fas used for sale

sheet width: 2040 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 1,50 t dimensions of the machine ca.: m Motorized upper beam adjustment via foot switch Goatfoot bills The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1020 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 0,65 t dimensions of the machine ca.: m Upper beam can be swung out Bending angle adjustable via potentiometer Lifting height can be preselected via scale Manual and automatic bending mode possible The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2040 mm plate thickness: 3,00 mm distance between columns: mm bending angle: 135 ° upper beam stroke: 350 mm engine output: 4 kW total power requirement: kW weight of the machine ca.: 2,50 t dimensions of the machine ca.: 3,20 X 1,60 X 0,90 m - with different OW rails, especially segmented tools - Footswitch - Manual operation Machine is repaired, checked, cleaned by a specialist and is then complete functioning. Test run is carried out. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2040 mm plate thickness: 3,0 mm daylight opening: mm distance between columns: 2100 mm work height max.: mm : max. 135 Grad total power requirement: 4,0 kW weight of the machine ca.: 2,2 t range L-W-H: 23,1 x 1,0 x 1,7 m Furnishing: - Bending angle preselection - Segmented tool - additional bending set - manual backgauge - Dokumentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1 mm

Type 412 – 80 / 1,75 . Specifications: Wakzen center distance 80 mm Sheet thickness 1.75 mm at 400 N/mm² Projection 315 mm

Key data: 2040 mm, 6 mm

Specifications: Roll length 2040 mm Bending capacity 6 mm at 450 N/mm² Bending capacity approx. 80% of the bending capacity Upper roll diameter 170 mm Rear roll diameter 170 mm Lower roll diameter 165 mm

FASTI guillotine shears Effective length: 1030mm Maximum sheet thickness: 2.5mm

sheet width: 2040 mm plate thickness: 2.5 mm pre-bending: 2.0 mm diameter of upper rolls: 110 mm side roll diameter: 110 mm diameter of lower rolls: 110 mm speed: 6.0 m/min voltage: 400 V total power requirement: 1.5 kW weight of the machine ca.: 1250 kg range L-W-H: 3020 x 670 x 1010 mm Furnishing: - robust electro-mechanical three-roller drive - Driven by spur gear brake motor + countershaft - asymmetrical roller arrangement - electrical delivery of the rear roller with automatic electrical switch-off Setting min./max. travel distance possible - Rotatable control panel, front right - swing-out top roller, with folding bearing - Conical bending device - freely movable double foot switch Right/left rotation of the rollers - Manual delivery of the bottom roller using a handwheel with analogue position display - User manual (PDF) Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/ ...

sheet width: 2540 mm plate thickness: 2.50 mm distance between columns: 2600 mm daylight opening: OW 300 mm adjustment: UW 115 mm pivoting angle: 180 Grad work height max.: 910 mm back stop - adjustable: bis 690 mm voltage: 400 V total power requirement: 3.8 kW weight: 2250 kg range L-W-H: 3640 x 1750 x 1600 mm maintained condition () Furnishing: - robust electro-motive folding machine - Bending angle adjustment via electric potentiometer infinitely adjustable with digital value display - manual % automatic mode selectable - Electrical adjustment of the travel paths of the upper beam - manual lower beam adjustment up to 115 mm - 1x set of bending tools (installed / used condition) - freely movable double foot switch - manual material back gauge, adjustable at the back Adjustment range up to max. ~ 690 mm - User manual (PDF) Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/date ...

