extrude used for sale

Make: Future Tech Model: Twin Screw PET / PP / PS Extrusion Line Condition: Excellent – new after testing. Availability: Immediately Materials: PET / PP / PS (Virgin and Recycled Flake) Material Width Range: 0.18mm – 1,2mm Max Sheet Width: 1100mm Output: 1000kg/hour Main Extruder: 95mm Future Tech UV95 twin screw extruder water cooled Co-Extruder: 65mm Future tech single screw with 30kW ac motor & invertor Running from 0.18mm to 1.2mm thick PET up to 1000kg/hr. Mix of virgin, post consumer bottle flake and skeletal flake. 2 Component volumetric blending system for primary and secondary extruders. 95mm Future Tech UW95/44 twin screw extruder water cooled. 250kW ac motor with inverter drive. Triple vented with liquid ring vacuum pump system. Hydraulic screen changer, dual piston, filter dia Φ180mm, manual control. JCTimes model 275 gear pump with ac motor and  ...

Manufacturer: Future Tech Model: Single Screw PS/PP Extrusion Line Year: 2016 Condition: Excellent Availability: Immediately Materials: PS-PP grnulate Material Width Range: 0.18mm – 1,2mm Max Sheet Width: 750mm Output: 450kg/hour Main Extruder: 120mm single screw extruder air cooled 90kW ac motor & inverter Co-Extruder-1: 65mm single screw with 30kW ac motor & inverter Running from 0.18mm to 1.2mm thick PS/PP up to 450kg/hr. Mix of virgin an regranulate Vented 120 mm extruder with liquid ring vacuum pump system. Screen changers with GOODI systems. Feed block with selector plugs. 750mm wide flex lip single manifold sheet die. Max net width of the sheet is 750mm. Manual T- die. Flex bottom lip. Fixed uper lip. 1100mm wide 3 roll polishing stack with horizontal configuration ( 300mm x 450mm x 450mm diameter). Individual inverter speed drives. Max roll weight 200kG. ...

Model: Single Screw PS/PP Extrusion Line Year: 2012 Condition: Excellent Availability: Immediately Materials: PS-PP grnulate Material Width Range: 0.18mm – 1,2mm Max Sheet Width: 750mm Output: 350kg/hour Main Extruder: 105mm single screw extruder air cooled 120kW ac motor & inverter Co-Extruder-1: 65mm single screw with 30kW ac motor & inverter Co-Extruder-1: 45mm single screw with 20kW ac motor & inverter Running from 0.18mm to 1.2mm thick PS/PP up to 450kg/hr. Mix of virgin an regranulate Vented 105 mm extruder with liquid ring vacuum pump system. Screen changers with GOODI systems. Feed block with selector plugs. 750mm wide flex lip single manifold sheet die. Max net width of the sheet is 750mm. Manual T- die. Flex bottom lip. Fixed uper lip. 1100mm wide 3 roll polishing stack with horizontal configuration ( 300mm x 450mm x 450mm diameter). Individual inverter ...

Leonard monofilament yarn line with winder 160 position. Full rebuild in very good condition Construction year 1990 but many parts have changed brand new . With bicon bobbin for winder. Ready to operate. The line is COMPLETE EXTRUDER with die 2 pieces extra Hot water bath 3 set godet roller Hot oven Winder 160 bobbin 1500 plastic bobbins extra Dosing simple It is READY TO PRODUCE The line can produce PP and PE

Entire coextrusion line consisting of: - Bandera extruder 80 - 20 L / D - 60 kW, 400 V - year 1969 - variable V gearbox - Bandera extruder 80 - 20 L / D - 60 kW, 400 V - year 1965 - mechanical gearbox - 700 mm coextrusion table - Towing cutter, oven, Tecnofar exit tunnel with hydraulic variators - Omipa calender width 1000 mm with hydraulic variators - year 1976

Ghioldi extruder diam.80 low and medium density, original ALPINE 250 K/F IBC head. Oscillating towing on the frame, water-cooled towing cylinders, table width 1700mm, Cason treatment never used, automatic bubble guide, BST film aligner, bubble air replacement with IBC , air cooling with chiller, automatic spooler. Production varies according to the materials and external temperature, however, 220 kg/h can be reached. Doteco gravimetric system plus Moretto dosamaster. No. 01 new screw to be assembled, visible in operation, has worked a few days a month.

