electro hydraulic used for sale

pressure: 1000 t stroke: 600 mm weight of the machine ca.: 4 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: . t throat: . mm stroke: . mm total power requirement: . kW weight of the machine ca.: 4 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 3100 mm, 6 mm

Max. cutting length ... 3100mm Max. sheet thickness ... 6mm Drive... Hydraulic Main engine power ... 11kW Number of strokes ... 20/min Machine weight... 5500kg L x W x H ... 3900x2560x1560mm The machine is in good condition, possible to test under power,

Hydraulic copying device SAUTER type KMC 8001Copier turning device, copying turning device for lathesThe copying device comes from a lathe.Connections for oil supply and oil returnCopying stroke: approx. 140 mmRadial travel at 60 Construction: 120 mmRequired operating pressure: approx. 25 barOil volume flow: max. 7 litres/min. Drive power of the lathe: max. approx. 15 kWSpan cross-section: max. 3.5 mm²Copy carriage stroke: approx. 125 mmDistance of lathe chisel to the stylus: 800 mmDead weight Copier: approx. 100 kggoods

Single column hydraulic press MAE type S63SZ SOMasch.Nr. 551277 year of construction approx. 1977Nominal compressive force 63 ton. Pressing force: 50 tons (Practically tested)Projection 320 mmTable surface 850 x 630 mmRam area 1050 x 500 mmRam stroke 500 mmInstallation height max. approx. 730 mmTable height above floor 970 mmTank capacity hydraulics 600 litersDrive power 15 kWNerg connection 380 volts, 50 Hz- Hydraulic drawing cushion under the table with holes through the table top- 2-hand control- Electrical control cabinet damagedSpace requirement L x

Hydraulic Machine Vise ARNOBock width: 200 mmJaw height: 60 mmClamping force: 8 ton. Clamping range: 0 to 370 mmOpening width: max 373 mmGuideway height: 140 mm- 2 clamping ranges adjustable via plug-in pins- TurntableDimensions L x W x H: 900 x 400 x 210 mmWeight: 125 kgGood condition; used

Hydraulically switchable gearbox for change of direction of rotationHydraulic reverse gear of latheYear of construction approx. 1985Alternating gearbox for fast change of direction of rotationClockwise or counterclockwise rotation- electric hydraulic pump for hydraulic pressure generation (380 volts, 0.25kW)- 2 pieces of solenoid valves for switching from left to clockwise rotation- equipped with pulleys 230 and 200 mm- was driven by a 15 KW drive motor, fast change of direction of rotation with high torque transmission- Drive motor always runs on the right, gearbox is hydraulically activated

Hydraulic self-centering steady rest, luenette, Lynette SMW AUTOBLOKHydraulic steady rest with hydrostatic bearingSuitable for GILDEMEISTER / MAX MÜLLER lathe MD 5 Type: SLK 8-70 NSpanning range: 8 to 70 mmOperating pressure: approx. 60 barBezel foot: 245 x 240 mmDesign: fixed- 3 pieces roller bearing 35 mm- Roller width 18 mm- hydraulically self-centeringDimensions L x W x H: 350 x 250 x 550 mmWeight: 65 kgGood condition; used

Hydraulic guillotine shears STEINER type HTS 30/20 RMasch. No. 315 Year of construction 1982Cutting length 3050 mmCutting thickness 20 mmBack gauge 800 mm controlledMotor power approx. 30 kWNet connection 400 volts, 50 Hz- Back gauge with positioning control ELGO- Back gauge adjustment via ball screws- Safety light barrier SICK front as protection against interference- 3 pieces Material Support arms with ball rollers- Electric foot switch- Replacement knifeSpace requirement of the basic machine L x W x H 4650 x 2610 x 3200

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Rotary indexing table, rotary indexing table with 16 stationsRotary transfer machine + hydraulic press TOXRundtaktautomat Special machine with several assembly stationsProduction and assembly system in rotary transfer processFrom special machine manufacturer AKE-technologies GmbHSerien number: 01-45-064Order number: 11111Year of construction: 2012- large rotary indexing table WHITE type TC500, with 16 stations- pressing station with TOX powerhouse- vibation conveyor- conveyor belts- test stations - some stations still open

