electrical cable used for sale

KUKA KR16 built in 2006 Condition very good, as good as new only 65 hours of operation Reach 1611mm Weight 235 kg Payload 16kg Control KRC2 ed05 Weight 185 kg Software version V5. 5.10 KUKA KCP ed05 Connecting cable 7 m Availability immediately .

Wood chip dryer, firewood dryer for 4 containers The plant is abandoned due to conversion of the production. The plant is still in use today, so it can be visited in operation. The installation site was an all-round closed hall, so the system is as good as new and enables the economic use of heat energy. In addition, the electric feed-in tariff for the electricity generated in your CHP is improved. 3 cent CHP bonus according to EEG-2009 per kilowatt hour used. 4 containers of wood chips/firewood can be connected ( 35m3). Drying time wood chips: 4 days (fresh forest to 10% residual moisture) Drying time log wood (33cm): 5 days (fresh from the forest to 20% core moisture) System consists of: intake hopper for air incl. dust filter Blower unit (radial fan with motor 11kW) Heater 480kW Funnel for air flow incl. 4 shut-off valves and & 4 pieces connections Power con ...

KUKA KR360 control VKRC2 built in 2004 Condition good Reach 2900mm Weight 2245kg Load 360kg Control VKRC2 Weight 185kg Software version V4. 1 7 SP08 KUKA VKCP2 Connection cables 7 m or 15 m Availability immediately several available, preferably in larger quantities .

Lauber Energy Use Centre for 4 containers. The plant is abandoned due to conversion of the production. We replace our steam engine with a turbine, which is why most of the waste heat is eliminated. The plant is still in use today, so it can be visited in operation. The installation site was an all-round closed hall, so the system is as good as new and enables the economic use of heat energy. In addition, the electric feed-in tariff for the electricity generated in your CHP is improved. 3 cent CHP bonus according to EEG-2009 per kilowatt hour used. 4 containers of wood chips/firewood can be connected ( 35m3). Drying time wood chips: 4 days (fresh forest to 10% residual moisture) Drying time log wood (33cm): 5 days (fresh from the forest to 20% core moisture) The system consists of: Intake hopper for air incl. dust filter Blower unit Heater 370kW Funnel for air flow incl. 4 shut ...

NEW Bainite model BMIM95 95 litre intermeshing type mixer Customs Tariff CN Code: 8477.8093 Manufacturer: Bainite Machines Pvt Ltd Net chamber volume: 95 litre Rotor speed: 6 - 60 rpm Rotor type: HP-5 design (intermeshing) Dust seals: SSA (self-sealing arrangement) Motor power: 420kW, 1000rpm AC motor, 3ph, 50Hz, 380/400V Discharge door: Hydraulic drop door with linear actuator and toggle latch. Two (2) J Type thermocouples mounted in door top as standard One (1) Single acting pneumatically operated oil injector Feed Hopper Assembly: Hydraulically operated Floating weight: single ?V? bottom type Gearbox: Full unidrive type with S.F. 2.25 Bedplate: Fabricated steel Ancillaries: Dust stop lubrication (1.5HP x 2), hydraulic pump unit (20HP) Three (3) Zone closed loop temperature control (TCU) Electrical Controls: Schneider make variable frequency drive (VFD) controls with ...

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

Complete System YOM 1998 - installed 1999 - still in production - Avantra 44S with 3600 dpi - Online-Rapiline for Avantra44 - Basket, Cables, all complete System with Service-contract, complete tested and cleaned Available: in Produktion

1 x NEW 'Bainite' (India) Make 1000mm (42in) wide x 400mm (16in) dia two roll mill, Hydraulic nip adjustment (dual acting cylinders), Peripherally drilled chilled cast iron rolls (Hardness 65/72 Shore), with anti friction roller bearings, Friction ratio 1:1.08, Hinged guide plates, Lubrication system comprising pneumatic intensifier with grease reservoir, Electro pneumatic brake with power fail safe mechanism. Safety bars fitted to front and rear. Compact right angle drive with 45kW Siemens AC variable speed squirrel cage motor through heavy duty helical design direct drive reduction gearbox (SF 2), Back roll speed 18rpm/front roll 16.6rpm. All mounted on a compact design fabricated steel bedplate. Stainless steel tray underneath. Including electrical controls comprising Siemens G130 VFD drive and S7-1200 plc with HMI. CE marked, with full Technical file, Documentation and S ...

