drying tower used for sale

- Producer Venjakob - Type VEN DRY OIR 38/40 - Year of construction 2013 - Working width 1.300 mm - Working height 940 + - 20 mm - Length of flash off tunnel 3.800 mm - Fresh air 100 m³/h - Exit air ~ 500 - 1000 m³/h - Circulation air ~ 3.000 m³/h - Drying temperature ~ 30 Grad - Air speed 0,5 - 2 m/s - IR-tube emitter 12 Stk. - Power IR tube emitter 12 x 1,5 kW - Transport belttransport - Length 4.000 mm - Location, in stock - Voltage / HZ 400/50 - Voltage fluctuation max. +/- 5 % - control cabinet with Touch-Screen mit neuer Siemens Steuerung 1 Stk.

This is a granulate dishwasher from the manufacturer Wexiödisk, type WD-100GR from the year of construction 2016. Wexiödisk granulate pot dishwashers clean all stainless steel kitchen utensils with water added to plastic grains. Even burnt-in grease can be removed quickly and easily. The dishes do not need to be soaked or scrubbed; only loose food residues are scraped off to avoid unnecessary contamination of the rinsing water. Thanks to the unique, double-door push-through system, the WD100GR differs from all other pot washers on the market; The dirt and clean sides are completely separated from each other. The scope of delivery includes the inlet table, the cassette trolley and two cassettes. The inlet table is equipped with a water faucet and a hose holder, so that a hand shower can be installed quickly and easily for pre-rinsing. The dishwasher has undergone a major predictive insp ...

Vacuum oven, Volt: 230, Elec: 230 V 800 1/N/PE Watt 50 Hz, Link to manufacturer: https://www.renggli/en/laboratory-devices/drying-and-incubation

CONTINUOUS DYEING RANGE, MAGHEBA ROLLER WIDTH 625MM HEATING SYSTEM GAS LAYOUT IN LINE 2 ROLL FINISHING PADDER 625MM DRYING CYLINDER 800X1250MM LAIT OUT FOR GAS HEATING DANCER DEVICES BETWEEN THE CYLINDERS TAKE-OFF DEVICE WITH 3 STATION, 1250MMWIDE SEPARATE CONTROL DESK + PLUG CONNECTIONS

Large capacity mixer. Its condition is of occasion equipment completely revised and reconstructed, in its entirety (re-release) guaranteed. the mixer, mixer, vacuum massager of the Spanish manufacturer Sia, model AM-352-A. Characteristics: they consist of a cylindrical container and hemispherical bottom, inside which and in the middle of an intense vacuum, some blades rotate (in both directions, at will or automatic), which produce a double movement of the paste, in crossing and alternative overlap, which allows kneading, mixing and massaging all kinds of pastes, without pressure, without friction, Bruising or harmful heating, in addition to distributing perfectly and in a minimum of time, all the components of the mixture. These qualities stand out above all the kneaders-mixers-massagers on the market. On the other hand, and as a consequence of the depression created and the extracti ...

Fully functional FARO Arm Measuring Arm Prime High Precision 3D Measuring Instrument Quality Control Year of construction: December 2012 Certification date: August 2014 Number: R04-02-12-28398 Single Point: 0.016 mm Volumetric: +/- 0.023 mm Made in Germany The Best Portable Coordinate Machine (CMM) High Measurement Accuracy, Measurement Stability Reduced inspection times, automatically generates reports Ready to use in a few seconds Measure parts and assemblies quickly, easily and precisely Ideal for complex measurement tasks Solid measuring plate with trolley table, 336 kg Drawer with key Degree of accuracy: DIN 876/1 Permissible deviation: 0.02 mm Actual deviation: 0.00589 mm Checked on 05.03.2013 Made in Germany With various accessories Measuring arm case HP PC Tower Screen Keyboard Lots of software e.g. Cam2 Measure 10, Nvidia Graphics, Windows, HP