Specifications: Production line for EPE foam sheets EPE foam tube (optional; ask for the cost) Working hours 1200h, Like new, Include two changeable line for tube & sheet to one extruder L/D54, Include all auxiliaries (special pumps, spare parts, pipes e.t.c), To run immediately, Capacity 80 kg foam per hour Production: 500.000 m2 foam sheet per 20 days & 500.000 m foam tube 28 mm per 20 days Full equipment & complete without any other needs or auxiliaries Other Details: Guarantee: Without guarantee Current condition: Dismantled. Cant be seen in running condition Availability: Immediate Voltage: 90 Kw

Mixing and granulating line with twin screw extruder 2CV.70.HT/41D. PP, PA6, EPDM. Screw diameter 63, length 2800. Strand granulation, storage silo, turbo mixer, 4 weighing dispensers, injection molding machine, laboratory single screw machine. Lots of different equipment.

For sale a complete extrusion line in good condition, produced in 2004 by A + G Austria. Extruder KMD110 (Krauss Muffai) 1996 The line is designed for the production of a PVC window sill, 500mm wide, as well as a seamless panel with a width of 250mm. The appropriate extrusion tool is available. Line productivity 350kg / hour. The line allows you to process highly filled mixtures at a low cost. The set includes a screw loader. The cylinder augers after replacement have worked for 6 months

complete extrusion line for 3-layer Rolbatch film. The presented model has the catalog number 120/75 / 75-1800. The line is equipped with three extruders - ϕ120 (capacity -350 kg / h) and 2xϕ75 (capacity - 100 kg / h), screen changers, trapezoidal extrusion head, water tank, cooling unit, edge cutting device, winding devices and control system. Bolts, cylinders and long head are made of nitrided tool steel. The machine is operational, but is currently in storage and is not being produced. The most important technical data: Producer: Rolbatch Model: 120/75 / 75-1800 Sheet thickness: 0.3-0.5 mm Width:

Single screw degassing extruder CFE-699-A-04 for polymers manufactured by KELLER (USA) and KOBE STEEL (Japan) under a DUPONT license. The extruder has the following parameters: Overall dimensions of the extruder, taking into account the gearbox and motor - length 12 meters, width -2.5 meters, height -1.5 meters, the total diameter of the casing with a heating-cooling jacket is 950 mm, the diameter of the screw is 600 mm, screw length -7800 mm. The average screw speed is 22-25 rpm. The total weight of the extruder without spare parts is 40 tons. The working pressure in the casing is up to 300 bar, the working temperature of heating the melt is up to 300 degrees. The casing of the extruder is heated by high temperature oil supplied to it. The average productivity of polymers is 50-100 tons per hour. The extruder is equipped with a parallel reducer of POWER-TECH INTERNATIONAL (FOOT-JONES)  ...

Extruder is missing electronics and it is not in running condition. Barrel 30D The barrel was opened for inspection of the liners and shafts, the hydraulics function correctly. Liner 1. Feed, 2.5D good condition Liner 2. Inter, 5.0D good condition Liner 3. Inter, 5.0D good condition Liner 4. Inter, 5.0D good condition Liner 5. Inter 5.0D good condition Liner 6. Inter 2.5D good condition Liner 7. XLT Discharge 5D good condition. Feed and return lines were removed and compressed air fed into circulation blocks. All blocks were found to have good flow. Pipework is in good condition with all solenoids present. All control thermocouples and melt thermocouples are in place but could not be tested due to condition of electrics. All the heaters are in place but could not be tested due to the condition of electrics. The barrel is in very good overall condition. Shafts Al ...

