We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,851 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
clamping force: 450 kN injection volume: 99 cm³ screw diameter: 30 mm platen size: 860 x 320 mm closing stroke: 406 mm Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive ...
used
clamping force: 1.750 kN injection volume: 318 cm³ screw diameter: 45 mm platen size: 700 x 700 mm daylight between platens - max.: 460 mm Condition: used, Specification: Horizontal injection moulding machine, Injection unit: - Screw diameter: 45 mm - Screw length L/D: 20 - Spray volume: 318 cm³ - Shot weight max.: 287 g - Special spraying pressure: 2,100 bar Clamping unit: - Max. clamping force: 1,750 kN - clamping plates: 700 x 700 mm - Opening path max.: 460 mm - mould installation height: 150 mm - Operating hours: 89217 h - 1x core puller - Handling / Robots: ENGEL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
clamping force: 450 kN injection volume: 135 cm³ screw diameter: 35 mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPE - used clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
clamping force: 450 kN injection volume: 99 cm³ screw diameter: 30 mm platen size: 860 x 320 mm closing stroke: 406 mm Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive ...
used
spindle diameter: 130 mm x-travel: 3000 mm y-travel: 2000 mm total power requirement: 4,5 kW weight of the machine ca.: 30 t Spindle Ø 130 mm Spindle taper SK 50 Working range: X = column, longitudinal 3,000 mm Y = headstock, vertical 2,000 mm Z = spindle stroke 1,000 mm Lower table 3,300 x 2.400 mm Max. weight on table 10 tons/m² Min./ max position of work spindle above table 770 / 2,770 mm Feeds 0.9 - 2,000 mm/min Quick feed for headstock and column 5,000 mm/min Quill feed 0.5 - 1,200 mm/min Speed range, partially infinitely variable 4.5 - 1,250 rpm Weight, approx. 30,000 kg Accessories / Special Features HEIDENHAIN Digital Display for 3 axes. Hardened guideways. Ball screw spindles. Infinitely variable spindle speeds and feeds. Feeds can be individually driven with motor. Moving operating platform. Hanging control panel. Manual operati ...
used
Description Compression machine with rotating table diam. 1600 n. 3 heating floors, dim. 590 x 650 Opening stroke: 400mm Minimum mold: 100mm
used
Description Compression machine with rotating table diam. 1600 n. 3 heating floors, dim. 590 x 650 Opening stroke: 400mm Minimum mold: 100mm
used
Description Compression machine with rotating table diam. 1600 n. 3 heating floors, dim. 590 x 650 Opening stroke: 400mm Minimum mold: 100mm
used
Connected load: 2.8kW, weight: 1.3t.
used
- ENGEL ER-IS Interface. - Prepared for CC300 Control - Compatible with machine: VC from 28 to 220t EM from 30 to 160t EMC from 50-180t - 1 x vacuum circuit - 1 x compressed air circuit - Compatible machine: VC88-220, EM30-160, EMC50-180 t - Stroke (Z): 1.400 mm - Stroke (Y): 800 mm - Stroke (X): 400 mm - Payload: 5 Kg - Driving method: X, Y, Z: servo, C: pneumatic
used
clamping force: 250 kN injection volume: 49 cm³ screw diameter: 25 mm platen size: 300 x 300 mm Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Pump system 75kW 140_140_71 Spare part number: 0403-620-10-10-160 Manufacturer number: UC 0603/001111003 IMB5 + MNR: R901021899 + valve MNR: R900702586 MNR: R901021899 + valve MNR: R900702586 MNR: R901021900 + valve MNR: R900702586 - Fully functional - Expanded from: Engel_DUO2550H-2550M-900WP combi, 160174, 2006
used
- ENGEL ER-IS Interface. - Prepared for CC300 Control - Compatible with machine: VC from 28 to 220t EM from 30 to 160t EMC from 50-180t - 1 x vacuum circuit - 1 x compressed air circuit - Compatible machine: VC88-220, EM30-160, EMC50-180 t - Stroke (X): 400 mm - Stroke (Y): 800 mm - Stroke (Z): 1.400 mm - Payload: 5 Kg - Driving method: X, Y, Z: servo, C: pneumatic
used
Y-travel: 1000mm, z-travel: 3800mm, connected load: 4kW.