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Hydr. Hacksaw, hacksaw, lifting saw KASTO type PSB WBS 210 / 230Masch. No. 115 106 1212 / 72783 Year of construction 1986Sawing area - Round 250 mmSawing area - Square 225 x 225 mmSawing area - Rectangle 260 x 100 mmCutting speed 11 -13 - 17 - 22 - 26 - 34 m/min. Saw blade length 400 mmMotor power 1.4 and 1.8 kW pole-switchableMains connection 380 volts, 50 Hz- only for 90 cuts, no mitre adjustment- Saw motor with 2 speeds and 3 V-belt steps- Hydraulic saw bar feed- hydraulic

Hydraulic Cylinder Double-acting HÄNCHEN Type ServoslideFlange Cylinder, Ideal for Workshop PressSeries No.: S004420 Year of Manufacture 2010Cylinder Stroke: 400 mmOperating Pressure: 300 barPiston Rod: 160 mmPiston Diameter: 220 mmCylinder Press Force at 300 bar: 114 Tonflange Outer Diameter: approx. 400 mm with 16 Bores 24.5 mmTotal Length Piston Rod Retracted: approx. 1230 mm (with the Wheel Measuring Cell)Total Length from Flange to Cylinder Upper Edge: approx. 750 mm- Hydraulic Connection Thread G 1 1/4 - Thread on the piston rod M150 x 3 mm

Hydr. Hacksaw (Made in Croatia) Type BS 320Year of construction approx. 1980Saw range Round 320 mmSaw area Square 280 x 280 mmSaw blade 550 x 45 x 2.25 mmMaterial Inlet height 680 mmSaw speed 42 - 55 - 85 - 110 strokes/min. Motor power 1.8 and 2.4 kW Pole switchableMains connection 400 volts, Hz- Mitre adjustment up to 45- Saw motor with 2 speeds and 2 V-belt steps- Hydraulic saw bracket lowering- Hydraulic cutting pressure adjustment via throttle valve- Coolant device in the

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

Hydraulic power unit for mobile clinching pliers or mobile former ECKOLD type HA 500 / 2Fabr. No. 737 / 783 Year of construction 1991Hydraulic power unit type HA 500 / 2Operating pressure 50 - 500 bar adjustableFlow rate 2.6 l/minTank capacity 16 litresEngine power (hydraulic) 3 kWNead power 380 Volts, 50 Hz.Control voltage 24 Volts, DC pressure line with screw coupling- With solenoid valve HAWE GS 2-2- mobile on 4 swivel castorsWeight without hydraulic oil 125 kggood condition; used

Hydraulic guillotine shears FASTI type 509 - 25/4Masch. No. 5418 Year of construction 1991Cutting length 2535 mmCutting thickness 4 mmBack gauge 5-1000 mm (controlled)Cutting angle adjustableHydraulic pressure max. 290 barMotor power 7.5 kWNeching connection 400 volts, 50 Hz- Back gauge with positioning control ELGO ELECTRIC Type 85- Sheet metal holding device under the back gauge- Manual cutting gap adjustment with dial gauge display on the right and left- Stepless cutting length adjustment- Hydraulic

2-column hydraulic press SELF-MADEBaucy approx. 1980Compressive force 6 ton. at 180 barCompressive force 5 ton. at 150 barCompressive force 4 ton. at 120 barCompressive force 3 ton. at 90 barTable top 400 x 340 x 30 mmPlunger plate 410 x 350 x 28.5 mmTable usable area between the guide columns 305 x 245 mmPlunger stroke 140 mmInstallation height max. 320 mmColumn diameter 35 mmTable height above floor 1050 mmHydraulic operating pressure max.180 barMotor power 4 kWNet connection 380 volts, 50 Hz- stepless

Key data: 4040 mm, 4 mm

Max. cutting length: 4040 mm Max. sheet thickness: 4 mm steel Motorized adjustable backgauge with digital display up to 1000 mm Pneumatic sheet hold-up Side stop and table extensions Cutting length limitation Cut edge lighting Weight approx. 7500 kg

