extr used for sale

Welding fume extraction for wall mounting, extraction unit KEMPER type 85400Fabr. No. 279092 built in 1997Volume flow rate 1700 m3/hstat. Pressure 2000 PaSuction connection 250 mmEngine power 1.5 kWNeergized connection 400 Volt, 50 Hz- Centrifugal fan- Designed for a mechanical air filter with approx. 99% separation efficiency- Main filter defective, (surcharge for new main filter, 195,-- EUR net)- Joint suction pipe 150 mm, approx. 2 meters long- Suction pipe with 3 joints and suction funnel (adapter connection to the filter housing is missing)-

Filter system - extraction system, central extraction cartridges - impulse filter VALCO type Pidclean 4NZentral welding fume extractionseries. No.: 15003 Year of construction 2003Volume flow max. 3500 m³/hFilter area 92.8 m²Differential pressure 700 PaExtraction connection at the filter inlet 250 mmExhaust air connection at the filter outlet 225 x 160 mmCompressed air requirement 4 to 6 barMotor power 5.5 kWNet connection 400 volts, 50 Hz filter control AUTEL, type Eco S6- pneumatic filter cleaning, automatic via control - 4 pieces

EXTRACTION SYSTEM HUNKELER HKU 2000 (Compact Extraction Unit)

Extruder 70 mm - 24 L/D with pipe head up to 63 mm, calibration tank 6000 mm Caterpillar extractor, saw

Roller die line consisting of:- 1 x Troester 200mm pin barrel extruder Type QSM200K-16D power roller feed, 10 rows of 8 pins, L/D ratio 16:1 Serial no. 1816/88, year 1988, With temperature regulation unit, 282kW ASEA DC variable speed motor mounted on rails (moves away from calender to clean out etc) Hydraulic sheeting head linked directly to:- 1 x Adamson 24in dia x 68in wide two roll calender, peripherally drilled rolls cross axis, bush type bearings, motorised nip adjustment with unidrive gearbox 277kW ASEA DC variable speed motor Hydraulic clamping device for extruder Set of 4 x cooling drums Dual wind up and liner applicator Chalking Unit Siemens PLC control. Complete line in excellent condition. PRICE: On request.

Troester 150mm dia PIN extruder Type: QSM150K, Serial no. 8622/80, Year of manufacture: 1980, but refurbished by Troester 2000 (new screw and barrel section) Power roller feed, L/D ratio 16:1 8 rows of 8 pins, fitted with ASEA 212kW DC variable speed motor and controls (1800rpm). Complete with controls etc and in very good condition.

1 x David Bridge 15/18\ Dump Extruder with 40\ Face x 20\ die Roller Die. Spare parts available. Screw L/D 5:1, Crammer. Length of Barrel 7ft. Right angle turning unit for product flow. 200HP DC variable speed motor

Qty. 1 Second-hand extrusion press line Mfc.: 3TC, Allen Bradley, Rexroth, Gautschi, Elhaus, Nederman, Hydrotec, Marx GmbH, Truninger, Ekatech Force: 3500 MT Built: in 1960’s Pressure: 315 bar Billet dia.: 343 mm x 900 mm (can be modified 14 x 1.0 m) Modernisation: 2011 Complete exchange of control system on press to Allen Bradley Control Logix including encoders for Ram, Container and Shear. Change of pump controls to Bosch Rexroth HS4. 2012 Complete change of hydraulic system (excluding pumps). New side cylinders and container cylinders. Safety rebuild of press and with change of PLC to Allen Bradley Control Guard Logix L72S (which is the current CPU). Change of control system of billet furnace. Complete new electrical system and integration of logic into the press PLC. Modernisation of gas burners in the furnace. 2013 Change of one of the main pumps to Bosch Rexrot ...