Two Blow film lines CMG 55 HTM Year of production 2011 1. Single screw extruder CMG 5530 - Screw diameter 55 mm - L/D ratio 30/1 - Extruder drive – 47 kW AC - Lever type screen changer 2. Blow film die BHP 20 F D 150 mm, LDPE, gap 1,6 mm, Biflux type 3. Double flow high performance Air ring CR400 - Blower for cooling ring 5.5 kW with inverter 4. Gusseting device 5. Fixed Take-off unit 6. Single station automatic winder 7. Film width 1000 and 700 mm Blow film double flow extrusion die BHP 20 F D 150 mm, LDPE, gap 1,6 mm, Biflux type Capacity: 80-100 kg/h depend if the material, thickness and size Film width: 1000 and 700 mm

Extrusion line for blowing polymer films of type ABA, MODEL 2L800 Manufacturer RUIAN AOXIANG PACKAGING MACHINERY CO., LTD 2017 onwards Specifications 1. Film thickness: 0.01 - 0.1 mm; (Thickness: 8%) 2. Maximum film width: 800 mm 3. Recyclable materials: LDPE + CaCO3, PND + CaCO3, linear LDPE; CaCO3 content - maximum 40% 4. Maximum performance: 100 kg / h; 5. Dimensions (L x B x H): 6000 x 3700 x 6500 mm; 6. Weight: 4.5 t; 7. Main power: 70 kW; 8. Certification: CE European Compliance Certificate, SGS Independent Examination Certificate, National Compliance Certificate of China GB4455 Data sheet 1. Extruder (2 sets) 1.1 auger diameter: 55 mm 1.2 Ratio of length to diameter: 30: 1 1.3 Maximum screw rotation speed: 100 rpm. 1.4 Type of screw: mixed type, with a barrier 1.5 The material of the auger of the cylinder: 38CrMo (American certificate of protection of inventions  ...

Complete retrofitted line consisting of: Processable material: plasticized PVC composition active pay off passive pay off Bandera 4020 extruder retrofitted with Toshiba ivnerter cable and profile extrusion head 4 meter stainless steel tank double flywheel drive (interface on line with inverter) double reel winder for 600 reels

GRAVIMETRIC FEEDING AND BATCHING THROUGH INTEGRATED PRODUCTION SUPERVISION Gravimetric dosing particularly suitable for injection moulding, blow moulding machines and extruders, filling and packaging machines for granulated and powdery materials. The solid steel machine frame and the particular software allow its installation even on machines with constant and controlled vibration. The different types of construction allow the combination of 2 to 6 components, differently dosed in small amounts with normal dosing screw.

Plastic granulation line with a capacity of approximately 500 to 600 kg/h Erema rga 120 1. extruder motor - 110 kW, - controlled by an inverter 2. kW thickener engine - 90 kW, 3. screw diameter 120 mm The machine has been completely refurbished (the costs of rebuilding the machine are approximately PLN 100,000). Additionally, the following equipment was purchased for the construction of the entire line: 4. Self-cleaning filter 2x400 mm. - new 5. Thread head - new 6.Extruder 150 mm. - new 7.Granulator for cutting threads - new. 8. Sieve - new 9. Koltex dryer with feeder - new. 10.Big bag station. The price in the advertisement is for the extruder only.

EXTRUSION LINES FOR SPIRAL PE PIPES / 300/1200 Max. diameter: 1200mm Min. diameter: 300 mm Diameter pipes D 300,400,500,600,700,800.900.1000,1200.SN4 and SN8 EXTRUDER/...1 Manufacturer/ Top Industri China Model/ D.65 Year/ 2007 Serial no./ No.1234 Screw diameter/ 65 Screw L/D ratio/ 33 Output capacity/ (kg/h) 250 Main drive power/r (kW) 50 Screen changer/ (YES/NO) No Co-extrud (YES/NO) No Running hours/ DIE HEAD Manufacturer/Fabricante Top Industri China Model/Modelo K2 Year/año 2007 Serial no./ No.1234 Extrusion tools and calibration tools A total of 8 sets of tools for extrusion and calibration of a square profile CALIBRATION TANK/ YES Manufacturer/ Top Industri China Model/lo Top Industri China 6000 Year/ 2007 Serial no./ No.1111 Pipe range diameter/ square profile No Vacuum pump/ 4kw Length/ 6000 COOLING TANK/ YES Number/ 1 Manufacturer/ Top ...

