elo motor used for sale

Gear motor, electric motor, electric gear motor -Speed: 152 rpm -Power: 2.9 kW -Diameter shaft: Ø 40 mm -Construction: B5 -Protection class: IP 44 -Brake -Dimensions: 740/300/H280 mm -Weight: 65 kg

Gear motor, electric motor -Speed: 56 rpm -Power: 1.5 kW -Construction: B5 -Diameter shaft: Ø 45 mm -Protection class: IP 54 -without breaks -Dimensions: 650/280/H300 mm -Weight: 50 kg

Gear motor, electric motor -Speed: 110 rpm -Power: 0.18 kW -Construction: B5 -Diameter shaft: Ø 17 mm -Protection class: IP 54 -Number: 1x gear motor available -Price: per piece -Dimensions: 315/140/H195 mm -Weight: 6.8 kg

Gear motor variable / adjustable BRUMO GRG1U100B 0.37 kW 29 - 159 rpm 220 / 380 V shaft diameter: Ø 20 mm used, tested ! Dimensions: 500 x 370 x 210 mm

sheet width: 2540 mm plate thickness: 2.00 mm thickness at Niro-steel: 1.25 mm no. of strokes: max. 63 Hub/min cutting angle: 1.13 Grad table height: 750 mm table width: 320 mm distance between columns: 2620 mm back stop - adjustable: 5.0 - 550 mm Control: konv. engine output: 3.0 kW weight of the machine ca.: 1600 kg range L-W-H: 3100 x 1980 x 1400 mm Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analogue display adjustable from the front stepless adjustment over the entire travel range - recessed grips in the support table - 1x hold-down bar - 1x side stop - 3x support arms - 1x freely movable foot switch - operating instructions (PDF) Special accessories included: - sheet metal holding device for thin sheet metal cuts The data for this ad was created wit ...

Gear motor, electric motor, three-phase motor -Speed: 65/78 rpm -Power: 0.25 kW -Construction: B3/5 angle -Diameter shaft: Ø 20 mm -Protection class: IP 65 -Dimensions: 305/170/H195 mm -Weight: 7.6 kg

Permanent magnet motor, permanent magnet motor, gear motor, electric motor, servo motor -Power: 22 Nm -Speeds: 300 rpm -Protection class: IP 54 -Voltage: 24 V -Diameter: Ø 15 mm -Price: per piece -Number: 7x available -defective foot: 1 -Dimensions: 380/110/H160 mm -Weight: 9.1 kg

Gear motor, electric motor, three-phase motor -Speed: 4 rpm -Power: 0.09kw -Construction: B3 angle -Diameter shaft: Ø 18 mm -Protection class: IP 54 -Number: 1x motor available -Dimensions: 290/230/H205 mm -Weight: 10kg

Gear Motor SEW SA42LP71 D63L4B03/HR/TF ( SA42LP71D63L4B03/HR/TF ) 0,0,0 25 kW 34 rpm i=37,94 220/ 380 V IP54 B35, with foot and flange shaft diameter: Ø 30 mm New !' Dimensions: 510 x 180 x 180 mm

sheet width: 1040 mm plate thickness: 2.50 mm thickness at Niro-steel: 1.25 mm no. of strokes: max. 90 Hub/min cutting angle: 2.70 Grad distance between columns: 1060 mm work height max.: 940 mm back stop - adjustable: max. 550 mm column arm: 120 mm voltage: 400 V engine output: 4.0 kW weight of the machine ca.: 820 kg. range L-W-H: 1650 x 1200 x 1250 mm Equipment: - robust / motorized crank guillotine shears with motor drive - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analog position display adjustable from behind continuous adjustment over the entire travel range travel range max. 550 mm - 1x hold-down bar - 1x side stop - 1x front support arm - original operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, electric motor -Speed: 80 rpm -Power: 0.55 kW -Construction: B5 angle -Diameter shaft: Ø 20 mm -Protection class: IP 54 -Dimensions: 450/270/H175 mm -Weight: 20 kg