Key data: 320 mm, 600 mm, 5000 1/min

Machine Details Stock-No. 1105-03934 Type of machine CNC Lathe - Inclined Bed Type Make GILDEMEISTER Type CTX 420 LINEAR Year of manufacture 2002 Type of control CNC Storage location FRANCE Country of origin Germany Delivery time available at short notice Freight basis ex Showroom Technical details turning diameter 320 mm turning length 600 mm turning diameter 320 mm control Siemens 840D Travel -X Axis 260 mm Travel -Z Axis 635 mm swing diameter 680 mm swing diameter over slide rest 365 mm Spindle Bore Diameter 87 mm Turret (X-Stations) 12 MainSpindle Speed 5000 1/min Rapid Traverse X + Z Axis 24/30 m/min drive capacity - spindle motor 21 kW connected load 40 kVA dimensions 4,32 x 1.72 x 1,77 m Additional information CONTROL SIEMENS 840D WITH SHOP TOWER NICE MACHINE WITH LINEARTECHNIK

ENGEL INSERT 60H/30 SHUTTLE injection moulding machine was manufactured in 2016 in Austria. A specialised machine with a small footprint, is used for, among others, the overmoulding of inserts and the joining of various materials such as glass, metal and electronics. Thanks to the electric control of the injection unit and the ‘pressure locking’ system for the injection cylinders, the injection moulding machine guarantees high repeatability and excellent quality of inserts. The ENGEL INSERT 30 injection moulding machine allows you to set the speed and clamping force to prevent damage to the mould. Once both mould halves are closed and a high closing force is generated, the injection unit pushes the nozzle against the injection sleeve of the mould and produces an adjustable clamping force. At the end of the cycle, a very powerful screw with a diameter of 18 mm injects the melt unde ...

Bausch complete vial line including labelling and inspection in „as-new condition comprising: Bausch type 721 De-bagging machine for vial tubs size 221 x 379 x 49.5 mm, with oRABS Bausch type 411 enclosed sterile transfer chamber to decontaminate outer surfaces using 4 UV light lamps Bausch type 721 De-lidding and de-nesting of the vial tubs under isolator Bausch type 534 filling and closing machine for stoppers/rubber bungs, operates under class A conditions into an isolator for toxic products, rotary infeed table, pre- and post-weighing for the In-Process Control (IPC) of a 100% weight verification of each vial, pre-gassing with nitrogen, dosing using 4 peristaltic pumps with a filling accuracy of up to +/-1% Bausch type 551 closing machine for aluminium crimp caps and flip-off with rotary infeed table, under isolator Bausch type 309 cleaning machine for external washing, rinsi ...

1 x Vacuum calibration unit for profiles Manufacturer: Battenfeld Type: K-400-V4 Year of construction: 1992 Total length: 6700 mm Vacuum connections: 4 x 8 pieces Water connections: 26 pieces Vacuum pumps No.1-3: 3 pieces of BluVac pumps from Speck, Energy-saving vacuum generation thanks to patented speed control Pump power: 3 x 4.3 kW Vacuum pump No. 4: Speck (5.5 kW) Longitudinal adjustment: electromotive Connected load: approx. 26 kW Accessories: 1 x water pump (1.5 kW) for the water circuit, 1 x blower (0.95 kW) for drying the profile,

Sheet metal deburring machine Manufacturer: ERNST Type: EM5/N900 Year of construction: 1999 Control type: conventional Working width: 880 mm Workpiece height: 1-70 mm Grinding drum diameter: 420 mm Machine weight approx.: 2,800 kg Dimensions approx.: 2,500 x 1,715 x1,675 mm automatic sheet metal deburring machine working in wet grinding process automatic magnetic filter system Wet sanding device Washing and drying facilities Maglev width: 200 mm Minimum length of small parts: 80 mm

VACUUM MASSAGER, INJECT STAR TYPE: MAGNUM 2600 Technical description: Serial number: 3730 Capacity: 2600 l Power supply: 380-440V/50-60 Hz, 3ph Power: 7 Kw Tumbler dimensions: 1300 x 2450 mm Dimensions: 3270 x 1850 x 1900 mm With this machine you are in a position to massage meat at any time, fully automatically and at maximum, so that the general appearance and flavour is improved, as well as the structural loosening up of the meat and the essential assimilation of both the natural juices and injected brine, by binding in, is achieved. HOMOGENEOUS BRINE DISTRIBUTION Sealing-in of Protein: The binding of the surface cells, seals off the inner moisture and prevents drying out. Optimum Protein-Water-Ratio: Whether you massage ham, shoulder, loin, tongue, belly, brisket or rough and fine fillings for cooked, boiled, raw and preserved sausage, whole chickens or chicken parts, fish or othe ...