Guillotine shears, FASTI type 506-10-2,5 Masch. Nr. 96-506-018 Year of manufacture 1996 Cutting length 1030 mm Cutting thickness 2.5 mm Working height 850 mm Drive power 4 kW Mains connection 400 volts, 50 Hz. - mechanical sheet metal hold-down - electric foot switch - simple backgauge 550 mm with handwheel adjustment - 2 support arms 550 mm - angle stop right 750 mm - protective housing SICK behind the machine - control cabinet fixed to the machine space requirement L x W x H 2150 x 1650 x 1400 mm weight 650 kg good condition; used

sheet width: 2540 mm plate thickness: 3.25 mm throat: 100 mm no. of strokes: 60.0 Hub/min back stop - adjustable: 530 mm voltage: 400 V engine output: 7.5 kW weight: 2450 kg range L-W-H: 3600 x 1000 x 1560 mm Furnishing: - robust electric motorized guillotine shears - stable, front support/work table - Front control panel - including emergency stop button - manual back gauge up to approx. 700 mm - adjustable by handwheel, with analogue mm scale display - 1x front side stops - 3x front support arms - manual cutting gap adjustment - Cut/lift confirmation by foot pedal - 1x freely movable foot switch - rear sheet metal slide - User manual (PDF) Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9325320 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1030 mm, 2 mm

Max. cutting length: 1030 mm Max. sheet thickness: 2.5 mm steel Manually adjustable back gauge up to 530 mm Cutting angle adjustment Side stop and table extension Knife sharpened Weight approx. 800 kg

sheet width: 1030 mm plate thickness: 2,50 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 0,80 t dimensions of the machine ca.: m Manually adjustable back gauge up to 530 mm Cutting angle adjustment Side stop and table extension Knife sharpened The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

NC controlled edge bending machine, manufactured by Fasti Germany type 212-20-6 - 2050 x 6 mm. Thickness of bent steel sheet (St40) 6 mm - Alu 8 mm, INOX 4 mm, bending length 2050 mm. Control of the bending angle and departures of the NC bumper. Manual and automatic operation mode. Setting the bending angle to max. 135 degrees. Electro-mechanical drive. Jaw opening 350 mm. 6 kW drive. Weight 4500 kg.

CNC controlled edge bending machine, prod. Fasti Germany type 212-30-4 - 3040 x 4 mm. Bending sheet thickness Steel(St40) 4 mm- Alu 8 mm, INOX 3 mm, bending length 3040 mm. Control of bending angle and bumper departures from CNC, programs. Setting the bending angle to max. 135 degrees. Hydraulic-mechanical drive. Jaw opening 350 mm. Drive 6 kW. Weight 4500 kg.

CNC-controlled edge bending machine, manufactured by Fasti Germany type 215-32-4 - 3240 x 4 mm. Thickness of bent steel sheet (St40) 4 mm - Alu 8 mm, INOX 3 mm, bending length 3040 mm. Control of bumper departures with CNC, programs. Setting the CNC bending angle and bending radius. Hydraulic drive. Jaw opening 350 mm. 6 kW drive. Weight 6000 kg. High sectional punches for channels. Documentation

Thickness of bent steel sheet (St40) 4 mm - Alu 8 mm, INOX 3 mm, bending length 3040 mm. Control of bumper departures with CNC, programs. Setting the CNC bending angle and bending radius. Hydraulic drive. Jaw opening 350 mm. 6 kW drive. Weight 6300 kg. High sectional punches for channels. Hydraulic punch mounting Documentation

sheet width: 2540 mm plate thickness: 3,0 mm distance between columns: 2500 mm back stop - adjustable: 1000 mm upper clamping bar adjustment: 350 mm total power requirement: 4,62 kW dimensions: 3800 x 2300 x 1750 mm weight of the machine ca.: 3050 kg - lateral protective wall - 1x dual free-moving footswitch - 1x free moving footswitch - Electrically controlled back gauge with rear sheet metal support surface - with ball rollers - incl. new hydraulic pump (value approx. 4000€) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2 mm

Max. sheet thickness: 2 mm steel Roller center spacing: 100 mm Maximum projection: 400 mm Clockwise and anticlockwise rotation via foot switch Motor with infinitely variable speed adjustment Machine in original paint Accessories on request