Gear motor, electric motor, three-phase motor -Power: 0.55 kW -Speed: 110 rpm -Shaft: Ø 20 mm -Construction: B5 angle -Protection class: IP 54 -Number: 1x motors available -Price: per piece -Dimensions: 450/270/H175 mm -Weight: 20 kg

Gear motor, electric motor -Speed: 100 rpm -Power: 0.11 kW -Construction: B5 -Diameter shaft: Ø 20 mm -Protection class: IP 33 -Number: 2x gear motors available -Price: per piece -Dimensions: 335/170/H160 mm -Weight: 9.2 kg

Gear Motor with Brake ABM Type: ZFB 12SO / G80 F4D 808-4 ( ZFB12SO / G80F4D808-4 ) 0,0,0,0 75 kW 430 rpm 230 / 400 volts 5 -100 Hz IP 54 / 55 flange Ø 140 mm used, tested ! Dimensions: 470 x 150 x 200 mm

sheet width: 1050 mm plate thickness: 2.0 mm roll length: 1070 mm roll diam. toproll: 75.0 mm engine output: 1.5 kW weight: 325 kg range L-W-H: 1530 x 700 x 1160 mm Exhibition machine - like NEW not yet in use () Special price on request Equipment: - electro-motor-driven 3-roller round bending machine - asymmetrical roller arrangement - 2x driven rollers using a brake motor - manual folding bearing for quick removal of the workpiece - wire insertion grooves on the bottom and rear rollers - double foot switch for R/L running including emergency stop button - rear roller feed with ratchet lever - electrical safety device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, electric motor -Speed: 15.5 rpm -Power: 0.11 kW -Construction: B5 angle -Diameter shaft: Ø 18 mm -Protection class: IP 54/65 -Number: 1x geared motors available -Price: per piece -Dimensions: 325/150/H145 mm -Weight: 9.2 kg

Gear motor, electric motor, electric gear motor -Speed: 18 rpm -Power: 0.075 kW -Construction: B3 -Diameter shaft: 17 mm -Protection class: IP 54/65 -Price: per piece -Number: 2x available -Dimensions: 280/145/H140 mm -Weight: 6.7 kg

Geared Motor GETRIEBEBAU NORD Type: SK 01F-71 L/4 ( SK01F-71L/4 ) 0.37 kW 70 rpm 230 / 400 Volt IP 55 Flange Ø 210 mm used, tested ! Dimensions: 400 x 170 x 210 mm

sheet width: 4080 mm plate thickness: 2.0 mm ST thickness at Niro-steel: 0.8 mm Sheet thickness for ALU: 2.5 mm no. of strokes: 34 Hub/min cutting angle: 1.3 Grad distance between columns: 4310 mm back stop - adjustable: 15.0 - 750 mm table height: 820 mm Control: ELGO engine output: 9.0 kW weight of the machine ca.: 3600 kg. range L-W-H: 5250 x 2200 x 1400 mm Good condition () Current new price approx. €70,000 Special price upon request The MHSU motor-driven guillotine shear is based on a torsion-free, rigid welded construction and a dynamic, quiet, and powerful gear motor. High static and dynamic rigidity is ensured by robustly dimensioned main components such as the cutter bar, support table, side supports,and the main drive unit. The motor- driven guillotine shear was developed forsheet metal and plastics processing. With these shears, you can effortlessly produce clean cuts in  ...

Gear motor, electric motor, three-phase motor -Speeds: 80 rpm -Power: 0.12 kW -Construction: B3 -Diameter shaft: Ø 22 mm -Protection class: IP 54 -Price: per piece -Number: 12x available -Dimensions: 350/160/ H200 mm -Weight: 10.1 kg

Gear motor, electric motor, electric gear motor -Speed: 23/100 rpm -Power: 0.15/0.6 kW -Construction: B3 -Diameter shaft: 30 mm -Protection class: IP 54 -Dimensions: 560/230/H200 mm -Weight: 30 kg