used
Weight: 200kg, an inspection is possible.
used
Radial drilling machine used for drilling and milling Manufacturer: COLLET & ENGELHARD GmbH Type: BUV 1600 Year of construction: 1976 horizontally and vertically swivelling head Drilling capacity: 50 mm Travel arm: approx. 800 mm max column travel: 1000 mm Speed: 14 to 710 rpm Spindle stroke approx. 300 mm 380 V Dimensions: approx. 2600 x 1300 x 3000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
used
Inclined conveyor belt on stainless steel profile - Engel WFB100 Year of construction: The inclined conveyor belt on stainless steel profile, with adjustment of the height and angle of inclination Length of the inclined support belt 120 cm, length of the horizontal support belt 260 cm, width of the support belt 40 cm Carriers from the height 8 cm every 28 cm Height of conveyor belt housings 10 cm Mobile conveyor belt, on wheels Price: On request
used
Manufacturer: Engel/Bosch Operating pressure: 280 bar Capacity: 65 l/min Case size: 1800 x 800 x 700 mm Voltage: 380 V Electrical power: 15 kW
used
Ref. no.: 18092 Producer: ENGEL Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Measurements and weight Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 25250 kg
used
Förderbaänder 16 A 380 V Slow runners Length 90 cm Width 15 cm Height 15 cm
used
Engel granulate chute model Anguss Schneidstation 3496-904-00-00-118, SN: 228921. Good technical condition. Machine warehouse in warehouse in Poland, 55-300 Środa Śląska If necessary, additional photos or videos or if you are planning a visit to check our equipment, we invite you. Possible organization of transport, the cost of transport covered by the buyer. Person: Michal Pienio Production Manager UAP-2 marketing2.legnicafaurecia.com FAURECIA Legnica Decoration Plant, Interior Furnishings 180 Gniewomierz 59-241 Legnickie Pole – Poland M+48660719841 Faurecia Legnica Decorations S.A. . Gniewomierz 180, 59-241 Legnickie Pole, entered into the Register of Entrepreneurs of the Court Register kept by the District Court for Wrocław-Fabryczna in Wrocław, IX Commercial Department of the National Court Register, under KRS number No. 0000874432, NIP 6912552442, shar ...
used
Kuka robot from Engel, model KR C4. SN: 396400. In very good technical condition. Machine warehouse in warehouse in Poland, 55-300 Środa Śląska If necessary, additional photos or videos or if you are planning a visit to check our equipment, we invite you. Possible organization of transport, the cost of transport covered by the buyer. Person: Michal Pienio Production Manager UAP-2 marketing2.legnicafaurecia.com FAURECIA Legnica Decoration Plant, Interior Furnishings 180 Gniewomierz 59-241 Legnickie Pole – Poland M+48660719841 Faurecia Legnica Decorations S.A. . Gniewomierz 180, 59-241 Legnickie Pole, entered into the Register of Entrepreneurs of the Court Register kept by the District Court for Wrocław-Fabryczna in Wrocław, IX Commercial Department of the National Court Register, under KRS number No. 0000874432, NIP 6912552442, share capital: PLN 2,560,000.0 ...
used
clamping force: 800 kN injection volume: 78 cm³ screw diameter: 25 mm platen size: 570 x 552 mm Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN08 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm - Control: CC 90-A0 Injection unit: - Injection volume max.: 78 cm³ - Injection weight max.: 90 g - Screw diameter: 25 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 400 rpm - Injection flow: 87 g/sec - Injection flow (increased): 64 g/sec - Specific injection pressure: 2400 bar - Nozzle stroke: ...