The blow moulding machine ptb120d used for producing toys, drums, jerrycans, kettles, water tanks, etc, is single station with single die head, which is specially designed for 60l as maximum volume, suitable for hdpe, pe, pp, pvc, petg and other materials for blow moulding. Specifications: Max container capacity: 60 L Number of die heads: 1 Machine dimension (LWH): 865.0 meters Total weight: Ton 35 CLAMPING UNIT Clamping force: 600 KN Platen opening stroke: 880-1780 mm Platen size: 9501000 mm Max mould size: (WH) 9501600 mm Mould thickness: 900-1100 mm POWER Total power: 200 KW Fan power for screw : 0.185 KW Air pressure: 1.0 Mpa Air consumption: 1.2 M3/min Average energy consumption: 120 KW EXTRUDER UNIT Screw diameter: 120 mm Screw L/D ratio: 30:1 L/D Plasticizing capacity: 250 Kg/hour Number of heating: 5 Zone Extruder heating power: 32 KW  ...

We are selling blow molding machine Voith fisher maximum capacitity 100 Liter. We put on the machine new extruder 80mm with new gearbox, heaters and motor 37kw,also new accumulation head is instaled capacity 5 liter. Machine have new pneumatic, new electric cabinet with plc and main control unit with 15 inch touch panel. Also machine have new plc with 7 inch touch panel for wall thickness control.

Equipment for the dosage of plastic material at the loading hoppers of the extruders and the relative vacuum transport system. The equipment is branded Syncro, mod. EasyBatch M3 (Doser) and Sylink 055 BM (Vacuum conveyor). The devices are in excellent condition, purchased in 2019 and used for about two months and then removed from our system to be replaced by increased equipment and kept in our warehouse.

Line for plastic coating of metal profiles. It has HEADS FOR PLASTICING closed steel profiles with mouthpieces of dimensions 40mm x 60mm and 60mm x 60mm. Mouthpieces can be of any shape for D100mm pipes and 80x100mm profiles But you can cover any profiles. Capacity 45 kg of plastic per hour. Feed rate depends on the profiles, max 45 kg/h. year of construction 2015. Unused, still packed. Steel pipe PVC Coating production line 1 SJ55/25 single screw extruder 2 Coating Mould 3 Steel straighter pipe feeder 4 Water tank 5 Haul-off (2 claws) 6 stacker SJ55/25 single screw extruder Output capacity: max. 45kg/h Screw : Diameter of screw: Ф55mm L/D: 25/1 Material of screw: 38CrMoAl Surface treatment: Nitride processing, thickness: 0.6 ~ 0,8mm, Polishing Max. rotating speed: 50rpm Barrel: Material of Barrel: 38CrMoAlA Inner processing: Nitride with thickness: 0.6 ~ ...

SAHINLER HPK Series bending machines meet the requirements for bending profiles: rolled, extruded, extruded, drawn... whether they are steel, stainless steel, brass, aluminium... These machines provide high level performance with high precision and repeatability, consistently, for the entire duration of their use, requiring very little maintenance. This results in: structural oversizing of the parts subject to stress, the precision of the mechanical parts and the use of high quality off-the-shelf components. - set of 3 rollers made up of 12 flanges & spacers - three-way side corrector cylinders with hydraulic adjustment - 1 mobile console grouping together all the command and control devices. - 1 manometer. - Handling shackle — service keys - Use and maintenance manual in which the manufacturers EC declaration of conformity is inserted - Shaft diameter (mm): 160 - Diameter  ...

