127,851 used machines on RESALE, but how to find them? Machine Search
Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T
serial no.: 9174 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. film width: 355 mm max. speed: 0 /h serial no.: 8518 voltage: 100-240 V frequency: 50-60 Hz weight: 150 kg dimensions of press (L x W x H): Belichter 75 x 85 x 100 cm dimensions of press (L x W x H): RIP 70 x 50 x 70 cm repeating accuracy: +/- 25 µm RIP included up to 3000 dpi Red laser diode max. page width 355 mm max. 200 lpi screen ruling The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Capacity 3 ton/hour Motor power 200Kw Die diameter 1000 mm Number of rollers 5
CINCINNATI ARROW 2 1000 CNC WITH LOW HOURS WE OFFER AN NICE CONDITION VERTICAL MACHINING CENTRE YEAR 2003 WITH EQUIPMENT CONTROLS: GE-FANUC SERIES 18I-M CONTROL Table: 1,120 x 610mm TRAVELS: X : 1,020mm, Y : 510mm, Z: 560mm. Rapid Traverse : XYZ=24m/min. Maximum Cutting Feed : 15m/min. Maximum Spindle Speed: 8,000rpm. Spindle Taper BT40. 20 Position ATC. MACHINE WILL BE AWAILIBLE FROM BEGINING FEBRUARY 2024
Control ? Heidenhain Grinding lenght 1000 mm Gentre height 175 mm Dimension grinding wheel 400 mm Speed of grinding spindle 2000 rpm internal grinding attachment with rotation speed 20000 rpm, with grinding flange, measuring probe taster, machine has s
Control ? Heidenhain Grinding lenght 1000 mm Gentre height 175 mm Dimension grinding wheel 400 mm Speed of grinding spindle 2000 rpm internal grinding attachment with rotation speed 20000 rpm, with grinding flange, measuring probe taster, machine has s
Control: SIEMENS / MTC K Max.turning length: 1000 mm Max swing diametr over bed: 500 mm Quick Change Toolposts:1 Coolant tank:100l Made in Germany
: 100 t diameter: 40 mm throat: 760 mm total power requirement: 8,5 kW weight: 3.600 kg Accessories / equipment: - punching table The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Gurutzpe Super AT lathe. Distance between centers: 4000mm. Swing: 1020mm. Swing over carriage: 710mm. Swing in gap: 1320mm. Bore: 76,5mm. Motorized carriage. 4 independent jaws chuck. DRO Heidenhain.
Several used old-type tanks from the 80s, capacity approximately 10.000-20.000 liters
Forberg 1000LH Twin shaft paddle mixer Serial: 1720 Stainless twin shaft paddle mixer, 1000Kgs, bottom discharge doors, inspection hatch on each side, 3Ph
Lippert belt conveyor GF 1000-700-600 RA2251 Technical data: Conveyor length (NL): 1000 mm Frame width (NB): approx. 700 mm Belt width (GuB): 600 mm Overall height (BH): 105 mm Support feet optionally available Conveyor speed (v m/s): please contact us Drive: SEW geared motor, R17 DRS71M4/MM05 Electrical data: 50Hz V380-500, kW 0.55 / S1 Return pulley (UR): Ø = 81 mm Drive drum (AT): Ø = 81 mm Optionally available: Supports Side guides Frequency converter for stepless speed control Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: condition: good (used) Conveying length in mm: 1000 Nominal / outside width in mm: 700 Belt width in mm: 600 Driven: YES Engine type: SEW Eurodrive KW: 0,55/S1 Ampere: 1,30 Conveyor speed m / s: bitte Kontaktieren scope of delivery: without supports and side guides Für eine individuelle, fachmännische Beratung se ...
Universal Tool Milling Machine Make: MAHO Model: MH 1000 Technically flawless Accessories: - 3-axis digital display - Universal table 1,250 x 740 mm (T-slot 16 mm) - Vertical milling head SK 40 with tightening thread S 20 x 2 - 6 autom. Quill feeds 0.02/0.03/0.05/0.08/0.12/0.20 mm/rpm - Central lubrication, manually operated - Coolant device -Operating instructions The machine is open to the public. Ready for immediate use Delivery possible throughout Europe
Key data: 690 mm, 400 mm, 500 mm
Universal milling machine from WMW, type FW Good general condition Mechanically flawless function Milling Machine - Horizontal Make:WMW Fritz Heckert Type: FW 250x1000/2 Year of construction: approx. 1980 Control Type: Conventional Freight base: ex-site, freely loaded Location: 17034 Neubrandenburg Shipping time: immediately Price: 2,800 net free loading Technical details: x-travel: 690 mm Y-travel: 400 mm z-travel: 500 mm Table Mounting Surface:: 1250x250 max. table load: 1500 kg Spindle speeds:: 18 steps/step 55-2800 rpm Height above floor: 1350 mm Feed rate: 10-630 infinitely variable m/min Tool holder: SK40 Total power requirement: 6.3 kW Machine weight approx.: 2.0 t Machine dimensions LxWxH: L:1.8xW:1.7xH:2.0 m The work table can also be adjusted manually. The projection of the counter-holder boom = 500mm, the total length = 1050mm. with end pos ...
