126,616 used machines on RESALE, but how to find them? Machine Search
Profile rail guide with one carriage DRECKSHAGE HGW25CCH 1 carriage: 70 x 58 mm profile rail: 23 x 22 x 235 mm New ! Dimensions: 235 x 70 x 36 mm
Round profile pliers TAKRAF, HEBEZEUGWERK SUHL ZR 05 ( ZR05 ) Load capacity: 500 kg Gripping range: 65 - 150 mm used, tested ! Dimensions: 350 x 180 x 250 mm Pictures similar!
Round profile pliers TAKRAF ZR1 1000 kg Gripping width: 100 /250 mm used, tested ! Dimensions: 500 x 500 x 180 mm
Section steel pliers, profile iron gripper TAKRAF ZP 1 ( ZP1 ) Load capacity: 1000 kg Gripping width: max 200 mm New ! Dimensions: 550 x 455 x 200 mm
U-profile, protective profile PAGUS for Sick C4000 80 mm Wide 4 mm galvanized steel Dimensions: 1300 x 80 x 70 mm
Contact-Duo-Profile, Row Limit Switch, Series Position Switch GELBAU 018.10 3100.0118 Profile length: 1920 mm with installation material New ! Dimensions: 2130 x 120 x 110 mm
Festo UP cross-section milling machine Clamping length / length milling profile: 200mm 7.5 KW
Profile steel shears, hand lever shears SCHERENBAU NOSSEN ScDH 10 Knife length: 180 mm round: 24 mm square: 22 mm angle: 60 x 7 mm continuous: 10 mm drivable ! used, tested ! Dimensions: 1300 x 700 x 1600 mm
Max. punching force: 700 kN Projection: 510 mm Cuts on flat steel shears 500 x 18 mm Holes e.g. 30 mm diameter in 20 mm flat bar Support table on the punching side with stops Range of tools is included in the price Weight: 3,000 kg
Specifications: 2 castors hydraulically adjustable 3 rollers driven Shaft diameter: 120 mm Roll diameter: 390 mm lateral hydr. Controlled arm correctors left and right Bending capacity square: 65 x 65 mm Bending capacity flat steel: 125 x 25 mm Motor power: 15 kW Mobile control panel with digital display Dimensions (length x width x height): approx. 1500 x 1650 x 2050 mm Weight: approx. 5 to The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.
Specifications: 2 castors hydraulically adjustable 3 rollers driven Bending moment: 48 cm/3 Roll diameter: 360 mm Main motor power: 7.5 KW Dimensions (length x width x height): approx. 2000 x 1300 x 1900 mm Weight: approx. 5.5 tons Accessories: various tools The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.
SPECIFICATIONS: Machinable tool: max. Ø 300 mm Tool length: max. 240 mm Installed power: 1.1 kW EQUIPMENT: Different types of grinding wheels
NARGESA MC 400 3-roll bending machine was built in 2015 in Spain by PRADA NARGESA, S.L. The machine, designed for precision machining of steel components, is an excellent choice for the production of, among others, gates, fences, railings and balustrades. The extremely rigid body is distinguished by the use of guide shafts and 3-axis rollers made of hardened steel, whose drive eliminates slippage during the rolling process. This solution, combined with independent, manual adjustment of the lower axes, increases overall ergonomics and productivity. The NARGESA tube and profile bending machine weighs 365 kg. Technical specifications of the NARGESA MC 400 tube and profile bending machine - number of rollers: 3 - roller diameter: 130 mm - roller rotation speed: 8 rpm - number of shafts: 2 - shaft diameter: 40 mm - shaft usable length: 80 mm - power: 1.5 kW - power supply: 3x 400 V ...