Coextrusion Blow film line 3 layers CMG 55/75/55LHE – SW 2200 TA Year of production 2018 1. Extruder A – Single screw extruder 5530/LHE - Screw diameter 55 mm - L/D ratio 30/1 - Extruder drive – 66 kW AC - Nominal output in LDPE MFI 1.0 130 kg/h - Lever type screen changer 2. Extruder B – Single screw extruder 7530/LHE - Screw diameter 75 mm - L/D ratio 30/1 - Extruder drive – 118 kW AC - Nominal output in LDPE MFI 1.0 275 kg/h - Lever type screen changer 3. Extruder C – Single screw extruder 5530/LHE - Screw diameter 55 mm - L/D ratio 30/1 - Extruder drive – 66 kW AC - Nominal output in LDPE MFI 1.0 130 kg/h - Lever type screen changer 4. 3-Layer Blow film co-extrusion die CBH500 F/3S-IBC with D 275 mm, LDPE, gap 1,6 mm 5. Internal bubble cooling system - Introduction air fan 7,5 kW with heat exchanger battery - Extraction air fan 7.5 kW - ...

Icma San Giorgio MCM/60V – 40D twin screw co-rotating extruder Mod. MCM/60V-40 D and down stream equipment High performances, intermeshing screw type for self cleaning characteristics. Screws Ø 60 mm Nominal L/D ratio 1:40 Max screw speed 300 rpm Barrel Modular design made up by 10 square-barrel sectors, each one 4 D long Barrel sectors made of LK3 nitrided steel Built-in water cooling circuit, simple construction and easy to maintain High efficiency heating system by cartridge heater Broached shaft made in special alloy brake/yield/torsion resistant Modular design Screw elements made of K 110 wear resistant steel Gear box Torque per screw shaft Nm. 1050 per each shaft Gear-ratio 4.28 : 1 Min. bearing lifetime at max. speed and motor power 20,000 working hours @ 160 bar Main A.C. motor Power applied to gearbox shafts KW 66 Speed rpm 1285 Water cooling unit  ...

Mark Two in great condition, like new with the following accessories:, Equipment:, 2x Onyx FFF filament - 800 cm³ spool, 3x Precise PLA FFF filament - 600 cm³ spool, 1x cleaning stick Precise PLA (desktop and X series), 1x carbon fiber CFF filament - 50 cm³ spool, 1x Kevlar CFF filament - 50 cm³ spool, 1x fiberglass CFF filament - 50 cm³ spool, 1x HSHT fiberglass CFF filament - 50 cm³ spool, 1x dry box for material storage Compact (desktop and X series), Net build volume (xyz): 320mm x 132mm x 154mm, resolution (z): 100µm - 200µm, nozzle diameter : FFF nozzle 0.4mm, CFF nozzle 0.9mm, extruder units: Double quick-change extruder, Printing break + restart possible: Yes, build platform: Kinematic coupling; Repeated positioning accuracy 0.01 mm, building material: Onyx, Nylon PA6, endless fibers: Carbon;Fiberglass;Kevlar;HSHT Fiberglass (High-Strength High-Temperature Fiberglass) ...

MAZZONI LB toilet block production line. New 2007. The line consists of : 1. mixer PS-256.1 2. screw conveyor T-255.1 3. extruder PL-258.1 4. cutting device (twin-bladed slicer) PX 258.1 5. cutting machine (tracked single-feed slicer) PX 256.1 6. additional production line equipped with bag dust collector FW-PARTNER-2200/N 7. additional belt conveyor for transport of difficult raw material . 8. single-coil forming head. 9. double-coil forming head. 10. COREMA thermoregulator.

AMUT PVC PIPES-PROFILES TWIN SCREW EXTRUDER, type BA 72/22, N.2 x 72 mm parallel, counter-rotating screws 22 L/D, Complete line including :, calibration desk CIemme Amut 3 mt., N.2 pumps, 35 kw drive, Vobau pull off unit max width 2.800 x 200 mm. for 650 mm.useful width, control cabinet

CIRCULAR SAW model SCM SI 400 EP CLASS with CNC-controlled 3-axis ( blade lifting, blade inclination, motorized parallel guide ) with scoring unit EASY CNC electronic control CE regulations : YES with Instruction Manual and CE declaration conditions of use: excellent volts.380/50 Electronic control: manual, semi-automatic and automatic management modes - operator interface with clear and professional graphics 7 inch "Wide screen" color display for precise cutting of furniture, custom-made furnishings, kitchens, panels, doors, frames, composite materials, aluminum and various materials Composition: Sliding carriage in extruded aluminum with large section, rigid and with closed reticular structure for maximum resistance Anodized and hardened surface for maximum wear resistance Ground prismatic guides Worktop complete with extensions, it is made entirely of cast iron ...

