engine cat type used for sale

2 knife speeds 2 mixing speeds 2 separate bowl speeds emptier With loader Auto command 3000 K yoc 2017 only 1.603 running hours 125 kW total connected power

Balance range: 1500 g Temperature range: 5° - 40° C Mains connection: 220 V, 50 Hz

Balance range: 1500 g Temperature range: 5° - 40° C Mains connection: 220 V, 50 Hz

Labeler prepared for 3x adhesive labels with hot melt (front/back/safety tab). The labeller was overhauled in 2021 by the manufacturer Gernep, including new electrics according to CE standard. The labeller is equipped for the glass type DTO80. The labeller was in operation for about 200 hours after the overhaul.

Z-kneader, Year of construction 1970, engines, bearings, gears, gearbox, electrics, overhauled around year 2022. Machine is immediately available and ready for use. Z-Kneader has an electric tilting device.

Capping heads Zalkin different closure sizes

Extraction Dedusting Nedermann Type 663 with 2 extraction arms Very good condition, straight from production!

Lift-tilt device, lifting tipper Make Itec, type 2700, year of construction 2017 for accommodating 200- and 300-litre standard loading trolleys lifting capacity: 350 kg Tipping height: 2.231mm incl. 1 standard loading trolley 3x460V 50 Hz 0,75 kW - very good condition, hardly used - was used to feed a piston filling machine - Documentation/operating instructions available Visit in Korntal-Münchingen possible

Standard Equipment's Chrome Coated Cylinder Boiled Steel Body Pressure indicator Pressure Adjustment User guide 2 Years Warranty CE

Knife sharpening machine clamping length 820mm V 380 kW 0.75

belt width 400 mm all stainless steel adjustable speed with lower and upper belt adjustable upper belt with outfeed belt mobile dimensions (l x w x h) : ± 2.200 x 800 x 1.200 mm

Ref. 443 Light table Mega steel Type 399-3 Fabr. - Order No.: 93-674 Year of construction 1993 Table size: 70 x 100 cm Table top diagonally adjustable Height infinitely adjustable motorized from 85 to 115 cm Light source: 2 fluorescent tubes

Plastic compactor Main drive 132 kW Complete system with recutting mill, fine material separation and recirculation, electrical control

VACUUM MASSAGER LUTETIA TYPE 1, WITH BUSCH PUMP TYPE:100-136 Technical description: Drum diameter: ?1000 mm Capacity: 500 liter Vacuum: 2 mbar Busch pump type: 100- 136 (Serial number:176722) Pump dimensions: 700 x 400 x 450 mm Machine dimensions: 2400 x 1300 x 1800 mm

LUTETIA VACUUM TUMBLER, TYPE: 4 Technical description: SERIAL NUMBER: 16004 Power supply: 400 V, 60 Hz CAPACITY: 1800 liter, WEIGHT: 1400 kg, WITH LUTETIA STEAM GENERATOR: type: 24 kW, serial number: 12773, year of construction: 2014, capacity: 23 liter, DIMENSIONS: 3800 mm x 2000 mm x 2050 mm. (Including Busch vacuum pump on mobile s/s frame, dimensions: 830 mm x 510 mm x 640 mm)

Press Schüco Model 290124 Type 2 Specifications: •pneumatic • Operating pressure max. (bar): 8 • Weight max. (kg): 80 • Enclosed tool: included (see photos)

Automatic hardness testing device with 4 heads Micro IRHD IRHD Type L IRHD Type N IRHD Type H The device needs gibitre software installed on the computer to work. The device consists of a stand and 4 heads

Doppstadt DW 3060K Biopower Type F - Year of construction 11/2017 - Hours 4839 - Engine MTU 490 hp - AD BLUE - Track chassis - Weight 30,000 kg -Remote control - Humidification system - Tail conveyor 7m - Overbelt magnet Machine is overhauled and immediately available

Doppstadt DW 3060 Biopower Type F - Built in 2017 - Hours 6118 - Engine MTU 490 hp - AD BLUE - Weight 25,000 kg - 42 teeth -Remote control - Humidification system - Rear conveyor 5.5m - Overbelt magnet Machine is overhauled and immediately available