Key data: 5 t, 150 mm

Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed ​​(Approach Fast Speed: 350 (mm/s) Lower Speed ​​(Under Pressure Slow Speed: 36mm/s Rise Speed ​​250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size ​ Height (mm) 986 Width (mm) 485 Depth (mm) 920

Max. cutting length: 3100 mm Max. sheet thickness: 6 mm at 490 N/mm² Motorized backgauge with digital display Manual cutting gap adjustment Cutting length variably adjustable Cut edge lighting New knives

PRESS DESIGN   drive system: hydraulic   frame design: C-frame, single sided PRESS FORCES   total force (nominal): 12 to SLIDE   stroke: 200 mm ELECTRICAL SPECIFICATIONS   mains voltage: 380 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   total weight approx.: 1000 kg Hour counter: 30'181 h last safety check: 27.07.2023, overrun time 38 ms, overrun distance 60 mm

Haco PPM 100 ton x 3100 mm CNC Capacity: 100 ton x 3100 mm Backgauge: CNC Control: 2D Touch Passage between uprights: 2600 mm Max stroke: 120 mm Max distance between table -- ram: 325 mm Depth of throat: 250 mm Table width: 180 mm Locking speed: 70 mm/sec Working speed: 7,2 mm/sec Returning speed: 60 mm/sec Electric motor (power): 6 kW Length: 3270 mm Depth: 1550 mm Height: 2240 mm Weight: 7 ton

Haco PPH 135 ton x 4100 mm CNC Capacity: 135 ton x 4100 mm Backgauge: CNC Control: Delem DA-41T Passage between uprights: 3600 mm Max stroke: 120 mm Max distance between table -- ram: 325 mm Depth of throat: 250 mm Table width: 180 mm Locking speed: 70 mm/sec Working speed: 7,2 mm/sec Returning speed: 62 mm/sec Electric motor (power): 11 kW Length: 4270 mm Depth: 1500 mm Height: 2470 mm Weight: 9,1 ton

Key data: 3190 mm, 6 mm

Note: Machine is currently still being revised, the illustrations were made before the Revision. Sheet width: 3190 mm Sheet thickness steel: 6.3 mm Colour: grey Total power requirement: 18.5 kW Machine weight: 6800 kg Dimensions: 3830 x 3820 mm with cutting gap adjustment Stroke rates per minute: 30 - 50 strokes/min Angle stop: 1500 mm Throat: 5 - 1000 (1500) mm

CONTROLS   PC controller BECKHOFF PRESS DESIGN   drive system: servohydraulic   frame design: H-frame, tie rod   quick die change system: yes   feedstock transport direction: left to right SLIDE   total force (nominal): 1100 to   stroke: 130 mm   stroke rate (max.): 60 /min COUNTER RAM   nominal force: 330 to   stroke: 40 mm V-RING   nominal force: 500 to   stroke: 40 mm TOOL DIMENSIONS   lower table (left-right): 960 mm   lower table (front-back): 960 mm   upper table (left-right): 960 mm   upper table (front-back): 960 mm   shut height max.: 470 mm OVERALL SPECIFICATIONS (COIL LINES)   sheet width max.: 500 mm   sheet thickness max.: 16 mm   coil weight max.: 8 to   feedstock t ...

Hydraulic filter changer - FBM Falzoni brand - Size: Ø 160 mm - With 10 hp (7.5 kW) hydraulic group

sheet width: 3100 mm plate thickness: 6,0 mm thickness at Niro-steel: 4,0 mm distance between columns: 3100 mm down holder: 14 Stück oil volume: 150 ltr. cutting angle: 1,2 ° no. of strokes: 18 Hub/min control: CYBELEC CybTouch total power requirement: 11,0 kW weight: 6300 kg range L-W-H: 4.000 x 2.100 x 1.640 mm -------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be fol ...

pressure: 80.0 t stroke: 250 mm table surface area: 1040 x 260 mm column travel between the guideways: 1040 mm ajustment speed: 8.0 mm/sec working feed: 5.0 mm/sec return speed: 10.0 mm/sec engine output: 5.5 kW weight of the machine ca.: 835 kg. dimensions of the machine ca.: 1810 x 700 x 2100 mm Furnishing: - Robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed - Piston can be stopped in any position - Hydraulic tank mounted on t ...