130,501 used machines on RESALE, but how to find them? Machine Search
The machine is in good technical condition, an inspection by prior arrangement is possible. Max. turning diameter: 465 mm Max. circumferential diameter: 680 mm Max. rotation diameter via cross slide: 465 mm Max. width of the cross-section: 315 mm Travel in X/Z: 300/1050 mm 315mm 3-Jaw Hydraulic Chuck Max. spindle speed: 3250 rpm Spindle bore: 76 mm Spindle drive power (40%/100% ED): 33/22 kW Max. spindle torque (40%/100% ED): 630/420 Nm Max. speed driven tools: 4000 rpm Programmable tailstock, tool measurement, chip conveyor S/No. 8045000336E (2011) Installed power: 50 kVA Power supply: 400 V; 50/60 Hz Dimensions (L x W x H): 5250 x 2300 x 2000 mm Machine weight: 8000 kg
Aircooled chiller/Heat pump EMICON PAE 4902 S KC 488 kW / 570 kW Cooling capacity: 488 kW / 138.76 tons (12/7 — 35°C) Heating capacity: 570 kW / 162.08 tons (40/45 —7°C) Year of manufacture: 2013 Options: Heat pump. Hydraulic module. Recuperation. Refrigerant circuit: 2 pcs. Heat exchanger: Plate Condenser: Copper / Aluminum Compressors: 3 pcs. Copeland ZP385KCE-TWD 522 (scroll) + 1 pcs. Bitzer GSD80385VAB4-2 (scroll) + 2 pcs. Bitzer GSD80295VAB431 (scroll) Type of refrigerant: R410a Number of fans: 8 pcs. (EC-fans) Hydraulic module: 2 pcs. water pump Wilo DL80/160-11/2, expansion vessel. + 1 pcs. water pump Wilo IPL65/170-1.1/4 (Recuperation) Dimensions: 4.85x2.3x2.56 m Weight: 4495 kg Condition: Good
Working widths: 2000 mm roll surface width: 2200 mm Fabric content: 48 Meter 0: 160 mm Roller covering: ALU Clouth speed: 20 - 200 m/min Cloth tension: 20 - 500 N voltage: 400 V / 50 Hz output: kw weight: t dimensions of the machine ca.: m cloth accumulator: 48 meters capacity Number of rolls: 15-axis guide rolls, Ø 160 mm made of aluminum type of material: double polyamide foil hose material thickness: 2 x 15 my to 2 x 50 my movable roller mill is moved up and down with 4 ball screws unit was disassembled after test run for transport The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 400 mm y-travel: 300 mm z-travel: 300 mm control: Jasnac tool taper: BT30 Tools changer for 12 tools: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 370x32x3 mm : 15-150 U/min vice: 190 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 110 mm capacity 90 degrees: flat: 180x100 mm : 115 mm : 90 mm : 90x90 mm : 115 mm : 100 mm : 120x100 mm : 115 mm : 100 mm : 120x100 mm total power requirement: 5,5 kW weight: 615 kg Overall size: 1400x1400x2000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
ESTA SLDG 800, used refrigerator Used refrigerator with sliding glass doors Esta refrigerator SLDG 800 – the ideal solution for efficient cooling. With a capacity of 776 litres, space-saving sliding doors and adjustable grates, it offers maximum use of space. Tropicalized unit and convection cooling system guarantee reliable performance at +3°C to +7°C. • External dimensions (H x W x D): 204 x 114 x 63 cm • Interior dimensions (H x W x D): 114 x 105 x 50 cm • Usable volume approx. 756 litres • 6 adjustable shelves • Convection cooling • Internal temperature control range: +3 to +7° C • Interior: sheet steel • Outer material: sheet steel • Refrigerant: R134a • Plug-in ready (220-240 V/50 Hz, 5.5 A) • Door made of thermoglass •Indoor We would like to point out that with regard to the Product Safety Regulation, the product offered here is int ...
dimensions of saw-blade: 350 x 32 x 3,4 mm : 1700/3400 U/min capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 105 mm capacity 90 degrees: flat: 180x70 mm capacity 45 degrees: round: 120/110 mm capacity 45 degrees: square: 100/95 mm capacity 45 degrees: flat: 135x60 mm output: 1,5/2,2 kw weight: 280 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 10 mm cutting angle: 2 ° down holder: 14 Stück no. of strokes: 13 Hub/min throat: 350 mm oil volume: 260 l total power requirement: 22 kW weight of the machine ca.: 10.550 kg dimensions of the machine ca.: 4000x2250x2050 mm Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTe ...