The scope of delivery includes: 01x idler, second choice Application: for roller conveyors Material color: sendzimir galvanized Material: Steel Type designation: MRT-50x1,5.20 Total length: 625 mm Web width: 595 mm Roll Ø: 50 mm Thread: smooth with spring pressure Weight / pcs.: approx. 1,370 kg Your contacts in our company: Mr. Andre Evering Mr.: Mario Klöver Lord: Falk German General information about the item: This item is offered for pickup only. A transport that is also desired or a shipment of this article is associated with additional costs, which separately depending on the place of delivery or scope of delivery.

The machine was dismantled at the end of 2021 and has been stored in a hall ever since. The packer is complete with control cabinet and its own compressor. The wiring to the control cabinet was documented during dismantling. Instruction manual on German is also available.

For sale Used cylinder heads. For Jenbacher 6 series F type gas engine. All in good condition and can be refurbished for re use. No cracks and no damage at all. We have 45 pcs at the moment and are available subject to prior sale

Rheon SR-2 bread and roll production line: Weigher capacity: for rolls: up to 3,600 pieces/hour for baguettes: up to 800 kg/hour for loaves: up to 1,500 kg/hour Cuprounder capacity: for rolls: up to 2,400 pieces/hour Consisting of: Rheon V4 Stress Free Divider Type VX 212-800 Year of manufacture 2010 Dough strip width 130-150 mm Product weight range approx. 50 - 2,000 g With round cutting knife With 2-row guillotine With distribution station With 2-row weighing and discharge belts With star cutter oiling With 2 flour dusters With digital control With hopper for approx. 50 kg of dough Includes RHEON CUPROUNDER TYPE SR 002 Year of manufacture 2010 Weight range for rolls approx.: 50–100 g Includes bmTEC processing table Year of manufacture 2022 Dimensions approx. W: 100 x H: 100 x L: 180 cm with wooden panels 40 cm/25 cm wide with conveyor belt ...

Bread slicer, Rösen u. Roberts, Type 28 M / 50

Sheeting machine Fabr Rollfix Type 3W-6300

suitable for nitrogen all stainless steel belt width ± 600 mm nett belt length ± 6.000 mm dimensions (l x w x h) : ± 7.600 x 1.500 x 2.300 mm

150 m pallet rack Jungheinrich type MPB Used goods very good condition, see pictures Height 3.9 m Depth 110 cm, blue Load 8.4 tons Beam length 2.7 m yellow Carrier with ballast /compartment 2400 kg Negotiation price: € 8.990,-- net from stock Offer consists of: + 52 pcs. frame pre-assembled, depth 110 cm, height 3.9 m +204 pcs. beam, length 2.8 m, 2400 kg ballast/compartment +408 pcs. Suspension locks +208 pcs Concrete Anchor Load plates, documents, etc. are a matter of course. Further accessories can be found in the accessories catalogue. Goods are in stock. Transport and assembly possible on request. Viewing possible at any time by appointment. Further information on request. Constantly over 5000 linear meters of pallet racking from numerous manufacturers. (Changes and errors in the technical data, information and prices as well as prior sale ...

plastic belt for blocks of max. 600 x 600 mm belt width 600 mm adjustable outfeed height ± 1.900 mm + 500 mm infeed height : ± 800 mm total dimensions : ± 3.900 x 1.000 x 1.900 mm + (500mm adjustable) adjustable speed mobile

Offer 20142 Specifications: - Tapping capacity up to approx. M 16 - Tapping depth approx. 75 mm - Drill feed Ab + Auf infinitely variable - Projection 90 mm - Spindle speeds up to 290 rpm - Pneumatic connection with pressure reducer 6 bar - Pneumatic foot switch - Drive 400 V / 0.75 kW - Space requirement approx. W 700 x H 2250 x D 800 mm - Weight approx. 150 kg

