filler and capper used for sale

Net weight= 31 kg,

Machine is in good working condition.

300 lit, good condition

Machine is in good condition.

A cutting and winding machine Olbricht is available. Documentation available. An on-site inspection is possible.

A fully automatic vertical form-fill-seal machine Hassia is available. Packaging materials: laminates/paper films/monofilms, max. bag width: 600mm, max. bag length: 1100mm, max. film width: 1240mm, max. film roll diameter: 600mm, cycle performance (continuous operation): 40 cycles/min, heat-sealing temperature: 92°C. An on-site inspection is possible.

Laska Bowl Cutter KU 80 litres, with black bowl, in function

Vemag servo crimper in very good condition incl. accessories

Annpona Cutter PB 125-990, with Black Bowl, in Function

Fuel: natural gas (NG), engine: HMG, space heating unit with CHP: yes, condensing boiler: no, additional heating unit: no, low-temperature boiler: no, B11 boiler: no, combi unit: no. Rated heat input P: 88kW, annual efficiency of the space heating system η: 136%, energy efficiency class: A, usable heat output at rated heat input with additional heater switched off/on: 87.9kW, thermal efficiency at rated heat input with additional heater switched off/on: 57.5%, electrical efficiency at the heat output of the space heating unit with CHP with additional heater switched off/on: 33.5%, auxiliary power consumption at full load/part load el: 1.132kW, in standby mode P SB: 0.06kW, standby heat loss P stby: 0.442kW, annual energy consumption Q HE: 1345kWh, sound power level indoors L WA: 72dB, operating hours: 42,892h. Water was detected in the oil circuit, the unit has an oil-related fault desp ...

Max. load capacity: 2t, tilting angle: 180°, voltage: 400V, connected load: 4.25kW, compressed air connection: 6bar, CE marking: available. Tilting mechanism: chain-driven with large drive sprocket, hydraulically assisted for safe and controlled tilting process, designed for complete turning of containers (180°). Receiving container: yellow container, specially secured with retaining brackets and locks. Operation: electrically controlled with safety interlock. With documentation. An on-site inspection is possible.

Pester PEWO-fold 1 Compact overwrapping machine for single cartons and carton collations in OPP-, PVC-, PE-materials, foil width from 90 mm to 230 mm, film thickness from 0.015 mm to 0.050 mm, maximum reell diameter 350 mm, reel core diameter 76 mm, size range min. 60 x 60 x 20 mm, max. 400 x 350 x 140 mm, carton infeed with turning star (turns the cartons by 90°), machine controlled using ELAU PacDrive C400, electrical connection 3x400V, V+N+PE/50Hz, power consumption 5.2 kW, current consumption 12.5 A, Operating pressure 4 bar, infeed/outfeed height approx. 900-950 mm, output infeed conveyor up to 150 cartons/min., output up to 60 cycles/collations per minute, machine floor space approx. 2970 x 1600 mm (LxW), machine height approx. 2150 mm, machine net weight approx. 1800 kg.

: 0554 mm : 370 mm : 2000 mm : 280 mm : 104 mm : 11 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 0390 mm : 240 mm : 1250 mm : 190 mm : 54 mm : 5,5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ALPINA TIPPER TIE SW 330 CUTTER AS NEW

Key data: 250 KW

MAN gas engine is available with very low hours. Type: E2842E312 Scope of supply: CHP Gas line Control Panel Exhaust gas cooler Enclosed silenced container

Width 34 cm Year of construction 2000 electric punching and binding machine Electric Punching - Manual Tying Split 3:1 Table model Delivery date: short-term Price on request. We supply and install worldwide.

A Mazak CNC 5-axis turning and milling center with counter spindle is available. Swing diameter: 820mm, machining diameter: 820mm, machining length: 1500mm, max. workpiece weight in chuck/between centers: 650kg/150kg, main spindle speed: 1600rpm, spindle bore: 185mm, power: 30kW/40kW, tailstock force: 15kN, quill stroke: 1466mm, tool holder: BT50, spindle speed: 10000rpm, travel X/Y/Z: 870mm/500mm/1600mm, rapid traverse: 40m/min. Machine dimensions X/Y/Z: approx. 6500mm/3700mm/3200mm, weight: approx. 26000kg, control: Mazatrol Matrix. Documentation available. An on-site inspection is possible. The machine is located in China.