Kobelco Twin Screw Roller Head Extruder (horizontal type), Model TSR-330 Roller die assembly (TSR-33H005H) 38in wide x 16in dia Roller die moves away from the extruder/mixer section via hydraulic ram. driven by 102kW DC variable speed motor through Hansen reduction gearbox (on flexible coupling so roller die can move forwards/back). Twin screw dump extruder 330mm screw dia driven by 90kW DC variable speed motor through Hanson reduction gearbox. In very good condition. Previously running underneath an F270 Banbury. Complete with all controls, manuals and documentation etc.

We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information

Francis Shaw 18/22\ Dump Extruder, Crammer feed Length of Screw 9ft 6\. Reliance 400hp D.C., 1150 r.p.m., 480 volt. Large Hopper/Chute to next floor level.

1 x Werner & Pfleiderer 400mm dia dump extruder, Type: EAE400, Fabrik nr 221284, Werk nr 416295, Year: 1985, double hydraulic crammer feed, feed section 965mm wide, L/D ratio 8:1, with 235kW DC variable speed motor, Sheeting head to produce up to 1000mm wide sheet. Complete with controls and hydraulics etc.

Belts - oil separators Oil separator with KUNSTSTOFFGURT OPV - 1 / OPV - 2 This group of oil separators is recommended for industrial applications. The collection in the standard version is made of plastic without connecting traces, which is adapted to the requirements, e.g. polymer, elastomer, etc. All parameters such as performance, bandwidth, and so on are selected individually. An oil lifting height of up to 15 m is particularly useful in deep tanks, e.g. sewage treatment plants. The number after the marking (300/500/700/1000 mm) is the working length of the strip - depth from the mounting base. Complete oil separator with PU polyurethane tape. Belt color: green (standard), blue or white. Maximum liquid temperature up to 60°C. We have oil separators with a stainless steel belt INOX with a working temperature of up to 100 ° C at an additional cost. Maximum liquid temperature ...

1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included.

1 rimless hydro extractor made KRANTZ, type GLEITSCHWINGER 1500 x 600 inside basket diameter 1.500 mm inside basket height 600 mm

Used EXTRUDER twin screw (TWIN SCREW EXTRUDER) for the production of cereal flakes: Producer: PAVAN Model: TT92 Year: 2002 Dimensions: 6580 x 4150 x 3000 Weight: 2400 kg Productivity: 500 kg / h Power: Description: A twin-screw extrusion device as a result of a continuous and automatic process of a great variety of flour and cereal starches / tubers, both mixed and pure. The materials from the dispensing unit are pre-mixed using a suitable device equipped with counter-rotating blades (double shaft mixer), and then enter the mixing tank for kneading and homogenization. From the mixing tank, through a suitable screw device (forced supply), the mixture is pressed into a group of cooking cylinders in which the cylinders are heated to the desired stage, according to a predefined and automatically controlled temperature profile. compatibility of extruder screws, which are repla ...

Cat. No. 11-3247 in very good condition in AISI 304 Measurements: Diameter: 2450 mm Height: 3500 mm Weight: 2950 kg For more Information please contact us under: Phone +49(0)9353-909050 Fax: 09353-9090522, Mobile: 0171-6518248 Subject to prior sale. All prices are valid Ex-Works, excl.VAT. Freight Charges: depending on dimensions and destination.

Qty. 1 Second-hand extrusion press including (water-hydraulic system) Mfc.: Loewy - Hydropress USA Built: TBA Force: 12,000 UST Modernised: 2011 & 2014 (new PLC and control panels) Billet dia.: 14’’ – 26’’ (355.6 – 660.4 mm) Billet length: max. 65’’ (1651 mm) The press was used for the production of pipe up to 508 mm diameter and up to 50 mm wall thickness by the current owners. In 2011 the Press was partially rebuilt at which time all valves were rebuilt with new wear components, all brass was replaced for the container and rams and the loader table was rebuilt. In 2014 all new PLC Controls and the Control Pulpit were installed. Note: The water-hydraulic system is not included in the scope of supply due the system is also using for another extrusion press.