Geared motor GROSCHOPP Type: WK 1441 - 1 ( WK1441-1 ) DM 80-40 0,0,0,0 022 kW 24 rpm 230 / 400 V shaft diameter: Ø 12 mm flange diameter: Ø 110 mm aluminium housing used, tested ! Dimensions: 230 x 170 x 130 mm

plate thickness: 1.20 mm ST Shaft length: 140 mm roll diameter: 62.0 mm throat: 100 mm roll speed: 16.0 + 32.0 U/min engine output: 0.75 kW weight: 135 kg range L-W-H: 900 x 450 x 1350 mm Display machine - like new Never been used () Special price upon request Features: - 8 pairs of beading and flanging rollers included - Robust beading machine with motor-driven rollers - Lower shaft with adjustable stop - For economical production of a wide variety of bead types - High accuracy thanks to precision-mounted shafts - Clearly arranged control elements - Manual adjustment of the upper roller - 2 bending speeds - Powerful drive motor, even under continuous load - 1 mobile foot switch for forward and reverse rotation - Machine base frame The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Winding motor, drum winder for crane, trailing cable motor, gear motor, electric motor -Speed: 25 rpm -Power: TA = 8 Nm -Construction: B5 -Diameter shaft: Ø 20 mm -Protection class: IP 54 -Number: 1x motors available -Price: per piece -Dimensions: 360/140/H185 mm -Weight: 14.4 kg

Gear motor, electric motor -Speed: 18 rpm -Power: 0.135 kW -Construction: B3 -Diameter shaft: Ø 20 mm -Protection class: IP 54 -Dimensions: 350/190/H175 mm -Weight: 12 kg

Gear motor variable SEW transmission: S42-VUO 17-81 rpm manually adjustable via V-belt motor: eDFT71D-4 0,0,0,0 37 KW 1370 rpm 220/ 380 V 3AC IP54 Shaft diameter: Ø 25 mm Motor base: 130 / 135 x 124 mm Hole spacing ( parallel to shaft ): 100 mm hole spacing ( transverse to shaft ): 80 mm hole diameter: Ø 10.5 mm New ! Dimensions: 430 x 220 x 360 mm

Gear motor, electric motor, electric gear motor -Speed: 27 rpm -Power: 0.18 kW -Construction: B3 -Diameter shaft: 20 mm -Protection class: IP 65 -Price: per piece -Number: 3x available -Dimensions: 370/180/H200 mm -Weight: 14.2 kg

Gear motor, electric motor, three-phase motor -Speeds: 200 rpm -Power: 0.37 kW -Construction: B5 -Diameter shaft: Ø 20 mm -Protection class: IP 55 -Number: 1x motors available -Price: per piece -Dimensions: 420/180/H160 mm -Weight: 16 kg

Geared motor with brake VEM ZG5 BMRZA 100 L 4 ( ZG5BMRZA100L4 ) 4,4,000 0 kW 50 rpm 220 / 380 V IP44 shaft diameter: Ø 75 mm Flange diameter: Ø 400 mm New ! Dimensions: 920 x 400 x 440 mm

plate thickness: 2.5 mm ST shaft length: 250 mm roll diameter: 96.0 mm throat: 160 mm roll speed: 6.0 + 13.0 U/min. total power requirement: 1.5 kW weight: 350 kg range L-W-H: 1400 x 550 x 1120 mm Display machine - like new Never been used () Special price upon request Features: - 4x pairs of beading and flanging rollers included - Robust beading machine with motor-driven rollers - Lower shaft with adjustable stop - For economical production of a wide variety of bead types - High accuracy thanks to precision-mounted shafts - Clearly arranged control elements - Manual adjustment of the upper roller - 2x bending speeds - Powerful drive motor, even under continuous load - 1x mobile foot switch for forward and reverse rotation - Machine base frame The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, electric motor, three-phase motor -Speed: 15/60 rpm -Power: 0.1/0.45 kW -Construction: B3 -Diameter shaft: 25 mm -Protection class: IP 54 -Dimensions: 410/210/H190 mm -Weight: 24 kg

Gear motor, electric motor, three-phase motor, angular gear motor -Speed: 8.8 rpm -Power: 0.12 kW -Construction: B5 angle -Diameter shaft: Ø 20 mm -Protection class: IP 54 -Price: per piece -Number: 2x available -Dimensions: 330/170/H140 mm -Weight per piece: 13 kg