Key data: 165 mm, 330 mm, 2800 U/min

WEILER Condor lead and pull spindle lathe (overhauled) Circumferential diameter over bed 300 mm Center width 800 mm Turning diameter over carriage 170 mm Gr. workpiece weight between the tips 100 kg Bed width 240 mm Spindle bore 38 mm Spindle speeds 24 - 2800 rpm Spindle motor 3 KW Z-travel 800 mm X-travel 170 mm Z1-travel 100 mm Lead screw diameter 24 mm Thread pitches: 35 Metric 0.35 - 12 mm 40 Witworth 2 - 45 Gg / " 25 Module 0.2 - 4 Module 32 Diametrical Pitch 5 - 90 D.P. Tailstock quill stroke 110 mm Tailstock quill diameter 50 mm Tailstock quill cone 3 MK 2-axis digital display 3-jaw chuck Multifix holder B with 8 cassettes Rotating grain tip Tailstock Thread Device: Metric, Witworth, Module, Diametral Pitch Geometrically outdated!

Make: Colchester Type / Model: Student Center width: 500 mm Passage: 42 mm Tip height: 175 mm Turning diameter over bed: 350 mm over slides: 200 mm Speed range: 34 to 1,500 mm Feed lengthwise: flat: 0.04 to 0.25 mm/rev Connection: 1.1 / 2.2 kW Accessories: Steel holder, 3-jaw chuck, 4 jaw chucks, steel bracket Weight: approx. 800 kg Dimensions: 1,550 x 900 x 1,200 mm

Tip height: 175 mm Center width: 800 mm Circumferential diameter over bed: 350 mm Circumferential diameter over support: 310 mm Spindle bore: 46 mm Speed range: 25 - 2000 rpm With digital display

Glass and drying plant Lisec type VHW-20/6 Specifications: • Glass thickness (mm): up to 30 • Glass height (mm): up to 2000 • Cleaning brushes: 4 front and 4 rear

Ultrasonic Banding Machine ATS US 2100 AB; tested and maintained by ATS Germany support; Belt width 75mm; Frame 430x205mm; 2-fold print mark control for printed material; fixed strap length adjustable; Arc air; suitable for paper or foil. Ultra sonic banding machine ATS US 2100 AB; checked by the support of ATS Germany; band width 75mm; frame 430x205mm; Double Print Mark Reader; fix band lenght possible; airing for the frame; used for paper or foil.

Glass thickness: 3-19mm, glass dimensions: 140-2000mm, speed: 0.1-10m/min, installed power: 61kVA (49kW, 86.4A, 400V), max. glass weight: 6170kg, working height: 920mm, max. opening speed: 30m/min, with transfer module Bottero TRANSFER 500P, weight: 1t. An on-site inspection is possible.

WITH TRIMMER p/n: 2654000N SN: 060900759 Format: up to SRA

Two drying and heating ovens Binder for laboratory use are available. 1) Binder ED 400, usable volume: 400L, internal dimensions X/Y/Z: 1000mm/800mm/520mm, levels: 2, max. load per level: 35kg, max. total load: 90kg, recommended wall clearance rear/side: 160mm/100mm, max. temperature variation: +/-3K, max. temperature: 300°C, power: 3.4kW, machine dimensions X/Y/Z: approx. 1250mm/1050mm/800mm, weight: approx. 125kg. 2) Binder KBF 115, usable volume: 100L, max. temperature: 100°C, power: 1.7kW. Documentation available. An on-site inspection is possible.