High precision tower SCHAUBLIN type 150 TECHNICAL SPECIFICATIONS: Year: 1998 Number of axes: 2 X-axis stroke: 180 [mm] Z-axis stroke: 600 [mm] Z-axis fast forward speed: 4000 [mm/min] Tip distance: 600 [mm] Peak height: 150 [mm] Diameter allowed above the bench: 340 [mm] Permissible diameter above trolley: 177 [mm] Spindle nose: CAMLOCK D 1-4'' Inner pin cone: CM5 Spindle for clamping pliers: B32 Spindle passage diameter: 40 [mm] Mini speed. Pin: 55 [rpm] Maximum speed. Pin: 3000 [rpm] Pin power: 4 [kW] Cone: CM5 Metric pitch range: 0.25 - 14 [mm] English pitch range: 112 - 1/2" [nets/inch] Modular pitches: 0.12 - 7.5 [modules] Watering tray capacity: 29 [l] Installed capacity: 6 [kVA] Supply voltage: 400 [V] Dimensions: 1730 x 970 x 1300 [mm] Weight: 1250 [kg] EQUIPMENT INCLUDED: x1 visualization HEIDENHAIN type ND780 (2 axes) x44 SCHAUBLIN B32 clamp ...

Vertical 3-axis CNC machining center with nano precision Kern Pyramid Nano Year of construction: 2013 Heidenhain iTNC 530 Table size: 600 x 600 mm Table load: max. 250 kg Longitudinal travel: X 500 mm Transverse travel: Y 500 mm Vertical travel: Z 400 mm Smallest travel increment: 0.1 μm Feeds up to: X/Y/Z 30,000 mm/min. Rapid traverses up to: X/Y/Z 30,000 mm/min. Acceleration: X/Y/Z 10 m/s² Vector-controlled milling spindle: Spindle mount: HSK-25 Spindle drive power: 6.4 kW AC Spindle speeds: 500 - 50,000 rpm. Spindle torque (S1): max. 1.6 Nm Automatic tool changer: Tool magazine positions: 32-fold Tool holder: HSK-E25 Tool Ø (every second place free): max. 60 mm Tool length: max. 160 mm Tool change time: 3 sec. Chip-to-chip time: 6 sec. Machine weight: approx. 8,000 kg Machine height: LxWxH 2,850 x 3 ...

USED CENTRIFUGAL MOLECULAR DISTILLATION SYSTEM Manufacturer: MYERS VACUUM, Inc. Model: PILOT 15 LAB Throughput Capacity 10 - 80 lbs/hr (4.5 – 36.3 kg/hr) Type Continuous Pumping system ultimate pressure: 2 X 10-4 Torr Operating Pressure 10 -3 Torr to Atmosphere Mechanical Forepump >11 CFM High Vacuum Pump 320 L/sec of air at 250C. Power: 10-15 KW/ hour 3 phase wye” 115/208 V, 5 wire 50/60 HZ Available for 230, 415 or 460 Volt. Water: (20°C) 2 gal/min (7.6 L/min) Liquid nitrogen consumption: 0.5 liters/ hour (Utility consumptions may vary depending on process conditions) Dimensions: Height 69 Inches (1.75m), Width 34 Inches (.86m), Depth 59 Inches (1.5m) Net Weight 1300 lbs. (590kg) Centrifugal molecular distillation is a purification technique, which has gained wide acceptance in the chemical, food processing, pharmaceutical, and petroleum industries as well as t ...

Used small continuous dryer For drying sheet materials. Width approx. 0.80 m, length approx. 1.60 m Dimensions: Width c. 1.10 m, length 1.75 m, height c. 1.70 m Heating with Leister hot air unit up to 160°C with uniform outlet on dry material through perforated plate. Can be moved on wheels. Swivel control box. For an additional cost spray bridge as shown.

Machine with painted aluminum structure, equipped with Lexan protections complete with micro safety. Easy to clean and accessible. Technical data: Length mm 3750 Width mm 2700 Height mm 2080 Sliding surface height mm 700 – 1000 Weight Kg 1600 Voltage Volt 400 Frequency Hz 50 / 60 Current A 11 Mechanical speed carton / min 200 Production characteristics: Case length mm 75 – 350 Case width mm 140 – 450 Case height mm 120 – 350 Equipped with: one input product feeding belt; pneumatic product elevation group; stainless steel AISI 304S stacked product collection hopper with independent motorization; product introduction group with own motorization complete with encoder. The machine is also equipped with inclined carton magazine with a capacity of about 50 cartons; carton picking unit, with suction cup arm with independent motor complete with encoder; carton tr ...