Manufacturer: Heesemann, Type: UKP 20, Year: 1990, Control: Programm, Program: yes, Axis control: yes, Work piece width min-max mm: 3, Min.-max. workpiece height in mm: 3, Sanding hight mm: yes, Schleifaggregate links : yes, Schleifaggregate rechts : 2300 , Transverse sanding units: 80, Abrasive belts at bottom: 120, Surface sanding units: 250, Year :1990
Manufacturer: Evimatic, Type: HF 82 CB, Year: 2000, Control: yes, Control: yes, Work piece width min-max mm: min. 200, Schleifaggregate rechts : 2, Unit 1 tiltable: yes, Aggregat 1 kW: ca. 1,5, Unit 2 slewable: yes, Aggregat 2 kW: ca.1,5, Number of frequency controlt belts: 2, Brushing unit: 1, Total lenght mm: 2500, Year :2000
Manufacturer: Delle Vedove, Type: Profilleistenschleifmaschine, Monting of the machine: 8 Schleifaggregate, Program: yes, Axis control: yes, Work piece width min-max mm: 10-250, Min.-max. workpiece height in mm: 6-80, Work piece length min-max mm: 300, Sanding width mm: 2500, Sanding hight mm: 80, Schleifaggregate links : 3, Schleifaggregate rechts : 3, Transverse sanding units: no, Surface sanding units: 2, Profile sanding units: 6, Monting of the machine: 8 Schleifaggregate,
Manufacturer: Reckmann, Type: Profilschleifmaschine, Year: ca.1979, Control: hand, Work piece width min-max mm: 100-300, Min.-max. workpiece height in mm: 10-60, Work piece length min-max mm: 150, Schleifaggregate rechts : 3 X Doppelkopf<CRLF>schwinschlifer, Profile sanding units: 3, Unit 1 tiltable: yes, Unit 2 slewable: yes, Unit 3 slewable: yes, Sanding belt speeds m/min: shcwingung eistellbar, Shoes electr. controlled: yes, Constant table hight: yes, Machine length: ca.4500, Year :ca.1979
Aluminium profile, 44m, only € 25/m, 90x90 L B Typ Nut 10 leicht, , used Top Special price ! For the purchase of the complete package of 44m we give you here an absolute best price. If you have a VAT number, we will gladly issue you an invoice without VAT. Top condition: The profiles were removed from a new machine that has never been in operation. Scope of delivery: 2 pieces 90x90x2900mm 4 pieces 90x90x2300mm 12 pieces 90x90x1160mm 14 pieces 90x90x1000mm
KRÜSI chalet building machine / log house production line type CM 40 Manufacturer Krüsi Maschinenbau AG CH-9105 Schönengrund AR Year of manufacture 1996 CE- marked Condition: good, technically checked and cleaned / ready for operation Functional principle Machining of timber for chalet construction / log house production The beams can be processed in one pass - cutting to length - horizontal- and vertical milling of the necks / grooves in one clamping - drilling - milling the face grooves workpiece: - Cutting height max. 200mm - Cutting width max. 250mm Robust construction in welded design. Machine (horizontal and vertical milling unit) with 4 special milling motors, with hardened and ground guides for highest machining accuracy. Carriage guided by dust-protected and preloaded ball-bearing rollers. Working range up to 200 x 250 mm. Completely re ...
Vertongen Tenoning Machine P04 year 1979 S/N 5811 in great condition from a vocational school in Finland Included with tools Automatically adjustable tenoning machine Saw unit, max cutting height 130mm, spindle 30 mm /3000rpm, 400mm diameter saw blade 2 horizontal cutter blocks diam 160mm, spindle diameter 40 mm /4500rpm 2 vertical spindles 40 mm working height 160mm, 4000rpm ( Top + bottom ) 1 vertical spindle 40mm, working height 160mm / 4000rpm all spindles are adjustable in the horizontal and vertical direction Tenoning carrige 1000x280mm Sliding guide 2400mm with manual pressure and fence Power 380V 3-phase 50Hz Extraction needs (dust collector) 2400 m3/h Weight approx.1100 kg technical information under subject for corrections
Max. punching and shearing capacity: 400 kN For example, punches 20 mm holes in 15 mm steel Shears on the flat steel shear on 120 mm to 12 mm steel Further technical data on request With an assortment of stamps and dies as desired