For measuring polygons with an odd number of sides. The technical data is provided by the manufacturer or operator and is therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then get in touch with us. You can find further offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 410 mm y-travel: 310 mm z-travel: 400 mm table-size: 700 x 280 mm control: Heidenhain TNC 145 tool adaptor: SK40 turning speed range: 40- 2.000 U/min rapid speed: 1,5 m/min feed speeds: 1500 mm/min power requirement: 2.2 kW quill stroke: 63 mm weight: 1,3 t total power requirement: 2,2 kW weight of the machine ca.: 1,5 t dimensions: 1,4 x 2,1 x 2,0 m Features: - New TFT screen - Coolant system - Hydraulic tool clamping - Milling head with spindle sleeve - Documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tip height: 195 mm Center width: 1250 mm large recirculating Ø over bed/support slide: 400/265 mm Spindle Holder/Bore: Camlock D1-6"/54 mm Tailstock quill taper: MK 5 Spindle speeds infinitely variable in 3 groups: 0 - 2500 rpm Feeds longitudinal: 0.018 - 1.2 mm Feed plan: 1/2 of the longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 Inch Thread: 2 - 56 Gg/" 20 module threads: 0.2 - 3.5 module 20 Diametrical Pitch Threads: 8 - 56 DP electr. Connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm

Specifications: Tip height: 140 mm Turning length: 500 mm Accessories (included): Lunette Multifix "A" Collets 0.5 – 24 mm Milling device (Y-axis) 3-jaw chuck 125 mm Cs Urh Axexlr Hkszorh Face Plate 260 mm Running tip Chuck Die stock 4-jaw chuck Coolant pump Instruction manual (German)

A wood dust extraction and filtration system Krämer for saw lines is available. 1) Wood dust extraction unit Krämer VKA-P 100/650/55, air volume flow: 27000m³/h, pressure increase: 3800Pa, motor power: 55kW, V-belt length: 3550mm. 2) Filtration unit Krämer GFS Shake 160/25/250, filtration capacity: 30000m³/h, filter material: polyester needle felt, material discharge: TFS40/10/1.1. 3) Fan Krämer VFM-R 45/250/3, air volume flow: 3000m³/h, pressure increase: 2500Pa, motor power: 3kW. 4) Fan Krämer VFM-P 42/200/4, air volume flow: 2500m³/h, pressure increase: 3000Pa, motor power: 4kW. 5) Separator tank/filter hopper Krämer. 6/7) 2x axial fans. Including pipes and peripheral equipment. The motor flange on the discharge motor is defective. Documentation available. An on-site inspection is possible.

Tube filling and sealing machine with hot air unit for filling and sealing PE and laminate tubes, Output depending on tube size, filling volume and viscosity of the filling product approx. 15-20 cycles / min. incl. cooling unit

SPINDEL 115 , ISO 50 , X,Y,Z - 2000 DRO TABLE 1400 X 1600

Jac Bread Gate Bread cutter 9mm cutting thickness speedswitch with protective cover front and back Emergency stop switch 380V 50Hz on casters Height: 130cm Width: 60cm Depth: 60cm

Key data: 264 KW, 450 kVA, 400 V

Jenbacher Gas-CHP J 208 GS-C Gas electricity and heat generator from 1994 with 67,000 operating hours, CHP unit with control and silencer, additional parts. 1 available 253 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Stamford HC 534C2, 450 KVA Manufacturer: Jenbacher Model: J 208 GS-C Type: Gas CHP Engine Serial Number: 21619 Engine power [KW]: 264 Electrical power [KWel]: 253 Speed [1/min]: 1,500 Year of Make: 1994 Hours: 67,000 Weight unit [kg]: 5,000 Dimensions LxWxH [cm]: 450 x 150 x 195 AC Generator Stamford HC 534C2 Manufacturer: Stamford Model No.: HC 534C2 Type: AC Synchronous Generator Serial number: 49059/2 Power [KVA]: 450 Voltage [V]: 231 / 400 Frequency [Hz]: 50 Current [A]: 649 Speed [1/min]: 1,500 Year of Make: 1994