Peddimat machining center for section steel Manufacturer: Peddinghaus Type: LC 1250 / TDK 1000/9F Year of construction: 1993 System consisting of: Longitudinal saw, drilling rig and marking system Long-cut saw Manufacturer: Peddinghaus Type: Peddimat LC 1250 Year of construction: 1993 Control panel Saw blade: Ø 1250 mm, Z = 5 Motorized mitre adjustment Hydr. Locking mechanism for mitre swivel in the range of 45 / 45° Kneeling Inlet and straightening device Interface for automatic saw blade feed and automatic miter adjustment Drilling rig Type: Peddimat TDK 1000/9F Vertical drilling unit with 3 spindles each incl. internal coolant supply Hole diameter max: 40 mm Peddimat roller feed system incl. measuring discs on the inlet and outlet sides automatic hold-down device each on the feed and discharge side automatic "Z" tower adjustment by DS servo  ...

connection value: 380/400 Volt connection frequency: 50 Hz weight: ca. 1.200 kg Heidelberg platen OHT with PRACMATIC conversion for imprinting in roll labels (roll to roll) - from roll to roll - Hot air drying The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

LeoMat Digitakt 330 SFR – Slitter/Rewinder/UV-Flexo/Laminating  Year of manufacture: 2011  Servo drive  Job memory up to 50 jobs  Register control: Semi- and fully rotary  electronic motor control  Electronic web edge control  Waste and misprint stop  Unwind shaft: d=76mm  Unwind diameter: 700mm  Rewind shaft: d=76mm  Rewind diameter: 550mm  Automatic web stop at machine stop  Flexo printing unit GALLUS EM 340  Web width: 340mmm  Cliché 1.14mm  Fully rotary register control including servo drive  Die-cutting and printing of materials  UV drying  Web width: 410mm  Laminating  Pressure station mounted on printing cylinder  Punching unit LeoMat L  Adaptation of the GALLUS R250 magnetic cylinder  Rotometrics impression cylinder  Grid rewind servo driven  Integrated edge trim sucti ...

web widht: 310 mm printing lenght: 300 mm printing widht: 310 mm connection value: 230 Volt Enables precise imprinting in prefabricated roll labels. - Flexo printing unit - UV-Drying - Electronic infeed control - Longitudinal cutter (razor blade cut) - Job storage Web widht max.: 315 mm Printing lenght max. 300 mm Printing widht max.: 310 mm unwind and rewind Roll diameter max.: 400 mm Shafts diameter: 76 mm Longitudinal cutter, cutting width min.: 16 mm Output/Speed: 30 m / min. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Trocker in retrofit version and with new Siemes S7-1200 control cabinet with touch panel. - Producer Cefla - Year of construction 1999/2022 - Working width 1.300 mm - Number of pallets 5 Stk. - Palettenlänge 7.470 mm - Useable pallet length 7.200 mm - Max. part height ~ 50 mm - Clearance height between the pallet 60 mm - Max. part length 7.200 mm - Fresh air 3.000 - 9.000 m³/h - Exit air 3.000 - 9.000 m³/h - Heat output ~ 45 kW - Drying temperature 30 Grad (optional 60) Grad - Incl. heat exchanger - Feed speed infinitely adjustable 2 - 10 m/min - Suitably for water based lacquer - Suitably for solvent based lacquer - Length 9.600 mm - Width 3.300 mm - Height 2.650 mm + 900 mm - Location, in stock - Voltage / HZ 400 / 50 - Voltage fluctuation max. +/- 5 % - With switch cabinet - Ohne Stellventile und Wasserpumpen

verfügbar ab ca. 09-2023 - Producer Elmag Superfici - Type ETC-3/2-5500 - Year of construction 2003 - Working width 1.300 mm - Number of pallets 50 Stk. - Max. part height ~100 mm - Clearance height between the pallet 120 mm - Measure: middle pallet - middle pallet 3.800 mm - Max. part length 5.200 mm - Number of adjustable temperature zone 2 Stk. - Fresh air 9.000 m³/h - Heat output max. 2 x 45.000 kcal/53 kW - Drying temperature ~ 55 - 60 Grad - Incl. heat exchanger - Throughput in u-shape - Infeed side left - Feed speed infinitely adjustable 2 - 10 m/min - Suitably for water based lacquer - Suitably for solvent based lacquer - Length 7.400 mm - Width 6.510 mm - Height 5.745 mm - Location, not in stock ab 09-2023 - Voltage / HZ 400 / 50 - Voltage fluctuation max. +/- 5 % - Ohne Stellventile und Wasserpumpen