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Multiple extruders

New device incl.pre and combined filters The compact device offers many areas of application - the filters used are characterized by a long service life - the two filter cassettes separate dust, fine dust and gases - Dimensions 1197 x 600 x 790mm - Suction capacity 1250m³ / hour -400v ph 50/60Hz with red 16A CE plug - Hose connection 125mm Ø - incl. option external start / stop ( with 24V DC via 2-wire cable on the back side ) to activate via micro switch - Warranty 12 months ( filter excluded ) Typical applications : Marking laser Engraving laser Cutting lasers Options: - Suction hose in the necessary length - Connection sleeves - Suction nozzles

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

Weibert WJ-ASA Professional Extraction system Power of the motor: 4 KW Suction power: 3900 m, m³/h Chip bags: 2 x 200 l Dimensions 580 x L. B. 1300 x h 2200 mm Driving device Connector 2 x 120 mm WJ-ASA Professional Special price: NET 890,-

Iddon Cold Feed Extruder. 2.5" screw dia. 10/1 LD Ratio. Motor Size 20.4/5.5 HP

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.

Key data: 100 , 140

Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station � ...

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Brand: CFT Model: TE Series Manufacture year: 2002 Production capacity: 15 tn per hour The series has been designed to improve the already superior performance of its predecessors, the MANZINI TE. 15 and TE.30. While preserving the important characteristics of its truncated cone-shaped screen, this new design permits a rapid changeover (without removing the paddles) because the narrow end of the conical screen is at the front of the unit, beneath the cover. The series of turboextractors has a peculiar characteristic: product emulsion due to air trapped within the product. In fact, the infeed of product is located on a completely closed cover and the centrifugal action of the paddles against the conical wall produces an impingement effect in the direction of product flow that helps pomace conveyance towards the expulsion channel. Turboextractors are specifically designed for e ...

Key data: 30 , 28 , 110

Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper

According to the description below

Colour JET 2 Paint mist extraction Rated motor power: 0,75 / 2,1 kW Engine speed: 96 min 0/1,430 Air volume: 3,000 / 6,800 m ³/h Effective pressure: 400 / 500 PA Dimensions closed (W/H/D): 1,012 x 1.405 x 943 mm Folded dimensions (W/H/D): 1,897 x 1.405 x 1,166 mm Pre-and fine filter filter area: 1 m² Connection diameter: 300 mm Switch zweistuftig Compact construction, space-saving Powerful, high suction power,. low operating costs Easy maintenance, long filter life Universally applicable, variable accessories High flexibility Mobile design Suction technology with front plate system G & ALKO 19562801

Weibert SA 205 Extraction system N E U machine extraction system SA 205 400V 2.2 KW (3 HP) Flow max. 2900 m³/h 2 dust nozzle 120 mm 1.7 m² filter area 1 chip bag 300 litres Fahrbahr Weight 70 kg G & WJ-SA-205

Abegg to fan and the fan with fans Ziehl. noch nie benutzt NEW

Varnish removal spray booth 3000mmbreit2000mmhoch Suction capacity 10000 m³ air of heating register 10500 m³

Device type Mobile air purification device Make TEKA Type VIROLINE MAXI Supply voltage 1 x 230 volts Particulate pre-separator filter mat G4 Main filter Hepa filter H14 fan volume flow 1,500 m³/h Motor power 0.55 kW Mains frequency 50 Hz Design mobile air purification device Dimensions L x W x H 665 x 681 x 1,930 mm Noise level approx. 49 dB(A) Weight 167 kg Age 24 months Condition workshop-checked, like new Warranty 18 months from date of delivery Original price 2.720,00 € + VAT Complete price ex warehouse Munich 1.990,00 € + VAT The machine is located in the Wilhelm Merkle Schweisstechnik GmbH Anton-Böck-Strasse 31 81249 Munich, Germany Contact person is Mr. Manuel Maier. Of course, we ship the machine to you for 60, - € by forwarding agency throughout Germany. _____________________________________________________ ...