Treif Discus Circular Knife Machine Type: Discus 400 digital control Circular knife Cutting width adjustable from 4mm to 18mm 400V 50Hz Stainless steel cladding Weight approx. 200 kg Operating voltage 400 volts Control voltage 24V/DC V AC Nominal power 0.9 kW Circular knife with Teflon coating Height: 110cm Width: 80cm Depth: 70cm

Used head machine GULLIVER, type: IRIS 20 Special R -In very good condition / new parts- Dough-friendly, automatically operating dough dividing machine for the production of rustic rolls and breads in various shapes and Sizes. Square, triangular, diamonds, trapezoids and also ciabatta. - extra long inlay belt, for more dough - 2 new Mehler - Incl. 4 cutting rollers - Portioning and shaping of the dough by, easily and quickly replaceable, knife rollers - Best choice for processing doughs with high dough yield - This means that there is sufficient dough volume after freezing or interrupting proofing - Very space-saving due to foldable straps - Frame in stainless steel - Stepless adjustment of the speed - Display can be swivelled incl. several programs - Machine cleaned - Very good technical condition - Ready for immediate use Technical data: -El. Connection: 380 V, 5 ...

Key data: 2000 KW, 2500 kVA, 400 V

2MW Cummins QSV91 available complete with control panel, gas line, heat exchanger, log books and maintenance manuals etc.

bore capacity in steel (diameter): 45 mm quill stroke: 125 mm : 560 mm : 230 mm table surface area: 800 x 240 mm spindle turning speed range: 75 - 3200 U/min max. milling cutter diameter: 80 mm spindle taper: ISO 30 max. distance between table and spindle-nose: 460 mm throat: 230 mm connected load frequency: 400 V total power requirement: 1,5 kW weight of the machine ca.: 580 Kg dimensions of the machine ca.: 1,2 x 1,0 x 2,1 m Equipment: All axes with 3-digital display. Quill travel has separate digit display. Automatic feed in X-axis and quill. Motorized Z-axis. tapping device. coolant system. machine base. Collet set, SK tool holder. Further machine accessories in box. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40 mm throat: 275 mm bore stroke: 120 mm spindle taper: MK 4 turning speed range: 75 - 3200 U/min : 190 mm : 490 mm table surface area: 730 x 210 mm connected load frequency: 400 V boring feeds:: 0,1 - 0,18 - 0,26 mm/U total power requirement: 1,1/1,5 kW weight of the machine ca.: 0,35 t dimensions of the machine ca.: 0,8 x 0,75 x 1,85 m Drilling and milling machine - Cross Support - Cabinet - Swivel spindle head left / right 90 ° - Feed via hand crank The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 75 KW, 112 kVA, 400 V

Buderus Gas CHP EN 70 MAN E0836 E302 Gas electricity and heat generator from 2014 with 81,648 operating hours. 1 available 70 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Leroy Somer LSA 44.2 S7/4P, 112 KVA Manufacturer: Buderus Model No.: EN 70 Type: Gas CHP Engine: MAN E0836 E302 Serial Number: 100006776 Power [KW]: 75 Year of Make: 2014 Hours: 81,648 AC Generator Leroy Somer LSA 44.2S7/4P Manufacturer: Leroy Somer Model: LSA 44.2S7 C 6S/4 Type: AC Synchronous Generator Serial number: 30692/5 Power [KVA]: 112 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 162 Speed [1/min]: 1,500 Year of Make: 2014 Weight [kg]: 440

Membranpresse modell FISMA 210 (ITALIEN) Arbeitsgröße: mm 2100 x 1200 Öffnung mm 500 Arbeitshöhe mm 250 Öffnen und Schließen des Deckels mit vertikalen Pneumatikkolben Diese Presse eignet sich zum Furnieren von Formteilen wie Fensterflügelrahmen und gebogenen Teilen Oberheizung mit Heißluft Beheizung der Unterseite mit Heißluft Verbrauch approx. 9 kWt Arbeitszyklus: approx. 10 Min. Kompletter Kompressor zum Anheben der Abdeckung und unter der Abdeckung Verarbeitungsvorvakuum einstellbar bis 6,5 atm