used
clamping force: 800 kN injection volume: 154 cm³ screw diameter: 35 mm platen size: 570 x 552 mm Condition: used, Specification: injection moulding machine for LSR - used Nr. 13EN12 clamping unit: - clamping force: 800 kN - size of heating platen: 570 x 552 mm - Between tie bars horizontally: 405 mm - Between tie bars vertically: 345 mm - Opening stroke: 310 mm - Ejector force: 25.4 kN - Ejector stroke: 100 mm - Mould installation height max.: 530 mm - Mould installation height min.: 250 mm - Bar diameter: 60 mm Injection unit: - Injection volume max.: 154 cm³ - Injection weight max.: 156 g - Screw diameter: 35 mm - Metering stroke: 160 mm - Screw speed max.: 20 - 320 rpm - Delivery flow: 35 g/sec - Injection flow: 148 g/sec - Injection flow (increased): 107 g/sec - Specific injection pressure: 1600 bar ...
used
Ref. no.: 18255 Hersteller: ENGEL Year of construction: 2004 Clamping unit Clamping force: 180 ton Opening stroke: 750 mm Distance between tie bars: 960 x830 mm Mould height min.: 500 mm Opening width: 1250 mm Injection unit Screw diameter: 45 mm Injection volume: 318 cm³ Shot weight: 302 g Injection pressure: 1769/2360 bar Measurements and weight Machine weight: 13500 kg Robot Producer: Wittman Type: W743 Year: 2009
used
Gear motor, electric motor, three-phase motor, electric gear motor -Speed: 28 rpm -Power: 0.05 kW -Construction: B3 -Diameter shaft: Ø 12 mm -Protection class: IP 54 -Dimensions: 210/180/H120 mm -Weight: 4.5 kg
used
Conrad Engelke 3m diam. x 2.2m long Autoclave Steam operation Design pressure 7bar Design temp 169deg C Volume 19m3 Length of rotating steel tube 1320mm With new Control Panel Complete with full documentation
used
Manufacturer: Engel Verstellmotor Geräteträger, Year: 1994, Type: Serie A/GNM 4150-B5.2, Volt/Hz: 42/3,1 mpere, pm: 3000, Year :1994
used
Robot - Angel Viper 20 Year of construction: 2015 5-axis robots: axes X, Y, Z, A, B are driven by servo motors (electrically) Touch control panel The safety package for robots Robot with adapter All offered equipment is started by our service technicians before being sold. It is possible to receive a video of the technical tests of the selected devices or to participate in live technical tests at our company in Łódź. Price: On request
used
Gear motor, electric motor, electric gear motor, permanent magnet motor -Manufacturer: Engel, permanent magnet motor geared motor with brake -Engine:Type:GNM31650-G2.6-B5.2 -Voltage: 24V / 50W / 3000 rpm -Gear: Type G 2.6 i= 30:1 -Shaft: Ø10 x 23 mm -Protection class: IP54 -Brake: 0.5Nm -Dimensions: 250/125/H95 mm -Weight: 2.4 kg.
used
Chassis, electric motor, DC motor, traction motor, drive motor, steering motor -Manufacturer: Engel, steering motor from Jungheinrich electric forklift -Type: GNM5460E-G18 -Motor: 24V/240W -Dimensions: 150/130/H365 mm -Weight: 7 kg
used
Chassis, electric motor, DC motor, traction motor, drive motor, steering motor -Manufacturer: Engel, steering motor from Jungheinrich ESE 320 G 20-240.54 electric stacker -Type: GNM 5460-G18.5-MIR1 Ser. H -Motor: 24V/240W -Dimensions: 135/130/H365 mm -Weight: 8 kg
used
clamping force: 4.000 kN injection volume: 735 cm³ screw diameter: 60 mm platen size: 1.400 x 1.030 mm Condition: used, Specification: horizontal injection moulding machine, factory no: Injection unit 1: - screw diameter: 60 mm - metering stroke: 200 mm - Screw speed: 226 rpm - Injection flow: 351 cm³/sec - Injection volume: 735 cm³ - Spec. injection pressure: 1.489 bar - Spec. injection pressure increased: 2,011 bar Injection unit 2: - Screw diameter: 40 mm - Metering stroke: 140 mm - Screw speed: 400 rpm - Injection flow: 197 cm³/sec - Injection volume: 251 cm³ - Spec. injection pressure: 1.286 bar - Spec. injection pressure increased: 2.029 bar Clamping unit: - Clamping force max.: 4,000 kN - Clamping platens: 1,400 x 1030 mm - Opening stroke: 954 mm - Max. platen distance: 1,520 mm - Ejector stroke: 250 mm - Ejector forc ...
