dimensions: 640 x 920 (ausgezogen) mm Saw blade: 30 mm Motor output: 1,6 kW connected load frequency: 230 V machine weight ab.: 32 kg Dimensions (L/W/H): 720 x 1080 x 920 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding wheel diameter: 250 mm no. of working stations: 2 Stück connected load frequency: 230 V turning speeds: 2850 U/min total power requirement: 1,5 kW weight of the machine ca.: 25 Kg dimensions: 0,65 x 0,32 x 0,35 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 255 mm saw band length: 2765x 0,9 x 27 mm cutting width: 300 x 180 mm turning speeds: 35 + 70 U/min total power requirement: 1,8 kW weight of the machine ca.: 450 t dimensions of the machine ca.: 1,7 x 1,23 x 1,75 m SPECIAL PRICE! Double miter metal band saw, frequency converter hydraulic semi-automatic GBS 250 Super HA-I Easy • miter left 60° + right 45° • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Hydraulic vice can be moved sideways a. • Guided, high quality industrial bearings • Solid vice + machine casting • Large machine bed • Machine base with tool compartment and chip drawer • Cut monitoring by ammeter • Cutting pressure feed regulator • Support roller (infeed side) • Ball bearing turntable Semi-automatic function: 1. Clamp material 2. Saw starts 3 ...

plate thickness: 3 mm blade length: 250 mm angle adjustable from - to: fest 90 Grad table surface area: 900 x 790 mm total power requirement: kW weight of the machine ca.: 0,65 t dimensions: 1,2 x 0,9 x 1,1 m Hydraulic notching machine - Footswitch - 2 pcs. sheet metal stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 2,5 kN stroke: 45 mm throat: 90 mm Working height from to: 80 - 220 mm table surface area: 120 x 60 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x 390 mm Hand presses with rack HZ 250 The power is transmitted via a rack and pinion construction. she finds their use where during the working process a constant pressure is needed. Precisely manufactured, spindle hardened and ground, unlimited service life Long spindle guide, optimal pressure performance, T-slot according to DIN 650 milled in the middle, sliding blocks fit exactly. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 870 mm band speed: 18 - 110 m/min Control: CNC total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,63 t dimensions of the machine ca.: 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 255 Super VA-I CNC • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start detection) • Frame and gearbox made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • High performance positioning with incremental encoder (CNC) c. • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-a ...

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 125 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 0,75 kW weight of the machine ca.: 0,135 t dimensions of the machine ca.: 1,25 x 0,6 x 0,6 m Speed in 6 levels 125 - 2000rpm. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. (Independent) Fixed bezel. Revolving bezel. 4-fold steel holder. chip tray. back panel. spindle protection. Hardened bed rails. Longitudinal feed with left / right switching. Set of change gears. Associated Tools. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 250 mm saw band length: 3150 x 27 x 0,9 mm table height: 700 mm cutting width: 250 x 320 mm cutting speed: 25 - 90 m/min dimensions of saw-band: 2480 x 27 x 0,9 mm : 120 mm : 120 mm : 190 mm Impact energy: 190 mm connected load frequency: 400 Volt total power requirement: 1,5 kW weight of the machine ca.: 0,5 t dimensions: 0,95 x 1,16 x 1,98 m Rock-solid band saw for solid material - Double miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 870 mm band speed: 18 - 110 m/min total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,63 t dimensions of the machine ca.: 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 250 Super VA-I MPS • Miter left. 45° automatic operation • Miter left. 60° semi-automatic operation (cuts without programming) • Shockproof and ergonomic control panel with oil-proof EPDM cover a. • Material height sensor c. (Automatic cut start detection) • Frame and gearbox made from one piece, very quiet cutting and very low vibration • Chip tray can be removed (disinfection) • Easy access to the saw, material and feed unit • Foldable safety cover • Fine feed adjustment • Semi-automatic. Cut! Saw automatically with microprocessor control Adj ...

turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,3 x 0,6 x 0,65 m Benchtop lathe 3-axis LCD digital display system fully assembled. Longitudinal feed. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. Clamping plate. 4-way steel holder. Clock for thread cutting. Drip tray Hardened bed tracks. Emergency stop switch. Forage protection Set of wheels. Appropriate tools. Base cabinet is optional The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 250 mm capacity 90 degrees: round: 80 mm capacity 90 degrees: square: 70 mm capacity 90 degrees: flat: 95x60 mm capacity 45 degrees: round: 70 mm capacity 45 degrees: square: 60 mm capacity 60 degrees: flat: 65x60 mm total power requirement: 1,0 kW weight of the machine ca.: 0,075 t dimensions of the machine ca.: 0,3 x0,8 x0,75 m SPECIAL PRICE! The ideal metal circular saw for workshop and assembly • For miter cuts left up to 45° • For sawing steel, stainless steel and, to a limited extent, aluminum profiles • Spindle vice with double clamping arm for low-burr cuts • Optionally with 230 V or 400 V motor • Automatic cooling directly on the saw blade • Double bearing for saw head • 24 V safety switch in the handle with restart lock • Length stop, assembly tool • Subframe (option) additional price 172,-EUR ATTENTION: Price is without saw blade! (saw bl ...

turning diameter over bed: 250 mm turning diameter over slide rest: 130 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 20 mm tailstock quill taper MT: 2 tailstock quill stroke: 60 mm metric threading: 0,4 - 3,0 mm thread - inch: 10 - 44 TPI thread - module: 0,2 - 12,5 mm connected load frequency: 230 V total power requirement: 1,0 kW weight of the machine ca.: 0,12 t dimensions of the machine ca.: 1,09 x 0,59 x 0,45 m Equipped with - 20 mm spindle passage - adjustable guideways - Powerful 1.0 kW motor - continuously variable speed Scope of delivery: - 3-jaw chuck 100 mm, - 4-jaw faceplate chuck 125mm - standing and rotating bezel - Splash guard - Feed protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 8 mm blade length: 250 mm angle adjustable from - to: fest table surface area: 840 x 750 mm total power requirement: 3,0 kW weight of the machine ca.: 1,3 t dimensions: 1,4 x 1,1 x 1,5 m Hydraulic notching machine - Footswitch - 2 pcs. sheet metal stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: Suitable for dressing and profiling diamond and CBN grinding wheels. ccesories: Total enclosure., Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 15” LCD monitor (microscope with zoom 15‐120X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Grinding wheel holder:: HSK 50 E, Diamond grinding wheel diameter: 50 - 250 mm, max. width of grinding wheel: 70 mm, Grinding wheel bore diameter: 20 mm, Speed of ...

Machine designed for profiling and dressing flats, side, angular, radius and special shapes on diamond and CBN wheels. Especially suitable for single or multiple wheel packs., Accessories:, Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 19” LCD monitor (microscope with zoom 15‐70X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Protection cover., Specifications: Wheel spindle taper: HSK50E (alternatives possibl ...

For sale is a ProJet 2500Plus from 2017. The device is in perfect condition, test printing is possible (for an expense allowance, which will be offset against purchase)., Accessories: EasyClean System from 3D Systems, second build platform, Technology: MultiJet Printing

On behalf of a customer, we are selling a 3D Systems MultiJetPrinter type ProJet 2500Plus in very good condition. The machine was used as a dealer demo machine., The machine has been equipped with new drive belts and new filters. All materials have been removed according to the manufacturers instructions. The machine is empty. The printing time is approx. 1400 hours, 181,000 layers were printed with approx. 24KG of building material and approx. 33KG of support material., Equipment:, - 3D Sprint Basic Complimentary Software (on-line activation), Installation: 2016, Print modes: HD - High Definition, Net build volume (xyz) net build volume (xyz) hd mode: 294x211x144mm / 11.6x8.3x5.6in, Resolution (xyz) resolution (xyz) hd mode: 800x900x790 DPI; 32μ (0.0012 in) layers, Accuracy (typical): ±0.025-0.05 mm per 25.4 mm of part dimension. Accuracy may vary depending on printing parameters, ...