Tip height: 355 mm Center width: 3000 mm large circulation Ø over bed/recess/bed slide: 715/790/520 mm Spindle bore: 86 mm Spindle holder according to DIN 55027: Gr. 11 Tailstock quill taper: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/flat: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitwort Thread: 2 - 28 Gg 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 Diametrical Pitch Threads: 8 - 112 DP Drive motor, pole-switchable: 380 V, 7/11 kW Weight approx.: 7 t Approx. space requirement: 6000 x 2300 mm

A vertical form fill and seal packaging machine Goglio for bulk materials including a vibrating chute scale with two chutes is available. Weighing range min./max.: 300g/3000g, accuracy: +/-0.3%, load cell type: HBM PW2 C3/18, max. load: 18kg, scale type: GL 111, packaging dimensions for 1000g: 130mm/80mm/400mm. Machine dimensions X/Y/Z: approx. 2300mm/3000mm/3500mm, weight: approx. 2800kg, control: IBM 7542 industrial computer. The machine is defective. Documentation available. An on-site inspection is possible.

AUTOMATIC SCREENCHANGER, number of screens: 2, total filter area: 1.342 cm2 cleaned by 6 scrapers, for the separation of soft contaminants such as paper, wood, aluminium, copper, foreign polymers, etc. from contaminated plastic melt., For rigid and soft PP max 30 MFI gr/10, 1.400 kg/h max moisture 3%, screening at 250 my., Scraper disc and scraper ensure remarkable efficiency thanks to their innovative geometry and the directly connected discharge channels. Contaminants are lifted from the screen immediately and forwarded to the coaxial discharge screw. The contaminants are removed under control and with a minimum of melt via this optimised discharge system., The scraper and discharge screw speeds are controlled fully automatically., - fast removal of contaminants through self-cleaning filter system with rotating scraper for screen cleaning, - high separation capacity and lowest melt los ...

A fully automatic high-vacuum rotary filling and capping machine Alwid for spirits is available. Filling stations: 48, filling valve diameter: 14mm, capper type: Alwid Favorit-PP, capping heads: 10, closure types: PP28/PP28x44/PP31.5 deep, min. working height: 1150mm, bottle volume: 0.7l, bottle types: rectangular glass bottles/vodka bottles/long-neck bottles, filling capacity according to documentation: 18000bph, effective filling capacity: approx. 12000bph, weight: approx. 6500kg, operating hours: approx. 14000h. Without sorting unit and chutes. The vacuum pump probably needs descaling. The deviation between the documented and actual filling capacity per hour is due to foam formation during the filling process, which significantly reduces performance. Documentation available. An on-site inspection is possible.

turning diameter over bed: 330 mm turning dia. in gap: 400 mm turning length: 600 mm centre distance: 750 mm spindle turning speed range: 20 - 1000 U/min spindle bore: 25 mm 3-jaw chuck: Röhm, Ø 200 mm dimensions of the machine ca.: 2000 x 800 x 1500 mm weight of the machine ca.: 1200 kg Fixed bezel Turning bezel Turning center point Three-jaw chuck Röhm, Ø 200 mm, incl. inner and outer jaws Quick-change tool holder Original Multifix size B with 2 change holders Spindle brake Tailstock quill MK3 Machine feet Lathe chuck guard Chip guard Work light The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cutter Manufacturer: Kilia Stainless steel Capacity of the bowl: 50 liters 6 knives

sheet width: 750 mm plate length: 1250 mm plate thickness: 4 mm table surface area: 1600 x 1050 mm no. of strokes: 180 Hub/min max. punching diameter: 105 mm punching pressure: 25 t total power requirement: 4,0 kW weight of the machine ca.: 1,8 t dimensions: 1,9 x 1,9 x 1,7 m Punching and nibbling machine - Digital readout for X and Y axis - Tool cabinet with tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cutter Manufacturer: Krämer Grebe Wetter Stainless steel Capacity: 65 liters 2 knife speeds 6 knives Power: 25kW