Universal Tool Milling Machine Make: MAHO Model: MH 1000 2x available! x-travel 1000 mm Tool holder SK 40 Digital. Head swivel +/- . Table tilt and swivel +/- . Quill stroke . - 3-axis digital display - Universal table 1,250 x 740 mm (T-slot 16 mm) - Vertical milling head SK 40 with tightening thread S 20 x 2 - 6 autom. Quill feeds 0.02/0.03/0.05/0.08/0.12/0.20 mm/rpm - Central lubrication, manually operated The machine is open to the public. Ready for immediate use Free loading, transport no problem. Financing possible at favourable conditions! If you have any questions, just write or call.
Key data: 1000 mm, 560 mm, 800 mm
Inv. Num. : 3714 Type: MH 1000 C Producer: MAHO Created: 1991 Parameters: Control system: Philips CNC 432 Hours: 62345 h Work table length: 1150 mm Work table width: 800 mm Tool magazine: 24 pieces Minimum vertical spindle speed: 20 1/min Maximum vertical spindle speed: 3400 1/min Mechanical feed length axis X: 1000 mm Mechanical feed length axis Y: 560 mm Mechanical feed length axis Z: 800 mm Cone: ISO 50 Maximum tool weight: 800 kg Machine weight: 7.3 t Equipment: 3 tool holders
PADE Trimming-Milling-Drilling Machine Model 1000/N: - Self-sliding worktop - Header blade D=400mm, 3 hp motor - milling machine with shaft D=30mm, motor hp 5 - 5-spindle drilling machine, 360° swivel, 3 hp motor Machine not according to CE standards, for export
Pile turner Rachner RD 1000 P; cleaned and tested; Platform size 128x80cm; Load capacity 1000kg; Opening width max.1400mm. Pile turner Rachner RD 1000 P; cleaned and checked; platform size 128x80cm; lifting capacity 1000kg; max.openig width 1400mm.
grinding diameter: 250,350,450 mm grinding length: 1000 mm centre height: 125,175,225 mm grinding wheel diameter: 400 mm grinding wheel width: 50 mm bore: 127 mm : MK5 work piece spindle speed: 20-400 U/min workpiece spindle - bore: mm grinding head swivelling: 360 ° grinding spindle head - swivable: 180 + - ° grinding spindle speed: 1500,1700,2200 U/min : 0,001-0,030 mm/Ø : 0-0,95 mm/Ø : ±8 ° longitudinal feed of the table: 1300 mm table speeds: 0,02-6 m/min : 130 kg : 130 inkl. Spannugkg kg : mm grinding depth: mm : 70 mm total power requirement: 6,5 kW weight of the machine ca.: 2,5 t dimensions of the machine ca.: 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines.Version R: Maschine hat Zentral ...
Polar Mohr stacking lift L-1000-W-6 => refurbished for ergonomic working at user-friendly working heights Specifications Tub size 1400 x 1000 mm Stroke max. 910 mm Load capacity max. 1000 kg The automatic lifting of the material to be cut makes it possible to the operator at an ergonomically favourable working height for him the material into the vibrator or directly into the cutting machine shop. However, the stacking lift can also be used for stacking material to be sliced. The lowering takes place semi-automatic. This means that the process will be manually started and passed through the light barrier automatically stopped. POLAR stacking lifts do not have to be can be anchored to the ground and can therefore be easily be converted. Customer: - The productivity of the cutting machine increases by up to 10%, as the working height during loading/unloading rem ...
Many of our machines are available from stock. Call and ask to find out more. Handheld laser welder LWH-1000-N QiLin The kit includes: - laser welder with built-in cooling system - welding gun with adjustable focal length and an accessory kit - fiber laser source of MAX Photonics - automatic wire feeder - set of cords - starter kit of protective lenses and nozzles Specifications - Laser source output 1000 W - Laser wavelength 1064 nm - Welding speed up to 120 mm/s - Power supply 230 Hz - Dimensions (including cable rack) 630x1300x1500mm Price included One-day training along with machine installation - 1 day up to 8 hours – machine installation and operational training. Operation Due to the revolutionary welding system, any user can achieve good working results after just a short training. The electrode feed cable allows the welder to work freely at multipl ...