AMUT TWIN SCREW EXTRUDER FOR PIPES/PROFILES, Type BA92/22, constructed in 2004, parallel counter-rotating screws diam. 92 mm 22L/D, new screws and barrel, used for PVC window profiles, D.c. 59,5 kW drive, including 2 volumetric dosing units

complete production plant for shopping bags and bean handle/open mouth. System composed of: Tecom extruder 2 Flexo Stack Omat flexographic prints + Bielloni Mobert welder 2 Elba + Kmt die-cutting machines 2 Manzoni inline printing plants Semi-automatic flexible handle machine Flexloop” TECOM EXTRUDER rotating head, inverter motors consumption in operation 9kw/h Production yield 40Kg/h. Integrated castle, motorized tow adjustable in height and modified for sheds up to 4m. Mixer, dryer, automatic master doser, UV ray printing treatment. New wiring and thermoregulators. Minimum band 18cm Maximum band 80cm Bivalent screw: extrudes HD/PLT/BIO COMPOST Machine in operation MOBERT Victory 800 Bio compost ready” WELDING MACHINE Totally overhauled and updated. Change from open mouth/bean bags in one click. Inverter/PLC/Touch screen control panel. Up to 3 tracks. Min cutting l ...

NEXTROM FCL21/HS Multi-layer Cast Film Line Materials to be processed: Barrier film / Stretch film / PP film / LDPE Extruders: Number of extruders: Extruder 1: diam. 140 mm; 244 kW motor Extruder 2: diam. 140 mm; 244 kW motor Extruder 3: diam. 75 mm; 120 kW motor Extruder 4: diam. 75 mm; 120 kW motor ABB drives for the extruders 2x90mm screws for trim feeding Die: Flat die type, Cloeren, year 2016 Lip width: 2600 mm Lip gap adjustable: from xx to xxx microns Film thickness 12-35 microns Heating: 64kW + 100 pc heating elements for profile regulation Output: Up to 1000 kg/hour depending on material formulation Chill-Roller: 2700 mm wide diam. 1000mm Winder: NEXTROM Winder, fully automatic roll change  Maximum line speed 900 m/min  Reels diameter up to 500 mm  Winding width 2000 mm Accessories:  Longitudinal film cutting unit   Edge trim cutting syst ...

The most cost effective solution for extruders up to 3.000 kg/h., Very compact shape, less metal to heat up., High resistance to pressures line (up to 350 bar)., Minimum material waste due to the continuous cotamination removal., Adjustable speed of the discharge screw allows the finest handling. Continuous cleaning allows to use filters longer than traditional technologies., Pressure is kept constant all the time for a more even process, Easy maintenance: filter replacement easier and faster, without removing machine’s components. Also available with an automatic opening system that makes opening and closing lid’s operations easier, faster and safer., Double screening system : 2 x Ø 370 mm., With laser screens (from 60 to 350 µm), punched screens (from 400 to 2000 µm),, metallic mesh screens (from 230 to 10 mesh)., Bespoke screens available since they are produced in-house., Lase ...

The most cost effective solution for extruders up to 2.000 kg/h (over 2.000 kg/h, see our item [SBG800](https://www.germanplast.eu/listings/5070212-italian-fully-aut omatic-screenchanger-doctor-blade-system)), You can afford one now to improve your material quality and (your workers job), Available in Ø 400-500-600-700 mm., With laser screens (from 60 to 350 µm), punched screens (from 400 to 2000 µm),, metallic mesh screens (from 230 to 10 mesh)., Bespoke screens available since they are produced in-house., Laser and punched screens withstand wear and high temperatures.They can be cleaned in a pyrolytic oven to be re-used several times., Counter-flow cleaning system, suitable for light contamination, is used with economical metal mesh., Compact, very easy maintenance., Low material waste., Contact us with your projects details:, - Kind of material, - MFI, - Throughput rate in kg/h, -  ...