used
Exhaust air purification system Manufacturer: Langbein Engelbracht Type: DV2-92 Plant number: No.20245 Year of construction:2004 Exhaust air volume: min. 1000 - max. 3500 Nm³/h Pressure drop: 60 mbar Burner: Gas Burner Inlet temperature: 20°C Power: Heat exchanger 600 kW Heating capacity: 230 kW Reaction temperature: 820 - 950°C Included: documentation, chimney, PC for control with software, EURO-FID, piping (if desired), control cabinet Location: Neu-Ulm
used
General SKU336T902 LocationBarneveld MakeEngelsmann TypeM3.C.187/3/1.4541 Mach.No.32516 Main Features MaterialStainless steel Motor1.5 KW Length700 mm Specified Features - Sorting sieve Sorting sievecheck Sieve surface1,9 m² Number of sieve decks:2 Number of fractions:3 Sieve sizes700x680 mm Sieve perforation5,5-1,5 mm With covercheck InletDia: 150 mm OutletDia: 140 mm, Dia: 110 mm (2x) Unbalance drivecheck Motor1.5 kW, 220-240/380-420 Volt, 940 rpm Variable speed drivecheck MaterialStainless steel 1.4541 (321) Information Year of construction2007 Mounted on mild steel framecheck Floorspace4,5x1,9 m Total height1,6 m Weight2100 kgSorting sievesEngelsmannSieves > Sorting sievesBrand > Engelsmann What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You ar ...
used
General SKU336T901 LocationBarneveld MakeJ. Engelsmann AG TypeM3.C.187/3-1.4541 Mach.No.30059 Main Features MaterialStainless steel Motor1.5 KW Length700 mm Specified Features - Sorting sieve Sorting sievecheck Sieve surface1.9 m² Number of sieve decks:2 Number of fractions:3 Sieve sizes700x680 mm Sieve perforation5,5-1,5 mm With covercheck InletDia: 150 mm OutletDia: 140 mm, Dia: 110 mm (2x) Unbalance drivecheck Motor1.5kW, 220-240/380-420 Volt, 940 rpm Variable speed drivecheck With extra sieve decks1 MaterialStainless steel 1.4541 (321) Information Year of construction2006 Mounted on mild steel framecheck With switchcheck With switchgearcheck(as is) Floorspace4,5x1,9 m Total height1,6 m Weight2100 kgSorting sievesEngelsmannSieves > Sorting sievesBrand > Engelsmann What you can expect from Foeth: -- Machine is in working condition -- At a reduced price ...
used
General SKU179D660 LocationBarneveld MakeEngelsmann Main Features MaterialStainless steel Motor0.25 KW Length2500 mm Specified Features - Sorting sieve Sorting sieve(1x) Number of sieve decks:2 (2500x220mm) Number of fractions:2x 5 500x220mm) With covercheck InletDia. 100mm Outlet11x Dia. 25mm Motor0,25 KW MaterialStainless steel Information With switchgearcheck Floorspace3,4x0,9 M Total height2,0 MSorting sievesEngelsmannSieves > Sorting sievesBrand > Engelsmann What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
used
General SKU043R200 LocationBarneveld MakeEngelsmann TypeMFL 85N/80-E1 No.30223/88, Material hastelloy Main Features Motor24 KW Inlet diameter300 mm Width150 mm Specified Features - Miscellaneous Mill Hammer mill(1x) Rotor sizeDia. 300x150mm Fixed hammers(6x4) Motor24 KW, 380/660 Volt, Ex Speed2300 Rpm Information Floorspace1,7x0,7 M Total height1,2 M Weight800 KgMiscellaneous MillsEngelsmannMills > Miscellaneous MillsBrand > Engelsmann What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
used
General SKU245P314 LocationBarneveld MakeEngelsmann AG (DE) TypePalafix 20/30 No.48262 Year of construction1993 Main Features MaterialStainless steel Motor0.55 KW Length300 mm Specified Features - Rotating sieve Rotating sievecheck Sieve sizesdia.200mm x L 300mm Inletdia.300 mm Outletdia.240 mm Motor0.55 KW, 220/380 Volt (EEx) Speed680 rpm With sieve cagecheck Sieve perforation2 mm MaterialStainless steel 1.4571 (316Ti) Information Floor space1,7x0,5 M Total height1,0 M Weight200 KGRotating sievesEngelsmannSieves > Rotating sievesBrand > Engelsmann What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