Suction register: Make : Wolf Built: 2004 Dimensions: 3500 x 1500 x 650 mm and 2500 x 1500 x 650 mm (approx. LxHxD) only 4 pieces left in stock In addition, we offer: Exhaust air unit with exhaust air pipe and deflector hood depending on size. Rectangular sewer pipes 1200 x 600 mm, unit price € 50,- net from location. We also have complete painting booths, drying booths and spare parts for painting systems in stock, e.g. Aggregates, lights, filter ceilings, entrance gates, roller doors, gratings, air ducts, etc. Please ask.

800 MT extrusion press 1. container size 127mm diam x 560mm lenght 2. capacity: extrusion: 800t/1000t extrusion (low tonnage) at 210kg/cm: 697M Ton Main ram forward at 210 kg/cm: 112 M Ton Main ram return at 210 kg/cm: 63 M Ton Contianer seal at 210 kg/cm: 69 M Ton Contianer open at 210 kg/cm: 94 M Ton Piercing at 210 kg/cm: 102 M Ton Mandrel return at 210 kg/cm: 63 M Ton Die slode at 210 kg/cm: 12 M Ton Stroke Main ram: 1320 mm Container: 250 mm Speed 38.0mm/sec 44.0mm/sec More information on request

BARMAG POLYESTER EXTRUSION -SPINNING LINE WITH 12 POSITION / 72 THREADLINES FOR POLYESTER POY MICROFILAMENT YARNS • MANUFACTURER : BARMAG , GERMANY • CONSISTING OF FOLLOWING EQUIPMENT : •1 EXTRUDER BARMAG 12 E 8•SPIN BEAM INCLUDING SPIN PACKS & SPIN PUMPS3,5 CC/U•SPINNERETTES 100MM DIA, BOTTOM LOADED,DESIGNED FOR HIGH COUNTS MICRO & SUPERMICRO•POLYMER MANIFOLD EXTRUDER TO SPIN BEAM•DOWTHERM MANIFOLD FOR SPINBEAM ANDPOLYMER MANIFOLD•QUENCH SYSTEM INCLUDING FINISH SYSTEM,SPINFINISH JETS BY 'KYOCERA'•WITH CONVENTIONAL QUENCHING CABINETS +EVOSEPEED & RADIAL TYPE •TAKE UP UNITS, INCLUDING:•TAKE UP SECTIONS / PLATFORMS / LADDERS•COLD GODETS, ONE PAIR PER POSITION•INTERLACE SYSTEM WITH HEBERLINE INTERMINGLING JETS•YARN SUCTION SYSTEM•12 WINDERS, BARMAG CW6-1200/66 ENDS PER CHUCK , max. dia 440mm, stroke 170 mm

Qty. 1 Second-hand extrusion press Manufacturer: Loewy Type: 4 column floating - mandrel piercing press Aprox year of manufacture: 1939 Container size (dia.): 406 & 508 mm 16" and 20" Container size (length): 1350 mm Billet size (length): 1000 mm Nominal Extrusion Force: 5000 MT Nominal Piercing Force (Max): 740 MT Mandrel arresting Force floating mandrel Stroke Main ram: 2750 mm Piercer : 1200 mm

Extruder KE 90 x 30-D for manufacturing of von TPE foam and compact profiles screw diameter: 90 mm L/D ratio 30:1 (2700mm) extruder with 11 temperature-controlled zones (electrically heated by fluids) Siemens electric drive, motor 45kW at 2500rpm year of construction 1996, machine in very good condition (preliminary used in test operations) melt application device (gear pump) double profil head (also used for extrusion-coaded framework belts) electric equipment partially available extruder mounted on movable baseplate