USED REGRANULATION LINE for PE PP PC PS ABS PA, throughput rate 800 kg/h, including crammed feeding unit, extruder with screw diam. 150 mm.(5.91) 33 L/D, fan cooled barrel, 352 kw drive, vacuum degassing unit, semi-automatic sliding plate screen changer (possible addition of fully automatic screen-changer), POWER PACK, Filtec under water pelletizer, water filtering unit, heat exchanging unit, centrifugal dryer, electric wiring and cabinet new in 2004, This extruder has been constructed in 1997, and we offer it reconditioned, CAPACITY: 800 kg/h, MATERIALS: PE PP PS PC ABS PA, VACUUM DEGASSING POINTS: 1, AVAILABILITY: 5-6 weeks from confirmation

AMUT BA92, Built in 2000, Twin-screw extruder with 2 Ø 92 mm screws. 22 L/D, n.2 volumetric dosing units, 59.5 kw motor, Electric cabinet and control panel, CE certification, manual and diagrams, Machine in very good conditions, Throughput with PVC profiles: approx. 250 kg/h

The line is offered TOTALLY RECONDITIONED., PREALPINA EXTRUDER 180 mm. 2 degassing points, for LDPE HDPE PP PS PC ABS EPS EPE EPS XPS..., average throughput rate 800-1.200 kg/h depending on materials and feeding rate Including: Buffer silo with agitators and feeding auger. Forced feeding unit. Extruder with 180 mm bimetallic screw 40 L/D Double vacuum degassing system a.c.355 kw a.c.drive controlled by ABB inverter Semi-automatic non-stop screen-changer with 300 mm diam. screens., FULLY AUTOMATIC NEW SCREEN-CHANGER AVAILABLE (+200 K€ +/-) hydraulic power pack Water ring pelletizing unit. Drying centrifuge., water re-circulating tank, Heat exchanging unit on gearbox group + cutting unit. Vibro-classifier., Control panel with touch screen Electric cabinets for managing the line, Constructed in 2006. Total installed power 650 kw, average used in work 420 kw User’s manuals, drawings, CE. ...

Key data: 40

Extruder 2 co-rotating screws: 40 mm Ø diam, 35 L/D, brand: Comac, motor: 37 Kw (50 hp) with variable speed drive, year: 1992. Designed to provide exceptional performance in the production of plastic materials. Its powerful 37 kW (50 hp) motor with variable speed drive ensures efficient and versatile operation. The Comac brand is synonymous with quality and durability in the industry, and this extruder is no exception. If you're looking for a reliable machine that has stood the test of time, this may be the perfect choice for your extrusion process. Contact Gester today for additional details on this Comac 2-screw co-rotating extruder and how it can improve your recycling and extrusion operations. Trust in the experience and quality we have been offering for more than three decades.

Line for extrusion of XPS polystyrene foam boards with ultra-low density 20 kg/m3 and compressive strength 250-300 kp using technology patented in Ukraine with a set of additional innovative devices. Board parameters: width up to 1200 mm, thickness up to 200 mm, length is not limited. Extruder 180/235mm L/D 28-40 manufactured by the Korean company MYUNG-IL FOAMTEC Foaming gases - CO₂, DME, HFC, HFO, propane-butane, isobutane. Pumping equipment set Capacity up to 50m3/h (1000kg/h) Weight – 60t. Line length -90m, width 6m. Power consumption – 650 kW The extruders operated for a year and a half after the plant was sold to another owner, and the rest of the time the line was in storage.

GAMMAMECCANICA EXTRUDER, for PE PP PS ABS PC PA, barrel with screw diam.90 mm., loading hopper, semi-automatic hydraulic screen-changer, hydraulic pack, strand die, cooling bath, strand pelletizer, electric cabinet, Construction year 2008, The line is offered totally reconditioned, Possible replacement of cutting system into water ring, Possible addition of fully automatic screen-changer, classifier, blender,..