ELEKTRISCHER KASTENOFEN Verwendungszweck : Pulverhärtung Maximale Temperatur : 220ºC Das Heizsystem des Ofens ist als Zwangskonvektionssystem ausgelegt. Es basiert auf dem Prinzip, dass die Luft des Ofenvolumens mit Hilfe eines Umwälzgebläses in den Ofen gepumpt wird und die Ofentemperatur durch die Wärmeübertragung der Luft, die durch die Heizeinheit strömt, erhöht wird. Die Wände des Ofens und der Heizeinheit bestehen aus modularen Blechen und hochdichten Isolierplatten. Luftverteilungskanäle mit regulierbaren Klappen im Inneren des Ofens sorgen dafür, dass die Ofentemperatur an jedem Punkt gleichmäßig ist. Die Temperaturregelung ist digital und ermöglicht eine präzise Einstellung der Ofentemperatur. Die Heizeinheit wird seitlich, hinten oder oben am Ofen angebracht und besteht aus einer isolierten Heizkammer, einer Heizzelle mit Widerstand im Inneren, eine ...

12 galvanized conveyor belts, belt width 650 mm, capacity 150 to 200 t/h Lengths from 8 meters to 60 meters Left - clockwise rotation, with traction drive 037 KW Tel. 01715213204

1. LIQUID SPRAY BOOTH The spray booth is designed for ventilation and filtering of paint overspray during manual painting application. VENTILATION SYSTEM Side draft ventilation provides high efficiency during paint application. The filter wall is manufactured modularly from galvanized sheet metal panels and the extraction fan is placed on the upper part of the filter wall and choiceed with plastic propeller to prevent the risk of spark formation. The electric motor is placed outside the extraction duct and there is no direct contact of the motor with the polluted air. FILTRATION SYSTEM The extraction filter is on the back surface of the spray booth filter wall and is used in 2 stages with 99.9% efficiency. In order to increase filtration efficiency, cardboard filter and paint stopper fibreglass filter are used as 2 separate layers. The warning lamp on the control panel indicates th ...

Automatic Groove and Grip Hole Eyelet Machine Hang Type 115-20 incl. Conveyor Belt and Ceiling Magazine Built in 1988 OKU-Automatic eyelet sorter, Conveyor belt Length 2,500, width 500 mm, Folding unit HANG, Benefit Investors Machine is in good condition

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

PULVERBESCHICHTUNGSANLAGE, TRANSFER-TYP Aushärteofen - Gas, Diesel oder elektrische Quelle Pulverbeschichtungskabine - Zyklontyp oder mit Patronenfilter Pulverbeschichtungsanlage - manuelles oder automatisches System Hängefördersystem - Raupenfahrwerke und Rumpfform Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachiger Ansprechpartner in Deutschland Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. abcs://vogamachine.com info@vogamakina

TRANSFER TYPE POWDER COATING LINE Curing oven - gas, diesel or electrical source Powder coating booth - cyclone type or cartridge filtered Powder coating equipment - manual or automatic system Overhead conveyor system - tracks trolleys and frull structure Contact us for quotation We provide the best technical solutions and competitive prices German speaking contact in Germany VOGAMAKINA Ltd.

800 x 600 470 mm 137 Piece(s)

800 x 600 445 mm 159 Piece(s)

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

Sliding head lathe Star SR 38 Type A :::SPECIFICATIONS::: CNC Model: Fanuc CNC version: 31i model B Main spindle power: 11Kw Main spindle bar clearance: 38mm Headstock stroke (Z1): 320mm Main spindle speed: 7000 Number of linear axes: 7 Number of fixed tool holder plate positions: 14 Number of driven tool holder plate tool slots: 7 Rapid feeds for linear axes X Y Z: 36m/min High refrigerant pressure: yes External tank system with filter: yes Sub-spindle: yes Sub-spindle speed: 7000 Power against spindle: 5.5Kw Bar clearance: 38mm Number of motorized rear tools: 8 Coolant Used: Neat Oil Model and brand of bar loader: Iemca Boss 552-HD for 4 meter bars Chip conveyor: belt conveyor :::D DIMENSIONS AND WEIGHT::: Length: 2740mm Width: 1315mm Height: 2120mm Weight: 4300Kg