Drying Station, AGE 2009

GALLUS EM 510 C  - Manufacturer: Gallus  - Machine type: EM 510 C  - Printing process: UV flexo printing  - Year of manufacture: 2006  - Working width: 520 mm  - Number of stations: 3, of which 3 can be used as punching stations and 2 as printing stations  - Speed: 150 m/min Equipment:  - Unwind - 76 mm  - Unwind diameter: 1,200 mm  - Web tension control (Arsoma)  - splice table  - Side edge control (E&L)  - insetter  - Hot air drying at station 1  - UV drying GEW E2C at station 2 incl. water-cooled impression cylinder  - Cooling unit for water cooling  - Turning cross (replica, not original, fixed placement)  - Grid take-off - and matrix rewind/grid take-up  - Pulling station with cross cutting and integrated slitting station with 2 squeezing knives  - Single sheet delivery  - Edelmann h ...

Equipped with: Muller Martini 201 18 Stations Gathering Machine, Book Block Feeder, Perfect Binder Muller Martini 3006-18 with Stream Cover Feeder with 18 Stations, Hot Melt Spine And Side Gluing With Pre-Melter, Spiral Lay Down Balance or Drying Converyor to Muller Martini 3670 Three Knife Trimmer with Cassettes for Quick Change, Stacker Delivery, Max. Size: 450x310mm, Max. Speed 6.000 Cycles/Hour, Max. Size Head/Tail: 420mm, Max. Size Spine/Front: 305mm, Production: 4.000 Books/Hour, Complete with All Standard Accessories

ega Plus - LF 330 Internal machine number: Vega Internal C3 number: Variant 10 Printing process: UV flexographic printing Printing units: 1 Own Coating Unit: No Printing ink: UV - flexographic printing ink Drying: UV - drying Painting-partial: No Painting-full: Yes / Flexosleeve Varnishes: Gloss varnish, matt varnish, TTF varnish, luminescent varnish Laminating: No Material width paper and foil: min.: 150 mm / max.: 340 Print width: max. 310 Printing performance: only punching max. 200 m/min., printing max. 70 m/min. max. rolls Ø - down: 1000 mm / max. rolls Ø - up: 400 mm punching width: max. 320 mm Print feed: min. 80T = 254 mm Print feed: max. 136T = 431.8 Format punching: Rotary WGR 240 punching units: 2 Flat punching: No Punching sheet: Yes Punching cylinder: No Airshock cylinder: No Upper punch: Yes Lower punch: Yes Sheet cutting (crosswise) / leaf cutter: No ...

Compounding machine Horizon MC-80 Two towers with vibrating table Government machine

AVAILABLE FROM THE END OF AUGUST 2023 3 MONTHS WARRANTY Offer consisting of: - Gathering tower VAC-100a - Gathering tower VAC-100m - Stacking lowering table ST-40 - Collection and folding unit ACF-30 - Saddle stitcher SPF-30 - Three-side cutter HTS-30 - long delivery LC-200 Horizon VAC-100a / Horizon VAC-100m / VAC-100m Suction air gathering machines - Technology: Touch & Work - Model: Suction and blowing air gathering tower - Number of stations: 6 - Error avoidance: error, double blade and jam control - Job memory: 9 memory locations for repeat jobs Programs: - Dual cycle (non-stop operation) - Zeroing (1x and 2x) - Brochure program - Block program - selective compilation - Format: max. 500x350mm; min. 148x120mm - Paper weight: 40-250g/sqm - Loading capacity: 55mm/ station - Speed: up to 9,500 sets/h - Electricity: 230V; 50/60Hz - 1,86kW - ...