Volpato LS-1NR edge sander with chamfers Working height 10-100mm Aggregate system: Sanding unit 1.5kw Top chamfering unit 1.5kw Bottom chamfering unit 1.5kw Oscillation of the sanding belt mechanically Speed of the phasers adjustable by means of an inverter up to 9900r.p.m Feed speed adjustable by variator 5-30m/min Grinding unit at different angles Sanding belt length 2450x80mm
Key data: 45 mm, 130 mm, 13 mm
Punching force: 70 ton Punching capacity: Ø 28 in 20 mm steel Projection: 300 mm Scissors: 130 x 130 x 13 mm angle steel 90º 450 x 15 mm flat steel 45 mm round steel Notching: 100 x 13 mm Equipped with: - Electric length stop 1000 mm - Various accessories - 2 stations machine Country of origin: Spain Motor power: 7.5 kW Machine LxWxH: 2000 x 1200 x 2000 mm Machine weight: 2000 kg
Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/AMasch. No. 9566 Year of construction approx. 2000Punching force 80 ton. Projection 300 mmPunching up to 40 mm in 14 mm sheet metalFlat material shears 450 x 15 mmAngle steel shears 130 x 130 x 13 mm4 edge shears 45 x 45 mmRound material shears 45 mmRectangular clinker up to 12 mmMotor power 5.5 kWNeching connection 400 volts, 50 Hz stop with el. Stroke release 500 mm - work table with stop at the hole device 550 x 380
Travel X/Y/Z: 3200mm/300mm/250mm, speed: 18000rpm, motor power: 7.4kW, tool holder: SK30, tool positions: 8, tool changer: turret, materials processed: aluminum/steel (max. 5mm thick)/PVC (steel-reinforced and unreinforced), wood and plastics. Documentation available. On-site inspection is possible.
amplification -fold: 100 diameter: 560 mm workpiece height max.: mm total power requirement: kW weight of the machine ca.: 350 t dimensions of the machine ca.: 650 x 1000 x 1800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 75 (800) mm : 60 (750) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 100 x 11 (1000) mm Axis diameter: 80 mm work speed: 6,0 m/min Tool diameter: 242 mm total power requirement: 4 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 1,5 x 1,05 x 1,4 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 30 mm : 30 mm L-beam: 20 x 20 x 4 mm flat steel: 25 x 6 mm Axis diameter: 20 mm work speed: 11 U/min total power requirement: 0,2 kW weight of the machine ca.: 80 Kg dimensions of the machine ca.: 0,6 x 0,6 x 1,5 m Profile bending machine with: - Foot pedal for right/left rotation - Digital display - 1 set of standard rollers - 3 rollers are driven - Horizontal or vertical operation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 35 (600) mm : 35 (900) mm L-beam: 50 x 50 x 5 (800) mm T - beam - web outwards: 60 x 7 (600) mm Axis diameter: 50 mm work speed: 4,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,1 x 0,8 x 1,5 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 35 mm : 35 mm bar material dia. max.: 70 x 2 mm rectangle: 60 x 60 x 3 mm flat steel: 60 x 10 mm Axis diameter: 50 mm work speed: 4,3 m/min total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 0,9 x 0,95 x 1,4 m Profile bending machine with: - Foot pedal right/left rotation - Hardened special steel shafts - 1 set of standard rollers - 2 rollers are driven The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
For sale is a good used Keyence digital measurement projector of the type IM-6025. The measuring device is sold including the IM-7500 control unit. Prior sale and errors excepted.
Two old Mitutoyo and Nikon projectors are available. 1) Mitutoyo PJ321F, projection lens: 10x/20x/50x/100x, projection screen: 315mm, material: finely ground glass, rotation range: +/-360°, angle display: digital, resolution: 0.01°, contour illumination: +/-0.1%. 2) Nikon V-12, projection screen: 305mm, rotation range: 360°, lens compatibility: 10x/20x/50x/100x, resolution: +/-0.1%, max. workpiece height: 100mm, weight: approx. 80kg. On-site inspection is possible.