Key data: 1040 mm, 4 mm

Max. cutting length: 1040 mm Max. sheet thickness: 4 mm steel Manual backgauge up to 550 mm Side stop and table extensions The rear area is secured by a safety fence with light barriers Knife sharpened Instruction manual available Weight: 1600 kg

pressure: 80.0 t chamfer lenght: 2550 mm distance between columns: 2060 mm ajustment speed: 90.0 mm/sec working feed: 10.0 mm/sec return speed: 90.0 mm/sec stroke: 140 mm work height max.: 930 mm dayligth: 375 mm Number of working hours: ca. 1.300 h total power requirement: 8.5 kW weight: 6300 kg range L-W-H: 2830 x 1900 x 2500 mm Machine from a vocational training center (Chamber of Crafts) good / well-maintained condition with only approx. 1.300 operating hours () Furnishing: - CNC electro-hydraulic press brake - DELEM CNC control - model DA 58 Swivel control panel, front left 2D graphical programming & product display Tool & program library - CNC axis control: Y1 - Y2 - X axis + motorized crowning - electro-motorized & controlled backgauge with 2x manually movable stop fingers (R+Z axis) - manual upper tool & lower tool clamping - split upper and lower tools - 2x stable, front  ...

sheet width: 1020 mm plate thickness: 1,25 mm pre-bending: 1 mm roll diameter: 55 mm weight of the machine ca.: 180 kg dimensions of the machine ca.: 1,5 x 0,5 m Manual plate bending machine with asymmetrical roller arrangement, rollers made of material 70 kg/mm² strength, adjustment of the lower rollers with eccentric infeed, rear roller with handwheel infinitely adjustable via worm gear, rear roller inclination for conical rounds, folding groove at the top and wire insert grooves at the bottom. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1040 mm plate thickness: 4,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 1,60 t dimensions of the machine ca.: m Manual backgauge up to 550 mm Side stop and table extensions The rear area is protected by a protective fence with light barriers Knife sharpened Operating instructions available The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2040 mm plate thickness: 1,25 mm pre-bending: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Right and left rotation via foot switch 3-roller drive Safety cable switch Conical rounding possible The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width - max.: 2035 mm plate thickness: 6.0 mm ST plate thickness: 4.0 mm VA plate thickness: 8.0 mm ALU number of strokes - loaded: 20 Hübe/min cutting angle: 1.7 ° work height max.: 900 mm Number of working hours: 1.450 h Control: LENORD total power requirement: 11.0 kW weight of the machine ca.: 4100 kg range L-W-H: 2416 x 2250 x 1760 mm Machine from prototype construction Machine with only approx. 1.450 operating hours () Furnishing: - electro-hydraulic guillotine shears - electro-motorized backgauge with NC control unit (Lenord + Bauer) - electrical cutting length limitation - manual cutting gap adjustment - 1x stable side stop, with scale and tilting cam - 2x front support arms - 1x freely movable foot switch - Operating instructions (PDF) + circuit diagram Special accessories included: - pneumatic sheet metal holding device for thin sheet metal cuts Machine link: http: ...

sheet width: 3000 mm plate thickness: 3 mm weight of the machine ca.: t 3 support arms 1 angle stop pneumatic hold-down device Backgauge to be operated by hand The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max. sheet thickness: 2 mm steel Max. blank diameter: 750 mm Motorized drive via foot switch