sheet width: 3100 mm plate thickness: 6 mm voltage: 380 V control: CYBELEC CybTouch down holder: 14 Stück cutting angle: 1,2 ° total power requirement: 11 kW weight of the machine ca.: 5700 kg dimensions of the machine ca.: 4000x2100x1640 mm Accessories / equipment: - CYBELEC Cybtouch touch screen controller - NC controller for backgauge, gap adjustment, number of pieces, cutting length - 1 side stop with scale, T-groove and tilting cam - 2 front support arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Folding finger guard with limit switch - motorized back gauge 1.000 mm travel - Ball screws - Photocell behind the machine - Ball rolls in the table - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - CE mark / Declaration of Conformity - Operating manual: Machine and control in German The data for this ad was created with ModulMWS ...
AMADA EUROPE 255 CNC punching machine was built in 2004 in France by AMADA EUROPE S.A.. The machine, designed for machining thin sheet metal of a maximum thickness of 3 mm, is distinguished by its high efficiency and reliability. In order to obtain the highest precision of the produced parts, all the machining processes are performed on a large brush table. This table, thanks to its design, prevents scratches and nicks on the sheet metal during the material feed, and also significantly reduces the noise level. The EUROPE 255 punching machine is also offered with extensive equipment, including e.g. a cooling unit, light curtains and an advanced GE FANUC CNC control. The total weight of the machine is 11000 kg. Technical specifications of the AMADA EUROPE 255 punching machine - maximum press force: 20 t (200 kN) - feed in the X/Y axis: 1280/1320 mm - feed rate in the X,Y axis: 82 m/m ...
Distillation plant for WFI water or pure steam generation Manufacturer : DEWA Type: DP 30 EVS Technical specifications : Distillation or pure steam plant this system can be used to produce either distillate or pure steam. Production 30 litres/h Feed water consumption 35 l/h Cooling water consumption system at 95 °C Destwasser 200 l/h electric heating capacity 18 kW max. operating pressure 1.9 bar min. cooling water pressure 1.0 bar min. feed water pressure 1.0 bar min. pressure for control air 6.0 bar Total capacity evaporator approx. 27 litres Evaporator capacity at max. level approx. 11 litres Dimensions: Height 2240 mm Width 970 mm Depth 700 mm Empty weight 300 kg Documents: available
; Gross weight [kg]: 5230; Engine: Perkins 2506A-E15TAG1; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775
sheet width: 3100 mm plate thickness: 6 mm voltage: 380 V control: CYBELEC CybTouch down holder: 14 Stück cutting angle: 1,2 ° total power requirement: 11 kW weight of the machine ca.: 6.300 kg dimensions of the machine ca.: 4000x2100x1640 mm Equipment: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. can be folded up at max. Traverse path, for longer cuts - 1x side stop - 2x front support arms - Ball casters in the front support table - hinged finger protection, with safety switch - BOSCH / HOERBIGER hydraulic system - SIEMENS electrical system - light barrier behind the machine (safety device) - fo ...
sheet width: 3100 mm plate thickness: 13 mm thickness at Niro-steel: 8 mm control: CYBELEC CybTouch down holder: 14 Stück cutting angle: 2,0° ° no. of strokes: 11 Hub/min voltage: 380 V total power requirement: 22 kW weight of the machine ca.: 12.100 kg dimensions of the machine ca.: 4000x2240x2235 mm Accessories / equipment: - CYBELEC-CybTouch control panel with digital display for backgauge - hydr. Cutting gap adjustment via control - 1 side stop - 4 front lifting arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Ball rolls in the table - motorized back gauge 1.000 mm travel with recirculating ball screws, automatically start at the end of the stop - Shear knives for stainless steel cuts as standard - Photocell behind the machine - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - Operating instructions in German The data f ...
