132,141 used machines on RESALE, but how to find them? Machine Search
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -Power: 0.6 kW 17350 rpm at 300 Hz -Voltage: 165 volts -Shaft mounting: Ø 16 mm L 10 mm -Number: 4x motors available -Price: per piece -Dimensions: 280/60/H140 mm -Weight: 4 kg
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -1x motor: 0.3 kW 18000 rpm at 300 Hz -Shaft mounting: Ø 20 mm L 25 mm -Weight: 3 kg
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -Motor: 0.23 kW 18000 rpm at 300 Hz -Shaft mounting: Ø 15 mm L 25 mm -Number: 5x motors available -Price: per piece -Dimensions: 200/70/H90 mm -Weight: 2 kg
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding band dimension: 150 x 2000 mm band speed: 33 m/sek. total power requirement: 3 kW weight of the machine ca.: 95 kg turning speeds: 2800 U/min Standard equipment: - Removable dust catcher - Fine adjustment of the band adjustment - Sanding belt - Eye protection - Motor protection switch - Operation manual - Sanding table - working height adjustment - surface grinding pad The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
band speed: 33 m/s grinding band dimension: 75 x 2000 mm total power requirement: 3 kW weight of the machine ca.: 75 kg turning speeds: 2800 U/min Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -Power: 0.23 kW -Speed: 18000 rpm at 300 Hz -Dimensions: 210/70/H100 mm -Weight: 2 kg
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -Motor: 0.6 kW 18000 rpm at 300 Hz -Shaft mounting: Ø 16 mm L 10 mm -Number: 2x motors available -Price: per piece -Weight: 3.3 kg
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -1x motor: 1.5 kW 17300 rpm at 300 Hz -Shaft mounting: Collet Ø 12 mm -Dimensions: 340 x 110 x H150 mm -Weight: 10 kg
plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 295 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 150 mm band length: 2000 mm band speed: 16,5/33 m/sec total power requirement: 2,6/3,37 kW turning speeds: 1400/2800 U/min weight of the machine ca.: 95 kg Equipment / Accessories: - Removable dust catcher - Fine adjustment of the band adjustment - Sanding belt - Eye protection - Motor protection switch - Operation manual - Sanding table - working height adjustment - surface grinding pad The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW range L-W-H: 900 x 600 x 1000 mm weight: 470 kg connected load: 400/50 V/Hz Equipment / Accessories: - Three driven rollers - Manual delivery of the upper roller - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: 4 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 132 mm tool adaptor: 40 mm speed: 5 m/min total power requirement: 2,2 kW weight of the machine ca.: 350 kg dimensions of the machine ca.: 1650x700x1280 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor -1x motor: 0.15 kW 11160 rpm at 200 Hz -Saw: max. Ø 150 mm -Motor: mounted on guides -Travel distance: 320/100 mm -Dimensions: 550/250/H330 mm -Weight: 17 kg
Thread cutter, thread cutting machine, thread drilling machine -Integrated reversing gearbox: with rapid return -Nominal input: 230 watts -Max. cutting capacity: M6 -Connection: 230 volts -Weight: 2.5 kg
Thread cutter, thread cutting machine, thread drilling machine -Integrated reversing gearbox: with rapid return -Nominal input: 230 watts -Max. cutting capacity: M6 -Connection: 230 volts -Weight: 2.5 kg
Nibbling machine, nibbler, nibbler, tin snips, circular scissors -Power: 900 watts -Max. cutting capacity: 3.25 mm -Dimensions: 500/220/H230 mm -Weight: 5.5 kg
shaft diameter: 60 mm Shaft revolutions: 6 U/min roll diameter: 215 mm pressure hydraulic cylinder: 180 kN dimensions: 1125x870x1620 mm weight: 820 kg Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 1050 mm plate thickness: 3,3 mm pre-bending: 3,0 mm roll diameter: 90 mm min. dia.: 130 mm total power requirement: 1,1 kw weight of the machine ca.: 570 kg dimensions of the machine ca.: 2100 x 800 x 1130 mm Domestic equipments: - Asymmetrical 3-roll round bending machine with motor drive - Upper roller swung out - Conical bending device - Main engine with brake device Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sanding belt width: 150 mm sanding belt length: 2000 mm band speed: 16,5/33 m/sec engine output: 2,6/3,37 kW Motor speed: 1400/2800 UpM weight of the machine ca.: 105 kg Domestic equipments: - vibration-free running smoothness - Working height adjustable - S1 motors with 100% duty cycle - Surface and contact grinding is possible - Removable protective cover for surface grinding - Connecting piece for double suction - Built to CE standard The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 495 kg range L-W-H: 1100x850x1100 mm Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Machine vice, sturdy vice, drill press vice -Jaw width: 155 mm -Clamping depth: max. 120 mm -Dimensions: 550/300/H160 mm -Weight: 38 kg