plate thickness: 3.0 mm throat: max. 500 mm work speed: 6.0 + 12.0 m/min distance: Walze 125 / 150 mm roll diameter: 125 mm voltage: 400 V total power requirement: 1.3 / 1.8 kW weight of the machine ca.: 1250 kg range L-W-H: 1200 x 800 x 1200 mm good condition () Furnishing: - heavy / robust beading machine - electric motor drive - Manual delivery of the top roller using a handwheel - pole-changing motor - 1x adjustable stop plate - 1x freely movable double foot switch - original instruction manual Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9475037 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1520 mm plate thickness: 4.50 mm thickness at Niro-steel: 2.25 mm distance between columns: 1600 mm stroke of upper beam: 360 mm work height max.: 900 mm adjustment: UW 100 mm total power requirement: 8.25 kW weight: 3000 kg range L-W-H: 2480 x 975 x 2080 mm Furnishing: - robust motorized folding machine 2x drive motors with 4.0 KW each - swiveling control panel, front right - Angle adjustment via electric. Potentiometers including digital actual values 1x coarse adjustment / 1x fine adjustment Adjustment 0.1 degrees - Manual & automatic mode selectable - Coding switch for opening width of the upper beam - 1x bending tool set - manual adjustment of the lower beam - 1x freely movable double foot switch - User manual (PDF) Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9355099 Machine video: https://www.youtube.com/watch?v=hC_j3FqEE ...

sheet width: 1020 mm plate thickness: 5 mm roll diameter: 110 mm weight of the machine ca.: 0,55 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width:5040 mm plate thickness:2 mm total power requirement:12 kW weight of the machine ca.:9,4 t dimensions of the machine ca.:6200× 1300 ×1900 mm working width:5000 mm control:Fasti Matik stroke of upper beam:500 mm adjustment of lower beam:u.Biegewange 80 mm control cabinet:1000 x 850 x1450 mm Documents:vorhanden

Fastening system, recessed light quick fastening, swivel bracket, 6 mounting kits TRILUX 370/1N TK No. 00120821 2065418 Material: nickel-plated brass one mounting kit includes 4 galvanized quick-mount swivel brackets New ! Dimensions ( packaging ): 300 x 150 x 80 mm

Suspension for screwing down, fixed suspension, 34 pieces VAHLE FAS 1 310 500 for track S1 ( 30 x 32 mm ) bore diameter: Ø 8.5 mm bore distance: 60 mm Material: Steel, galvanized Other quantities on request ! New ! Dimensions ( single suspension ): 84 x 40 x 35 mm Dimensions ( package ): 300 x 220 x 100 mm

Ultra nimble DIN3 backup, 630A, for power electronics. From compensation system, used, fully functional, new condition. 30 Stk.vorhanden a ´ 34. - NET Info under 0170 / 2204056 Mail to fa.raupp@t-online

-with barrel clip for grabbing standing 200-litre steel sicken barrels and 110 to 220-litre plastic L ring barrels and lid barrels -Brace with attachment to adapt to different barrel sizes -with a wide chassis to cross euro pallets or to line reception tubs for 1 to 2 barrels -Hand hydraulics for slightly lifting the barrel -Built in 2008 -Load: 300 kg -Lift range: 120-700 mm -Mass BxHxT: 830 x 1550 x 1100 mm

Very fast running agitator 0.25 KW - 3400 rpm. with aluminium propeller 300 mm Electric motor: Used electric motor 0.25 KW, 3 x 230/400 volts, n = 3,400 rpm, Weight approx. 10 kg. With motor protection plug. Wave: Precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. Rigid clutch made of aluminium. Stirring organ: Two-flyer aluminium propeller d = 300 mm.

Capacity: 0 t Number of strokes per/min: 0   Table length: 0 mm Table width: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Pressure: 30 to Stroke: (stepless) up to: 900 s/min Execution: 4 supports Table surface: Length: 425 mm Width: 350 mm Table relieving: Diameter: 85 mm Slide stroke: 10 mm slide bore diameter: 38 mm Passage between the supports: longitudinal: 455 mm Voltage 50 Hz 3x: 380 Volt Power: 5.5 kW Machine´s weight about: 1950 kg Overall dimensions machine: Length: 1500 mm Width: 1000 mm Height: 2000 mm Various accessories: Automatic feed: number: 1 Execution: rolls Electro-pneumatic clutch Security/savety device