Machine: Gallus R250 Internal Machines No.: 567 Internal C3 No.: Variant 5 Printing Process: Letterpress Printing Units: 5c+Varnish Own Coating Unit: YES Printing Ink: UV Printing Inks Drying: UV Drying Painting-partial: YES / Flexo-Cliché Painting-full-f.: YES / Flexo-Cliché Varnishes: Gloss Varnish, Matt Varnish, TTF Varnish, Luminescent Varnish Lamination: NO Paper material width: min. 130mm / max. 270mm Print width: max.: 255mm Printing capacity: max. rolls Ø - From: 700mm / max. rolls Ø - On: 700mm Punching width: max. 255mm Pressure feed: min. 304.8mm (96T) Pressure feed: max. 596.9mm (188T) Format punching: Flat & rotary WGR 220 Punching units: 1x flat / 1x rotary Flat Stamping: YES Punching Plate: YES Punching Cylinder: YES Airshock Cylinder: YES Upper punching: YES Bottom punching: YES with pass. Umfg. to the Upper Punches Sheet Cutting (Cross) / Sheet C ...

feed pressure: 10 bar liter capacity: 15,5 l/s total power requirement: 7,5 kW weight of the machine ca.: 0,2 t dimensions of the machine ca.: 0,8 x 0,7 x 1,0 m compact srew compressor - coldness drying divice Dry Energy Hybrid - Tank 500 ltr., 11 bar The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

with light barriers in the infeed area, the dryer only switches on when parts are detected by the light barrier, otherwise the dryer is in energy-saving standby mode with almost closed mirror halves. The cooling fan is frequency controlled and is controlled by temperature sensors. Operation via a Siemens panel. - Producer Venjakob - Type VEN DRY UV Surround - Year of construction 2012 - Standby operation % - Working width 1.300 mm - Operationside left - Number of lamp from top 1 Stk. - For mercury lamps - For edge drying - Electic capacity lamp 120 W/cm - Electic capacity lamp infinitely variable 50 - 120 W/cm - Length belt conveyor - Fan, exhaust air regalbar bis max. 3.200 m³/h - Feed speed adjustable 2,5 - 7,5 m/min - Length 2.000 mm - Width 2.700 mm - Total connection power ~ 22 kW - Location - Voltage / HZ 400/50

Clamping angle, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Material: steel -Dimensions: 245/202/H130 mm -Wall thickness: mm -Weight: 28 kg

Clamping angle, T-slot plate, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Dimensions: 1000/600/H400 mm -Groove: 45 mm -Weight: 700 kg

Clamping angle, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Material: steel -Plate thickness: 29 mm -Top thread: M12 -Dimensions: 345/200/H170 mm -Weight: 33 kg

Recycling machine trade AGICOM- Pedergnana OG: Cable recycling plant used consisting of single-shaft shredder MR1740; Granulator CGM4050; Zig Zag Separator; Turbine mill Ghibli 352; separator, filter tower; Throughput approx. 300 kg/h. Details on request!

OPG MyRay Hyperion X5 3D DVT Air Wall Model Orthopantomograph Panoramic X-ray Machine Item: digital 2D/3D panoramic X-ray machine, wall model Type: MyRay Hyperion X5 3D Air manufacturer: Cefla SC, Italy Year of construction: 07/2016 Properties: - Complete examination of the two dental arches in single scan for adults and children (reduced collimation). examinations of the jaw area with maxillary sinuses; local investigations of the region concerned - High-resolution CBCT examination (80 pm) with possible single scan of the complete dentition (FOV 10x10) or scanning of various limited sections (MultiFOV) for reduced exposure in the area to be examined - short wall column - 3 light sights, autofocus (automatic adjustment of the dose to the patient) - A single 3D/2D QuickScan sensor - MRI (Morphology Recognition Technology) - 2D Focus-Free - Up to 22 2D programs - Stable ...

Clamping angle, clamping table, clamping cube, clamping plate, clamping tower, clamping box, measuring chimney -Top thread: M12 -Groove: 13 x 134 mm -Dimensions: 220/330/H280 mm -Weight: 28 kg

- Producer Venjakob - Type VEN DRY RZG - Working width 1300 mm - Max. part height 80 mm - Length of flash off tunnel 5000 mm - Volume flow air 5000 m³/h - Heat output 82 kW - Drying temperature 45 Grad - Incl. heat exchanger 90/70 Grad - Transport belttransport 5.200 mm - Location, in stock - Voltage / HZ 400 / 50

Key data: 125

Sell a total of 8 clamping towers from Allmatic, each with 4 Allmatic vices installed 5 of which TC 125 3 pieces of which NC 125 Condition: Used