To separate and sort after the specific weight from light and heavy fraction. Useable for grain, aluminium/plastic, rubber/textile, cable-recycling, etc. Type and size are choiceable, depending on the product and throughput. At constant machine length, it is possible to choose between working width from: 450mm, 600mm, 900mm.

KUKA KR60-2 Built in 2001 Reach 2000mm Weight 867 kg Load 60kg Control KRC1 Weight 136kg Software version V4. 1. 7SP08 KUKA KCP1 Connecting cable 7 m Availability immediately .

Used line for the production of the co-extrusion by PST Forming method. PTI - The twin screw extruder DS 92/28   2x screws with a diameter of 92 mm The length of screws 28 x L / D Snails closed system with internal temperature control, deep nitrided, with degassing on the cylinder, extruder equipped with a vacuum pump with filter, Siemens Servo Motor power: 60 KW Torque: Nm 15700 Screw rotation: 0 - 50 rev. / Min. Zones with ceramic heaters with an intense cooling: 5 x 5 KW Cooling Zones: 4 Performance with hard PVC, depending on the materials and tools: max.600kg / h Length: 4500 mm Width: 1600 mm Height: 2300 mm           Extruder equipped with a microprocessor control SIEMENS type Extrusion Pro Pak visualization 2. Co-Extruder PTI - The twin screw extruder DS 68/28 Snails with a diameter of 2 x 68 mm Length of the screws: 28 x L / D Snails cl ...

GLIMEK Conical Rounder CR-400 GM - exhibition machine, brand-new condition, year of manufacture: 2022 - weight range 30 - 2.000 g, capacity range up to 3.600 pieces per hour, centrally adjustable track system, non-stick coating on cone and tracks, infeed at 6'00, outfeed at 12'00, track base plates made of food safe plastic, frequency converter drive for the cone speed, hot and cold air blowing unit, mechanical flour duster from stainless steel, 5 m connection cable and CEE-plug, power supply: 2.8 kW electrical connection: 400V/50-60 Hz/3~

If you are interested we will send you photos! MACHINE DESCRIPTION: The MAS tray packer is a packaging machine that folds and glues an open tray (from a cutting) around the product formation. FORMATION: The machine sets 2 x 5 = 10 Tetra packs per tray. Machine dimensions: 3500-4500mm long depending on infeed conveyor. 2008mm width; Height 2000mm Performance: max 10 trays/min Electrical connection: 5% 50 Hz, 3-phase, 230/400 volts, approx. 8kW Energy consumption: 6 kWh Frequency 50 Hz 2% active power 1.18 kW Volume < 80 dB Electrical equipment: brand products, in accordance with standard MAS machine no. 6017, built 06/2006 Cabinet: Make Rittal V2A firmly installed on machine Pneum. Equipment: Make Festo Glue device: Nordson (3.6 kg tank capacity) with 2 hose system; Glue order volume with proportinal valve Compressed air: 6 bar (dry, oil-free) Air consumption: approx ...

AKYAPAK ROUND BENDING MACHINE TYPE 90-10/3.0 MMIJ AS -Capaciteit 1050 x 3 mm -Electrically adjustable achterrol -Digital uitlezing -Roll Harde -Walsen Conisch -Bovenrol Wegdraaibare -Remmotor -Voetbediening -Noodstop -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (1 km from the German border)

1X Electrical power (Kw 0.73), Centrifugal force(kg) 680, Sieving decks 1 and sieve area (m2) 0.36

Price per piece; approx. 14 x conveyor belts rubber: approx. 0.50 m wide, approx. 6m long were electrically driven All prices are understood from station Europe and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been legally signed. Mistake reserved. All technical details, dimensions, etc. are approximate and are non-binding for the supplier. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty. We do not accept any liability for used material. Warranty exchange and return are excluded. The entire process of dismantling and loading as well as transport is carried out at the buyer's own expense and at the buyer's own expens ...