Transnorm conveyor belt GF 26000-1100-1000 RA2289 Technical data: Conveyor length (NL): 26000 mm frame width (NB): 1100 mm, 1200 mm with motor belt width (GuB): 1000 mm Overall height (BH): 80 mm, 430 mm with motor Supporting feet: optionally available Conveying speed (v m/s): 0,2 Drive: SEW gear motor, R63DT100LS4TH Electrical data: 50Hz V380-500, kW 2,2 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 1998 condition: good (used) Conveying length in mm: 26000 Nominal / outside width in mm: 1100 Belt width in mm: 1000 Driven: YES Engine type: SEW Eurodrive Zentralantrieb mit Spannstation KW: 2,2 Conveyor speed m / ...
FOIL SEALING MACHINE type TS 1000 C-2 Year of Build 1980, Machine No: 1748, for the production of bags made of suitable Polyethylene and polypropylene films Product: Tren suture bag Processing: single-lane or dual-use printed two-lane unprinted Working width: max. 1000 mm Section lengths: 80 - 600 mm Film thicknesses: 2 x 0.015 - 0.100 mm depending on the welding wedge design Working cycles (mech.): max. 150/min. depending on film thickness, type of film, film quality and Section length Film web speed: max. 35 m/min Power consumption: 4 KVA Nominal voltage: 380 V Nominal frequency: 50 Hz Control voltage: 220 V Cooling water consumption: approx. 42 l/h Paint: light grey according to RAL 7030
LWB Steinl Injection Machine Type VREFE 1600/1000/170 Heating platen size 500 X 510 X 63 mm Sliding platens Top and bottom ejectors Clamping force 1600kN Opening force clamp 100kN Clamping stroke 395mm Injection volume E 1000 ccm Max. Injection Pressure E 2200 bar Injection volume EF 170 ccm Max. Injection Pressure EF 1800 bar Hours: 700 since new Year 2009 Weight 6000kg
Details Machine no. 2042.6616-05 Year of manufacture 2004 Circumferential diameter over bed 1,000 mm Circumferential diameter over bed 1,000 mm Center height over flat web 500 mm Bed width 560 mm Bed slide guide length 800 mm Spindle diameter front bearing 170 mm Spindle bore 128 mm Three-phase motor infinitely variable (AC motor) Drive power 37 kW Torque max. 4,069 Nm Total speed range 6.4 - 1,600 Gear stages 2 Heidenhain control system Manualplus 4110, completely renewed about 1 to 2 years ago 2 Lynettes Equipped with rotary power chuck, diameter approx. 500 mm. Including a lot of accessories of clamping jaws, estimated 15 sets, as well as approx. 15 sets of Multifix base holders, size D. Machine was equipped with a separate milling device, with its own control system, value approx. € 20,000.00. Only served by the owner, ver ...
Ink-Jet Printer Manufacturer : Citronix Type: CI 1000 Technical specifications : Line: 31 dot-5 line IP proteciton: Nema 4 (IP 55) Self-cleaning Documents: available
Axis:XYZ (3-axis) Max. travel:950x500x450 Tool:SK-40 Control:HEIDENHAIN ITNC 530
used
Dear Ladies and Gentlemen, We have constantly used transformer stations for wind turbines from 630 KVA to 2500 KVA in very good condition in stock
Distance between centers: 1000 mm, Height of points: 230 mm, Main engine power: 9.2 Kw, Working wheel dimensions (od x id x width): 500x80x203.2mm, Ø max to be rectified: 460 mm, Tailstock cone: MORSE 4, Workpiece head cone: MORSE 5, Max. Z axis travel : 1115 mm, Max. X axis travel: 260 mm, Approximate dimensions (length x width): 440x370 cm, Approximate Weight: 4700 Kg
Nominal force, tf 1000 The slider does not reach BDC, mm 12.5 Slider stroke, mm 600 Frequency of continuous strokes, min-1 12...18 Highest frequency of single strokes, min-1 9...13 Closed height, mm 1500 Adjustment of closed height, mm 400 Slider dimensions, mm from left to right 4500 front to back 2500 Dimensions of the die plate, mm from left to right 4500 front to back 2500 Main drive electric motor power, kW 200 Overall dimensions, mm from left to right 6745 front to back 5400 height above floor level 9360 Weight kg 320000
Key data: 1000 mm, 1 t
for one-sided loading and unloading, with large stop plate and brake Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 1000 mm Coil weight: 1000 kg Machine Number: 308 Colour: blue/yellow Machine weight approx.: 350 kg Dimensions: 800 x 1800 x 1400 mm Coil width: 1000 mm Clamping range: up to 510 mm Load capacity in kg :1000 kg