: 35 (800) mm : 35 (1200) mm L-beam: 50 x 50 x5 (850) mm flat steel: 60 x 10 (800) mm Axis diameter: 50 mm work speed: 4,5 m/min roll diameter -toolpieces: 155 mm total power requirement: 1,5 kW weight of the machine ca.: 0,9 Kg dimensions of the machine ca.: 0,6 x 0,9 x 1,35 m Profile bending machine with: - Foot pedal for right/left rotation - 1 set of standard rollers - 2 rollers are driven - Horizontal or vertical operation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 30 mm : 30 mm flat steel: 50 x 10 mm L-beam: mm Axis diameter: 30 mm work speed: 6,0 U/min roll diameter -toolpieces: 132 mm total power requirement: 0,75 kW weight of the machine ca.: 0,25 Kg dimensions of the machine ca.: 0,6 x 0,8 x 1,3 m Profile bending machine with: - 1 set of standard rollers - 2 rollers are driven - Horizontal or vertical operation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Very few working hours: approx. 200 h Technical and visual condition: very good+ Pictures attached Price: 16.000 EUR net ExW Heavy welded steel construction Horizontal and vertical work possibility All three rollers driven by hydraulic motor and planetary gear Hardened rolls Hydraulic delivery via two lower rollers Lateral mechanical straightening rollers, infinitely adjustable Separate control panel with foot control and 2 digital displays Bending performances profile type optional Explanations for bending performance, profile type optional The performance data apply to material with a max. Yield strength of 24kg / mm². Bending power at VA: factor 0.7 Bending performances profile type standard Square material dimensions [1] 45 mm Square material min. bending Ø [1] 500 mm Square material dimensions [2] 15 mm Square material min. bending Ø [2] 380 mm Flat material l ...
Manufacturer: LASM Model: LS-2N1A Year of Manufacture: 2001 Type of Machine : profile sander with 2 sanding belts and one abrasive wheel station Technical Specifications: - Max workpiece thickness: 80 mm - Min workpiece length: 100 mm - Overall Dimensions: 4400 × 1400 × 1900 mm - Net Weight: 1200 kg Sanding Belt Units (x2): - Two-speed motor - Unit articulation: 135° - Belt dimensions: 80 × 2450 mm - Belt speed: 7–14 m/sec - Pneumatic belt tensioning - Mechanical oscillation - Pad movement timer (exit/return) - Air blowing system (belt cooling & cleaning) Abrasive Wheel Unit (x1): - Single-speed motor: 2 HP - Unit articulation: 180° - Max wheel diameter: 220 mm - Shaft motor diameter: 30 mm - Feed track speed: 5–25 m/min (variable) Find more here - / Contact us at -
GREINER double-strand calibration table getCAL 11.2-5P/4Z - DUAL A (2008) Clamping table (L / W / H): 2 x 11,170 / 2 x 380 / 940 – 1,040 mm Rail spacing: 2 x 320 mm Center Distance Dual: 500 mm Clamping width (max.): 400 mm Height adjustment: 100 mm Side adjustment: (+/-) 15 mm Longitudinal adjustment: 750 mm Tilt adjustment: (+/-) 10 mm 5 vacuum pumps á 4.6 kW incl. 50 ABA 1/2'' vacuum connections 4 cyclone pumps á 1.1 kW Dimensions (L x W x H): 11,200 x 1,580 x 1,200 mm incl. calibration & water tanks GREINER Double Strand Fume/Saw Combination getCOM 30/9-235-S/500 (YOC 2008) Max. profile dimensions (W x H): 235 x 140 (per side) Contact length tracks: 2 x 2,300 mm Number of cleats: 2 x 55 pcs. Lug width: 235 mm (per side) Pull-off force max.: 30 kN (per side) Pull-off speed: 0.5 - 10 m/min Extrusion height adjustable via machine feet: 1,040 – 1,140 mm Saw ...
STEIN Maschinenbau Profile Guillotine PT1-200 For glazing beads, small profiles, main profiles and technical profiles Max. cutting width: 190 mm, max. cutting height: 120 mm Extrusion speed: up to max. 10 m/min Blade length: 600 mm Length accuracy: +/- 2 mm Knife stroke: 180 mm Cutting speed infinitely variable Pneumatic quick-change device for knives Hold-down device pneumatic Knives are preheated: 80ºC - 160ºC Cycle time: 1.5 to 4 sec. adjustable on the display Infeed side: unit for applying a protective film to the profile Control: Compact PLC Siemens S7-613C Dimensions: Height: approx. 1,900 mm, extrusion height: 1,100 mm (+/- 50 mm height adjustment) Footprint: approx. 1,450 x 800 mm (without inlet and outlet tunnel) Condition: very good, ready for use
Profile belt sanding machine, PS0 Rasprofil from Zimmermann with many accessories Sanding machine with swivel table and additional equipment for rasps. Ideal for use in model making and mould making. For precise grinding of contours. All settings with clamping lever and fine adjustment. Drive motor 400Volt, 1.1kW Table can be swivelled up to 45 degrees forwards and up to 20 degrees backwards Machine table approx. 400 x 400mm Fold-down upper extraction arm for sanding large parts. By snapping the free-standing profile rail into the upper part of the machine, a high angular accuracy can be achieved. Including three profile turning rails 15, 30 and 40mm (straight and radius) In addition, some sanding belts, see photos Three unused rasps. Suction connection 80mm Original paint, dabbed in places CE mark Very well maintained machine from prototype production in the motor ...