Machine completely reconditioned and repainted; Slitter rewinder with pneumatic unwinding and rewinding shaft, electrical lateral adjustment, working width 1320 mm, unwinding diameter 1300 mm, core diameter 76 mm, pneumatic brake Ortlinghaus, new upper and lower knives Still in operation: Yes

Robot KUKA KR30 3 TOP condition (new) Year 2012 Reach 2033mm weight 635kg load capacity 30kg control KRC2 ed05 weight 185kg Software version V5. 5.5 Language Windows XP Teachpendant KUKA KCP2 ed05 Connection cables 7 m .

Qty. 1 Second-hand ingot caster plantMfc.:Sistem TeknikBuilt:1/2015Stopped in 4/2015Recycling capacity:5000 Ton/annumQty. 12 Units of Pyrotek moldsDim. of aluminium ingot: 1000 x 1000 x 500 mmWeight:500 kgCharging material: Aluminium cans, profiles, sheets, motor blocks, wheels etc.Scope of supply:Aluminium shredderMagnetic separator Aluminium de-coating machine Baler Aluminium gas furnace Aluminium casting system Gas generator Mass ARUN spectrometer Air compressor, conveyors, forklift, ect.Shredder and magnetic separation conveyorMfc.:YSSType:Mono shaft shredder J600Capacity:500 kg per hour high power electrical shredding machineMono shaft shredder stylePLC automatic control unit Siemens?Hydraulic unit for material pushing to shredding wheelCurrent control for shredder reverse †safe usageShredded aluminium pass onto conveyor unitMagnetic separation system for steel removalElec ...

AGFA AccuSet 800 in great condition with Agfa Viper Rip, Resolution: 1200, 1800 and 2400 dpi - System includes all componentes: Accuset, Supply- & Takeup-Cassette, Apis-Cable, CDs, Software and Dongle. Including Techkon Densitometer for film. Just send us a mail and you will get more info and photos Available: now

KUKA KR6-2 Built in 2003 Reach 1500mm Weight 222 kg Load 6kg Control KRC2 Weight 185kg Software version V4. 1. 7SP08 KUKA KCP2 Connecting cable 7 m Availability immediately .

Machine details New Machines 4 Food Tumbler Mixer Model Uniball 225 Mixer Tumbler All stainless steel construction Capacity 225 litres, load capacity 60 kg to 100 Kg With inner blades to assist product roll Variable speed from 12 rpm to 24 rpm Motor gearbox drive 1.1 Kw Electric tipping discharge by motor gearbox Motor gearbox drive 0.12 kw Electric 400 volts 50 Hz Electrical controls mounted in IP 65 stainless steel control box Rigid construction to withstand movement Mounted on stainless steel wheels Discharge height to suit a standard 200 litre tote bin Overall length 1.6 metres Overall width 1.25 metres Overall height 2.0 metres Suitable for all type of products 12 months warranty

Mapelli 300ton downstroke hydraulic presses with vacuum, Type T300, year 1990, 4 column type, with pneumatic front guard, fixed guards to sides and rear, main ram dia 450mm, with pull back rams, single daylight 500mm, with 600mm wide x 700mm electrically heated platens. With hydraulic power unit mounted on top. Complete with controls etc and in good condition.

1 AUTEFA loose stock/flock stampfing press type 6.62 for stamping lose flock into materila carriers for dyeing / bleaching machines, with 2 stampfing arms with motorized rotational carrier support . complete with electrical panel

Finish securing distribution for Canalis KSA busbars up to 250. Equipped with Neozed 3x16A, for cable outlet. 67 PCs. available price per piece 8.-collection KLINGENBERG or plus shipping costs. Immaculate condition such as photo For details see under Raupp 0170 / 2204056. or at fa.raupp@t-online

Longitudinal stroke max. approx. 680 mm Transverse stroke Max 250 mm greatest distance spindle Center to table top approximately 525 mm Magnet size approx. 600 x 200 x 90 mm Disk size 300 x 50 x 76.2 mm Speed infinitely variable 1000--3000 U/min Dimensions, B x T x H approx. 3.2 x 1.8 x 2.5 m Spindle motor approx. 2.8 8.4 kW Weight of the machine CA. 3,3 tons Facilities: -with automatic vertical delivery -Roughing, Wiles, from fires and lifting by the adjustable potentiometers -Loading position is approached after slipping automatic -Rapid traverse across approx. 1.2 m/min via electric motor -Labour / rapid traverse along approx. 5 mm / min 40 m/min with servo motor and toothed belt drive -Rapid traverse vertical approx. 0.2 m / min -Digital display for lateral and vertical axis -Quick lifting system approximately 180 strokes / min -Straight electric, dresser with size and speed comp ...