Geared motor with brake VEM ZG4 BMRE 100 L 6 ( ZG4BMRE100L6 ) 2,2,2 2 kW 25 rpm 220 / 380 V IP44 shaft diameter: Ø 60 mm Flange diameter: Ø 300 mm New !' Dimensions: 780 x 300 x 360 mm

sheet width: 1050 mm plate thickness: 3.0 mm thickness at Niro-steel: 1.5 mm no. of strokes: 35 Hub/min cutting angle: 2°30 ° engine output: 3.0 kW table height: 810 mm weight of the machine ca.: 1150 kg. range L-W-H: 1300 x 1520 x 1170 mm from a maintenance workshop () Furnishing: - robust electro-motorized metal sheet shears - manual backgauge - adjustable up to 610 mm, using the handwheel from the back - 1x side stop including mm scale - 2x table sheet metal support arms - Piece counter - freely movable foot switch - rear sheet metal slide - EMERGENCY stop button at the front Machine link: https://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=100 8-9325126 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, electric motor, electric gear motor -Speed: 120 rpm -Power: 0.25 kW -Diameter: Ø 20 mm -Construction: B3 -Protection class: IP 54 -Number: 1x motors available -Price: per piece -Dimensions: 340/190/H175 mm -Weight: 12.5 kg

Gear motor, electric motor -Speed: 8 rpm -Power: 0.15 kW -Construction: B3 -Diameter shaft: Ø 25 mm -Protection class: IP 54 -Dimensions: 470/200/H160 mm -Weight: 21 kg

Gear motor, electric motor -Speed: 65 rpm -Power: 0.55 kW -Construction: B5 -Diameter shaft: Ø 25 mm -Brake: 24 V -Protection class: IP 65 -Number: 1x geared motors available -Price: per piece -Weight: 31 kg

Servo Motor with Gearbox and Brake, Permanent Magnet Motor ELAU SB105-30-08-05-19-S-01-64-BOKN 19192308-012 3000rpm IP64 Gearbox: PFEFFER & PARTNER RPLN 15-2 BK i 45:1 shaft: Ø 32 mm flange: 105 x 105 mm used, tested ! Dimensions: 660 x 140 x 110 mm -

sheet width: 1320 mm plate thickness: 2.5 mm ST thickness at Niro-steel: 1.2 mm blade length: 1350 mm no. of strokes: 34 Hub/min back stop - adjustable: max. 825 mm cutting angle: 1.5 ° work height max.: 810 mm Control: konv. engine output: 3.0 kW weight: 1100 kg range L-W-H: 1950 x 1450 (2000) x 1200 mm Exhibition machine - like new Never been used () Special price upon request Features: - Robust electro-mechanical sheet metal shear - Heavy-duty / robust drive motor - Manual backgauge, including analog position indicator Adjustment range max. 825 mm - Manual cutting gap adjustment - 2x table side stops including mm scale - 1x front stop bar - manually adjustable - 2x front support arms - Grip recess in the front work table - 1x freely movable foot switch, including emergency stop button - Control cabinet/operating panel - front right - Rear safety device - Rear sheet chute - Connec ...

Geared motor, electric motor, electric geared motor -Condition: unused -Speed: 28 rpm -Power: 0.37 kW -Design: B3 angle -Shaft diameter: 30 mm -Protection class: IP 54 -Number: 1x motor available -Dimensions: 695/270/H185 mm -Weight: 32 kg