Max. punching force: 700 kN Projection: 510 mm Cuts on flat steel shears 500 x 18 mm Holes e.g. 30 mm diameter in 20 mm flat bar Range of tools is included in the price Weight: 3,000 kg
CONTROLS CNC controls SIEMENS SINUMERIK WORKING RANGE SURFACE GRINDING grinding length: 880 mm grinding width: 510 mm TABLE (SURFACE GRINDING) table surface (left-right): 800 mm table surface (front-back): 430 mm workpiece load (max): 800 kg MAGNETIC TABLE length: 800 mm width: 400 mm SPINDLESTOCK GRINDING SPINDLE spindle revolutions (min): 1500 /min spindle revolutions (max): 3500 /min GRINDING TOOL type of grinding tool: wheel diameter (min): 210 mm diameter (max): 400 mm borehole: diameter: 127 mm width: 100 mm ELECTRICAL SPECIFICATIONS mains power supply: 30 kVA DIMENSIONS / WEIGHTS space requirements -left/right-: 3150 mm space requirements -front/back-: 2350 mm & ...
Brand Sahinler Model: PK 35 Year of Make: 2024, Unused Capacity (Kw) 1.5 Voltage 400 Frequency (Hz) 50 Dimensions LxWxH (mm) 1000 x 750 x 1400 Weight (Kg) approx. 400 Quantity in stock 4 Made in Turkey Ø Diameter (mm) 50 Comments Unused machines for competitive prices, multiple units in stock, footpedal included
I-beam section - upend: 100 x 20 (d 2100) mm bar material dia. max.: 100 x 3 (d 3000) mm L-beam: 80x80x8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm I - beam section - flat steel: 120 x 30 (d 600) max.140b mm bar material - diameter: 60.0 (d 1000) mm tool taper: 80.0 mm oil volume: 100 Liter turning speeds: 4.2 m/min. weight: 1600 kg range L-W-H: 1240 x 1375 x 1540 mm Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - electro-hydraulic ring/profile bending machine - hydraulic bottom/side roller adjustment for extra small bending radii - bottom/side roller can be adjusted individually - 3x driven rollers - divided roller segments - digital position display of the bottom/side rollers Display with touchscreen function - hardened tool holder (42CrMo4) - machine base - 2x hydraulically adjustable side guides - ...
Haul-off for profiles, used and overhauled Manufacturer: Blake Type: 303-1600-180 Year of construction: 1995/2021 Serial-No.: 637 Contact length., effective: 1600 mm Gum pad width: 180 mm Design: smooth gum pads at the bottom and top Haul-off force: approx. 20,000 N Haul-off speed: 0.1 -5.0 m/min. Drive Motor: DC Shunt Motor Motor power: 5.0 kW Dimensions: 240 x 90 x 175 cm (LxWxH) Weight: approx. 950 kg Remark: The electrical control cabinet was renewed in 2021. The machine has been cleaned, repainted and checked for function. In addition, a new control panel as a remote control incl. 10 m long control cable.
L-beam: 40 x 5.0 (d 500) mm I - beam section - flat steel: 80 x 15 (d 700) mm I-beam section - upend: 50 x 10 (d 800) mm round material: 30.0 (d 700) mm bar material dia. max.: 60 x 2 (d 1200) mm square material: 50 x 30 x 3 mm range L-W-H: 670 x 530 x 1350 mm weight: 185 kg total power requirement: 0.75 kW Exhibition machine from 2021 with only approx. 2x operating hours Condition as NEW Special price on request Equipment: - robust electro-motorized ring/profile bending machine - horizontal and vertical work possible Machine head can be folded 90° - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conformity - Operating instructions in German The data for this ad was crea ...
maximum number of results exceeded
please refine your search