Finish securing distribution for Canalis KSA busbars up to 250. Equipped with Diazed, for cable outlet. 9 PCs. available price per piece 39.-collection KLINGENBERG or plus shipping costs. Immaculate condition such as photo For details see under Raupp 0170 / 2204056. or at fa.raupp@t-online

The fishing and packing plants have a simple and this stable and torsion-free construction. The machines are characterized by ease of use, flexibility, reliability and low maintenance requirements. The CAMBORIT clip has a capacity of up to 125 packs / min. 1 x 2 bottles can be packed with the CAMBORIT clip. To do this from flat so called "bars" cut to shaped, that get caught under the edge of the bottle. The machine can be operated automatically or manually. Display and operating elements are located on the control panel. All functions are controlled from the control panel and controlled. Errors of the cycle are displayed on the control panel. Action: At the beginning of production the magazine must first cut to be filled. The minimum level is cut to the magazine below, the machine will not turn on. After switching on the machine when existing minimum level of bottles with a capac ...

Technical data: Capacities: Height of centres over the flat way: 625 mm Height of centres over the flat floor: 1225 mm Swing over bed: 1250 mm Swing over carriage: 940 mm Diameter of four-jaw chuck: 1250 mm Only range of the chuck min/max: 230/1050 mm Distance between centres: 5000 mm Headstock: Spindle bore: 105 mm Spindle seat: cyl. 105 Diameter of the spindle in the front bearing: 320 mm Number of spindle speeds: 24 Overall range of spindle speeds: 1.6-315 rpm Spindle drive motor rating: 75 kW Maximum torque of the spindle: 63000 NM Carriage: Of the bed width: 1100 mm Length of the saddle: 1320 mm Of the cross slide width: 550 mm Travel of cross slide: 800 mm Travel of tool slide: 600 mm Number of feed Council for each range: 20 Overall range of longitudinal feed Council: 0.18-160 mm / rev Range of longitudinal feed Council at: -high range of spindle speeds:  ...

CHP Schmitt enertec V12 Hi here sell a Schmitt enertec BHKW that is immediately ready for use and can also be tested prior to sale. Transport or construction is also possible. Electrical power: 300 kw with internal charge air cooler circuit 370 kw at external charging air cooler circuit Thermal power: 408 kw to 300 kw el. Required fuel: Bio-gas gas Sewage gas Landfill gas Special: Compact design in soundproofing hood with supply and exhaust air installed motor control cabinet to the frame: Engine one E2842 Leroy Somer operating hours: ca 100 Description: The CHP has been completely dismantled and rebuilt, which means the motor and generator have been overhauled. Control: PPU is by Deif SPS is by Telemecanique If you need replacement parts or have questions I am under to you provided: With friendly regards Andreas Peters Andreas Peters CHP GmbH & Co.KG Repairs of engines ...

Seydelmann K 90 DC-8, 90 liters bowl cutter, all stainless steel, variable knife speed, 2 bowl speeds, variable mixing speeds forwards and reverse, knife shaft brake electrically operated, noise reduction cover, loading device, unloader, in very good condition. The machine is immediatley available and can be tested in our facility in Koblenz, Germany.