Extruder Petersen VAP 65

RLA 160 Extraction system Dust nozzle diameter: 160 mm Engine: 2.2 kW 400 V 50 Hz Nominal volume flow at the nozzle: 1448 m ³/h Maximum flow rate: 2400 m3/h Filter surface: 9,21 m² Dust class M Residual dust content: H3 Chip collecting volume: 2 x 165 (193) l The maximum sound pressure level: 73 dB (A) Dimensions (L x W xH): 1755 x 830 x 1654 mm Weight: 267 kg G & pieces 5131620

Nordson / Puffe Extruder Plant Ex20 -1xPS01-1xPE20-1 for melting hot melt adhesives and thermoplastics, feeding as granules. Melting capacity according to the manufacturer's specifications up to 20 litres/h (EX20) Price: 45.000, -- € plus 19% VAT (Gross price incl. VAT 53.550, -- €) EXW Manufacturer: Nordson / W. Puffe Hotmelt-Technology Model No.: Ex20 -1xPS01-1xPE20-1 Year of manufacture: 05/2006 Serial No. 226260231/001 Power: 15 kW, connection 380V three-phase current Emergency stop, traffic light, CE mark Made in Germany Compact system mounted on a stable rolling frame (H= 198 cm, W= 160 cm, D= 110 cm) consisting of Nordson extruder, gear metering pump, Lenze worm drive, control cabinet with Allen-Bradley control, graphical user interface, storage tank, operating manual. Auxiliary: Labotec Minifeed Suction Conveyor MF60 Serial No. 12-103-00669 (Owner's man ...

Industrieöfen- Fertigung und zirlguss Reparatur jeglicher Art Wartung und Einregulierung von Industriebrennern Industrieöfen für Öl, Gas oder elektrisch beheizt Umfangreichen Sortiments an Feuerfeststeinen, Feuerfestmassen, Isoliermaterialen und Gießereihilfsstoffe namhafter Hersteller. Renovierungen und Instandsetzungen von Ofenanlagen Brenner einstellungen von Ofenanlagen schoenheider Modernisierungen von Ofensteuerungen Umrüstu ng von elektrischen Öfen auf gasbeheizte Öfen Umrüstung alter Heizsysteme auf Rekuperation gienanth Öfen Verzinkungsofen Ve rgüteofen Anlassofen Industrieöfen Glühofen Ovens laboratory ovens industrial furnaces industrial furnace plants Industrial Furnaces high-temperature chamber furnaces hardening furnace anlageHärteöfen Annealing furnaces Conveyor belt Abg aswäscher Abkühlungsöfen Abwärmerückgewinnung Aluminiumgiessereimaschinen ...

Key data: 150 mm

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

Hard PVC pipe extrusion plant for tubes D28/D30/D33, consisting of: Battenfeldextruder B45-24 d, ESDE tube crosshead K 010, vacuum calibration with water bath, Graewe-band trigger BA63, Graewe Abstech-and at chamfer machine STS50, various sleeves, cores, calibrations and jaws, as well as additional tube crosshead Battenfeld RS 8-40

Used three extruders with die - head/three layer extruder from POLY TECH model HP 1800/3/100/55/55. New: 2000. 1) Head/Matrix - Slot of the die - 2,26 - Die diameter - 220 mm - Thickness 25-130 microns - Capacity 250-300 kg / hour 2) Matrix/Head - With efficient heating system (set of heaters with sensors PT/100 temperature sensors) - Three described Poly Tech extruders A) Extruder fi 100 mm L/D 30 with 150 kW motor drive . ZAMBELLO/ITALY drive gearbox TYPE RPU 280 E RPM 1400 B) Extruders fi 55 mm L/D 30 with 60 kW motor drive pcs. 2 ZAMBELLO/ITALY gearboxes TYPE RPU 180 E RPM 1400 The described extruders have a gravimetric system from DOTECO/ITALY Model GRADO IIS/GO 4100940 equipped with a metering system with computer readout on the measuring cabinet. Complete plasticizing systems including drive gears and main driv ...