Manufacturer | manufacturer: Bekum Machine Type | machine type: BM 504 Stations | stations: Single Station | Single station Year of construction | Built: 1998 Location | location: United Kingdom | Germany Clamping force | Clamping force: 110 kN Control Type | control system: Beckhoff Extruder | Extruder: S60/24D Extrusion Head | Extrusion Head: Single Head | Single head Mold dimensions mm | mold dimensions mm (A Length / length x B Width / width x C Depth / depth): 470 / 420 / 2x130 Bottle Volume Max. | bottle volume max.: max. 12 L Screen Language | monitor language: German / English | German / English Operating hours | working hours: approx. 3000 Accessories | accesories: Conveyor belts | conveyor belts Packing table | packing table Delivery Time | Delivery time: 1 - 3 weeks | 1 - 3 weeks

Key data: 40

2 Screw Extruder Co-rotating spindles 40 mm Ø diam, 44 L/D, Brand: Maris Model: TM40 MPL/D44 Variable motor: 75 Kw (100 hp) Year: 2000. 2 x 70% replacement spindles.

Key data: 65

Extruder 1 Screw 65 Ø diam, 30 L/D Brand: Flag engine: 30 KW (40 hp). With electrical panel. Reference: GT-4706

Key data: 17 mm, 40 , 1200 U/min

Kategorie / Category: Twin-screw extruder / Twin-screw extruder Nummer / Number: DE27684 Manufacturer / Manufacturer: Leistritz Typ / Type: ZSE 18 HPe Baujahr / Year: 2009 Capacity: approx. 40 - 60 kg/h Motor: 9.4 kW AC max. screw speed: 1,200 rpm Screw diameter: 2 x Ø 18.8 mm L/D: 40:1 Material: PE, PP, PS, ABS + fillers // more details: synchronous, atmospheric degassing, segmented screws and barrels // Control: MacromateXX Siemens with visualization //

EMS-95 single-screw extruder, screw diameter 90mm, throughput approx. 200 kg/h (depending on profile size and material may vary). The output width is about 127 cm. Initially purchased for the production of diffusers of all kinds (transparent, partially transparent) for office LED lighting fixtures. Installed in 2012, produced about 1.500 diffusers and has not been used since then

Reifenhauser RH 241 Single screw 50mm 25D Only extruder there is no cabinet Make an offer

Fully rebuilt by Weiler in 2018. Characteristics: Output: 2800 containers per hour Molds and tooling for 100ml IV bags/bottles (12 cavity, 12 parison) included Eurocap cap welding machine with cap elevator Including: - new fill system - new extruder drive - new parison head - hydraulic system overhaul

COMAC TWIN SCREW EXTRUDER EBC60, barrel with n. 2 x 60 mm. diam co-rotating screws, 42 L/D, NEW SCREWS, n.1 dosing unit with hopper, N.1 vacuum degassing pump, d.c.132 kw Siemens main drive 400V 50 Hz, non-stop hydraulic screenchanger with 90 mm screens (available with fully automatic screenchanger, hydraulic pack, strand die (available with water ring pelletizer), cooling bath with heat exchanging unit, strand pelletizer (available fitted with a water ring pelletizer), electric cabinet with air condititioning (for extruder, screenchanger, hydraulic pack), constructed i n 2001, The line is offered reconditioned, Possible addition of :, vertical mixer, vibro-classifier, bag filling station, etc. on separate offer, CAPACITY: 400 kg/h

FIMIC RAS 400, fully automatic screenchanger, possible setting as : continuous scraping, scraping on an Amp.threshold, mounted on extruder producing 1200 kg/h with 250 my screening, 30 kw drive, machine in good working conditions, totally reconditioned in 2020, constructed in 2007, installed power : 30

TECNOVA WATER RING PELLETIZER, Type TTC1000 vertical, Drying centrifuge with water tank and re-circulating pump, n. 1 spare pump, cyclone for granulate discharging, pulpit electric panel, now producing 1200 kg on a 160 mm extruder, Construction year 2001, Machine offered reconditioned