Press 800 x 800 clamping force cca 3000kN electrical heated

1 factory-tested, well preserved two girder magnet overhead travelling crane with helical wire-stabilized trolleys for magnetic-beam operation Load approx. 2 x 3.200 kg = 6.400 kg Wingspan approx. 18,720 mm Hook way about 10,000 mm Make chairs / DEMAG Year of production / workshop testing 1991/2016 FEM 3 M Hubklasse H 3 Beanspruchungsgruppe B 5 Crane equipped with 2 movable separately and together, inclined cable stabilized DEMAG double girder trolleys with 2 elevators, radio control, magnetic control and shape steel magnetic system with 2 groups of â 2 magnets to the transport of long material and concrete steel Working speeds: Hoist around 2.1/12.6 m / min Cross travel approx. 10.0/40.0 m / min Crane drive approx. 0-80.0 m / min

Delivery time: 2 weeks Length: 350 mm Width: 470mm Height: 480 mm Capacity: 8 litres Weight: 20 kg Kw: 0.1 Operating instructions: german Description Pastry filler of manufacturer IZO is an electrical machine for dosing and injection of cream and jam. The machine is designed for professional use in bakeries and pastry shops. -Digital Control Panel - cooler - automatic time dosage

Specifications (manufacturer): -Manufacturer: Miele / Germany -Model/type: T 6250 - Fabrikationsnr.: 25375347 -Part No.: 52625001 -Built in _ -electrical connection: 3 ~ 380V 50 Hz 10.0 A -electric power consumption approx. 14.30 kW -Re circulation dryer exhaust air recirculation with automatic reversing system -Drying capacity: 10 kg in 35 min cupboard dry -electronic measurement of residual moisture -large filter with optical display -Crease protection -Capacity dry: 10 kg / filling ratio 1:25 / 1:20 -Evaporation performance max 13,5 L / h -2 Motors (drive and blower) -Drum capacity: 250 L -Heating capacity: 13, 5kw switchable to 9kw -Exhaust air connection 150 mm -Dimensions (Lxwxh): approx. 900 x 805 x 1390mm -Weight 147 kg

Dimension of sliding table- 1600x375mm Gross cut capacity- 1500mm Width of cut between saw blade and rip fence - 1140mm Saw blade diameter - 400mm Height of cut (90°) - 115mm Height of cut (45°)- 105mm Speed of main saw spindle - 4500/6000rpm Main spindle diameter - 30mm Tilting saw blade - 0-45º Saws lifting, up and down, electrical control. Main motor - 5,5 kW Scoring saw blade diameter - 120mm Speed of scoring saw blade - 7000-8000rpm Scoring saw diameter - 20mm Scoring motor - 1,1 kW Weight: 650 kg Transport dimensions - 1800x1000x1200mm Using the blade 400mm, the smaller should be removed. Reduced saw blade should be used with not more than 350 mm main shield.

Weibert WJ-F50 Table milling machine NEW Safety rulers in the shaper fence strongly ribbed cast iron table 1100x900mm electrical height adjustment 200 mm 5.5 KW R + L barrel 3000 to 10000 U/1 Control Panel top Milling spindle can be exchanged Tool - diameter When profiling 275mm at the tenoning 400 m stable role statement WJ-600600 K 4 Special price:

? The machine is built in 2 construction works: 1250 x 2500 and 1500 x 3000. ? The IPG fiber laser resonator is available for this model with the power values 500 W, 1000 W, 1500 W and 2000 W. ? The beam is guided by a flexible light guide, i.e. cleaning and alignment of the mirror optics are not required. ? The HP SSL high-performance cutting head is very easy to set up. ? High cutting efficiency with low operating costs; Power consumption of only 13 kW for a 1-kW fiber laser source. ? The heavy machine frame and the high-stiff bruecke are designed as a tension-free welded construction and carefully manufactured. ? The interchangeable table with hydraulic lifting adaptation takes over the loading and removal of cut parts during the ongoing cutting process - re-training with further automation functions is possible. ? The working area is fully clad and illuminated, and the cutting ...

Preliminary operating machine for year QIV/2013, 100 operating hours Basic 1530 Basic Waterjet Processing Centre 1530 Working area: X-axis 3050 mm Y-axis 1550 mm Z-axis 150 mm The abrasive water jet cutting requires the addition of a supplied abrasive cutting head. This reduces the distance between cutting head and factory tool. drives: drive side, reverse play-free linear drives in X and Y are used with stoeration-free CAN-BUS communication as well as guide well-known manufacturer. This This means maintenance and wear-free operation of the system and the long -term Drive unit X-axis is mounted on granite. Individual linear units are protected by folding beam and covers in addition to the ingress of dust and water. Accuracy: 0.05 mm / Working area Max.Speed: 15,000 mm/min Z axis German-speaking operator software for machine control Abrassiv de-sludge plant ...