Gear Motor LEROY SOMER CBA3 BS ( CBA3BS ) 0,0,0 16 kW 50 rpm i=29,30 ATAV F71 BSTA4, explosion-proof 220/ 380 V IP54 design: flange shaft diameter: Ø 20 mm Dimensions: 500 x 160 x 160 mm

sheet width: 2050 mm plate thickness: 10.0 mm ST pre-bending: 8.0 mm ST diameter of upper rolls: ~ 205 mm side roll diameter: ~ 195 mm Control: konv. oil volume: 80.0 Liter voltage: 380 V total power requirement: 5.5 kW weight: 3200 kg range L-W-H: 4500 x 1500 x 1300 mm Features: - Robust electro-hydraulic 3-roll bending machine - 3-roll concept offers a wide range of bending and rounding options - Pivoting control unit at the front Operation - Control of all rolls and machine axes Digital position display Manual operation via joysticks - Diameters of up to 1.1 times the top roll diameter are possible - Forged and hardened rolls with a hardness of 53-55 HRC - Low-maintenance, stable machine design - Sturdy welded steel construction - Electro-hydraulic folding bearing for easy pipe removal - Pressure gauge / pressure indicator for the rolls - Safety device (safety lanyard with switch u ...

Gear motor, electric motor, three-phase motor -Speed: 31.5/63 rpm -Power: 0.25/0.37 kW -Construction: B3 -Diameter shaft: Ø 25 mm -Protection class: IP 44/55 -Price: per piece -Number: 2x available -Dimensions: 405/190/H160 mm -Weight: 17 kg

Geared motor, electric motor, electric geared motor -Speed: 177 rpm -Power: 0.55 kW -Design: B3 -Shaft diameter: 20 mm -Protection class: IP 54 -Dimensions: 315/145/H190 mm -Weight: 11.7 kg

Gear motor variable / adjustable SEW S60- D22 B ( S60-D22B ) 0,0,0,0 75 kW / 0.48 kW (1440 / 940 rpm) 15 - 115 rpm manually adjustable 380 V IP55 shaft diameter: Ø 35 mm New ! Dimensions: 710 x 350 x 280 mm

sheet width: 3050 mm plate thickness: 3.0 mm ST pre-bending capacity: 3.0 mm ST upper roll diameter: 170 mm lower roll diameter: 170 mm side roll diameter: 180 mm Control: konv. 0: 380 V total power requirement: 3.0 KW weight: 4250 kg In good condition With new rubber-coated top roll () Also suitable for bending non-ferrous metals Equipment: - Electro-hydraulic 3-roll bending machine - Asymmetrical roll arrangement - Electro-motor-driven side roll adjustment Including digital position display - Manual bottom roll adjustment Via hand crank - Including conical bending device Inclined bottom roll and side rolls Parallel alignment in any side roll position - Hardened rolls SAE 1050 CK 45 - Manual folding storage for removing closed pipes Top roll must be raised before opening the storage (e.g., forklift/crane) - Safety device - Connection cable + connector - 4-way foot switch 2 butt ...

geared motor, electric motor -Speed: 85 rpm -Power: 0.37 kW -Design: B5 -Shaft diameter: Ø 25 mm -Protection class: IP 65 -Price: per piece -Quantity: 1 available -Dimensions: 450/205/H200 mm -Weight: 20 kg

Stepper gear motor with brake, universal rotary tables with cam drive SOPAP TSa 11000-8-360-200-D ( TSa11000-8-360-200-D ) 103.3 HZ 310 V IP54 used, tested ! Dimensions: 1500 x 1000 x 530 mm

sheet width: 1070 mm plate thickness: 4.0 mm pre-bending: 3.0 mm roll length: 1070 mm roll diam. toproll: 110 mm bending speed: 3.0 m/min engine output: 2.2 kW weight: 848 kg range L-W-H: 2250 x 1000 x 1800 mm New price ~ 10.000 euros Exhibition machine - like NEW () Equipment: - robust electro-mechanical round bending machine - 2x central rollers driven by electric motor (top & bottom roller) - right/left running of the rollers - top roller can be manually swiveled out, with folding bearing - manual delivery of the side roller - including conical bending device - asymmetrical roller arrangement - rollers with profile inlets - safety device (safety line with switch unit) - 1x freely movable control panel - operating instructions (ENG) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, electric motor, three-phase motor -Speed: 69 rpm -Power: 0.55 kW -Construction: B3 -Diameter shaft: 25 mm -Protection class: IP 55 -Dimensions: 455/200/H160 mm -Weight: 20 kg