Machine reamers, reamer, reaming tool, locating knife cutting set -Various sizes: Ø 13-33 mm -various: recordings -Sale: only complete set -Weight: 7.2 kg
Double bench grinder, double grinding machine, pedestal grinder, pedestal grinder -Motor power: 0.5 kW -Speed: 3200/5200 rpm -Grinding discs: max. Ø 180 mm -Operating voltage: 380 volts -Dimensions: 500/500/H1550 mm -Weight: 170 kg
Counter support, counter bearing, bearing block, pillow block bearing, bearing for milling machine -Dovetail: 144 x 184 mm, 30 mm high -Drawing with the photos -Dimensions: 270/130/H195 mm -Weight: 12 kg
sheet width: 1250 mm plate thickness: 5,5 mm pre-bending: 5,0 mm roll length: 1280 mm min. dia.: 210 mm roll diam. toproll: 140 mm weight: 1365 kg range L-W-H: 2.020 x 900 x 1.200 mm Standard features: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - motorized rear roller adjustment - Digital display for back roller - induction hardened rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 63x4,2 mm external diameter: min. Ø 5 mm bending radius min.: 10 mm bending radius max.: 270 mm Bending Angle: max. 210 ° bending device: gegen Uhrzeigersinn total power requirement: 0,75 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 740x470x1030 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 215 mm shaft diameter: 60 mm Shaft revolutions: 6 U/min : 100x2 mm : 80x15 mm pressure hydraulic cylinder: 180 kN total power requirement: 2,2 kW weight: 720 kg dimensions: 1200x900x1700 mm Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 60x3 mm : 60x2,5 mm : 35 mm : 64x4 mm : R10-R300 bending speed: 2 U/min total power requirement: 1,5 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 595x363x900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Edge banding machine for shaped parts, edge bander, edge banding machine -Workpiece thickness: 10-85 mm -Heating fan: 6 kW, pre-coated edges -Cutting knife -Edge plate -Transport dimensions: 900/700/H1080 mm -Weight: 135 kg
Multifunctional punch, punch press, hole punch, pneumatic hole punch -operated: pneumatically -Year of manufacture: 1999 -Dimensions: 600/600/H1300 mm -Weight: 50 kg
Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 1 inch -Drive: via 3 gearboxes -Dimensions: 550/360/H240 mm -Weight: 55 kg
Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 2 inch -Drive: via 3 gearboxes -Dimensions: 550/360/H240 mm -Weight: 55 kg
: 200 kN stroke length max.: 200 mm working feed: 10 mm/sec return speed: 20 mm/sec : 480x1060 mm work height max.: 900 mm toolpiece height max.: 200 mm total power requirement: 2,2 kW : 200x12 mm bending capacity max. - round: 48x4,0 mm weight: 500 kg Overall size: 1010x480x1120 mm Domestic equipments: - with semi-automatic control (99 programs with 16 steps each) - including bending bolt (without punch) - Tool holder for dies - Foot pedal Equipment: - Stamp, small U = 145 mm 85 °, H = 200 mm, R = 5 mm - Quick change monometer 85 °, H = 200 mm, V = 63 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding band dimension: 150 x 2000 mm band speed: 16,5/33 m/sec engine output: 3,4/4,5 kW Motor speed: 1400/2800 UpM weight of the machine ca.: 105 kg Domestic equipments: - vibration-free running smoothness - Working height adjustable - S1 motors with 100% duty cycle - Surface and contact grinding possible - Removable protective cover for surface grinding - Connecting piece for double suction - Built to CE standard The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 560 mm y-travel: 450 mm z-travel: 450 mm rotary table dia.: 270 mm rotary table tiltable: 0 - 24 ° spindle taper ISO: 30 spindle turning speed range: 31,5 - 7100 U/min feed speeds: 1 - 10.000 mm/min control: SINUMERIK System 8 no. of tools in magazin: 40 wotkpiece diameter with 2 vacant positions: 100 mm workpiece length: 255 mm weight of tools max.: 6 kg total power requirement: 32 kW weight of the machine ca.: 11,6 t dimensions of the machine ca.: m = 5 axis machining centre Accessories: various tool fixtures, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
groove width: 16 mm x-travel: 16-200 mm table length: 1500 mm table width: 375 mm milling spindle: ISO 40 max. clampable toolpiece shaft diameter: 30 mm max. useable hobs, normal diameter: 40 mm distance between milling spindle and table: 150-250 mm axial move. of milling spindle (auto./manual): 120 mm vertical adjust. of milling slide (manual): 100 mm weight of the machine ca.: 3,1 t dimensions of the machine ca.: 2,00x1,40x2,40 m K4 - TECHDETAIL UK: 0,11 kW K4 - TECHDETAIL UK: 0,6/1,1 kW K4 - TECHDETAIL UK: 3 x 0,012-0,05 mm/U K4 - TECHDETAIL UK: 16x60 mm K4 - TECHDETAIL UK: 12 x 280 - 3550 U/min K4 - TECHDETAIL UK: 0,85 kW K4 - TECHDETAIL UK: 0-2,0 mm K4 - TECHDETAIL UK: 250 mm Condition: ready for production The machine is suitable for the manufacture of flutes and slots using undersize cutters with hydraulic adjustment. Roughing and finishing can be done in one single clamping. ...