Capacity: 0 t Number of strokes per/min: 0   Table length: 0 mm Table width: 0 mm CNC Brand: 0 CNC Model: 0 Operating hours: 34925 Technical data Pressure: 60 to Stroke: (stepless) from: 70 s/min up to: 800 s/min Execution: 4 supports Table surface: Length: 770 mm Width: 620 mm Thickness: 120 mm Table relieving: Length: 580 mm Width: 100 mm With pressing power: downside up Slide adjustment: 80 mm Stroke adjustment: from: 20 mm up to: 76 mm Slide clamping surface: Length: 700 mm Width: 456 mm Passage between the supports: longitudinal: 650 mm Lateral: 260 mm Air connect: 6 - 10 bar Voltage 50 Hz 3x: 400 Volt Total power required: 41 kVA Machine´s weight about: 7600 kg Overall dimensions machine: Length: 2600 mm Width: 2100 mm Height: 2200 mm Various accessories: Belt feeding: SOPREM Workpiece conveyor Sound insulation cabin Chip conveyor

Technical data Pressure: 32 to Stroke: (stepless) from: 80 s/min up to: 400 s/min Execution: 4 supports Table surface: Length: 420 mm Width: 380 mm Tool height: 300 mm With pressing power: upside down Slide adjustment: 50 mm Stroke adjustment: from: 6 mm up to: 50 mm slide bore diameter: 32 mm Slide clamping surface: Length: 420 mm Width: 380 mm Passage between the supports: longitudinal: 420 mm Lateral: 250 mm Voltage 50 Hz 3x: 380 Volt Machine´s weight about: 3000 kg Overall dimensions machine: Length: 1400 mm Width: 900 mm Height: 2700 mm Various accessories: Automatic feed: number: 1 Execution: collets Draw-in left Electro-pneumatic clutch Upper extractor Stock reels with electric motor

Capacity: 0 t Number of strokes per/min: 0   Table length: 0 mm Table width: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Pressure: 15 to Stroke: (stepless) from: 200 s/min up to: 500 s/min Execution: 4 supports Table surface: Length: 320 mm Width: 250 mm Thickness: 60 mm Table relieving: Length: 250 mm Width: 140 mm Cut edge: 300 mm2 Slide adjustment: 60 mm Slide stroke: 24 mm slide bore diameter: 25 mm Distance table to slide nose: max: 211 mm Passage between the supports: longitudinal: 320 mm Lateral: 170 mm Voltage 50 Hz 3x: 380 Volt Power: 3.5 HP Machine´s weight about: 1800 kg Overall dimensions machine: Length: 1350 mm Width: 850 mm Height: 1950 mm Various accessories: Automatic feed: number: 2 Execution: rolls max. stroke: 100 mm Straightening device

Key data: 15 , 500

Capacity: 15 t Number of strokes per/min: 500   Table length: 0 mm Table width: 0 mm Technical data Pressure: 15 to Stroke: (stepless) from: 200 s/min up to: 500 s/min Execution: 4 supports Table surface: Length: 320 mm Width: 250 mm Thickness: 60 mm Table relieving: Length: 250 mm Width: 140 mm Cut edge: 300 mm2 With pressing power: downside up Slide adjustment: 60 mm Slide stroke: 24 mm slide bore diameter: 25 mm Distance table to slide nose: max: 211 mm Passage between the supports: longitudinal: 320 mm Lateral: 170 mm Voltage 50 Hz 3x: 380 Volt Power: 3.5 HP Machine´s weight about: 1800 kg Various accessories: Automatic feed: number: 1