A new belt roasting machine for nuts in the food industry is available. Fuel: diesel/electricity/gas/LPG, output: 2kW, machine dimensions X/Y/Z: approx. 3600mm/1900mm/1950mm, operating hours: 31h. Roasting capacity per hour: hazelnut kernels: 160kg, shelled peanuts: 150kg, shelled peanuts: 35kg, shelled pistachios: 90kg, sunflower seeds: 70kg, pumpkin seeds: 70kg, almonds: 120kg, cashew nuts: 150kg, chickpeas: 120kg. Including salt kettle with a capacity of 35kg and fully automatic high-pressure belt washer. Documentation available. On-site inspection is possible.

bore capacity in steel (diameter): 55 mm arm length: 2500 mm workpiece height max.: - mm total power requirement: 8 kW weight of the machine ca.: 5 t dimensions of the machine ca.: 4 x 1 x 3 m Radial drilling machine MK 5 Spindle holder MK 5 Speed range 30 - 1500 min-1 Feed rates 0.05 - 0.6 mm/rev Space requirement approx. 3.7 x 1 x 3 m Weight approx. 5 tonnes (estimated) Working range: MK 5 x 2500 Drive: 3.7 / 6 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

carrying capacity: 250 kg number of suction cups: 6 suction cup dia.: 215 mm Vacuum lifter VH 6-250 for the horizontal transport of smooth, dry and airtight panels. Robust supporting structure made of steel, painted in RAL 2000 with low Own weight. consisting of: - 1x galvanized longitudinal beam with a length of 2,400 mm - 3x galvanized crossbeams with a length of 1,000 mm - 6x Springy, articulating and adjustable suction cup holders - 6x suction cups Ø 215 mm, the seal can be separated in case of wear whose metal supports can be changed inexpensively and without tools - 6x ball valves to switch off individual suction cups, thus also smaller formats can be lifted without having to move suction cups or traverses. - 1x spiral connection cable small helix: with an extension length of 3,500 mm, designed as an extension cable with CEE plug and coupling. is routed to the lifting device nex ...

cutting diameter: 255 mm saw band length: 2765 x 27 x 0,9 mm table height: 950 mm : 18-110 m/min : 255 mm capacity 90 degrees: square: 240 mm capacity 90 degrees: flat: 300 x 180 mm capacity 45 degrees: round: 210 mm capacity 45 degrees: square: 190 mm capacity 45 degrees: flat: 200 x 160 mm capacity 60 degrees: round: 135 mm capacity 60 degrees: square: 110 mm capacity 60 degrees: flat: 130 x 100 mm capacity 45 degrees: round: rechts 180 mm capacity 45 degrees: square: rechts 160 mm capacity 45 degrees: flat: rechts 180 x 100 mm : 1,5/1,8 kW : 350 kg : 1700 x 900 x 2000 mm Manufacturer no. 20437 Description: - Miter cuts left 60° and right 45° - Quick-action clamping stick can be moved in the T-slot for quick position changes - Hydraulic brake cylinder - Large ball-bearing turntable for easy miter adjustment (durable) - Chip clearing brush - Machine base with automatic cooling system  ...

current capacity: - kVA throat: - mm contact pressure capacity: - kp total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m No. 1244 CNC portal spot welding machine PEI PROG-2515 Working area: 2500 x 1500 Siemens control Welding capacity of the butt spot welder 3+3 mm Welding capacity of the gun 2+2 mm Feed rates: X+Y 800 mm/sec, Z: 400 mm/sec, A 120°/sec. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 t distance between columns: 600 mm stroke: - mm total power requirement: 22 kW weight of the machine ca.: 9 t dimensions of the machine ca.: 2 x 2 x 3,2 m No. 3421 Mould press 2500 / 700 kN Single stroke 2-hand Single stroke foot switch Automatic continuous run set-up and tipping Table 500 x 500 Working range: Pressure capacity 250 tonnes Drive: ^22 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

control: MAZAK Mazatrol 640T Nexus swing over bed: 610 mm swing diameter over bed slide: 350 mm turning length: 982 mm c-axis: indexing: 0.001 ° turning speeds: 4000 U/min tool taper: ASA A2-8 tailstock quill taper MT: 5 rapid traverse X-axis: 30 m/min rapid traverse Z-axis: 33 m/min Overall size: 4500 x 2000 x 1600 mm weight of the machine ca.: 6.5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 400 mm centre height: 195 mm turning diameter over slide rest: 246 mm turning length: 650 mm spindle turning speed - stepless: 0-2500 U/min total power requirement: 7,5 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 2x1.3x1.6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.