used
General SKU004U062 LocationBarneveld MakeEngelsmann TypeKSM-9 Cbm No.10 562 Year of construction1985 Main Features MaterialStainless steel Volume12000 Ltr. Motor16 KW Specified Features - Pre-mixer MaterialStainless steel 1.4541 (321) Pre-mixerConical screw mixer (1x) Capacity12.000 Ltr, Useful 9.000 Ltr Vessel sizesdia. 2100x5050mm Manholedia. 500mm Inletdia. 150mm Motor11/16 KW, 500 Volt (Ex) Speed mixing shaft3/6 Rpm Information Floorspace2,2x2,2 M Total height6,5 M Weight8500 KG ATEX compatiblecheck Extra Specifications- Jacketed screw (120 Ltr), Working pressure 4 bar (Test pressure 5,2 Bar) Pre-mixersEngelsmannMixers > Pre-mixersBrand > Engelsmann What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, ...
used
90T Engel ES 330/70H. Used but in excellent condition with very low hours (56171). The machine was originally a 70T but it was uprated to 90T by the previous owner. Clamping Force: 90 Up-rated Screw Diameter: 35mm DBTB: 470 X 470mm Core Pull: 2 Air Circuit: 2 Please note - The hopper dryer will be removed and not included in the sale.
used
Closing unit Clamping force [kN] 2600 Injection unit Screw diameter [mm] 60 Injection volume [cm3] 608 Injection weight [g] 669 Injection pressure [bar] 1725 Dimensions and weight Net weight with control cabinet [t] 22.2 Dimensions (length x width x height) [m] 7.5 x 1.95 x 3.1 The diameter of the screw in the unit is W 40mm The injection volume of the W unit is 251 cm3 The injection weight of the W unit is 276.1g The specific injection pressure of the unit is W 1297 bar The screw diameter in the V unit is 22mm
used
Used J. Engelsmann model VIRO 300-800-4571-St/FDA-konform polished stainless steel (AISI 316Ti) cylindrical rotary sifter. Cylindrical screen measures 300 mm diameter x 600 mm lenght. 3-blade rotor is driven through Ex Stöber gearbox by 3.0 kW, 400 V, 1425 rpm, 50 Hz Ex electric motor, the final rpms are 602 rpm. There is also ATEX vibro motor 0.26 kW, 400 V, 3000 rpm, 50 Hz installed above the screen to increase screening efficiency. Feeding inlet has diameter 120 mm. Discharge hopper for particals smaller than holes of the screen has pneumatical valve and diameter 300 mm. Discharge hopper for particals bigger than holes of the screen has diameter 250 mm. Mounted on stainless steel frame. Overall dimensions are approx: 2600 mm x 800 mm x 2280 mm (height), weight approx 500 kg.
used
Control CC 100 for ENGEL injection moulding machines
used
MOOG valve for injection moulding machines ENGEL
used
Inverter for ENGEL robots Acopos Multi PO 220 Acopos Multi CO160
used
The KEBA keypad HT511-221/ENGEL/50200/19 - 2-stage enabling button - comes from an ENGEL ERC 34-1-E Handling from 2007. The serial number is 50200-01062. The device is ready for connection with a coupling plug.
used
The KEBA keypad HT501-221/ENGEL/24244/18 - 2-stage enabling button - comes from an ENGEL ERC 24 Handling. The serial number is P21305-02216. The device is ready for connection with coupling plug incl. soft case.
used
The KEBA keypad HT501-221/ENGEL/24244/18 - 2-stage approval button - comes from an ENGEL ERC 24 Handling. The serial number is P21305-02213. The device is ready for connection with coupling plug incl. soft case.
used
Injection pump in Exchange