clamping force: 1.750 kN injection volume: 318 cm³ screw diameter: 45 mm platen size: 700 x 700 mm daylight between platens - max.: 460 mm Condition: used, Specification: Horizontal injection moulding machine, Injection unit: - Screw diameter: 45 mm - Screw length L/D: 20 - Spray volume: 318 cm³ - Shot weight max.: 287 g - Special spraying pressure: 2,100 bar Clamping unit: - Max. clamping force: 1,750 kN - clamping plates: 700 x 700 mm - Opening path max.: 460 mm - mould installation height: 150 mm - Operating hours: 89217 h - 1x core puller - Handling / Robots: ENGEL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Finnrose Plate Stacker Type ST-10-170 Electronic For automatic stacking (e.g. on roller conveyor for further transport) Of plate-shaped workpieces, doors, or woods Was used to stack timber behind a four-sided planer Workpiece size Maximum 2500 mm x 800 mm Minimum 400 mm x 250 mm Weight maximum per workpiece 80 kg Capacity 20 workpieces per minute, depending on the workpiece size Maximum stacking height above floor 1800 mm Belt drive 0.18 kW Roller drive 0.09 kW Compressed air consumption per stroke 3.9 NL Instruction manual and circuit diagram available Weight approx. 600 kg Dimensions 2800 mm x 2200 mm x H 1100 mm (H max. 1800 mm)
; Gross weight [kg]: 5395; Engine: Perkins 2506C-E1STAG2; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775
Tool holder VDI 30 longitudinal holder Interface size square 20x20 3.3020DSS left overhead Cantilever length (LPR) 100.00 mm Functional length (LF) 0.00 mm Operating height (HF) 20.00 mm Functional width (WF) 36.00 mm Clamping length, max. (LSCX) 100.00 mm Direction Tool Holder (HAND) L Number of holders, workpiece side (CCONWS) 1 Product Categories Static Tools and Adapters Product type square holder Shaft size VDI30 Square Interface Size 20x20 Convertible No Rotatable main and sub-spindle No Tool orientation 0° Price without VAT Link to the product on the manufacturer's website: ttps://ews-tools.de/de-DE/product/ews-3-3020dss-laengsaufnahme-stahlho ehe-20-din-69-880-form-c4-links-ueberkopf-/69496 Condition: New
Tool holder VDI 30 longitudinal holder Interface size square 25x25 2.3025G300 right overhead Cantilever length (LPR) 70.00 mm Functional length (LF) 0.00 mm Working height (HF) 25.00 mm Functional width (WF) 17.00 mm Clamping length, max. (LSCX) 70.00 mm Direction Tool Holder (HAND) R Number of holders, workpiece side (CCONWS) 1 Product Categories Static Tools and Adapters Product type square holder Shaft size VDI30 Interface size square 25x25 Convertible No Rotatable main and sub-spindle No Tool orientation 0° Price without VAT Link to the product on the manufacturer's website: ttps://ews-tools.de/de-DE/product/ews-2-3025g300-laengsaufnahme-stahlh oehe-25-/28007 Condition: New
Hydraulic balancing act with cooling and tank (0.70 cbm) Motor 37 kW, filter, pressure vessel, etc...
max. workpiece length: 4500,6000 mm profile spindle: 3 Stück main drive: 24 kW Control: Siemens 840d Working Process Logos Life Evo XS 2345 ------------------------------- Vollautomatisches CNC-Fensterfertigungsanlage mit automatischer Be- und Entladung. 2 Portale mit 3 Frässpindeln mit 4- und 5-Achstechnologie CNC-gesteuerter Manipulator für Werkstückpositionierung mit 16 Stück Doppelzangen 8 Stück komplett unabhängige Werkstückspanner für höchste Felxibilität und Produktivität 128 Werkzeugplätze NEU: Working Process baut nun auch 1-spindlige Anlagen mit bewährter Technologie für kleinere Betriebe! Nebenstehend finde Sie aktuelle Videos dieser Baureihe. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 400 mm workpiece weight: 315 kg table height: 360 mm max. height (90° position): 635 mm height of the swivelling axis: 240 mm distance table center - swivel center: 485 mm center bore: 40 mm rotation movement: 360 ° reading accuracy of turning index: +/-4 ° swivel movement: 90 ° power capacity: kW weight of the machine ca.: 0,31 t dimensions: 850x450x360 mm • new-valued, manual operated, swivelling rotary indexing table, • H4 = indicating system for circular movements 0 - 360 ø +/- 4 above optic, • S20 = indicating system for swivelling movements 0 - 90 ø +/- 20 above scale ring, • B = manual operation for 0 - 360 ø, • B = manual operation for 0 - 90 ø, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