General - Bertolaso Filling and Sealing Combine, YOC 2006 - Running direction left/right - Capacity range up to 8,000 bph 63-digit clamp overhead rinser - Ozone sterilization medium - Fully automatic sterilization before the start of filling - Centrally adjustable inlet stars, easy inlet screw replacement 40-Digit Vacuum Filler - with new gearbox - Centrally adjustable inlet screws - Easy inlet screw replacement - Fully automatic damping - Central height adjustment 6-digit natural cork seamer - with separate cork supply 6-head screw capper for BVS 30/60 and MCA 28 - Central cap supply - with central control station - Automatic faulty bottle ejection and collection station - With fully automatic star adjustment and easy screw change The filling and capping combine is immediately available and can be visited at any time after consultation. Used machines ...

Stainless steel grating mill

Prisma 09C3 inline checkweigher for shipping/display cartons and similar articles, weight range up to 26.88kg.

Grain conveyor belts capacity 150 t/h, belt width 650 mm, MZN 650, galvanized, also for hall filling 2 pieces 60 meters, stationary 1 drum motor each 2 pieces 60 meters revisable LEFT 7 RIGHT, 2 drum motors each, 2 displacement drives, IPE 200 mm rails, trailing cable 1 piece 30 meters, with drum motor 2 pieces 20 meters, with drum motor 1 piece 26.6 meters with regulating gear motor 15 KW, was receiving conveyor with many rollers 2 pcs 5 meter drum motor 2 pieces 7.5 meter drum motor Pictures are welcome to be sent. Dismantled, immediately available. Tel. 01715213204

Lauber Wood dryer longitudinal ventilation, type 4 K-7, Chamber with stacking trolley Contents of the wood dryer: The wood dryer holds 1 parcel with a width of 1.40 m 1 parcel in height of 1.25 m 1 parcel in length of 6.40 m The wood dryer has a total gross volume of 11.2 m³. The wood dryer holds 7.2 m3 of wood net, based on a wood thickness of 50 mm, a stacking strip thickness of 20 mm and 90% width utilization with edged wood. External dimensions of the wood dryer excl. control cabinet: Width: approx. 1.60 m Height: approx. 1.90 m Length: approx. 7.50 m Heating capacity 24.0 kW More info on request

Key data: 1600 KG, 3600 mm, 9000 mm

We offer: Pallet racking, new 600 pitches Manufacturer: Maxrac Specifications: 32 stand frames, approx. 1,700 x 1,050 mm 240 supports, approx. 3,600 mm 480 locking pins Shelf load is 1,600 kg (with evenly distributed load). 19.992,00 € net plus 19 % VAT from stock 21698 Harsefeld. Subject to changes and errors. We are a professional provider – invoice with VAT indicated.

We are selling here a cooking system from the manufacturer Schröter, type HR1 Wg in a very good used and functional condition. Runs on 400 volts, 45 kW, built in 1999, completely stainless steel, Reich digital control, incl. 2 cars, workshop checked, immediately ready for use, dimensions W/D/H 140/130/265 cm, others on request.

Content: 1.000 Ltr. Working pressure: Max. steam pressure 1.1 bar at 50°C, 1.3 bar at 55°C Material: Stainless steel, 1.4404 inner tank, 1.4301 frame and outer jacket Design: cubic, upright, on 4 feet, with welded construction for access by forklift or pallet truck, Insulating jacket with perlite insulation, electrically heated up to 120 °C, 2,000 W, 230 V, Inner tank lined with ETFE coating Spout with disc valve DN 80 reduced to DN 50, cover DN 400, 1 x Safety Valve, 1 x Camlock Coupling 1", Total weight 381 kg Last Purpose: Food Height: approx. 1,670 mm Width/Length: approx. 1,200 mm/1,100 mm

completely stainless steel Track width 800 mm 2 engines "JVM GmbH & Co.KG", type JV 156-250 Opening grille: dia. 14-22 mm Power: 2 x 0.95 kW Dimensions : ± 2,700 x 1,600 x 1,000 mm