calibrating sanding machine model LEVIGALTECNICA MIKRO SRTV/C mm.1000 second hand machine carpet in rubber max. working width mm.1000 machine composed by 1 belt combined : calibrating roller in rubber diam.mm.150 + pneumatic pad main motor power Kw 10 belt dimension mm. 2150 x 1030 feed speed of conveyor belt : n.02 speed m/min. 5 / 10 min. / max. working heigth mm. 3 / 165 volt. 380/50 weigth kgs. 800
Inv. Num. : 7681 Type: SABRE 1000 Producer: Cincinnati Milacron Generated: Parameters: Control system: HEIDENHAIN TNC 426CB X-axis travel: 1016 mm Y-axis travel: 508 mm Travel Z-axis: 558 mm
CNC lathe Okuma LU 3000 M2SC 1000 / Demonstration machine Control: OSP-P300LA Spindle hours: 50 h Turning length: 1,000 mm Turning diameter: 340 mm Speed: 5 - 5,000 rpm Tool: VDI 40 2 Tool Turrets A-turret: 12 tool positions / all positions driven B-turret: 8 tool positions Tailstock Conveyor 3-jaw chuck Kitagawa B210 Touchsetter One Touch IGF Handwheel on the control panel
Stock number: 3904 PROCESSING Manufacturer: BRIDGEPORT, Type: VMC 1000 30 Machine NO.: 822918, Year of manufacture: 2002 Specifications: Table size 1150 x 580 mm Large table load 800 kg Longitudinal movement (X) 1020 mm Transverse movement (Y) 510 mm Vertical movement (Z) 500 mm Spindle cone ISO 40 Spindle speeds 6000 rpm Total power 25 KVA Tool changer 30 places Control Heidenhain Fabr. Accessories: Chip conveyance. Length: 2200 mm, Height: 2800 mm, Width: 3200 mm, Weight: 4400 kg
grinding diameter: 350 mm grinding length: 1000 mm centre height: 175 mm total power requirement: kW weight of the machine ca.: 3,5 t dimensions of the machine ca.: m Machine completely overhauled with 12 months warranty Mechanically and optically like new Photo from Kellenberger brochure Fanuc 21i control -Grinding head UR 1-2-3 external/internal/plan -Axis automatic 1° Hirth serration -Active longitudinal positioning KEL-POS Movomatic -Semi-automatic balancing device KEL-BALANCE -Grinding wheel equipment left 400mm diameter -Grinding wheel equipment right 300mm diameter -Internal grinding unit with belt drive -Tailstock with micro-adjustment -fine adjustment upper table -Paper belt filter SBP4 240l The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 4 EW 20° 4GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Used LOOS DF 1000 steam boiler. Technical parameters: "WEM" type water treatment module water preparation module type "WSM-T 2.0" LOOS-DAMPFFIX steam generator type "DF 100010", new: 2006 total volume 110l max pressure 13Bar max temp 195 degrees Celsius 2,000L fuel oil tanks complete steam reduction station 10bar/4bar hot water preparation station with a 400l tank copper coil water treatment system
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 5 EW 20° 3GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 3,75 EW20° 3GG Cubitron red from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 3,75 EW20° 3GG Cubitron blue from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 5,75 EW 22° 3GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 3 EW20° 4GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 2,5 EW20° 3GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 5,5 EW 20° 3GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 2,54 EW20° 3GG Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 145 mm diameter / bore of grinding wheel: 300 mm Flange taper: Reishauer 0 grinding wheel size: 300x145x160 mm Beam flange (machine type Reishauer RZ 400/800/1000) + including grinding disc T1SP 300x145x160 M 6,064787 EW 21,619° 3GG Cubitron Cubitron from the company 3M Ceramic grinding discs for tooth flank grinding - 145 mm wide Dimensions according to machine type Reishauer Profiling according to specification module m, running speed gg, pressure angle EW Advantages: - Grinding burn risk is close to zero - Up to 50% shorter sanding times - 2-fold reduction in dressing effort - Twice the service life of grinding discs - Continuous, consistent sanding performance - Significantly higher sanding parameters than with standard tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
maximum number of results exceeded
please refine your search