Important and distinguishing design features of the RaptorX SL steel base machine / gantry RaptorX-SL1200/S20 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method t ...

Technical data: Kreuzmayr Obsttrockenschrank OTS 22, 22 m² surface dry, electrically heated, with temperature and humidity control power 7.5 of kW, full stainless steel for drying fruits, vegetables, meat,... Condition: new (Errors and omissions in the technical data, information and prices and subject to prior sale.)

Various spare parts for SOMOS dryers e.g.: gear wheels, electrical parts, desiccant Chambers, filter elements, blowers, heating elements, motros, sight glasses, turbines, magnetic valves or cylinders can be offered on demand.

Tip height: 330 mm centre distance: 1500 mm circular diameter: bed 690 mm spindle bore: 82 mm spindle retainer: short taper size 8 taper tailstock: 6 MK spindle speed: 7.1-1400 rpm feeds: longitudinal/plan 0.05 112/0.025 56 mm / U thread pitches: 0.25-560 mm electrical connection: 380 V, 15 kW space: 3350 x 1800 x 1400 mm weight: 4800 kg

Important and distinguishing design features of the RaptorX SL steel base machine RaptorX-SL3200/S15 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objec ...

Specifications / Technical Data S-1000 CNC-Fraese and Engraving Machine The almost largest CNC machine in the High-Z series. With an external dimension of approx. 1350 x 800mm still handy enough and extremely powerful. With the High-Z CNC unit, they acquire an all-round talent in TUeV-certified quality (EMC). Whether you want to clamp complex parts on a groove table or, or to clamp factory tins into a high vice (the machine is on a frame construction, is driven in X via 2 motors and thus allows to be placed completely over a part to be machined). or simply want to do engraving or drilling then they simply work on a flat base, on which they then attach e.g. an MDF plate, which they once overfrave plan and are then able to work up to approx. +-0.02mm exactly in depth. All CNC portal fraes machines are supplied with coloured energy chains on all axes due to the improved cable guid ...

Specifications / Technical Data S-720 CNC-Fraesmaschine With the High-Z CNC-Fraes.- and Engraving Machine you acquire an all-round talent in TUeV-certified Quality (EMV). Whether you want to clamp complex parts on a groove table or, or put factory tins in a high vice (the machine is on a frame construction, is driven in X via 2 motors and thus allows to be placed completely over a part to be machined). or simply want to do engraving or drilling then they simply work on a flat base, on which they then attach e.g. an MDF plate, which they once overfrave plan and are then able to work up to approx. +-0.02mm exactly in depth. All machines are supplied with coloured energy chains on all axes due to improved cable guidance. Furthermore, all machines are protected with a double-secured emergency exit button. Another is located directly at the controller. Basic equipment of all high- ...

Tip height: about quilt 300 mm centre distance: 1500 mm circular diameter: upper bed 640 mm spindle bore: 67 mm spindle retainer: Gr. 8 taper tailstock: 5 MK spindle speed: 18 - 900 rpm feeds: longitudinal/plan 0.063 0.032 2.1 mm / U thread pitches: 0.5-14 mm electrical connection: 380 V, approx. 7.5 kW space: 1550 x 3100 x 1250 mm weight: approx. 3500 kg hardly used and therefore well-preserved bed lathe

Important and distinguishing design features of the RaptorX SL steel base machine RaptorX-SL2200/S20 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce ...

Tip height: 107 mm top width: 350 mm circular diameter: bed 200 mm spindle bore: 25 mm taper tailstock: 2 MK spindle speed: 35 - 3500 rpm feeds: longitudinal and mm/U thread pitches plan: 0.2-3 mm electrical connection: 380 V, approx. 2.2 kW space: 600 x 1300 x 1230 mm weight: 850 kg

Important and distinguishing design features of the RaptorX SL CNC Router steel base machine RaptorX-SL2200/S15 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction metho ...