Console, base body, device, clamping angle, clamping table, clamping cube, clamping plate, clamping tower -Price: per piece -Number: 2x available -Console: as a base for fixtures -Dimensions: 720/350/H910 mm -Weight: 170 kg

Gebr. Mixing plant / tower plant Fabr. Krupp, control company Dorner, 1 x mixer THZ 3000 Teka, 1 x mixer THZ 1000 Teka, with 4 cement silos, hot water supply via biomass heating possible, aggregate storage in the tower, Feeding via elevator/vibrating chute and distribution belts, recycling plant with two separate agitator basins

Drying centrifuge: 1 x 0.5 m Ø diam. Engine: 30 Kw (40 hp) at 2940 rpm.

Rack trolleys, paint drying trolleys, compartment trolleys, transport trolleys, shelf trolleys -Total length: 1190 mm -Total depth: 720 mm -Total height: 1800 mm -Weight: 66 kg

SWAN RAKOBAK 1500 Smoke System, Smoker, Smoke Chamber Smoke Chamber Smoking system / smoker SWAN RAKOBAK 1500 TYPE: RAKOBAK 1500-E-100 /P3000 Specifications: 400 V / 50Hz / 50 A Nominal capacity: 1500 liters Year of construction: 2008 Heating: Electric Nine-heat load 28 kW Functions: Redness, Drying, Cold Smoke, Hot Smoke, Smoking, Cooking, Baking, Air Conditioning, Shower, Cleaning, Rinsing 3-speed circulating fan Separate smoke generator for friction smoke Height: 90 cm Dimensions smoke chamber: HxWxD = 245 x 126 x 125 cm (width plus control 25 cm) Dimensions smoke generator: HxWxD = 125 x 60 x 115 cm Dimensions smoking trolley: HxWxD = 148.5 x 98 x 80 cm Door hinge on the right original wiring diagram is included The system is in stock ready for shipment. Good condition. The system was in operation until recently and needs to be reconnected by a professional ...

Smoke system Schich with 2 chambers, shop smoke system, drying, hot smoking, cooling, with large extractor hood, smoke generator for wood chips, with some smoke sticks and grilles, insertion size 1/1GN, Overall dimensions WxDxH approx. 150x81x250cm, weight approx. 490kg, used, functional

Stock# UG6361 Used stainless steel double cone vacuum dryer blender made in China, type SYZG-50. Contact parts made of stainless steel AISI 316L. Total capacity of the chamber is 50 l. Working volume is up to 25 l and the load weight ranges from 10 kg to 25 kg. Drying chamber is designed to operate at a pressure up to -1 bar and is equipped with an internal vacuum pipe. The drum is covered with 2 kW electric heating mats and is insulated with wool and is covered with SS AISI 304 on the outside. Inlet and outlet are equipped with lockable covers. Drum working speed up to 6 rpm. The chamber is mounted on frame made of stainless steel. Device is equipped with an local electric control panel and a vacuum pump with a water ring. Overall dimensions: length 1500 mm, width 1250 mm, height 750 mm, weight 400 kg.

This is a Stainless Steel SS (INOX) basket centrifuge separator, filtering - drying machine. It can be used for clothes dryer, professional laundring and other filtrating application. All material that are in contact with the centrifuge are made out of Stainless Steel. It has a big basket with 120cm Diameter and 60cm Height. The machine weighs approx. 2 tons without the control panel. It is in good working condition and it comes direcly from service with new air suspension (airsprings). It comes as a complete unit with it's PLC and Inverter.

"Basket Centrifuge for material drying and liquid separation, in very good condition, ready for use. Unit Specifications: - Basket capacity 60liters (φ50 Χ 300mm) - Basket is made out of Aluminum and the side wall Inox SS - Total dimensions Length 1000mm X Width 700mm X Height 750mm - Basket rotation 1260rpm - Motor power 1,5hp - Liquid exit 1"" inch - Good balance for minimum turbulance"

OPTIMUM D460X1500 tower Optimum brand universal lathe suitable for tools, fixture construction, forming and mold making. circumference diameter above the bed: 460 mm. Speed 25-2000rpm Year of construction / Yom 2014 passage 58mm Sp Height 230mm Tailstock MK 4 tip width 1500mm 5.5kw motor Speed 25-2000rpm Dimensions 2750X1080X1370mm