welding current: 10 - 180 A open-circuit voltage: V connected load frequency: 230 V weight: 6,8 kg Dimensions (LxWxH): 403 x 153 x 264 mm Accessories for inert gas welding machine: Hose package 4m. Earth cable 4m Accessories for inert gas welding machine: Hose package 4m. Ground cable 4m Welding wire 1 roll, Pressure gauge Welding wire 1 roll, Pressure gauge With nozzle and gas nozzle List price: 2200, -EUR The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
mechan. Oil Mist Separators - Volume flow: up to 1200 m³/h - Electrics: 3-Ph. 400 V - 50/60 Hz - Power: 1.5 kW (IE3) - Current: 2.3 A - Protection class: IP54 - Noise: 70 dB
Technical data for the workbench: Manufacturer: Dexion Type: Speedlock P90 Dimension: Width: approx. 1,350 mm Height: approx. 938 mm Depth: approx. 820 mm The scope of delivery includes: 02x Workbench stand, used Material colour: sendzimir galvanised Stand height: 900 mm Stand depth: 800 mm Stand profile: 100 x 100 x 3.00 mm Incl. cross and diagonal struts, base plates The stands are pre-assembled ( bolted truss ) 04x Workbench trusses, used Material colour: sendzimir galvanised Box profile: 100 x 50 mm Truss Type: BX100/50/15 Clear width: 1,140 mm 08x Safety pins, used Design: completely galvanized 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,350 mm Particleboard depth: 820 mm Particleboard one-piece 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,120 mm Partic ...
Technical data for the workbench: Manufacturer: Dexion Type: Speedlock P90 Dimension: Width: approx. 1,665 mm Height: approx. 938 mm Depth: approx. 820 mm The scope of delivery includes: 02x Workbench stand, used Material colour: sendzimir galvanised Stand height: 900 mm Stand depth: 800 mm Stand profile: 100 x 100 x 3.00 mm Incl. cross and diagonal struts, base plates The stands are pre-assembled ( bolted truss ) 04x Workbench trusses, used Material colour: sendzimir galvanised Box profile: 89 x 50 mm Truss Type: SLO089|2 Clear width: 1,445 mm 08x Safety pins, used Design: completely galvanized 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,665 mm Particleboard depth: 820 mm Particleboard one-piece 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,425 mm Particleboard dep ...
Technical data for the workbench: Manufacturer: Dexion Type: Speedlock P90 Dimension: Width: approx. 1,350 mm Height: approx. 938 mm Depth: approx. 820 mm The scope of delivery includes: 02x Workbench stand, used Material colour: sendzimir galvanised Stand height: 900 mm Stand depth: 800 mm Stand profile: 100 x 100 x 3.00 mm Incl. cross and diagonal struts, base plates The stands are pre-assembled ( bolted truss ) 02x Workbench trusses, used Material colour: sendzimir galvanised Box profile: 89 x 50 mm Truss Type: SLO89|2 Clear width: 1,140 mm 04x Locking pins, used Design: completely galvanized 01x Particleboard, used Particleboard thickness: 38 mm Particleboard width: 1,350 mm Particleboard depth: 820 mm Particleboard one-piece 06x Self-drilling screws, new Design: galvanized Dimensions: 6.3 x 70 mm The pict ...
weight max. in kg: 800/400 kg stroke: 6/12 mm stroke speed: 5/8 m/min output: 1,25 kw connected load frequency: 230 V weight: 21 kg dimensions: 420 x 180 x 280 mm Due to the low installation height, the maximum lifting height remains available. Control with emergency stop. (required by law) Suspension with safety hook. Overload protection with slip clutch. Built-in limit switch. Collection bag for chain. Control console with 1.6 m cable. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mm table width: 1500 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 1,5 t dimensions: 3,0 x 1,5 x 0,9 m Welding table SIEGMUND Professional Extreme 850 + plasma nitrided is made of high quality steel S355J2 + N and is plasma nitrided. Surface hardness max. 850 Vickers. The table has a material thickness of approx. 24.5-27mm. The holes have a diameter of 28mm. Hole arrangement in 100 mm grid on the table top, parallel hole arrangement in 50 mm grid on the sides. Including basic equipment. Accessories shown are optional. Price plus packaging and transport. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
maximum number of results exceeded
please refine your search