Capacity: 0 t Number of strokes per/min: 0   Table length: 0 mm Table width: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Pressure: 400 to Stroke: (stepless) from: 12 s/min up to: 40 s/min Table surface: Length: 2500 mm Width: 1500 mm Slide adjustment: 100 mm Slide stroke: 300 mm Fixed stroke: 300 mm Slide surface: Length: 2500 mm Width: 1500 mm Distance table to slide nose: max: 800 mm Passage between the supports: longitudinal: 3240 mm Lateral: 1600 mm Air connect: 5.5 bar Total installed power: 40 kW Machine´s weight about: 70000 kg Overall dimensions machine: Length: 4300 mm Width: 2500 mm Height: 7000 mm

Technical data Pressure: 30 to Stroke: (stepless) up to: 900 s/min Execution: 4 supports Table surface: Length: 425 mm Width: 350 mm Table relieving: Diameter: 85 mm Slide stroke: 10 mm slide bore diameter: 38 mm Passage between the supports: longitudinal: 455 mm Voltage 50 Hz 3x: 380 Volt Power: 5.5 kW Machine´s weight about: 1950 kg Overall dimensions machine: Length: 1500 mm Width: 1000 mm Height: 2000 mm Various accessories: Electro-pneumatic clutch Security/savety device

Welding edge former, edge former, edge chamfering machine TRUMPF chamfers of steel plates for weld seam preparation type TKF 103 Sheet thickness: 4 - 25 mm Bevel length max: 10mm Bevel angle: 30 Power: 2000 Watt Mains connection: 220 Volt, 50 Hz - equipped with guide bracket for 30 bevel angles - regrindable butt steel for high tool utilization - several impact steels - Support plates 6, 8, 10, 12, 14, 16, 18, 20, 22 mm for different material thicknesses For bevelling straight and curved edges with at least 40 mm radius. For bevelling edges on flat and curved workpieces as well as tubes with an inner diameter of at least 80 mm. Weight: 14 kg; used

Container fasteners, container securing elements -Fuses: 4 -Price: per piece -Weight: 6.5 kg/piece

Fastening clamp, 4 pieces TURCK BST-18B Ident- No. 6947214 for read/write heads Diameter: Ø 18 mm Material: plastic, PA6 Other quantities on request ! New ! Dimensions ( single mounting clamp ): 40 x 30 x 24 mm

Fastening rail, hot-dip galvanized PAGUS 320 mm Dimensions(one rail): 320 x 40 x 80 mm bores: Ø 13 mm slotted holes: Ø 13 x 92 mm New ! Dimensions: 320 x 120 x 80 mm

Fastening clamp, 25 pieces OBO BETTERMANN 823 Pg21 Article number: 1015 214 pipe diameter: Ø 28,3 mm 2x slotted hole: Ø 6.2 x 10 mm Material: steel, hot-dip galvanized material thickness: 3.0 mm Other quantities on request ! New ! dimensions ( fastening clamp ): 74 x 20 x 30 mm Dimensions ( packaging ): 152 x 107 x 80 mm

Fastening clamp, 50 pieces OBO BETTERMANN 605 Pg48 Article number: 1018 604 Pipe diameter: Ø 60 mm 2x slotted hole: Ø 5,5 x 7 mm Material: Steel, galvanized Material thickness: 1.5 mm Scope of delivery: 2 individual packages with 25 fastening clamps each Other quantities on request ! New ! Dimensions ( fastening clamp ): 98 x 58 x 17 mm Dimensions ( individual packaging ): 200 x 120 x 110 mm

Assortment fastening clamps, 210 pieces PAGUS 23 - 47 mm 50x Clamping range: Ø 47 mm Dimensions (single clamp): 63 x 47 x 14 mm 100x Clamping range: Ø 23 mm Dimensions (single clamp): 53 x 23 x 12 mm 20x Clamping range: Ø 28 mm Dimensions ( single clamp ): 61 x 28 x 14 mm 40x Clamping range: Ø 28 mm Dimensions ( single clamp ): 47 x 28 x 14 mm Material: Steel, galvanized Material thickness: 1.0 - 1.5 mm Other quantities on request ! New ! Dimensions ( packaging ): 280 x 210 x 150 mm