Machine vice, sturdy vice, drill press vice -Vise: rotatable -Jaw width: 200 mm -Clamping depth: max. 245 mm -Dimensions: 550/370/H195 mm -Weight: 80 kg
Grinding machine, angle grinder, lathe tool grinding machine, thread drill grinding machine, milling cutter grinding machine -Angle adjustment -grinding device -Disc: Ø 190 mm -Drive: 0.2 kW -Speed: 2800 rpm -Dimensions: 700/700/H1400 mm -Weight: 275 kg
x-travel: 800 mm y-travel: 450 mm z-travel: 400 mm table surface area: 1385 x 305 mm spindle taper: SK 40 quill stroke: 200 mm spindle turning speed range: 50 - 3500 U/min control: HEIDENHAIN control: TNC 155 total power requirement: 5,8 kW weight of the machine ca.: 2,5 t dimensions: 2,25 x 2,0 x 2,4 m Accessories: electron. handwheeel, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 650 mm gear width: 200 mm max. module: 10 min. module: 1 work accuracy: DIN 6 clamping table diameter: 710 mm table bore diameter: 150 mm number of strokes - stepless: 35,5 - 560 c/min max. ram stroke: 230 mm feeds: 3,55 - 40 mm/min radial feed: 0,8 - 9 mm/min work-spindle diameter: 110 mm total power requirement: 28,2 kW weight of the machine ca.: 9 t dimensions of the machine ca.: 3,8 x 2,3 x 2,5 m Gear shaping machine for the production of spur gears, for Internal and external gears - Built under licence from LORENZ and identical in construction to LORENZ LS 630 complete Modernisation + overhaul in 2012 with: - new painting - new electrical system from Telemecanique - Counter Holder - Chip conveyor - Coolant unit - change gears Not used in production again after overhaul The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Diamond core drilling machine, core drilling machine -3x: drill stand -Max. Drilling capacity: Ø 60 mm -drilling depth: max. 400 mm -Drive: 1050 W -Speeds: 1500/3000 rpm -Core drill: Ø 18/24/29 mm -Sale: only complete -Weight: 70 kg
x-travel: 1000 mm y-travel: 508 mm z-travel: 460 mm size of pallet: 1240 x 550 mm numbers of pallets: 2 workpiece weight: 800 kg spindle taper ISO: 40 spindle motor: 5,5 kW turning speed range: 28 - 4000 U/min no. of tools in magazin: 30 control: MAZATROL M 1 total power requirement: kW weight of the machine ca.: 5,6 t dimensions of the machine ca.: 4,50 x 3,00 x 2,65 m acc.: chip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 1 inch -Drive: via 3 gearboxes -Dimensions: 550/360/H240 mm -Weight: 60 kg
Notching milling machine -automatic hydropneumatic milling feed -for milling cutters max.: Ø 250 mm
Clamp welding machine, foil welding machine -Connection: 220 V -Working width: 300 mm -Weight: 10 kg
Machine vice, vise -Jaw width: 250 mm -Jaw height: approx. 80 mm -Clamping depth: max. 310 mm -Weight: 120 kg
saw blade diameter: 70 - 230 mm sawblade width: 12 mm hole of sawblade: 10 - 50 mm grinding wheel diameter: 120 mm grinding wheel width: 6 mm grinding wheel hole diameter: 32 mm no. of teeth: 30 - 400 total power requirement: 0,33 kW weight of the machine ca.: 350 kg dimensions of the machine ca.: 0,80 x 0,70 x 1,70 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding wheel diameter: 200 mm no. of working stations: 2 Stück turning speeds: 2800 U/min dimensions of grinding wheel: mm grinding motor: 0,55 kW shaft cross cut: 32x40 mm total power requirement: kW weight of the machine ca.: 250 kg dimensions of the machine ca.: 1 x 0,6 x 1,2 m - Swing table 420 x 220mm - on the side. Movement 40mm - infeed against grinding wheel 70mm - Degree of inclination 30 ° - Grinding guide grinding device - Inclination of the mounting bracket 20 ° - Adjustment of the mounting bracket 45 ° - Infeed against grinding wheel 80mm - Height adjustment 90mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
maximum number of results exceeded
please refine your search
